{"product_id":"qbp160839","title":"Lumishore DMX Extension Cable, For Lumishore Driver Modules, 0.2m, 7.5in","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Lumishore 010-14467-00 is a 0.2 m (7.5 in) DMX extension cable used to link Lumishore driver modules in series or add a small amount of reach in a DMX lighting run.\u003c\/p\u003e\u003cp\u003eIt is commonly used when the standard 5 m DMX cable included with 2 x EOS Light Sets does not quite reach between modules or around a bulkhead, so the connection can be made without putting the cable under tension.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e0.2 m (7.5 in) length for short extensions where a full-length cable would leave excess slack\u003c\/li\u003e\n\u003cli\u003eUsed to connect Lumishore driver modules in a series configuration\u003c\/li\u003e\n\u003cli\u003eExtends the 5 m DMX cable supplied with 2 x EOS Light Sets when a run comes up slightly short\u003c\/li\u003e\n\u003cli\u003eUseful as a jumper between nearby modules, behind liners, or inside a console where routing space is tight\u003c\/li\u003e\n\u003cli\u003eHelps keep strain off connection points by letting you maintain a sensible service loop\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis cable is intended for Lumishore DMX lighting installations that use driver modules connected in series. In setups built around the DMX cable supplied with 2 x EOS Light Sets, it fills the gap when the last few inches matter.\u003c\/p\u003e\u003cp\u003eBecause it is a short extension, it works best as a patch between modules or as a clean way to get around a bracket, corner, or pass-through without forcing the existing lead to reach.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eRoute the cable so it is not supporting its own weight at the connectors. Leave a small service loop, secure the run with cushioned clamps or tidy tie-downs, and protect it from chafe at cutouts and sharp edges.\u003c\/p\u003e\u003cp\u003eOn boats, cable runs often pass through lockers, transom spaces, and helm panels. Keep connections where they are less likely to sit in water, and avoid pinch points around hatches, sliding panels, and steering components.\u003c\/p\u003e\u003ch6\u003eUse cases on board\u003c\/h6\u003e\u003cp\u003eThis is a good match for refits and new installs where driver modules are mounted in an engine room, lazarette, under a gunwale, or behind the helm, and you need a short jumper to reach the next module without rerouting the whole run.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eAs part of routine checks, inspect the cable for chafe and make sure it has not been pinched or pulled tight as equipment shifts. If modules are removed for service, support the connectors during disconnect and reconnect so the cable is not twisted or stressed.\u003c\/p\u003e","brand":"Lumishore","offers":[{"title":"Default Title","offer_id":52256233357493,"sku":"QBP160839","price":39.19,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1284986_qbp160839.jpg?v=1771286811","url":"https:\/\/www.qualityboatparts.com\/products\/qbp160839","provider":"Quality Boat Parts","version":"1.0","type":"link"}