{"title":"Stainless Rub Rail","description":"","products":[{"product_id":"qbp552125","title":"TACO Marine Stainless Steel Pin with Lanyard, Plastic Knob, Type 316L SS","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe TACO Marine F13-0244BN-1 is a stainless steel pin with lanyard and plastic knob for TACO ball and socket style deck hinges. It is used as replacement or service hardware on boat shade and canvas systems where the hinge needs a secure removable pin that can be handled quickly at the dock, underway, or during seasonal canvas removal.\u003c\/p\u003e\u003cp\u003eThe pin uses Type 316L stainless steel, a good match for saltwater exposure, washdowns, and the vibration that canvas and top hardware see on deck. The attached lanyard helps keep the pin with the fitting when the top is folded, adjusted, or removed, while the plastic knob gives your hand a better grip than a bare pin.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eFits TACO ball and socket style deck hinges used with canvas, shade, and top hardware.\u003c\/li\u003e\n\u003cli\u003eType 316L stainless steel construction supports use in wet, salt-exposed marine locations.\u003c\/li\u003e\n\u003cli\u003eAttached lanyard helps prevent the pin from being dropped or misplaced during adjustment.\u003c\/li\u003e\n\u003cli\u003ePlastic knob gives a hand-friendly pull point for quick removal and reinstallation.\u003c\/li\u003e\n\u003cli\u003eUseful as service hardware for bimini tops, canopies, and similar boat shade assemblies.\u003c\/li\u003e\n\u003cli\u003eBacked by a 5-year limited warranty.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and fit\u003c\/h6\u003e\u003cp\u003eThis part is intended for compatible TACO ball and socket deck hinge assemblies. Before ordering, match the hinge style on the boat to the existing TACO ball and socket hardware and check that the current pin style uses the same knob and lanyard arrangement.\u003c\/p\u003e\u003cp\u003eInstallation is straightforward once the correct hinge is confirmed. Insert the pin through the hinge connection, make sure the hardware seats fully, and keep the lanyard secured so the pin stays with the fitting when the canvas frame is opened, folded, or removed.\u003c\/p\u003e\u003ch6\u003eUse cases on board\u003c\/h6\u003e\u003cp\u003eThis pin is a practical replacement item for boats with bimini tops, cockpit shade, canvas canopies, and other removable top structures. It is especially useful where the top is adjusted often, since the knob and lanyard make day-to-day handling easier and reduce the chance of losing small hardware overboard.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eRinse the pin and nearby hinge hardware with fresh water after saltwater use, especially around the lanyard connection and moving contact points. During routine canvas checks, inspect the pin for bending, the knob for secure attachment, and the lanyard for wear so the hinge connection stays dependable over time.\u003c\/p\u003e","brand":"TACO Marine","offers":[{"title":"Default Title","offer_id":52023079370933,"sku":"QBP552125","price":20.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1331811_qbp552125.jpg?v=1780191674"},{"product_id":"qbp365274","title":"TACO Marine Rub Rail End Cap, 1-7\/8 in, 316 Stainless Steel, Polished","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe TACO Marine F16-0039 is a stainless steel rub rail end cap for finishing the end of a 1-7\/8\" rub rail installation. It gives the stern end of the rail a clean termination point while helping keep the rub rail insert seated and protected at the exposed end.\u003c\/p\u003e\u003cp\u003eThis end cap is made from Type 316L stainless steel with a polished finish, a good match for boats that see saltwater, spray, dock contact, and routine washdowns. Its listed dimensions are 2-19\/64\" long, 25\/32\" high, and 1-7\/8\" wide, and it uses a #10 screw for fastening.