Lumishore ORA TIX404 Thru-Hull Underwater LED Light, Interchangeable, White Light 6500K, 10.5-31V DC, IP68, 5,100 Fixture Lumens, 110° Beam, Bronze Body
Got questions? Ask an expert!
Know someone who needs this?
Share it with your crew or mechanic.
Overview
The Lumishore 010-04467-00 is an interchangeable thru-hull underwater LED light that runs on 10.5-31 V DC and produces single-color white light at 6500K. It throws a wide 110° beam and is rated at 5,100 verified fixture lumens, which helps create a broad light pool rather than a tight spotlight.
This is a two-wire light with the driver built into the unit, so there is no separate driver box to mount. The housing sits close to the hull with an 8 mm profile and uses a marine bronze body with a borosilicate glass lens for long-term underwater use.
If you are adding underwater lighting for docking visibility, a swim platform, or evening fishing, this model keeps the wiring simple while still delivering a bright white output.
Key features
- Single-color white output (6500K) with 5,100 verified fixture lumens and a wide 110° beam angle
- 10.5-31 V DC input for 12 V and 24 V systems
- Max current draw: 4.0 A on 12 V and 2.0 A on 24 V
- IP68 water-ingress rating for continuous submersion
- Two-wire connection with a built-in internal driver; on/off control from a standard switch
- Light face diameter is 88 mm with an 8 mm housing height for a low-profile look on the hull
- 57 mm (2.25 in) shaft hole cut-out; 64 mm (2.5 in) when using an isolation sleeve for metal or carbon-fiber hulls
- 3 m (9.8 ft) standard light cable length
- Marine bronze body with a borosilicate glass lens
Compatibility and fit
Plan around the hull cut-out and the inside clearance before you drill. The shaft hole cut-out is 57 mm (2.25 in) in standard installations, and the light face is 88 mm across. The shaft length is 136 mm, and a bonding connection is provided on the light because bonding is required.
For metal hulls or carbon-fiber builds, an isolation sleeve is used between the fitting and hull, and the recommended hole size increases to 64 mm (2.5 in). Make sure you have unrestricted access inside the hull so you can tighten the locking hardware and route the cable without strain.
Installation and setup
Install on a flat section of the hull where the light can sit flush. A common placement is 4 to 12 inches (100 to 300 mm) below the minimum loaded waterline, while keeping clear of exhaust outlets and other heat sources. When installing three or more lights, spacing of about 2.5 to 3 feet between lights helps keep the light pool consistent along the transom or hull side.
After drilling, seal any exposed core material inside the hole to prevent water intrusion into the laminate. Use a marine sealant around the thru-hull seat and shaft, and allow full cure time before final tightening.
Electrical and system integration
Wiring is straightforward: red is positive DC and black is ground. Each light should be individually protected with a fuse or breaker sized at 6 A for 12 V systems or 4 A for 24 V systems. All splices and connections should be made waterproof and supported so vibration does not work the wiring loose over time.
The cable can be extended when needed; choose the wire gauge so voltage drop stays under control over the full run, especially on longer transom-to-battery routes. Built-in protections such as reverse polarity protection and soft-start electronics help the light behave well on real boats where battery voltage can swing and loads come on and off.
Maintenance and care
Check the lens and housing regularly for marine growth, especially if the boat stays in the water. A soft cloth or a soft bristled brush is the right approach. Avoid abrasive pads, solvent-based cleaners, acids, alkalis, pressure washing, or sandblasting since those can damage the lens and sealing surfaces.
If the light is covered during maintenance or bottom work, keep it switched off until the covers are removed.
What's included
- One (1) ORA TIX404 light with built-in driver
Shipping
We ship worldwide from the United States. Rates are calculated at checkout based on destination and package weight. Some items include free shipping, which will show automatically. Not every product is eligible for international shipping; checkout will confirm eligibility. We do not ship to PO Boxes except through USPS, and not all packages qualify.
Processing and dispatch
Most orders are verified, packed, and handed to the carrier within 1 to 2 business days. Some products may need extra handling time or ship directly from the manufacturer. For certain international orders, inventory transfers between warehouses may add time. If any delay is expected, we will let you know the dispatch date.
Delivery and tracking
Deliveries are handled by trusted carriers such as USPS, UPS, FedEx, and DHL. Estimated arrival times appear at checkout and depend on your location and the service you choose. These are estimates and can be affected by customs or carrier disruptions. A shipping confirmation with a tracking link is emailed when your order ships, and tracking may take up to 24 hours to update. You can also view tracking in your account.
Duties, taxes, and support
International customers are responsible for any customs duties, taxes, and fees charged by the destination country. If these charges are refused and a shipment returns to us, the carrier’s return cost and any re-entry customs fees will be deducted from the refund. If your order is late or you need help, contact cs@qualityboatparts.com and we will assist you.
Quality Boat Parts is a reseller. Many items include a manufacturer’s warranty, and all warranty service is handled directly by the manufacturer. We do not manage or administer warranty claims on behalf of customers.
Warranty terms, coverage, and duration are set by each manufacturer. Issues involving defects, repairs, or replacements must be addressed with the manufacturer’s support team. When available, the warranty period is listed on the product page. If it is not shown, contact us or the manufacturer for details before purchasing.
To start a claim, the customer must contact the manufacturer and follow their process. Keep your proof of purchase and original packaging, and register the product if the manufacturer requires it, as these are often needed for warranty service.
We are happy to help you find the right contact or documentation, but we cannot decide outcomes or intervene in claim resolutions. For guidance, email cs@qualityboatparts.com.