{"product_id":"qbp333852","title":"Garmin OnDeck Shore Power Sensor, For OnDeck Hub, For Cortex M1\/V1 Hubs","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Garmin OnDeck Shore Power Sensor is a shore-power status sensor that works with an OnDeck Hub so you can monitor whether dock power is present when your boat is plugged in. In the AC power plug configuration, it supports standard electrical outlets from 100 Vac to 240 Vac.\u003c\/p\u003e\u003cp\u003eIt is built for the real-world dockside problem of shore power dropping out without anyone noticing. When shore power goes away, battery chargers stop charging and dockside loads can shut down, so having clear status in your OnDeck system helps you decide what needs attention when you are away from the boat.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eWorks with an OnDeck Hub to monitor shore power status remotely.\u003c\/li\u003e\n\u003cli\u003eTwo configurations for different installs: an AC power plug style or a hard-wired style.\u003c\/li\u003e\n\u003cli\u003eAC power plug configuration supports standard electrical outlets from 100 Vac to 240 Vac.\u003c\/li\u003e\n\u003cli\u003eUseful for dockside boats where shore power supports onboard charging and other AC-dependent loads.\u003c\/li\u003e\n\u003cli\u003eLets you confirm shore power presence without relying on a quick glance at the pedestal or panel.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eVariants\u003c\/h6\u003e\u003cp\u003eThis product is offered in multiple configurations to match how your vessel brings shore power onboard.\u003c\/p\u003e\u003cp\u003eThe configuration is what changes between variants, including whether the sensor connects through an AC outlet or is wired directly into the AC supply.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e010-13009-00: Configuration: AC Power Plug. Connects through an electrical outlet, which keeps the install simple when you have a suitable receptacle tied to the boat’s shore power connection.\u003c\/li\u003e\n\u003cli\u003e010-13009-08: Configuration: Hard-wired. Connects directly into the AC supply, which suits installs where there is no appropriate outlet or where the sensor needs to live inside the electrical space.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis sensor is meant to be used as part of a Garmin OnDeck system and requires an OnDeck Hub to report shore power status. It is a fit for boats that routinely connect to dockside shore power and want visibility into whether that connection still has power.\u003c\/p\u003e\u003cp\u003eFor the plug-in configuration, the outlet used should be one that goes dead when shore power is lost so the status reflects the dock connection. For the hard-wired configuration, placement is typically within the AC electrical area where the shore power feed is accessible.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003ePlan for a mounting spot that stays dry and has some airflow, away from heat sources and areas that regularly see spray or washdowns. Secure wiring so it cannot chafe under vibration, and keep cable runs tidy so service access to panels is still practical.\u003c\/p\u003e\u003cp\u003eAny work that involves the boat’s AC supply should be done with shore power disconnected and by someone familiar with marine AC systems. After installation, confirm operation by checking the OnDeck system status with shore power present, then again after removing shore power to make sure the change is detected as expected.\u003c\/p\u003e\u003ch6\u003eUse cases on board\u003c\/h6\u003e\u003cp\u003eThis is a good match for boaters who leave the vessel at the dock and want to keep tabs on shore power status between visits. It also suits boats that run chargers, refrigeration, or humidity control while unattended and want a quick way to verify the dock connection has not dropped out.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eKeep the sensor and its connections clean and dry, and periodically inspect wiring for loosening, corrosion, or chafe. If the sensor is installed in a compartment that can get damp, routine checks are especially helpful after heavy rain, washdowns, or long periods at the dock.\u003c\/p\u003e","brand":"Garmin","offers":[{"title":"AC Power Plug","offer_id":52270818033845,"sku":"QBP333852-V1","price":59.99,"currency_code":"USD","in_stock":false},{"title":"Hard-wired","offer_id":52270818066613,"sku":"QBP333852-V2","price":59.99,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1306040_qbp333852.jpg?v=1771551224","url":"https:\/\/www.qualityboatparts.com\/products\/qbp333852","provider":"Quality Boat Parts","version":"1.0","type":"link"}