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eFits 1-7\/8\" rub rail applications where the end of the rail needs a finished cap\u003c\/li\u003e\n\u003cli\u003eMade from Type 316L stainless steel for corrosion resistance in marine environments\u003c\/li\u003e\n\u003cli\u003ePolished finish helps the end cap blend with stainless rub rail hardware and trim\u003c\/li\u003e\n\u003cli\u003eCaps the stern end of the rub rail and helps keep the insert from working loose\u003c\/li\u003e\n\u003cli\u003eMeasures 2-19\/64\" long, 25\/32\" high, and 1-7\/8\" wide for fit checks before installation\u003c\/li\u003e\n\u003cli\u003eUses a #10 screw, making it straightforward to match with common rub rail fastening hardware\u003c\/li\u003e\n\u003cli\u003eBacked by a five-year limited warranty\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis end cap is listed for use with several TACO rub rail profiles, including V21-1039, V21-9647, V21-9659, V21-9662, V21-9811, and V21-9866. Fit should be checked against the existing rail profile before drilling, especially on older boats where rub rail sections may have been replaced or modified over time.\u003c\/p\u003e\u003ch6\u003eInstallation and use\u003c\/h6\u003e\u003cp\u003eThe end cap is typically installed at the stern end of the rub rail after the rail and insert are seated. A dry fit before fastening helps confirm the cap sits flush, covers the cut end cleanly, and does not pinch the insert out of shape.\u003c\/p\u003e\u003cp\u003eIt is a practical finishing part for refits, collision repairs, rub rail replacement, or cosmetic cleanup where the exposed end of the rail needs protection and a neater appearance. Boat owners working on center consoles, bay boats, cruisers, and similar fiberglass hulls can use it to complete the rub rail run without leaving the insert edge open to movement or damage.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eRinse the end cap with fresh water after saltwater use and avoid harsh cleaners that can dull the polished stainless finish. During seasonal service, check that the fastener remains tight and that the rub rail insert is still seated properly behind the cap.\u003c\/p\u003e","brand":"TACO Marine","offers":[{"title":"Default Title","offer_id":52023079403701,"sku":"QBP365274","price":47.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1331596_qbp365274.jpg?v=1780191674"},{"product_id":"qbp386039","title":"TACO Marine Rub Rail End Cap, For V21-9502, 2-19\/64 in Width, SS316, Polished","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe TACO Marine F16-0091 is a polished stainless steel rub rail end cap for finishing the open end of a compatible TACO rub rail installation. It caps the rail at the end of the run, helps keep the insert seated, and gives the stern or rail termination point a clean metal finish instead of leaving the profile exposed.\u003c\/p\u003e\u003cp\u003eThis end cap measures 2-7\/8 inches long, 1-5\/32 inches high, and 2-19\/64 inches wide. It uses a #8 screw and is made from polished 316 stainless steel, a sensible choice for rub rail areas that see spray, washdowns, dock contact, and regular UV exposure.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003ePolished stainless steel finish matches bright exterior trim and rub rail hardware.\u003c\/li\u003e\n\u003cli\u003e316 stainless steel construction helps resist corrosion in saltwater and freshwater use.\u003c\/li\u003e\n\u003cli\u003eCaps the end of the rub rail so the insert stays captured instead of working loose at the termination point.\u003c\/li\u003e\n\u003cli\u003e2-19\/64 inch width supports fit checks against the rub rail profile before installation.\u003c\/li\u003e\n\u003cli\u003eCompatible with TACO V21-9502 rub rail profile.\u003c\/li\u003e\n\u003cli\u003eSold individually, which is useful when replacing one damaged end cap or completing one end of a rail run.\u003c\/li\u003e\n\u003cli\u003eBacked by a 5-year limited warranty.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and fit\u003c\/h6\u003e\u003cp\u003eFit should be checked against the existing rub rail profile before drilling or fastening, especially on older boats where rub rail styles may have been replaced during previous repairs. The listed fit is for TACO V21-9502, and the end cap is intended to sit over the rail termination and fasten with a #8 screw.\u003c\/p\u003e\u003cp\u003eFor best results, align the insert and rail before fastening the cap so the insert is fully seated and not under tension. On boats used in saltwater, bedding the fastener area and rinsing the polished stainless after heavy spray can help keep the finish looking cleaner over time.