Lumishore ECLIPSE SNL100 Neon Flex Light, 1m, 12V, IP68, RGB

Overview

The Lumishore 010-04534-00 is a 1 m ECLIPSE Neon Flex SNL100 RGB strip light that creates a continuous line of color without visible LED dots. It runs on 12V DC only (10 to 15 V DC) and draws up to 0.5 A (6 W) for the full 1 m length, which keeps it straightforward to power from a typical onboard lighting circuit.

The strip is IP68-rated and fully encapsulated, which helps it handle washdowns, vibration, and saltwater exposure. With an illuminated cross section of 12.0 mm x 6.1 mm, it tucks neatly under gunwales, along steps, behind coamings, or in a cockpit recess where you want accent light without bulky fixtures.

RGB control is handled through an ECLIPSE Command Center, supporting on/off, dimming, and zone control, plus color selection and sound-to-light functionality when that feature is enabled in your system.

Key features

• 1 m RGB neon flex strip with 120 RGB LEDs per meter and a spot-free diffuser for a line of light that looks continuous
• 12V DC only (10 to 15 V DC) with up to 0.5 A draw for the 1 m run (6 W)
• IP68 ingress protection with construction that is fully encapsulated and potted; UV resistant and salt-spray tested
• Cut-to-length format in 25 mm steps, with sealing required before installation after trimming
• Simple 4-wire electrical installation; cable entry can be configured from the bottom or the side (fit and seal before installation)
• ECLIPSE Command Center control for on/off, dimming, zone control, color selection, and sound-to-light functionality
• Illuminated cross section of 12.0 mm x 6.1 mm; end cap dimensions of 14.0 mm x 8.0 mm for recess planning
• 3-year warranty

What's included

• 1 m Neon Flex SNL100 RGB strip light
• End sealing kit for cut-to-length installs

Installation and setup

Lay the strip out straight before cutting, mark the nearest cut point, and trim only at a marked cut location. After cutting, seal the new end before the strip goes on the boat, then mount it using stainless steel screw clips or a suitable channel that supports the strip without pinching it.

Handle it like a lighted extrusion rather than a rope light: side-bend only, avoid twisting, and keep bends gentle. The minimum bend radius is 120 mm in the vertical axis. The material is UV resistant, but avoid mounting where it will sit in strong direct sunlight.

It can be installed indoors, in partially covered areas, and in locations that get wet, but it is not intended to be permanently submerged.

Electrical and control integration

This strip is a 12V DC load with a 4-wire connection. For RGB operation it must be used with an ECLIPSE Command Center; it is not wired directly to a basic on/off switch.

When you are planning multiple runs, keep each lighting type on its own Command Center zone output, and note that a zone supports up to 20 m of Neon Flex.

Use cases on board

This setup makes sense for boats that already have an ECLIPSE Command Center and want a clean accent line in the cockpit, around seating bases, under gunwales, or along cabin features where you do not want individual point lights. It is also a good match for refits where space is tight and you need a slim profile that still looks finished once installed.

Maintenance and care

Rinse with fresh water after heavy salt exposure and clean with mild soap and a soft cloth. Periodically check mounting points, cable routing, and any sealed cut ends to make sure everything stays tight and watertight.

Shipping
We ship worldwide from the United States. Rates are calculated at checkout based on destination and package weight. Some items include free shipping, which will show automatically. Not every product is eligible for international shipping; checkout will confirm eligibility. We do not ship to PO Boxes except through USPS, and not all packages qualify.

Processing and dispatch
Most orders are verified, packed, and handed to the carrier within 1 to 2 business days. Some products may need extra handling time or ship directly from the manufacturer. For certain international orders, inventory transfers between warehouses may add time. If any delay is expected, we will let you know the dispatch date.

Delivery and tracking
Deliveries are handled by trusted carriers such as USPS, UPS, FedEx, and DHL. Estimated arrival times appear at checkout and depend on your location and the service you choose. These are estimates and can be affected by customs or carrier disruptions. A shipping confirmation with a tracking link is emailed when your order ships, and tracking may take up to 24 hours to update. You can also view tracking in your account.

Duties, taxes, and support
International customers are responsible for any customs duties, taxes, and fees charged by the destination country. If these charges are refused and a shipment returns to us, the carrier’s return cost and any re-entry customs fees will be deducted from the refund. If your order is late or you need help, contact cs@qualityboatparts.com and we will assist you.

Quality Boat Parts is a reseller. Many items include a manufacturer’s warranty, and all warranty service is handled directly by the manufacturer. We do not manage or administer warranty claims on behalf of customers.

Warranty terms, coverage, and duration are set by each manufacturer. Issues involving defects, repairs, or replacements must be addressed with the manufacturer’s support team. When available, the warranty period is listed on the product page. If it is not shown, contact us or the manufacturer for details before purchasing.

To start a claim, the customer must contact the manufacturer and follow their process. Keep your proof of purchase and original packaging, and register the product if the manufacturer requires it, as these are often needed for warranty service.

We are happy to help you find the right contact or documentation, but we cannot decide outcomes or intervene in claim resolutions. For guidance, email cs@qualityboatparts.com.