{"product_id":"qbp117805","title":"Lumishore LUX SNL180 Neon Flex Strip Light, LUX Driver Required, CRGBW, 2000mm, IP67, Above-Water","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Lumishore 010-04427-00 is a LUX SNL180 neon flex LED strip light in a 2000 mm factory-sealed length for above-water accent and courtesy lighting on boats.\u003c\/p\u003e\u003cp\u003eIt uses a diffuser that blends the LEDs so the light reads as a continuous line instead of a row of dots, which helps when it is in direct view or reflecting off gelcoat, glass, or painted panels. The strip is rated IP67 for wet areas and washdowns, but it is not meant to be permanently submerged.\u003c\/p\u003e\u003cp\u003eThis strip uses full-spectrum CRGBW lighting with tunable white from 2700K to 6500K, 180 LEDs per meter, and a power rating of 5 W per meter. It runs on 23 to 25 V and is intended to be used with a LUX Strip Light Driver.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e2000 mm neon flex strip with a spot-free diffuser for a continuous-looking light line\u003c\/li\u003e\n\u003cli\u003eFull-spectrum CRGBW output with tunable white from 2700K to 6500K\u003c\/li\u003e\n\u003cli\u003eIP67 rating for wet areas and washdowns; for above-water applications only\u003c\/li\u003e\n\u003cli\u003e180 LEDs per meter and 5 W per meter power rating for planning loads and driver capacity\u003c\/li\u003e\n\u003cli\u003eWorks with a LUX Strip Light Driver; driver options include a voltage-stabilized 10.5 to 31 V DC input model for typical 12 V and 24 V onboard systems\u003c\/li\u003e\n\u003cli\u003eFully encapsulated and potted construction, with UV-resistant materials and salt spray testing noted\u003c\/li\u003e\n\u003cli\u003e14.5 mm x 21 mm cross section for fitting into coves, under-lips, and recesses where a rigid channel will not sit cleanly\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eWhat’s included\u003c\/h6\u003e\u003cul\u003e\u003cli\u003eOne (1) LUX SNL180 neon flex strip light, 2000 mm\u003c\/li\u003e\u003c\/ul\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003ePlan the run before you start. The strip is delivered as a pre-made, factory-sealed length to meet IP67 standards, so it is not meant to be cut. Leave room for routing at both ends, and avoid sharp corners. The minimum bend radius is 120 mm, and the strip should be side-bent only, without twisting or bending in the vertical axis.\u003c\/p\u003e\u003cp\u003eIt can be installed indoors, in partially covered areas, or outside in wet zones, but keep it out of strong direct sunlight when possible. For longer lengths, handling is easier with two people so the strip does not kink or twist while you position it.\u003c\/p\u003e\u003ch6\u003eElectrical and system integration\u003c\/h6\u003e\u003cp\u003eThis strip is intended to run through a LUX Strip Light Driver and should not be connected to third-party lighting drivers. The strip itself operates on 23 to 25 V, while driver options include a voltage-stabilized unit that accepts 10.5 to 31 V DC input from the vessel.\u003c\/p\u003e\u003cp\u003eControl can be handled with a customer-supplied momentary switch, or through compatible control hardware in the LUX ecosystem for more advanced color and scene control. Keep driver placement in mind when choosing the mounting location so wiring stays short, dry, and serviceable.\u003c\/p\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis 2000 mm strip is a good match when you want a continuous light line under gunwales, along toe-kicks, inside cockpit coamings, under T-tops, or along cabin liners where individual LED points would be distracting. If you are working in tight coves or behind trim, use the 14.5 mm x 21 mm cross section and the 120 mm minimum bend radius to confirm it will sit cleanly without stressing the strip.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eFor routine cleaning, rinse salt and grime with fresh water and wipe with a soft cloth. Avoid harsh solvents and do not use abrasion on the diffuser surface. If the strip is installed in a high-splash zone, periodically check the wiring path and mounting points so the strip stays supported and does not chafe from vibration.\u003c\/p\u003e","brand":"Lumishore","offers":[{"title":"Default Title","offer_id":52256227524789,"sku":"QBP117805","price":180.05,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1284891_qbp117805.jpg?v=1771286718","url":"https:\/\/www.qualityboatparts.com\/products\/qbp117805","provider":"Quality Boat Parts","version":"1.0","type":"link"}