\u003c\/p\u003e\u003ch6\u003eUse on board\u003c\/h6\u003e\u003cp\u003eThis part is a good match for owners, yards, and riggers finishing a rub rail repair, replacing a missing stern end cap, or cleaning up the end of a rail run after hull work. It is a small component, but it matters because an exposed rail end can look unfinished and may allow the insert to creep out during normal docking, trailering, or washdown use.\u003c\/p\u003e","brand":"TACO Marine","offers":[{"title":"Default Title","offer_id":52023079469237,"sku":"QBP386039","price":97.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1331600_qbp386039.jpg?v=1780191674"},{"product_id":"qbp682756","title":"TACO Marine SuproFlex Small Rub Rail End Cap, For V11-9960, Type-316L SS, Mirror Polish","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe TACO Marine F16-0274 is a small stainless steel end cap for finishing a SuproFlex V11-9960 rub rail at the stern of a boat. It closes off the end of the rail run and helps keep the insert seated, giving the installation a clean termination point instead of leaving the rub rail open at the transom.\u003c\/p\u003e\u003cp\u003eThis end cap is made from Type-316L stainless steel with a mirror polish finish, so it matches the look of polished stainless rub rail hardware used on exposed deck and hull areas. It is made for #8 screw fastening and is a fit-specific accessory for the SuproFlex V11-9960 profile.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eFits TACO Marine SuproFlex V11-9960 rub rail installations.\u003c\/li\u003e\n\u003cli\u003eCaps the stern end of the rub rail for a finished appearance.\u003c\/li\u003e\n\u003cli\u003eHelps keep the rub rail insert intact at the end of the run.\u003c\/li\u003e\n\u003cli\u003eType-316L stainless steel construction suits exposed marine hardware locations.\u003c\/li\u003e\n\u003cli\u003eMirror polish finish coordinates with stainless rub rail trim.\u003c\/li\u003e\n\u003cli\u003eMade for #8 screw fastening.\u003c\/li\u003e\n\u003cli\u003eBacked by a 5-year limited warranty.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis part should be matched to the SuproFlex V11-9960 rub rail profile before ordering. It is not a universal end cap, so the rail profile matters more than the boat brand or model year.\u003c\/p\u003e\u003cp\u003eIt is commonly used where the rub rail terminates at the stern, including transom corners and aft rail ends where an open insert could shift or look unfinished. For a clean installation, dry-fit the cap against the rail end before fastening and make sure the insert is fully seated.\u003c\/p\u003e\u003ch6\u003eInstallation notes\u003c\/h6\u003e\u003cp\u003eInstall the cap after the rub rail and insert are positioned correctly. Use the correct #8 fastener for the mounting surface and avoid overtightening, since the cap needs to sit cleanly against the rail without distorting the surrounding trim.\u003c\/p\u003e\u003cp\u003eOn boats that see regular washdowns or salt exposure, rinse the stainless surface with fresh water as part of normal deck hardware care. The mirror polish finish can be maintained with the same non-abrasive cleaning approach used for other polished stainless fittings on board.\u003c\/p\u003e","brand":"TACO Marine","offers":[{"title":"Default Title","offer_id":52023079862453,"sku":"QBP682756","price":34.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1331542_qbp682756.jpg?v=1780191679"},{"product_id":"qbp149566","title":"TACO Marine 90° Top Cap, For 7\/8 in Tube, Set Screw, Polished SS316L","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe TACO Marine F11-0180S-1 is a 90 degree top cap for 7\/8 inch outside diameter tubing, used as a side-mount ball and socket fitting on boat canvas and shade hardware. It finishes the end of the tube at a right-angle connection point and uses a set screw fastener, which is useful when the fitting needs to be positioned, serviced, or adjusted without a pop-rivet installation.\u003c\/p\u003e\u003cp\u003eThis fitting belongs to TACO Marine’s ball and socket top fitting range and is made from polished Type 316L stainless steel with a Delrin insert. The pivot design allows full rotation, helps reduce rattling at the connection, and gives the frame a cleaner range of movement when used with compatible bimini, shade, or canvas support hardware.