{"product_id":"qbp866319","title":"Garmin OnDeck 2-Pin Power Cable, For OnDeck Hub, Threaded","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Garmin 010-13009-05 is a threaded 2-pin power cable for a compatible OnDeck Hub, used to tie the hub into your boat’s DC system.\u003c\/p\u003e\u003cp\u003eThe lead is 6 ft (1.8 m) and includes an in-line fuse holder with a 7.5 A, 42 V fast-acting fuse, which keeps protection right in the power feed instead of relying on a downstream fuse that may be overlooked later.\u003c\/p\u003e\u003cp\u003eThis is the replacement-style cable you use for a permanent install where the hub needs steady power for vessel monitoring.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eThreaded 2-pin connector with a locking ring to help prevent vibration from backing the connection off.\u003c\/li\u003e\n\u003cli\u003e6 ft (1.8 m) overall length for typical battery compartment to hub routing.\u003c\/li\u003e\n\u003cli\u003eIn-line fuse holder with a 7.5 A, 42 V fast-acting fuse for the hub power feed.\u003c\/li\u003e\n\u003cli\u003eBare-wire end for direct connection to a battery feed or a fused DC distribution point.\u003c\/li\u003e\n\u003cli\u003eExtension guidance supports longer runs up to 36 ft (11 m) when the correct wire gauge is used.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis cable fits the OnDeck Hub power port that uses a 2-pin threaded connection with a locking ring. It will not mate with Garmin Marine Network, NMEA 2000, or standard 2-wire power leads that do not have the threaded 2-pin connector.\u003c\/p\u003e\u003cp\u003eIf your hub’s power port looks different, confirm the connector style before ordering.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eRoute the cable from the hub to a clean 12 V or 24 V DC source. Connect the red wire to positive (+) and the black wire to negative (-), and keep the in-line fuse holder in place.\u003c\/p\u003e\u003cp\u003eFor monitoring when the engine is off, feed the hub from an always-on circuit rather than a keyed ignition circuit. Use watertight splices and heat-shrink where the bare-wire end could see moisture, and secure the run so the connector is not used as strain relief.\u003c\/p\u003e\u003ch6\u003eExtending the run\u003c\/h6\u003e\u003cp\u003eIf you need more length, extend the power run with the right wire gauge for voltage drop: up to 15 ft (4.6 m) use 10 AWG (5.26 mm2), up to 23 ft (7 m) use 8 AWG (8.36 mm2), and up to 36 ft (11 m) use 6 AWG (13.29 mm2). Keep the splice protected and out of wet locations whenever possible.\u003c\/p\u003e\u003ch6\u003eUse on board\u003c\/h6\u003e\u003cp\u003eThis is a good match for boats that rely on OnDeck for remote status checks and alerts while the vessel is at the dock, on a mooring, or in storage. A threaded power connection helps in lockers and under-helm installs where wiring sees engine vibration and occasional spray.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003ePeriodically check that the locking ring is hand-tight, the cable jacket is not chafed, and the fuse holder is clean and closing fully. Replace the fuse only with the same 7.5 A fast-acting type, and keep the wiring supported so movement is not carried by the connector.\u003c\/p\u003e","brand":"Garmin","offers":[{"title":"Default Title","offer_id":52269136937141,"sku":"QBP866319","price":29.99,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1299374_qbp866319.jpg?v=1771542128","url":"https:\/\/www.qualityboatparts.com\/products\/qbp866319","provider":"Quality Boat Parts","version":"1.0","type":"link"}