{"product_id":"qbp348646","title":"Garmin Airmar P19 Plastic Thru-Hull Transducer, 8-Pin, 77\/200 kHz, 300 W, 900 ft Max Depth, Depth and Temperature, 30 ft Cable","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Garmin P19 is a plastic thru-hull mount transducer with an 8-pin connector that sends traditional sonar at 77\/200 kHz and reports depth plus water temperature. It is rated at 300 W with a maximum depth of 900 ft, and it uses a 30 ft cable for routing back to the sonar module or chartplotter.\u003c\/p\u003e\u003cp\u003eThis is a low-profile, nearly flush install that leaves about 5 mm of the housing outside the hull, which helps reduce drag while keeping a clean look below the waterline. The internal tilted element is built in, so you can match the transducer to your hull deadrise without adding a fairing block.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eTraditional dual-frequency sonar: 77\/200 kHz with 45°\/15° beamwidth\u003c\/li\u003e\n\u003cli\u003e300 W transducer power and maximum depth rating of 900 ft\u003c\/li\u003e\n\u003cli\u003eDepth and temperature sensing in one thru-hull unit\u003c\/li\u003e\n\u003cli\u003eLow-profile housing with about 5 mm extending outside the hull\u003c\/li\u003e\n\u003cli\u003eFixed-tilt element options to match common hull deadrise ranges\u003c\/li\u003e\n\u003cli\u003e8-pin connection and 30 ft attached cable for straightforward routing\u003c\/li\u003e\n\u003cli\u003eRight-angle cable exit to help in tighter bilge spaces and reduce the chance of damage when stepped on\u003c\/li\u003e\n\u003cli\u003eABYC H-27 compliant housing\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eVariants\u003c\/h6\u003e\u003cp\u003eThis product is offered in multiple tilt configurations so the transducer element can sit closer to level after installation.\u003c\/p\u003e\u003cp\u003eThe tilt angle and supported hull deadrise range vary by version. Other core specs remain consistent, including 77\/200 kHz operation, 300 W power, a 30 ft cable, and depth plus temperature reporting.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e010-10218-21: 12° tilt, intended for 8° to 15° hull deadrise. This range fits many moderate-V installations where you want the sonar beam to point straight down without adding a fairing.\u003c\/li\u003e\n\u003cli\u003e010-10218-22: 20° tilt, intended for 16° to 24° hull deadrise. This option suits deeper-V locations where deadrise at the install spot is higher and the element needs more compensation.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis is a thru-hull transducer meant for fiberglass and metal hulls. It is not intended for wood hulls. The connector is Garmin 8-pin, so the mating port needs to be an 8-pin Garmin transducer input or a compatible adapter setup.\u003c\/p\u003e\u003cp\u003eBecause tilt selection is based on the deadrise where the transducer actually mounts, measure the angle at the install location rather than relying on a general hull spec. For best readings at speed, mount in clean water flow forward of prop wash, strakes, and other turbulence sources.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eThru-hull installs require drilling the hull and sealing the housing properly. Allow room inside the bilge for the hull nut and for routing the right-angle cable exit without kinking the cable. An included rubber washer can help when tightening the nut against slightly irregular hull surfaces.\u003c\/p\u003e\u003ch6\u003eElectrical and sonar integration\u003c\/h6\u003e\u003cp\u003eThe P19 is a traditional (non-CHIRP) transducer, intended for standard sonar operation at 77\/200 kHz. It does not add ClearVü or SideVü style imaging. If your display or sounder uses a different transducer connector family, confirm the required adapter before installation.\u003c\/p\u003e\u003ch6\u003eUse on board\u003c\/h6\u003e\u003cp\u003eThis setup is a good match for boaters who want a low-profile thru-hull with depth and temperature data and who run at cruising speeds where clean-water placement matters. It also works well for sailboats that want a flush install to keep drag down around the keel area, as long as the deadrise at the install point matches the selected tilt.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eInspect the thru-hull sealing area during routine haul-outs and clean marine growth from the face to keep readings stable. Check the cable routing for chafe and keep the connector area dry and strain-relieved inside the boat.\u003c\/p\u003e","brand":"Garmin","offers":[{"title":"12°","offer_id":52270849687733,"sku":"QBP348646-V1","price":199.99,"currency_code":"USD","in_stock":true},{"title":"20°","offer_id":52270849720501,"sku":"QBP348646-V2","price":199.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1306123_qbp348646.jpg?v=1771551420","url":"https:\/\/www.qualityboatparts.com\/products\/qbp348646","provider":"Quality Boat Parts","version":"1.0","type":"link"}