{"product_id":"qbp093392","title":"Lumishore SUPRA TIX404 Thru-Hull Underwater LED Light, Dual-Color Blue\/White, 8,150 Fixture Lumens, 10.5-31V, IP68, 110 Degree Beam","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Lumishore 010-04526-00 is a dual-color (blue\/white) interchangeable thru-hull underwater LED light that runs on 10.5 to 31 V DC and puts out 8,150 fixture lumens (white) across a 110° beam.\u003c\/p\u003e\u003cp\u003eIt is IP68-rated for continuous immersion and uses a marine bronze body with a borosilicate glass lens. Plan for a 57 mm (2.25 in) hull cut-out, an 88 mm (3.47 in) outside face, and 136 mm (5.35 in) of shaft length on the inside.\u003c\/p\u003e\u003cp\u003eA 3 m (9.8 ft) pre-terminated light cable is included, so you can route the lead cleanly without splicing at the fixture.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eDual-color output: switch between blue and white at the fixture’s full rated power\u003c\/li\u003e\n\u003cli\u003e8,150 fixture lumens (white) with a 110° beam for a wide wash across the transom or hull side\u003c\/li\u003e\n\u003cli\u003e10.5 to 31 V DC input range for 12 V and 24 V electrical systems\u003c\/li\u003e\n\u003cli\u003eMaximum current draw: 6.4 A at 12 V DC, 3.2 A at 24 V DC for circuit planning\u003c\/li\u003e\n\u003cli\u003eIP68 water-ingress rating for below-the-waterline installs\u003c\/li\u003e\n\u003cli\u003eMarine bronze body with a borosilicate glass lens\u003c\/li\u003e\n\u003cli\u003eLow-profile 88 mm (3.47 in) face with an 8 mm (0.32 in) housing profile\u003c\/li\u003e\n\u003cli\u003e3 m (9.8 ft) factory-terminated cable with plug-and-play connection\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eThis is a thru-hull install that requires drilling and sealing a 57 mm (2.25 in) hole, then tightening the cartridge so the outside face sits flush on a flat section of hull. It is intended for transom or side-hull mounting rather than curved sections.\u003c\/p\u003e\u003cp\u003eTypical placement is 150 to 250 mm (6 to 10 in) below the minimum loaded waterline, with multiple lights spaced about 0.8 to 2 m (2.5 to 6.5 ft) apart for an even spread. Use a marine adhesive sealant such as 3M 4200 or equivalent, and keep retaining bolt torque under 3 Nm.\u003c\/p\u003e\u003cp\u003eDo not attempt installation or removal with the boat in the water.\u003c\/p\u003e\u003ch6\u003eElectrical and control\u003c\/h6\u003e\u003cp\u003eThe internal driver accepts 10.5 to 31 V DC for 12 V and 24 V systems. Fuse sizing is typically 10 A on 12 V installations or 5 A on 24 V installations.\u003c\/p\u003e\u003cp\u003eThe light lead is factory-terminated and should not be cut. Route the cable to a dry, protected connection point and keep all power connections waterproof with a junction box or rated connectors.\u003c\/p\u003e\u003cp\u003eIf you extend the light-to-control cable, keep total length within 6 m (20 ft) on 12 V systems or 9 m (30 ft) on 24 V systems to help avoid voltage drop and control issues.\u003c\/p\u003e\u003cp\u003eWith compatible control hardware, the light can be toggled between white and blue and can also run fade and strobe modes.\u003c\/p\u003e\u003ch6\u003eMaterials and corrosion protection\u003c\/h6\u003e\u003cp\u003eThe body is marine bronze with a borosilicate glass lens, and the unit includes a bonding connection point for galvanic protection on fiberglass and wooden hulls.\u003c\/p\u003e\u003cp\u003eFor metal or carbon fiber hulls, an isolation sleeve is required; in that case, the light should not be bonded.\u003c\/p\u003e\u003cp\u003eAvoid mounting near hot engine components or exhaust outlets, and keep exposure temperatures below 65°C (150°F).\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eInspect the locking nut and retaining bolts regularly and re-check cable attachments. A monthly inspection schedule works well on boats that stay in the water.\u003c\/p\u003e\u003cp\u003eClean the lens and face as growth builds up using a soft cloth or a soft bristled brush. Avoid abrasive pads, harsh cleaners, and pressure washing, which can scratch the lens and compromise the seal.\u003c\/p\u003e\u003ch6\u003eUse cases on board\u003c\/h6\u003e\u003cp\u003eBlue output is often used for low-glare night lighting at anchor or at the dock, while white output is helpful when you want to light up the wake or a swim platform for boarding and deck checks.\u003c\/p\u003e\u003cp\u003eThis style of light is a good match for cruisers and fishing boats that want a wide 110° spread from a flush thru-hull fitting and have access inside the hull for a proper sealed install.\u003c\/p\u003e","brand":"Lumishore","offers":[{"title":"Default Title","offer_id":52256223068341,"sku":"QBP093392","price":1600.61,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1284755_qbp093392.jpg?v=1771286658","url":"https:\/\/www.qualityboatparts.com\/products\/qbp093392","provider":"Quality Boat Parts","version":"1.0","type":"link"}