{"product_id":"qbp618805","title":"Lopolight 301-009 Port Sidelight, 2NM, 10-32VDC, IP68, Flat Base Mount","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Lopolight 301-009 series is a 2 NM red port sidelight for horizontal mounting, covering the 112.5° sector used for port-side navigation lighting on vessels up to 50 m (164 ft). It runs on 10 to 32 VDC for both 12 V and 24 V systems, with a 1.2 W draw (about 90 mA at 12 VDC and 50 mA at 24 VDC).\u003c\/p\u003e\u003cp\u003eThe FB (flat base) POM mounting system is built for horizontal surfaces where you want a clean footprint and a tidy cable exit. The assembly is rated IP68 and is built to stay sealed through spray, washdowns, and the vibration that comes with fast runs and rough water.\u003c\/p\u003e\u003cp\u003eHousing diameter is Ø92.5 mm. Height depends on the stack style: single stack is 36 mm tall, and double stack is 58 mm tall.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e2 NM red port sidelight with a 112.5° horizontal sector\u003c\/li\u003e\n\u003cli\u003e10 to 32 VDC input for 12 V and 24 V boats\u003c\/li\u003e\n\u003cli\u003e1.2 W draw (about 90 mA at 12 VDC, 50 mA at 24 VDC)\u003c\/li\u003e\n\u003cli\u003eIP68 rating with potted construction to help keep water out and handle vibration\u003c\/li\u003e\n\u003cli\u003eFB (flat base) POM mounting system for horizontal mounting locations\u003c\/li\u003e\n\u003cli\u003eAnodized aluminum housing (silver or black) with PMMA lens and A4 stainless steel screws\u003c\/li\u003e\n\u003cli\u003eApproved to COLREG72, EN14744, IEC 60945, IACS E10, and USCG (UL1104)\u003c\/li\u003e\n\u003cli\u003eOperating temperature range: -25°C to 55°C\u003c\/li\u003e\n\u003cli\u003eMinimum feed wire gauge: 0.5 mm2 (AWG 22)\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eVariants\u003c\/h6\u003e\u003cp\u003eThis light is offered in multiple configurations to match the finish and the stack style at the mounting point.\u003c\/p\u003e\u003cp\u003eFinish changes the look of the housing (silver or black). Style changes the overall height: single stack is 36 mm tall, and double stack is 58 mm tall.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e301-009-FB: Finish Silver, Style Single Stack. The 36 mm height keeps the light low on the mounting surface, which helps when clearance is tight under rails or overhangs.\u003c\/li\u003e\n\u003cli\u003e301-009-FB-B: Finish Black, Style Single Stack. The black finish reduces visual contrast on darker topsides while keeping the same low-profile height.\u003c\/li\u003e\n\u003cli\u003e301-009ST-FB: Finish Silver, Style Double Stack. The 58 mm height can be useful when the mounting spot sits near coamings or other features that could shadow the lens line.\u003c\/li\u003e\n\u003cli\u003e301-009ST-FB-B: Finish Black, Style Double Stack. Combines the taller stack with a black finish when you want the housing to blend in visually on deck.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eWhat’s included\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eNavigation light, pre-cabled\u003c\/li\u003e\n\u003cli\u003eInstallation guide\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eMount the light on the port side so the lens has a clear view across the required arc, with no obstruction from rails, davits, canvas, or deck gear. For horizontal mounting, the FB base sits on a flat surface such as a cabin top, mounting pad, or deck edge. Take a moment to check sightlines from ahead and from the beam before drilling, since small changes in placement can avoid shadows later.\u003c\/p\u003e\u003cp\u003eRoute the cable where it will not chafe and use a watertight pass-through if the wiring enters the deck or cabin top. Plan a small service loop so the light can be lifted for inspection without pulling on the cable.\u003c\/p\u003e\u003ch6\u003eElectrical and compliance\u003c\/h6\u003e\u003cp\u003eConnect to a 10 to 32 VDC navigation-light circuit. With low current draw, it integrates cleanly with standard nav-light switches and monitoring setups without putting much load on the circuit.\u003c\/p\u003e\u003ch6\u003eUse on board\u003c\/h6\u003e\u003cp\u003eThis series fits boats and yachts up to 50 m that need a 2 NM port sidelight in a horizontal-mount format, including refits where you want to keep the Ø92.5 mm footprint but change the finish or stack height to suit the mounting location.\u003c\/p\u003e","brand":"Lopolight","offers":[{"title":"Silver \/ Single Stack","offer_id":52271524905141,"sku":"QBP618805-V1","price":412.88,"currency_code":"USD","in_stock":true},{"title":"Black \/ Single Stack","offer_id":52271524937909,"sku":"QBP618805-V2","price":412.88,"currency_code":"USD","in_stock":true},{"title":"Silver \/ Double Stack","offer_id":52271524970677,"sku":"QBP618805-V3","price":795.6,"currency_code":"USD","in_stock":false},{"title":"Black \/ Double Stack","offer_id":52271525003445,"sku":"QBP618805-V4","price":795.6,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1309264_qbp618805.png?v=1771555205","url":"https:\/\/www.qualityboatparts.com\/products\/qbp618805","provider":"Quality Boat Parts","version":"1.0","type":"link"}