{"product_id":"qbp605349","title":"Lopolight 301-006 LED Stern Light, 2NM, Vertical Mount, 10-32VDC, IP68","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Lopolight 301-006 Series is a 2 NM white stern navigation light with a 135 degree sector and a vertical mount for vessels up to 50 m (164 ft). It runs on 10-32V DC and draws about 1.3 W (110 mA at 12V DC, 50 mA at 24V DC), which keeps the load light on typical 12V or 24V nav-light circuits.\u003c\/p\u003e\u003cp\u003eThe housing footprint is compact at 86.2 x 28 x 57.75 mm, making it easier to fit on a transom face, aft bulkhead, or another flat vertical surface where the stern sector has a clear view. The assembly is sealed to IP68 for wet stern conditions and washdowns, and it uses an anodized aluminum housing with a PMMA lens and A4 stainless steel mounting screws.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e2 NM white stern light with a 135 degree sector for vessels up to 50 m (164 ft)\u003c\/li\u003e\n\u003cli\u003eVertical surface mount with a compact body (86.2 x 28 x 57.75 mm)\u003c\/li\u003e\n\u003cli\u003e10-32V DC input for both 12V and 24V systems\u003c\/li\u003e\n\u003cli\u003eLow electrical load at about 1.3 W (110 mA at 12V DC, 50 mA at 24V DC)\u003c\/li\u003e\n\u003cli\u003eIP68 sealing for spray, rain, and washdowns around the stern\u003c\/li\u003e\n\u003cli\u003eAnodized aluminum housing (silver or black) with a PMMA lens and A4 stainless steel mounting hardware\u003c\/li\u003e\n\u003cli\u003ePre-attached cable in 6 m or 10 m lengths; minimum feed wire gauge 0.5 mm2 (AWG 22)\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eVariants\u003c\/h6\u003e\u003cp\u003eThis stern light is offered in a few configurations that change the housing finish and the factory cable length.\u003c\/p\u003e\u003cp\u003eAcross the range, the light output and electrical specs stay consistent: 2 NM visibility, a 135 degree white stern sector, vertical mounting, 10-32V DC input, IP68 sealing, and the same overall dimensions. The differences are the finish and how much cable is supplied for routing back to your nav-light circuit.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e301-006-6M: Silver finish, 6 m cable. A straightforward option for many installs where the run to the nav switch or junction point is moderate and you want to avoid adding extensions.\u003c\/li\u003e\n\u003cli\u003e301-006-B-6M: Black finish, 6 m cable. Useful when you want the light to blend with darker paint, hardware, or an aft structure while keeping the same cable reach.\u003c\/li\u003e\n\u003cli\u003e301-006 10M: Silver finish, 10 m cable. Helps on longer cable routes through an arch, tower, or larger aft sections where extra slack makes clean routing easier.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eMount the light on a flat vertical surface at the stern with the sector aimed aft and unobstructed by rails, davits, outboards, or a swim platform. Keep the cable run supported and protected from chafe, especially where it passes through the transom or into lockers, and seal any penetrations to prevent water intrusion.\u003c\/p\u003e\u003cp\u003eThe supplied mounting screws are M6 x 8 mm. If your mounting surface requires different fasteners or backing hardware, match the thread and use stainless hardware suitable for the structure.\u003c\/p\u003e\u003ch6\u003eElectrical and system integration\u003c\/h6\u003e\u003cp\u003eWire the light into a 10-32V DC navigation-light circuit (12V or 24V). With a low current draw, it typically fits comfortably on existing nav-light breakers and switches, but the circuit should still be protected and wired to marine practices for your vessel.\u003c\/p\u003e\u003cp\u003eIf you need to shorten or splice the cable, make the connection in a dry, accessible location using sealed connectors or a watertight junction, and keep splices out of bilge water paths and high-splash areas.\u003c\/p\u003e\u003ch6\u003eCompliance and operating limits\u003c\/h6\u003e\u003cp\u003eApproved to COLREG72 and EN14744, with additional approvals including IEC 60945, IACS E10, USCG, ABS, M.E.D., DNV, and LR. Operating temperature range is -25°C to 55°C.\u003c\/p\u003e\u003ch6\u003eWhat’s included\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eNavigation light with attached cable (length depends on variant)\u003c\/li\u003e\n\u003cli\u003e2 mounting screws (M6 x 8 mm)\u003c\/li\u003e\n\u003cli\u003eInstallation guide\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eUse on board\u003c\/h6\u003e\u003cp\u003eThis is a practical fit for powerboats and sailboats that need a compact stern light on a vertical face at the transom or aft superstructure. It also suits refits where low draw and an extended factory cable help tidy up the wiring run back to the nav-light switch panel.\u003c\/p\u003e","brand":"Lopolight","offers":[{"title":"Silver \/ 6M","offer_id":52371114295477,"sku":"QBP605349-V1","price":558.24,"currency_code":"USD","in_stock":false},{"title":"Black \/ 6M","offer_id":52371114328245,"sku":"QBP605349-V2","price":558.24,"currency_code":"USD","in_stock":false},{"title":"Silver \/ 10M","offer_id":52371114361013,"sku":"QBP605349-V3","price":578.46,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1319869_qbp605349.webp?v=1774060152","url":"https:\/\/www.qualityboatparts.com\/products\/qbp605349","provider":"Quality Boat Parts","version":"1.0","type":"link"}