{"product_id":"qbp642715","title":"Victron Energy Smart BMS CL 12-100 to MultiPlus Cable","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Victron Energy ASS070200100 is a control cable for connecting a Smart BMS CL 12-100 to compatible Victron MultiPlus inverter\/chargers in systems where the BMS does not use a VE.Bus interface. It lets the BMS control the MultiPlus through the remote on\/off connection, so the inverter\/charger can respond when the battery management system needs to protect the lithium battery bank.\u003c\/p\u003e\u003cp\u003eThis cable is used with MultiPlus 500VA-1600VA models, MultiPlus Compact 800VA-2kVA models, and MultiPlus-II models. It is also suitable for BMS products without a VE.Bus interface, including the Smart BMS CL 12-100 and smallBMS, using the Load\/Charge Disconnect or Load\/Charger outputs.\u003c\/p\u003e\u003cp\u003eFor boat electrical systems, this is a small but important integration part when adding or servicing Victron lithium battery protection around a MultiPlus. It belongs in a protected electrical area near the BMS and inverter\/charger, with wiring kept secure against vibration and away from moisture, heat, and chafe points.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eConnects a Victron Smart BMS CL 12-100 to compatible MultiPlus inverter\/charger models without using VE.Bus control.\u003c\/li\u003e\n\u003cli\u003eSupports MultiPlus 500VA-1600VA, MultiPlus Compact 800VA-2kVA, and MultiPlus-II installations.\u003c\/li\u003e\n\u003cli\u003eLets the BMS control the MultiPlus through the remote on\/off connector when battery protection conditions require action.\u003c\/li\u003e\n\u003cli\u003eWorks with the Smart BMS CL 12-100 Load\/Charge Disconnect output and the smallBMS Load\/Charger output.\u003c\/li\u003e\n\u003cli\u003eHelps the MultiPlus switch back on and begin charging after a low battery shutdown once the BMS side is reset and AC power is available.\u003c\/li\u003e\n\u003cli\u003eUseful for marine lithium battery upgrades where the inverter\/charger must follow the BMS rather than operate independently.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eThe cable is wired to the remote on\/off connector of the MultiPlus. On MultiPlus 500VA-1200VA models, the black wire connects to the ON terminal and the red wire connects to the positive terminal. On MultiPlus Compact 800VA-2kVA models, the black wire connects to the middle terminal and the red wire connects to the right IN terminal. On MultiPlus-II models, the black wire connects to the lower negative terminal and the red wire connects to the upper positive remote on\/off terminal.\u003c\/p\u003e\u003cp\u003eBoth the relevant BMS output and the MultiPlus remote input state must be correct for the MultiPlus to operate. After a shutdown caused by low battery voltage, the system can be reset by running the alternator or using a battery charger on the primary side of the BMS. Once reset, the MultiPlus can switch on and start charging when it is connected to an AC power source.\u003c\/p\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis cable is for Victron systems built around Smart BMS CL 12-100 or smallBMS control and a compatible MultiPlus inverter\/charger. It is not a general data cable and should not be treated as a replacement for VE.Bus communication where VE.Bus control is required by the system design.\u003c\/p\u003e\u003cp\u003eBefore installation, match the MultiPlus model family to the correct remote on\/off terminal wiring. This is especially important on refits, where older inverter\/chargers, lithium battery upgrades, and existing DC distribution wiring may already be in place.\u003c\/p\u003e\u003ch6\u003eUse cases on board\u003c\/h6\u003e\u003cp\u003eThis cable is a good match for cruising boats, fishing boats, and compact marine power systems using Victron LiFePO4 Smart Batteries with a Smart BMS CL 12-100 and a compatible MultiPlus. It is most useful when the battery management system needs direct authority over the inverter\/charger so battery protection events are handled cleanly.\u003c\/p\u003e\u003cp\u003eBecause this is a control connection rather than a power cable, careful routing matters. Keep it supported, avoid sharp bends, and install it where the terminals remain accessible for inspection during routine electrical checks.\u003c\/p\u003e","brand":"Victron Energy","offers":[{"title":"Default Title","offer_id":52023451877557,"sku":"QBP642715","price":17.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1332142_qbp642715.jpg?v=1780191809","url":"https:\/\/www.qualityboatparts.com\/products\/qbp642715","provider":"Quality Boat Parts","version":"1.0","type":"link"}