{"product_id":"qbp981149","title":"Garmin Intelliducer NMEA 2000 Thru-Hull Depth\/Temp Transducer, 13-24 Degree Deadrise, 150W RMS, 900 ft Max Depth","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Garmin 010-00701-01 is a thru-hull Intelliducer that reports water depth and water temperature over an NMEA 2000 network for display on a compatible helm screen or instrument.\u003c\/p\u003e\u003cp\u003eThis version is matched to hulls with a 13-24° deadrise so the sensor face sits correctly once installed. Sonar operates at 160 kHz with 150 W (RMS) output and supports depth readings to 900 ft (275 m) depending on water and bottom conditions.\u003c\/p\u003e\u003cp\u003eIt draws power from the NMEA 2000 backbone (9-16 Vdc), uses LEN 4, and includes a 19 ft 8 in (6 m) NMEA 2000 drop cable. Overall size is 4 19\/32 in (116.3 mm) long x 4 in (101.4 mm) wide x 3 in (76.2 mm) deep.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eThru-hull mount for boats with a 13-24° deadrise, keeping the sensing element properly oriented in the water\u003c\/li\u003e\n\u003cli\u003eSends depth and temperature data directly on NMEA 2000, using standard network power (9-16 Vdc) and LEN 4\u003c\/li\u003e\n\u003cli\u003e160 kHz depth sounder with 150 W (RMS) output and depth capability up to 900 ft (275 m) in suitable conditions\u003c\/li\u003e\n\u003cli\u003eIncludes a 19 ft 8 in (6 m) NMEA 2000 drop cable for routing from the backbone to the sensor location\u003c\/li\u003e\n\u003cli\u003eCompact footprint for typical bilge and under-sole installations, with a housing size of 4 19\/32 in x 4 in x 3 in\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eWhat’s included\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eThru-hull Intelliducer (top and bottom sections)\u003c\/li\u003e\n\u003cli\u003eGasket and locking ring\u003c\/li\u003e\n\u003cli\u003eNMEA 2000 drop cable\u003c\/li\u003e\n\u003cli\u003eNMEA 2000 T-connector\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis sensor is intended for fiberglass and metal hulls. It is not intended for wood hull installations, where swelling can damage the fitting. Deadrise match matters on a thru-hull installation, so confirm your hull angle at the mounting location falls in the 13-24° range before drilling.\u003c\/p\u003e\u003cp\u003eOn the network side, it connects as an NMEA 2000 device and transmits water depth and temperature (including PGNs 128267 and 130312). It suits installations where you want numeric depth and temperature data on your display rather than fish targets or bottom contour imagery.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003ePlan the mounting spot with the same care as any thru-hull: pick a location with clean water flow, keep it away from intakes and discharges, and avoid areas with turbulence from shafts or propellers. A position close to the keel is commonly used, as long as there is safe access inside the hull for tightening and future service.\u003c\/p\u003e\u003cp\u003eInstall with an appropriate marine sealant and align the body so the keel indicator points toward the keel. After launch, check for leaks immediately and continue to inspect the installation during the first day in the water.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eKeep the submerged surface clean so growth does not interfere with readings. A mild detergent and a lightly used scour pad are suitable for routine cleaning, and avoiding scratches helps the sensor stay accurate.\u003c\/p\u003e\u003cp\u003eIn saltwater, coating the submerged surface with a water-based antifouling paint helps reduce fouling. Recoat as part of seasonal maintenance.\u003c\/p\u003e\u003ch6\u003eUse cases on board\u003c\/h6\u003e\u003cp\u003eThis setup makes sense for coastal cruisers, fishing boats, and sailboats that want depth and temperature shown at the helm over NMEA 2000 without adding a full fishfinder-style transducer. It also works well on boats where the thru-hull location is fixed by construction and you need the 13-24° deadrise match at that spot.\u003c\/p\u003e","brand":"Garmin","offers":[{"title":"Default Title","offer_id":52269002227893,"sku":"QBP981149","price":209.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1298743_qbp981149.jpg?v=1771541411","url":"https:\/\/www.qualityboatparts.com\/products\/qbp981149","provider":"Quality Boat Parts","version":"1.0","type":"link"}