{"product_id":"qbp506565","title":"Perko 1319 Polymer Vented Deck Fill, 1-1\/2 in Fill Hose, 5\/8 in Vent Hose, Straight Neck","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Perko 1319 is a vented straight-neck deck fill for boats using 1-1\/2 inch fill hose and 5\/8 inch vent hose. It combines the fill point and tank vent in one deck-mounted fitting, which helps keep the deck layout cleaner where space around the fuel or water fill is limited.\u003c\/p\u003e\u003cp\u003eThe polymer body is available in black or white, with a flip-top cap marked for either gas or water. The straight neck has a 2-7\/16 inch neck length, uses #10 mounting screws, and is suited to installations where the hose run can drop cleanly below the deck without the offset of an angled-neck fitting.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eVented straight-neck deck fill for 1-1\/2 inch fill hose and 5\/8 inch vent hose.\u003c\/li\u003e\n\u003cli\u003eIntegral tank vent with flame arrestor on gas-marked versions.\u003c\/li\u003e\n\u003cli\u003eFlip-top cap gives quick access without a separate deck plate key.\u003c\/li\u003e\n\u003cli\u003eNo ground wire required, which simplifies installation compared with metal fuel fills that need bonding.\u003c\/li\u003e\n\u003cli\u003eBlack or white polymer options let the fitting match common deck and cockpit finishes.\u003c\/li\u003e\n\u003cli\u003eUses #10 screws for deck mounting.\u003c\/li\u003e\n\u003cli\u003eGas-marked versions meet U.S.C.G. Safety Standards for gasoline fuel systems under 33 CFR 183, but they are not for 40 CFR 1060 subpart B emissions-compliant fuel systems.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eVariants\u003c\/h6\u003e\u003cp\u003eThis Perko 1319 deck fill is offered in gas-marked and water-marked configurations, with black and white finish options across the range.\u003c\/p\u003e\u003cp\u003eThe hose sizes, straight-neck layout, flip-top cap, polymer construction, 2-7\/16 inch neck length, and #10 screw mounting remain consistent across the listed variants. The visible deck marking and finish are the main selection points.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e1319DPGBLK: Marked for Gas, Size 4.7\/13.5. This black version suits fuel-fill locations where a dark deck fitting matches nearby hardware or trim.\u003c\/li\u003e\n\u003cli\u003e1319DPGWHT: Marked for Gas, Size 4.7\/14.1. This white version suits fuel-fill locations on lighter decks, cockpits, and transoms.\u003c\/li\u003e\n\u003cli\u003e1319DPWBLK: Marked for Water, Size 4.7\/14.0. This black version identifies the fill point for the onboard freshwater system while keeping the same vented straight-neck layout.\u003c\/li\u003e\n\u003cli\u003e1319DPWWHT: Marked for Water, Size 4.7\/13.9. This white version gives a clear water marking for freshwater fill points on light-colored deck surfaces.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and fit\u003c\/h6\u003e\u003cp\u003eCheck the deck thickness, hose routing, and space below the mounting area before fitting this deck fill. The straight-neck body works best where the fill hose and vent hose can be led downward without a sharp bend, which is important for clean filling and proper venting.\u003c\/p\u003e\u003cp\u003eUse hose that matches the 1-1\/2 inch fill connection and 5\/8 inch vent connection, and bed the flange with a sealant suitable for the deck material and the liquid system being serviced. The cap marking should face a direction that stays easy to read during fueling or filling at the dock.\u003c\/p\u003e\u003ch6\u003eUse cases on board\u003c\/h6\u003e\u003cp\u003eThis fitting is a practical match for small and mid-size boats that need a combined fill and vent on deck for gasoline or freshwater service. It is especially useful on consoles, cockpit coamings, side decks, and transom areas where a separate tank vent would add another fitting through the hull or deck.\u003c\/p\u003e\u003cp\u003eFor gasoline systems that must comply with modern evaporative-emissions requirements, confirm the full fuel-system specification before installation. This series is not intended for 40 CFR 1060 subpart B emissions-compliant applications.\u003c\/p\u003e","brand":"Perko","offers":[{"title":"Gas \/ 4.7\/13.5","offer_id":52581990990005,"sku":"QBP506565-V9","price":42.18,"currency_code":"USD","in_stock":false},{"title":"Gas \/ 4.7\/14.1","offer_id":52581991022773,"sku":"QBP506565-V10","price":0.0,"currency_code":"USD","in_stock":false},{"title":"Water \/ 4.7\/14.0","offer_id":52581991055541,"sku":"QBP506565-V11","price":0.0,"currency_code":"USD","in_stock":false},{"title":"Water \/ 4.7\/13.9","offer_id":52581991088309,"sku":"QBP506565-V12","price":0.0,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1334742_qbp506565.webp?v=1780202164","url":"https:\/\/www.qualityboatparts.com\/products\/qbp506565","provider":"Quality Boat Parts","version":"1.0","type":"link"}