{"product_id":"qbp967001","title":"Garmin OnDeck Relay Switch, For OnDeck Hub, 24Vdc, Up to 8A","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Garmin 010-13009-07 is a 24 Vdc relay switch that lets you turn a DC accessory on and off through a Garmin OnDeck Hub. The control side operates on 15.6 to 31.2 Vdc, and the switched contacts are rated for loads from 0.1 A up to 8 A at 20 to 32 Vdc (up to 9 A at 10 to 16 Vdc).\u003c\/p\u003e\u003cp\u003eOnce it is wired and configured in the OnDeck system, the switch can be controlled from the ActiveCaptain app and from compatible Garmin chartplotters. A single OnDeck Hub can support up to five relay switches, which is handy when you want separate control of a few circuits rather than tying everything into one feed.\u003c\/p\u003e\u003cp\u003eThis is a good fit for 24 V boats that already have an OnDeck Hub installed and want remote on and off control for a modest-load circuit such as lighting, a fan, a small pump, or powering a network segment, as long as the current draw stays within the relay rating.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e24 V control voltage range: 15.6 to 31.2 Vdc on the relay coil side\u003c\/li\u003e\n\u003cli\u003eSwitching capacity: 0.1 A minimum load; up to 8 A at 20 to 32 Vdc (up to 9 A at 10 to 16 Vdc)\u003c\/li\u003e\n\u003cli\u003eSupports up to five relay switches on one OnDeck Hub\u003c\/li\u003e\n\u003cli\u003eSwitch control available through the ActiveCaptain app and on compatible Garmin chartplotters after configuration\u003c\/li\u003e\n\u003cli\u003eOperating temperature range: -15 to 85 C (5 to 185 F)\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eMount the relay where it stays dry and is protected from spray, typically near your DC distribution point so the high-current wiring runs are short. Secure it so it cannot move or chafe as the boat pounds, and keep wiring supported with proper strain relief.\u003c\/p\u003e\u003cp\u003eOn the wiring side, think of this as two parts: a low-current control connection into the OnDeck system, and a separate set of contacts that switch your accessory circuit. Label both ends while you work so the switch name in the app matches what it actually controls at the panel.\u003c\/p\u003e\u003ch6\u003eElectrical and system integration\u003c\/h6\u003e\u003cp\u003ePlan the switched circuit like any other onboard DC branch: fuse it correctly, choose wire gauge based on current and run length, and keep all connections clean and tight. Stay within the contact ratings, especially with devices that have a high inrush current.\u003c\/p\u003e\u003cp\u003eIf you are switching inductive loads like a solenoid or small motor, follow the device maker guidance for suppression and wiring practices to reduce arcing and electrical noise.\u003c\/p\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis relay switch is for OnDeck systems running on a 24 V supply, with the control side requiring 15.6 to 31.2 Vdc. If your boat and OnDeck Hub are powered from a 12 V house bank, this is not the right relay version for the control side.\u003c\/p\u003e\u003cp\u003eOn the load side, it can switch either 12 V or 24 V circuits as long as the current and voltage stay within the published contact ratings, but it is typically used in 24 V installations to match the onboard system voltage.\u003c\/p\u003e\u003ch6\u003eUse cases on board\u003c\/h6\u003e\u003cp\u003eOwners commonly use an OnDeck-controlled relay for deck or cockpit lighting, a cabin fan, a small utility pump, or powering a piece of equipment that you want off when the boat is unattended. It is also useful when you want a controlled feed to a subsystem that otherwise would be left energized at the dock.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eRecheck terminals after the first few outings, then inspect periodically for corrosion, looseness, or chafe. If the relay is in a locker that sees moisture, keeping connections sealed and supported will do more for long-term reliability than anything else.\u003c\/p\u003e","brand":"Garmin","offers":[{"title":"Default Title","offer_id":52269134971061,"sku":"QBP967001","price":69.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1299370_qbp967001.jpg?v=1771542113","url":"https:\/\/www.qualityboatparts.com\/products\/qbp967001","provider":"Quality Boat Parts","version":"1.0","type":"link"}