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eFits 7\/8 inch outside diameter tubing for common marine canvas and shade frame applications.\u003c\/li\u003e\n\u003cli\u003e90 degree side-mount top cap configuration for right-angle tube terminations.\u003c\/li\u003e\n\u003cli\u003eSet screw fastening allows installation without a pop-rivet on this configuration.\u003c\/li\u003e\n\u003cli\u003ePolished Type 316L stainless steel construction for exposed marine hardware locations.\u003c\/li\u003e\n\u003cli\u003eDelrin insert helps the ball and socket connection move smoothly and reduces fitting rattle.\u003c\/li\u003e\n\u003cli\u003ePatented ball and socket pivot design supports full rotation at the connection point.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and fit\u003c\/h6\u003e\u003cp\u003eUse this top cap where a 7\/8 inch tube needs a 90 degree end fitting for a canvas or shade frame. Before installation, confirm the tube outside diameter and check the mating ball and socket hardware in the existing frame so the fitting matches the rest of the system.\u003c\/p\u003e\u003cp\u003eThe set screw should be seated against clean tubing and tightened evenly. On boats exposed to vibration, trailering, or repeated folding of a bimini frame, the connection should be checked as part of normal hardware inspection.\u003c\/p\u003e\u003ch6\u003eMarine use\u003c\/h6\u003e\u003cp\u003eThe polished stainless finish makes this fitting suitable for visible topside locations where hardware appearance matters, such as bimini frames, shade supports, and canvas structures around cockpits or helm areas. It is a practical match for owners replacing a worn fitting or fabricators building a frame that needs a controlled 90 degree tube connection with a smooth pivot point.\u003c\/p\u003e","brand":"TACO Marine","offers":[{"title":"Default Title","offer_id":52023088971957,"sku":"QBP149566","price":41.99,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1331583_qbp149566.jpg?v=1780191699"},{"product_id":"qbp103279","title":"TACO Marine Side Mount Table Pedestal, Type 304 Stainless Steel, 17-3\/4 in H, 12 in W, 1-5\/8 in Tube, Polished","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe TACO Marine F16-0005A is a removable side mount table support arm for boats where a fixed table pedestal would take up too much walkway, cockpit, cabin, or deck space. It uses a 125 degree bent leg, measures 17-3\/4\" high by 12\" wide, and accepts a 1-5\/8\" tube size, giving boat owners a clear way to check fit before replacing or building out a side mount table setup.\u003c\/p\u003e\u003cp\u003eThe polished Type 304 stainless steel construction suits marine interiors and protected exterior seating areas, while the white Delrin insert helps the table support interface feel finished and reduces metal-on-metal contact at the tube connection. The removable format is useful when the table is only needed for meals, entertaining, rigging prep, or dockside use, then needs to come out of the way for movement around the boat.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eRemovable side mount table support arm for boat table pedestal systems.\u003c\/li\u003e\n\u003cli\u003e125 degree bent leg helps support a side mounted table while keeping floor space more open.\u003c\/li\u003e\n\u003cli\u003eType 304 stainless steel with a polished finish for a clean match with marine hardware and seating areas.\u003c\/li\u003e\n\u003cli\u003eWhite Delrin insert at the tube connection for a finished interface point.\u003c\/li\u003e\n\u003cli\u003e17-3\/4\" height, 12\" width, and 1-5\/8\" tube size for fit checks during replacement or installation planning.\u003c\/li\u003e\n\u003cli\u003eUseful for cockpits, cabins, pontoons, and seating areas where a removable table makes the space easier to move through.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and fit\u003c\/h6\u003e\u003cp\u003eThis support arm is meant for a side mount table pedestal arrangement, so fit should be checked against the matching table base, side mounting bracket, tube diameter, and the available swing and clearance around the seating area. The 12\" width and 125 degree leg shape matter when planning how far the table projects from the mounting point and how much passage space remains when the table is installed.