{"product_id":"qbp513398","title":"Hella Marine Mini Lightbar LED Warning Light Bar, Magnetic Mount, 10-30V, 16 in, Amber Light, Clear Lens, Flashing and Rotating, IP6K9K, SAE J845 Class 1","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Hella Marine 014565121 is a 16 inch LED mini lightbar that puts out an amber warning signal on 10 to 30 VDC (12V or 24V) systems. It supports flashing and rotating patterns and is sealed to IP67 and IP6K9K for rain, spray, and washdowns.\u003c\/p\u003e\u003cp\u003eThis version uses a magnetic mount for temporary placement and a 10 ft cord with an inline switch and DC plug, so it can be moved between the dock, the truck, and the boat as needed. At full output it draws up to 6.1 A on a 12 V system (2.8 A on 24 V), so plan power and circuit protection accordingly.\u003c\/p\u003e\u003cp\u003eOn board, it is commonly used as a supplemental warning light during towing, docking assistance, deck work, or when a service craft needs to be seen clearly in the marina. It is not a substitute for required navigation lights; use it only when appropriate for local rules and operating conditions.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eAmber LED warning output with a clear polycarbonate dome for wide-angle visibility.\u003c\/li\u003e\n\u003cli\u003e10 to 30 VDC input to suit both 12V and 24V electrical systems.\u003c\/li\u003e\n\u003cli\u003eMultiple user-selectable patterns, including flashing and rotating modes.\u003c\/li\u003e\n\u003cli\u003eMagnetic mounting base for quick, temporary placement on a steel surface.\u003c\/li\u003e\n\u003cli\u003e10 ft power cord with inline switch and DC plug for a power outlet connection.\u003c\/li\u003e\n\u003cli\u003eIP67 and IP6K9K sealing to handle heavy spray, rain, and washdowns.\u003c\/li\u003e\n\u003cli\u003ePolarity reversal protection and an operating temperature range from -40 C to +65 C.\u003c\/li\u003e\n\u003cli\u003eEMC protection to ECE-R10 and CISPR 25 Class 3 to help reduce electrical noise issues.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eWhat’s included\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e16 inch LED mini lightbar with magnetic mount\u003c\/li\u003e\n\u003cli\u003e10 ft power cord with inline switch and DC plug\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis is a portable magnetic-mount lightbar, so it needs a flat steel surface for the magnets to hold properly. Many boats have stainless hardware and rails, but fiberglass and aluminum decks will not provide a magnetic surface on their own. If you plan to use it on a fiberglass or aluminum area, allow for a suitable steel mounting plate or another secure mounting approach.\u003c\/p\u003e\u003cp\u003eCheck clearance for the 16 inch length where you intend to place it so it does not interfere with lines, hatches, outriggers, antennas, or cockpit movement.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eSet the base down on a clean surface so the magnets seat fully, then route the cord so it cannot chafe or get pinched by hatches, doors, or seat bases. Leave enough slack for vibration and steering movement if used on a console area.\u003c\/p\u003e\u003cp\u003eKeep the unit and its magnets away from a magnetic compass and other sensitive instruments. A quick check before heading out can save a lot of confusion on the water.\u003c\/p\u003e\u003ch6\u003eElectrical and system integration\u003c\/h6\u003e\u003cp\u003ePower is 10 to 30 VDC, making it suitable for typical 12V and 24V onboard systems. Full-load draw is up to 6.1 A at 12 V (2.8 A at 24 V), so make sure the outlet and wiring feeding it are in good condition and protected by an appropriately rated circuit.\u003c\/p\u003e\u003cp\u003eIf you see interference on radios or electronics, increasing separation between the lightbar wiring and antenna coax, VHF wiring, or instrument harnesses often helps.\u003c\/p\u003e\u003ch6\u003eUse on board\u003c\/h6\u003e\u003cp\u003eThis setup is a good match for workboats, patrol and service craft, marina operations, and support boats that need a temporary amber warning signal during deck work, towing, or low-speed maneuvering in tight quarters. It is also handy for dockside tasks where visibility matters but you do not want a permanent install.\u003c\/p\u003e\u003cp\u003eUse it as a supplemental warning signal only, and avoid using it in a way that could be confused with required navigation lighting.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eRinse with fresh water after salt exposure and wipe down the polycarbonate dome to keep it clear. Avoid harsh solvents that can haze plastics over time.\u003c\/p\u003e\u003cp\u003ePeriodically inspect the cord, plug, and the magnet contact area for wear or grit so the unit sits flat and stays secure in vibration.\u003c\/p\u003e","brand":"Hella Marine","offers":[{"title":"Default Title","offer_id":52269035192501,"sku":"QBP513398","price":314.4,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1298666_qbp513398.jpg?v=1771541538","url":"https:\/\/www.qualityboatparts.com\/products\/qbp513398","provider":"Quality Boat Parts","version":"1.0","type":"link"}