Lumishore ECLIPSE SNL100 Neon Flex LED Strip Light, Blue Light, 2.5m, 12V DC, IP68, 60 LEDs/m, UV Resistant

Overview

The Lumishore 010-04490-00 is a 2.5 m ECLIPSE SNL100 Neon Flex strip light that runs on 12V DC only (10 to 15V DC) and produces a continuous blue line with no visible LED dots. It uses 60 blue LEDs per meter and is fully encapsulated and potted behind a spot-free diffuser for a clean, even glow.

The strip is rated IP68 and is suited to indoor use, outdoor use, and partially covered areas where it will see spray, vibration, and routine washdowns. It can be installed in wet areas, but it is not intended to live permanently submerged.

For planning clearances, the illuminated cross section is 12.0mm x 6.1mm and the end cap measures 14.0mm x 8.0mm. The strip can be cut to length in 25mm steps, but the cut end must be sealed before installation to keep the strip watertight.

Key features

• 2.5 m (98 in) blue Neon Flex strip light for accent lines along gunwales, headliners, steps, and T-top framing
• 12V DC only operation (10 to 15V DC), with max draw of 0.5A per meter (6W per meter)
• IP68-rated, fully encapsulated and potted construction with a diffuser that keeps the light as a continuous line
• Cut-to-length in 25mm steps, with sealing required at the cut end before installation
• Simple 2-wire hookup for basic on and off control
• Works with an ECLIPSE Command Center for on and off control plus dimming and zone control
• UV resistant and salt spray tested for typical marine exposure

Installation and setup

Lay the strip out straight before fitting so it can relax, then route it to the mounting location and mark the nearest cut point if you plan to trim it. Cut only on the marked cut points and seal the cut end before the strip goes on the boat. Mounting is done with stainless steel screw clips, and the cable can be routed with a bottom or side exit depending on the install.

Keep bends gentle and consistent. The strip has a 120mm minimum bend radius in the vertical axis, and it should not be bent in the horizontal axis or twisted. For runs longer than 1m, having a second person feed the strip while you fasten it helps prevent kinks and internal stress.

Electrical and system integration

This is a 12V-only light. Feed it from a protected 12V DC circuit and size wiring and fuse based on the full length you are powering. At the published maximum of 0.5A per meter, a 2.5m length can draw up to about 1.25A.

For basic installs, it connects as a 2-wire light and can be switched on and off. When paired with an ECLIPSE Command Center, the same strip can be dimmed and assigned to zones, and a zone can support up to 20m of Neon Flex. Keep single color, dual color, and RGB strips on separate zone outputs when using zoned control.

Compatibility and fit

Plan for the strip profile (12.0mm x 6.1mm) and for end cap clearance (14.0mm x 8.0mm) at the cable end. The strip suits straight runs and gentle curves along coamings, under-seat toe kicks, cockpit liners, and cabin overheads where you want a continuous blue line without point sources.

Use cases on board

This light makes sense for boats with a 12V house system that want blue accent lighting that stays clean-looking at night, even when the strip is in direct view. It fits well on fishing boats and cruisers where lighting gets sprayed down and where you want a low-profile strip tucked under edges rather than a bulky fixture.

Maintenance and care

Rinse salt off during routine washdowns and avoid harsh solvents that can attack plastics. Periodically check that clips are tight and that any sealed cut ends remain intact, especially in areas that see heat cycling and vibration.

Shipping
We ship worldwide from the United States. Rates are calculated at checkout based on destination and package weight. Some items include free shipping, which will show automatically. Not every product is eligible for international shipping; checkout will confirm eligibility. We do not ship to PO Boxes except through USPS, and not all packages qualify.

Processing and dispatch
Most orders are verified, packed, and handed to the carrier within 1 to 2 business days. Some products may need extra handling time or ship directly from the manufacturer. For certain international orders, inventory transfers between warehouses may add time. If any delay is expected, we will let you know the dispatch date.

Delivery and tracking
Deliveries are handled by trusted carriers such as USPS, UPS, FedEx, and DHL. Estimated arrival times appear at checkout and depend on your location and the service you choose. These are estimates and can be affected by customs or carrier disruptions. A shipping confirmation with a tracking link is emailed when your order ships, and tracking may take up to 24 hours to update. You can also view tracking in your account.

Duties, taxes, and support
International customers are responsible for any customs duties, taxes, and fees charged by the destination country. If these charges are refused and a shipment returns to us, the carrier’s return cost and any re-entry customs fees will be deducted from the refund. If your order is late or you need help, contact cs@qualityboatparts.com and we will assist you.

Quality Boat Parts is a reseller. Many items include a manufacturer’s warranty, and all warranty service is handled directly by the manufacturer. We do not manage or administer warranty claims on behalf of customers.

Warranty terms, coverage, and duration are set by each manufacturer. Issues involving defects, repairs, or replacements must be addressed with the manufacturer’s support team. When available, the warranty period is listed on the product page. If it is not shown, contact us or the manufacturer for details before purchasing.

To start a claim, the customer must contact the manufacturer and follow their process. Keep your proof of purchase and original packaging, and register the product if the manufacturer requires it, as these are often needed for warranty service.

We are happy to help you find the right contact or documentation, but we cannot decide outcomes or intervene in claim resolutions. For guidance, email cs@qualityboatparts.com.