Lumishore ECLIPSE SNL100 Neon Flex Strip Light, White 5000K, 1m, 12V DC, IP68, 60 LEDs/m

Overview

The Lumishore 010-04492-00 is a 1 m ECLIPSE Neon Flex SNL100 strip light that puts out a continuous white line of light at 5000 K with a diffuser that hides individual LEDs. It is for 12 V DC systems only (10 to 15 V DC) and draws up to 0.5 A per meter (6 W per meter), which helps when you are sizing the circuit and voltage drop.

The light is sealed to an IP68 rating with an encapsulated, potted construction that holds up to washdowns, UV exposure, and vibration. It can be mounted inside or outside, including wet areas, but it is not intended for permanent submersion.

Key features

• 1 m length that can be trimmed in 25 mm increments and resealed for a clean finish
• White output at 5000 K with 60 LEDs per meter behind a spot-free diffuser
• 12 V DC only operating range (10 to 15 V DC)
• Up to 0.5 A per meter draw (6 W per meter) for straightforward circuit planning
• IP68 rating with fully encapsulated and potted construction, plus UV resistance and salt spray testing
• Low-profile illuminated cross section of 12.0 mm x 6.1 mm for tight mounting locations
• Side-bend installation with a 120 mm minimum bend radius; avoid twisting or bending in the other axis
• Stainless steel clip mounting with typical clip spacing around every 300 mm, with extra support around tighter curves
• On/off control from a basic switch, or dimming and zone control when used with an ECLIPSE Command Center

What’s included

• Neon Flex strip light (1 m)
• Stainless steel mounting clips
• Cable-exit end caps (bottom or straight style)
• Cut-and-seal kit for trimmed ends

Installation and setup

Lay the strip out straight before fitting it, then route it along the surface and snap it into the clips once the clip spacing is set. The strip bends on the side with a minimum radius of 120 mm; it should not be twisted or bent in the other axis.

If you need a shorter length, cut only at the marked cut points (25 mm steps) and seal the new end before the strip goes on the boat. Let the sealant cure undisturbed for 24 hours before exposing the end to water.

Electrical and control integration

For this single-color white strip, wiring is a simple two-wire connection to a fused 12 V DC lighting feed and ground. Keep connections in a protected location when possible and add strain relief so the cable is not carrying load at the end cap.

On/off control works from a standard switch. When the strip is run through an ECLIPSE Command Center, dimming and zone control can be handled through supported control interfaces.

Placement and use on board

Common installs include under gunwales, cockpit coamings, toe-kicks, hardtop overhangs, and cabin headliners where you want an even line of light without hotspots. It is a good match for boats running 12 V house power that want accent lighting that can follow gentle curves and fit into trim gaps.

Maintenance and care

Rinse after salt use and wipe with mild soap and water. Periodically check clip tightness and the sealed ends, especially in high-vibration areas.

Shipping
We ship worldwide from the United States. Rates are calculated at checkout based on destination and package weight. Some items include free shipping, which will show automatically. Not every product is eligible for international shipping; checkout will confirm eligibility. We do not ship to PO Boxes except through USPS, and not all packages qualify.

Processing and dispatch
Most orders are verified, packed, and handed to the carrier within 1 to 2 business days. Some products may need extra handling time or ship directly from the manufacturer. For certain international orders, inventory transfers between warehouses may add time. If any delay is expected, we will let you know the dispatch date.

Delivery and tracking
Deliveries are handled by trusted carriers such as USPS, UPS, FedEx, and DHL. Estimated arrival times appear at checkout and depend on your location and the service you choose. These are estimates and can be affected by customs or carrier disruptions. A shipping confirmation with a tracking link is emailed when your order ships, and tracking may take up to 24 hours to update. You can also view tracking in your account.

Duties, taxes, and support
International customers are responsible for any customs duties, taxes, and fees charged by the destination country. If these charges are refused and a shipment returns to us, the carrier’s return cost and any re-entry customs fees will be deducted from the refund. If your order is late or you need help, contact cs@qualityboatparts.com and we will assist you.

Quality Boat Parts is a reseller. Many items include a manufacturer’s warranty, and all warranty service is handled directly by the manufacturer. We do not manage or administer warranty claims on behalf of customers.

Warranty terms, coverage, and duration are set by each manufacturer. Issues involving defects, repairs, or replacements must be addressed with the manufacturer’s support team. When available, the warranty period is listed on the product page. If it is not shown, contact us or the manufacturer for details before purchasing.

To start a claim, the customer must contact the manufacturer and follow their process. Keep your proof of purchase and original packaging, and register the product if the manufacturer requires it, as these are often needed for warranty service.

We are happy to help you find the right contact or documentation, but we cannot decide outcomes or intervene in claim resolutions. For guidance, email cs@qualityboatparts.com.