{"product_id":"qbp144302","title":"Lumishore ECLIPSE 4in Flush Fit LED Floodlight, White Finish, 1500 lm, IP68","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Lumishore 010-04499-00 is a 4 inch flush-fit LED flood light for above-deck work lighting, delivering 1,500 fixture lumens of white light at 5500 K.\u003c\/p\u003e\u003cp\u003eIt runs on 10.5 to 31 V DC, so it fits typical 12 V and 24 V systems, with a max draw of 1.7 A at 12 V or 0.9 A at 24 V. The housing is powder-coated aluminum with a frosted lens, and it carries an IP68 rating for wet installations and washdowns.\u003c\/p\u003e\u003cp\u003eThe beam pattern is a 70 to 90 degree oval, which spreads light across the cockpit or foredeck without creating a tight hotspot. Overall size is 12.4 x 4.5 x 4.8 cm, and the light has a 35 cm cable tail, so plan a dry splice point and proper strain relief behind the mounting surface.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e1,500 fixture lumens, 5500 K white output for clear deck and cockpit visibility\u003c\/li\u003e\n\u003cli\u003eWide 70 to 90 degree oval beam for area lighting on cabin tops, T-tops, arches, transoms, and radar pedestals\u003c\/li\u003e\n\u003cli\u003e10.5 to 31 V DC input for 12 V or 24 V boats; max current draw 1.7 A at 12 V, 0.9 A at 24 V\u003c\/li\u003e\n\u003cli\u003eFlush-mounted form factor with 12.4 x 4.5 x 4.8 cm overall dimensions\u003c\/li\u003e\n\u003cli\u003eIP68-rated light with powder-coated aluminum body and frosted lens for exposed mounting locations\u003c\/li\u003e\n\u003cli\u003eSimple two-wire power hookup for basic on and off control; dimming supported with compatible switch or lighting control modules\u003c\/li\u003e\n\u003cli\u003eBuilt-in protections including reverse polarity protection and surge protection up to 3,000 V\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eFlush mounting starts with a flat, solid surface and enough clearance behind the cutout for the back of the light and cable. Use the cutout template as a starting point, drill the corners first, then cut and file to final fit.\u003c\/p\u003e\u003cp\u003eBed the flange with a marine sealant and tighten fasteners evenly, keeping torque at or below 5 Nm so the housing and gasket seat correctly. Wipe excess sealant with soapy water.\u003c\/p\u003e\u003cp\u003eFor bracket mounting, the bracket uses an M6 fastener and a separate cable pass-through hole. Keep the cable fixed so it cannot twist, and make the cable entry watertight with an appropriate gland.\u003c\/p\u003e\u003ch6\u003eElectrical and control integration\u003c\/h6\u003e\u003cp\u003eFor basic operation, connect red to DC positive and black to ground through a properly fused circuit. The yellow lead is not used in a simple on and off setup.\u003c\/p\u003e\u003cp\u003eFor multi-light installs or control from a compatible MFD, the light can be tied into a LUX Light Control Module or an EOS-LUX Command Center; in those setups the yellow data lead is used for control and dimming.\u003c\/p\u003e\u003cp\u003eWhen using an ECLIPSE Command Center, that controller is for 12 V systems only and operates on 10 to 15 V DC, so it should not be fed from 24 V without proper conversion.\u003c\/p\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis is an above-water flood light meant for exposed mounting locations where you need broad white light without a protruding fixture. It is a good match for boats that dock and load gear at night, run offshore before sunrise, or need extra cockpit light when working lines.\u003c\/p\u003e\u003cp\u003eIf you are replacing an existing light, confirm the cutout and footprint against the 12.4 x 4.5 x 4.8 cm body and plan for the 35 cm cable tail and an accessible connection point.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eClean the lens and housing with soap and water and a soft cloth. Avoid chemical cleaners and do not power wash the fixture.\u003c\/p\u003e\u003cp\u003eInspect mounting fasteners, sealant, and cable entry points periodically, especially on boats that see heavy spray or frequent washdowns.\u003c\/p\u003e","brand":"Lumishore","offers":[{"title":"Default Title","offer_id":52256231686325,"sku":"QBP144302","price":210.07,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1284939_qbp144302.webp?v=1771286774","url":"https:\/\/www.qualityboatparts.com\/products\/qbp144302","provider":"Quality Boat Parts","version":"1.0","type":"link"}