{"product_id":"qbp143655","title":"Lumishore ECLIPSE SNL100 Neon Flex Strip Light, 12V, IP68, Blue\/White Light, 2.5m","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Lumishore 010-04496-00 is a 2.5 m ECLIPSE Neon Flex SNL100 strip light that switches between blue and white output for clean accent runs in cockpits, cabins, and under-gunwale spaces.\u003c\/p\u003e\u003cp\u003eIt runs on 12 V DC systems only (10 to 15 V DC) and carries an IP68 rating. The illuminated profile is 12.0 mm x 6.1 mm, which helps when you are tucking it behind trim or along tight radiuses.\u003c\/p\u003e\u003cp\u003eThis dual-color version uses a 3-wire hookup. With a simple switch you can toggle between blue and white, and when paired with an ECLIPSE Command Center it can also add dimming, zone control, and strobe functions.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e2.5 m (98 in) length for continuous linear accent lighting\u003c\/li\u003e\n\u003cli\u003eBlue and white output with white at 5000 K\u003c\/li\u003e\n\u003cli\u003e12 V DC only (10 to 15 V DC); max draw 0.5 A per meter (6 W per meter)\u003c\/li\u003e\n\u003cli\u003eIP68 ingress protection with fully encapsulated and potted construction for wet installs\u003c\/li\u003e\n\u003cli\u003eIlluminated cross section 12.0 mm x 6.1 mm; end caps 14.0 mm x 8.0 mm for tight clearances\u003c\/li\u003e\n\u003cli\u003eCut to length in 30 mm steps; seal cut ends before installation to keep the strip sealed\u003c\/li\u003e\n\u003cli\u003eSpot-free diffuser for a continuous line of light without visible LED points\u003c\/li\u003e\n\u003cli\u003eUV resistant and salt spray tested; suitable for indoor, outdoor, and partially covered areas\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003ePlan the run before cutting. Lay the strip out straight, offer it up to the mounting path, then cut only at the marked cut points and seal the new end before it goes on the boat.\u003c\/p\u003e\u003cp\u003eThe strip bends around curves, but it should not be twisted or bent the wrong way. Keep to a minimum bend radius of 120 mm and use extra clips around tighter curves so the light stays seated.\u003c\/p\u003e\u003cp\u003eIt can be installed in wet areas, but it is not meant to be permanently submerged.\u003c\/p\u003e\u003ch6\u003eElectrical and control\u003c\/h6\u003e\u003cp\u003eThis version uses a 3-wire connection on a 12 V DC system (10 to 15 V DC). With an on\/off\/on switch, one position selects blue and the other selects white. Do not energize both color channels at the same time.\u003c\/p\u003e\u003cp\u003eMax current draw is 0.5 A per meter (6 W per meter). For a 2.5 m strip, plan for up to about 1.25 A (15 W) when one color is active, and fuse the circuit at the power source based on the full load and wire run length.\u003c\/p\u003e\u003cp\u003eWhen tied into an ECLIPSE Command Center, color switching stays available and dimming, zoning, and strobe behavior can be controlled through the lighting system interface.\u003c\/p\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThe slim illuminated profile helps in tight mounting locations, but the end cap size matters at the cable exit. Leave room for the 14.0 mm x 8.0 mm end cap and route the cable so it is strain relieved and protected from chafe.\u003c\/p\u003e\u003cp\u003eThe housing is UV resistant, but it still benefits from being placed out of strong direct sun when possible, especially on open decks.\u003c\/p\u003e\u003ch6\u003eOn-board use\u003c\/h6\u003e\u003cp\u003eBlue light is useful when you want to preserve night vision in the cockpit, while white (5000 K) is better for seeing steps, latches, and gear. The diffuser gives a smooth line of light that works well under gunwales, along toe kicks, under seating, and around hardtop or headliner accents.\u003c\/p\u003e\u003cp\u003eThis is a good match for 12 V boats that want a low-profile linear accent light with two selectable colors, without moving to full RGB control.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eRinse salt and grime off with fresh water and a mild cleaner. Periodically check that clips are secure, the strip is not rubbing on sharp edges, and any cut ends remain fully sealed.\u003c\/p\u003e","brand":"Lumishore","offers":[{"title":"Default Title","offer_id":52256231588021,"sku":"QBP143655","price":146.99,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1284937_qbp143655.webp?v=1771286771","url":"https:\/\/www.qualityboatparts.com\/products\/qbp143655","provider":"Quality Boat Parts","version":"1.0","type":"link"}