{"product_id":"qbp048384","title":"Plash Gravity Surface Mounted LED Deck Light, 6000K Cool White Light, Black Machined Aluminum Housing, 105 Lumens, 1.2W, IP67, 120 Degree Beam","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Plash Gravity is a surface mounted LED deck light for adding cool white courtesy or accent lighting to boat decks, hardtops, cockpit areas, cabins, steps, and other fiberglass mounting surfaces. This black-housing version uses a 6000K cool white LED with a 105-lumen output and a wide 120 degree beam, giving useful visibility without turning the light into a large fixture.\u003c\/p\u003e\u003cp\u003eThe Gravity light mounts on the surface, so the installation does not require coring a large hole through the mounting surface. A smaller wire pass-through and fasteners are used instead, which makes it practical for boat builders, refits, and clean lighting upgrades on finished panels.\u003c\/p\u003e\u003cp\u003eWith a machined aluminum housing, IP67 rating, 1.2W power draw, and a 9 ft tinned copper power lead with a black insulated jacket, this light is built for marine areas where washdowns, vibration, and compact mounting space matter.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eSurface mounted Gravity LED deck light with black housing and cool white 6000K light output.\u003c\/li\u003e\n\u003cli\u003e105 lumens from a 1W OSRAM LED, suitable for courtesy lighting, steps, side panels, hardtops, and deck accent locations.\u003c\/li\u003e\n\u003cli\u003e120 degree beam angle spreads light across nearby deck or panel areas instead of creating a narrow spot.\u003c\/li\u003e\n\u003cli\u003eIP67 rating supports use in exposed marine locations where spray and washdowns are common.\u003c\/li\u003e\n\u003cli\u003eLow 1.2W power draw helps keep load modest on small lighting circuits.\u003c\/li\u003e\n\u003cli\u003e12VDC and 24VDC versions are available to match common boat electrical systems.\u003c\/li\u003e\n\u003cli\u003eCurrent draw is 0.2A at 12VDC or 0.1A at 24VDC, which helps when planning circuit load and fuse protection.\u003c\/li\u003e\n\u003cli\u003e9 ft tinned copper wire lead with black insulation gives extra reach for routing behind panels or through hardtop structures.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eVariants\u003c\/h6\u003e\u003cp\u003eThis Gravity deck light range is offered with three black faceplate styles and two voltage options. The faceplate options are Eyelid, Dome, and Surface Mount, while the electrical options are 12VDC and 24VDC.\u003c\/p\u003e\u003cp\u003eAcross this black cool white configuration, the light output, color temperature, beam angle, IP67 rating, 1.2W power draw, and 9 ft tinned copper lead remain part of the same Gravity specification set. The 12V and 24V versions differ in system voltage and current draw.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eThe surface mount format is useful when a clean lighting upgrade is needed without cutting a large fixture opening. Route the wire through a small drilled pass-through, fasten the light housing to the fiberglass roof, wall, panel, step area, or deck surface, and secure the faceplate after wiring is complete.\u003c\/p\u003e\u003cp\u003eThe light should be installed where water will not sit around the fixture for long periods. As with any marine DC lighting installation, power should be isolated before wiring, connections should be protected from moisture, and the circuit should be fuse protected.\u003c\/p\u003e\u003ch6\u003eUse on board\u003c\/h6\u003e\u003cp\u003eThis light fits boats that need a low-profile cool white light for visibility around walkways, cockpit sides, storage areas, hardtop undersides, steps, or deck edges. The wide beam works well when the goal is to make nearby surfaces easier to see rather than to project light far across the boat.\u003c\/p\u003e\u003cp\u003eThe 12V versions suit many small and mid-size boat systems, while the 24V versions make sense for vessels already wired around a 24V DC lighting circuit. Matching the voltage to the boat system is the key fit check before installation.\u003c\/p\u003e","brand":"Plash","offers":[{"title":"Eyelid \/ 12V","offer_id":52713643081909,"sku":"QBP048384-V1","price":42.85,"currency_code":"USD","in_stock":true},{"title":"Eyelid \/ 24V","offer_id":52713643114677,"sku":"QBP048384-V2","price":42.85,"currency_code":"USD","in_stock":true},{"title":"Dome \/ 12V","offer_id":52713643147445,"sku":"QBP048384-V3","price":42.85,"currency_code":"USD","in_stock":true},{"title":"Dome \/ 24V","offer_id":52713643180213,"sku":"QBP048384-V4","price":42.85,"currency_code":"USD","in_stock":true},{"title":"Surface Mount \/ 12V","offer_id":52713643212981,"sku":"QBP048384-V5","price":42.85,"currency_code":"USD","in_stock":true},{"title":"Surface Mount \/ 24V","offer_id":52713643245749,"sku":"QBP048384-V6","price":42.85,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1337701_qbp048384.webp?v=1781639209","url":"https:\/\/www.qualityboatparts.com\/products\/qbp048384","provider":"Quality Boat Parts","version":"1.0","type":"link"}