{"product_id":"qbp341019","title":"Raymarine RayNet to SeaTalk HS Adapter Cable, Female to Female, 400mm","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Raymarine A80160 is a 400 mm adapter cable that links a RayNet female connection to a SeaTalk HS female connection for Raymarine marine electronics networks. It is used when an existing waterproof, locking SeaTalk HS cable needs to connect into a newer RayNet multifunction display or RayNet network device.\u003c\/p\u003e\u003cp\u003eThis short adapter is especially useful during electronics refits where older G-Series, E-Wide, C-Wide, or E-Classic MFD cable runs are already installed behind the helm. At about 15 inches long, it gives enough reach for a clean transition without adding unnecessary cable slack inside a console, electronics box, or chart table installation.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e400 mm cable length, approximately 15 inches, for close-range network transitions behind the helm or inside an electronics cabinet.\u003c\/li\u003e\n\u003cli\u003eRayNet female to SeaTalk HS female configuration for connecting legacy Raymarine SeaTalk HS cabling to newer RayNet equipment.\u003c\/li\u003e\n\u003cli\u003eSupports reuse of existing waterproof, locking SeaTalk HS cables from compatible Raymarine display networks.\u003c\/li\u003e\n\u003cli\u003eSuitable for Raymarine G-Series, E-Wide, C-Wide, and E-Classic MFD upgrade paths where the installed network cable needs to remain in place.\u003c\/li\u003e\n\u003cli\u003eHelps keep network routing tidy during refits by avoiding a full cable replacement when the existing SeaTalk HS run is still serviceable.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis adapter belongs in a Raymarine Ethernet networking layout, not in a NMEA 2000 backbone, power circuit, or transducer connection. It is intended for RayNet and SeaTalk HS network cabling, so the connector style at each end should be checked against the display, network switch, or existing installed cable before ordering.\u003c\/p\u003e\u003cp\u003eThe female-to-female layout matters. It is made for situations where the boat already has a waterproof, locking SeaTalk HS cable in place and the new equipment side uses RayNet. For many refits, that means less time pulling cable through tight helm spaces, overhead liners, or cable conduits.\u003c\/p\u003e\u003ch6\u003eInstallation and routing\u003c\/h6\u003e\u003cp\u003eInstall the adapter where it will not be strained by vibration, steering movement, hatch access, or service work around the helm. The short length is best used as a transition lead near the display or network device, with the existing SeaTalk HS cable and the RayNet equipment both supported so the connectors are not carrying cable weight.\u003c\/p\u003e\u003cp\u003eKeep the connection area dry and accessible where possible, even when using waterproof locking network cables. A little extra service loop and proper cable support can make future display removal, software service, or network troubleshooting much easier.\u003c\/p\u003e\u003ch6\u003eUse cases on board\u003c\/h6\u003e\u003cp\u003eThis cable is a good match for boat owners, installers, and refit yards updating Raymarine displays while keeping compatible SeaTalk HS cabling already run through the vessel. It is most useful on helm upgrades, flybridge refits, and navigation station work where network compatibility is the main issue rather than cable length.\u003c\/p\u003e","brand":"Raymarine","offers":[{"title":"Default Title","offer_id":52023763501237,"sku":"QBP341019","price":84.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1330934_qbp341019.webp?v=1780191970","url":"https:\/\/www.qualityboatparts.com\/products\/qbp341019","provider":"Quality Boat Parts","version":"1.0","type":"link"}