{"product_id":"qbp662886","title":"Garmin Reactor 40 Kicker Throttle Actuator Linkage Parts, For Carbureted Honda\/Yamaha\/Mercury\/Tohatsu Outboards","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Garmin 010-12827-02 is a set of throttle actuator linkage parts used to connect a Reactor 40 Kicker autopilot throttle actuator to the throttle linkage on compatible outboard engines. It is used when you need a physical connection between the actuator and a carbureted outboard throttle on Honda, Yamaha, Mercury, or Tohatsu applications.\u003c\/p\u003e\u003cp\u003eThis is the small but critical hardware that translates the actuator movement into smooth throttle changes at the engine. It is meant for a typical outboard engine compartment where parts see vibration, spray, and frequent access for service checks.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eLinkage parts that couple a Reactor 40 Kicker throttle actuator to an outboard throttle linkage\u003c\/li\u003e\n\u003cli\u003eIntended for carbureted outboards from Honda, Yamaha, Mercury, and Tohatsu\u003c\/li\u003e\n\u003cli\u003eHelps keep throttle actuation consistent by using a purpose-matched linkage geometry\u003c\/li\u003e\n\u003cli\u003eBlack finish to blend in with common engine rigging and brackets\u003c\/li\u003e\n\u003cli\u003eSeparate linkage parts are used for Suzuki and Yamaha EFI applications\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis linkage set is meant for carbureted outboards in the listed engine families. Fit on a specific motor comes down to the throttle arm layout, available attachment points, and whether there is clear travel through idle to wide-open throttle without the linkage contacting covers, cables, or harnesses.\u003c\/p\u003e\u003cp\u003eIf your engine is Suzuki, or a Yamaha with EFI, this is not the correct linkage style for that application. Use the linkage parts intended for those EFI setups so the attachment points and movement match the engine’s throttle hardware.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eInstallation is typically a straightforward mechanical hookup between the autopilot throttle actuator and the engine throttle arm. After mounting, the key is alignment: the linkage should move freely through the full range without binding, and it should not preload the throttle when the actuator is at neutral.\u003c\/p\u003e\u003cp\u003eOnce installed, cycle the throttle by hand and then through the actuator’s control to confirm you get clean idle return and full travel. Recheck fasteners and linkage movement after the first few hours of operation since outboard compartments see constant vibration.\u003c\/p\u003e\u003ch6\u003eUse on board\u003c\/h6\u003e\u003cp\u003eThis linkage is a good match when you are setting up a kicker autopilot system that can manage throttle for low-speed trolling or long runs where holding a steady pace matters. It is commonly used on fishing boats and multi-engine setups where a carbureted auxiliary outboard handles slow-speed work.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eGive the linkage a quick inspection during routine engine checks. Look for looseness at the connection points and any signs of wear where parts pivot or slide. A freshwater rinse after saltwater use helps keep moving parts free and makes it easier to spot corrosion or developing play early.\u003c\/p\u003e","brand":"Garmin","offers":[{"title":"Default Title","offer_id":52269266206901,"sku":"QBP662886","price":79.99,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1299481_qbp662886.jpg?v=1771542951","url":"https:\/\/www.qualityboatparts.com\/products\/qbp662886","provider":"Quality Boat Parts","version":"1.0","type":"link"}