{"product_id":"qbp880657","title":"Vimar IDEA\/8000 Surface-Mount Enclosure, IP55, 1 Module, Grey","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Vimar VM13521 is an IP55 surface-mount enclosure sized for one 8000 standard module, finished in RAL 7035 grey.\u003c\/p\u003e\u003cp\u003eIt is used when you need to mount a single Vimar 8000 Series control on a bulkhead or panel and keep it protected in areas that see spray, dust, and routine wipe-downs. The insulating plastic body keeps the enclosure from corroding and helps avoid unwanted contact with live parts when installed correctly.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eIP55-rated enclosure to help protect a single module installation from dust and water jets\u003c\/li\u003e\n\u003cli\u003eSurface-mount format for one Vimar 8000 standard module\u003c\/li\u003e\n\u003cli\u003eRAL 7035 grey finish for a clean match with other 8000 Series hardware\u003c\/li\u003e\n\u003cli\u003ePlastic construction with insulating properties for marine and industrial mounting locations\u003c\/li\u003e\n\u003cli\u003eCompact footprint that works well for retrofits when you cannot recess a box into the structure\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis enclosure is built around the 8000 standard module format in a 1-module size. Before ordering, confirm the module style on your boat is 8000 standard and that your chosen mechanism and front hardware are intended for the same system.\u003c\/p\u003e\u003cp\u003eIf you are replacing an older surface box, check the available footprint on the mounting surface and plan cable routing so conductors are not forced into tight bends behind the module.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eMount it on a flat, rigid surface where the cover can open fully and the wiring can enter cleanly. On boats, that usually means a helm side panel, cockpit coaming, companionway bulkhead, or a sheltered area near deck equipment where a surface box is easier than cutting in a recess.\u003c\/p\u003e\u003cp\u003eFor wet areas, take the time to seal the cable entry and fasteners so water cannot track behind the enclosure. Leave a small drip loop in the cable run when possible so moisture does not run straight into the back of the box.\u003c\/p\u003e\u003ch6\u003eUse cases on board\u003c\/h6\u003e\u003cp\u003eThis is a good match for boats already using Vimar 8000 Series modules and needing a small, splash-resistant surface enclosure for a single control point. It is commonly used for one-off additions like a switch near a transom door, a control by the cockpit table, or a utility point in a sheltered locker.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eRinse salt residue off with fresh water and wipe the enclosure down during routine cleaning. If the box is installed in a high-traffic spot, check occasionally that the cover closes properly and that the mounting screws stay snug after vibration and temperature changes.\u003c\/p\u003e","brand":"Vimar","offers":[{"title":"Default Title","offer_id":52269529497781,"sku":"QBP880657","price":12.08,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1300376_qbp880657.jpg?v=1771544451","url":"https:\/\/www.qualityboatparts.com\/products\/qbp880657","provider":"Quality Boat Parts","version":"1.0","type":"link"}