{"product_id":"qbp801076","title":"Garmin LiveScope Plus Perspective Mount, for LVS34 Transducer","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Garmin 010-13228-00 is a perspective mode mount that clamps to a trolling motor shaft and lets you run a LiveScope Plus LVS34 transducer in an overhead, looking-down view.\u003c\/p\u003e\u003cp\u003eIt is built to be repositioned on the water, so you can move the transducer between Forward, Down, and Perspective views without swapping brackets. Perspective view is recommended for shallow water, with a recommended depth up to 20 ft (6 m).\u003c\/p\u003e\u003cp\u003ePlan on updating both your chartplotter and the LiveScope system software as part of the install, then set the transducer orientation to Auto in the LiveScope installation settings so the view labels match the physical position.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eWorks with the LiveScope Plus LVS34 transducer to add an overhead Perspective view, plus Forward and Down positions.\u003c\/li\u003e\n\u003cli\u003eMount repositioning is done by swinging the arm and rotating the transducer to match the viewing-mode sticker.\u003c\/li\u003e\n\u003cli\u003eIncludes port-side and starboard-side setup options to match how your trolling motor stows.\u003c\/li\u003e\n\u003cli\u003eClamp-style shaft bracket installs on a trolling motor shaft, with an included rubber insert for 25 mm (1 in) shafts.\u003c\/li\u003e\n\u003cli\u003eUses the included hardware and hex wrench; the shoulder-bolt torque specification is 2.5 lbf-ft (3.4 N-m).\u003c\/li\u003e\n\u003cli\u003eCalls for a service loop in the transducer cable and secure routing with electrical tape or cable ties to avoid tight bends.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eWhat’s included\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003ePerspective mode mount components (shaft bracket and extension arm parts)\u003c\/li\u003e\n\u003cli\u003eMounting hardware (including M6 screws, shoulder screws, and washers)\u003c\/li\u003e\n\u003cli\u003eHex wrench\u003c\/li\u003e\n\u003cli\u003eRubber insert for 25 mm (1 in) trolling motor shafts\u003c\/li\u003e\n\u003cli\u003ePORT SIDE and STARBOARD SIDE stickers\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis mount is intended for the LiveScope Plus LVS34 transducer and is designed around a trolling motor shaft installation. It can be mounted on either the port or starboard side of the shaft, but the extension arm and sticker selection depends on how your trolling motor propeller sits when stowed.\u003c\/p\u003e\u003cp\u003eBefore tightening everything down, dry-fit the bracket and transducer so it does not interfere with stowing and deployment, and so the bracket orientation faces forward on the trolling motor as specified in the install setup.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eThe bracket clamps around the trolling motor shaft using the included M6 screws. If your shaft is 25 mm (1 in), install the rubber insert before tightening the bracket.\u003c\/p\u003e\u003cp\u003eAfter the bracket is secured, attach the extension arm and transducer with the included shoulder screws and washers, tightening to the specified 2.5 lbf-ft (3.4 N-m). Route the transducer cable with a service loop, then secure it so the cable is supported through steering travel and stow motion.\u003c\/p\u003e\u003cp\u003eFinish by setting Orientation to Auto on your compatible chartplotter in the LiveScope installation menu, then align the transducer to the sticker marks for the view you want to run.\u003c\/p\u003e\u003ch6\u003eUse cases on board\u003c\/h6\u003e\u003cp\u003eThis mount is a good match for anglers running LiveScope Plus on a trolling motor who want a fast way to switch into an overhead view when working shallow flats, docks, and cover, then rotate back to Forward or Down for tracking targets off the bow.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eRecheck fasteners after the first few trips, especially if the trolling motor sees hard waves or long runs. If you use the boat in brackish or salt water, a quick rinse helps keep the bracket and moving joints clean and easier to adjust.\u003c\/p\u003e","brand":"Garmin","offers":[{"title":"Default Title","offer_id":52269260505269,"sku":"QBP801076","price":149.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1299525_qbp801076.jpg?v=1771542894","url":"https:\/\/www.qualityboatparts.com\/products\/qbp801076","provider":"Quality Boat Parts","version":"1.0","type":"link"}