\u003c\/p\u003e\u003cp\u003eBefore installation, confirm that the mounting surface is strong enough for table loads and normal movement on board. On fiberglass or cored panels, proper backing, sealant, and corrosion-aware fastener selection help keep the installation secure in a wet marine environment.\u003c\/p\u003e\u003ch6\u003eUse cases on board\u003c\/h6\u003e\u003cp\u003eThis table support is a practical match for boats that need a removable table in a compact layout, including pontoon seating zones, cockpit lounges, cabin dinettes, and deck areas used for meals or casual entertaining. It is especially useful where a permanent pedestal would interfere with foot traffic, storage access, or boarding movement.\u003c\/p\u003e\u003cp\u003eFor owners refreshing older table hardware, the confirmed 1-5\/8\" tube size and 17-3\/4\" height are the key dimensions to compare with the existing pedestal parts before ordering.\u003c\/p\u003e","brand":"TACO Marine","offers":[{"title":"Default Title","offer_id":52023120036021,"sku":"QBP103279","price":279.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1331858_qbp103279.jpg?v=1780191747"},{"product_id":"qbp640391","title":"TACO Marine Stainless Steel Hollow Back Rub Rail, 3\/4 in x 6 ft, 304 SS, Polished","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe TACO Marine S11-4511P6-1 is a 3\/4 inch wide hollow back stainless steel rub rail insert supplied in a 6 foot polished section for finishing and protecting a boat’s rub rail edge. It is made from Type 304 stainless steel and works well where the hull-to-deck joint, sheer line, or existing rub rail needs a clean metal insert that can handle normal dock contact and regular washdowns.\u003c\/p\u003e\u003cp\u003eThis insert is drilled and countersunk for #8 screws on 6 inch centers, which helps keep installation spacing consistent along straight runs and gentle curves. The hollow back profile is meant to sit over the matching rub rail base or mounting surface, giving the finished edge a bright stainless look while adding impact resistance at common contact points around slips, pilings, fenders, and trailers.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e3\/4 inch wide polished stainless steel hollow back rub rail insert for a finished metal edge on compatible boat rub rail systems.\u003c\/li\u003e\n\u003cli\u003eSupplied as a 6 foot section, making it practical for replacements, repairs, and shorter custom runs.\u003c\/li\u003e\n\u003cli\u003eType 304 stainless steel construction gives the insert the corrosion resistance expected for above-water marine trim and rub rail use.\u003c\/li\u003e\n\u003cli\u003eDrilled and countersunk for #8 screws on 6 inch centers to support a clean, even fastener layout.\u003c\/li\u003e\n\u003cli\u003ePolished finish helps match other stainless deck hardware, rails, and trim on many powerboats and center consoles.\u003c\/li\u003e\n\u003cli\u003eBacked by a 5-year limited warranty.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and fit\u003c\/h6\u003e\u003cp\u003eBefore ordering, compare the 3\/4 inch width and hollow back shape with the rub rail profile already on the boat. Stainless inserts need the correct backing profile and screw pattern to sit flat, so checking the existing rail, end caps, and corner transitions is important before cutting or drilling.\u003c\/p\u003e\u003cp\u003eFor installation, use the pre-drilled countersunk holes as the fastening guide and pair the insert with suitable #8 marine fasteners for the hull material and backing structure. On saltwater boats, bedding or sealing fastener holes is a sensible step to reduce water intrusion at the hull-to-deck joint.\u003c\/p\u003e\u003ch6\u003eUse cases on board\u003c\/h6\u003e\u003cp\u003eThis rub rail insert is a good match for boat owners and yards replacing worn stainless trim, repairing a damaged rail section, or refreshing the appearance of a rub rail without changing the full profile. It suits exposed exterior locations where a polished stainless edge is preferred over vinyl alone, especially around docking contact areas.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eRinse the insert with fresh water after saltwater use and clean it with products that are safe for polished stainless steel. Avoid abrasive pads that can scratch the finish, and inspect the fasteners periodically so the insert stays tight along the rub rail line.\u003c\/p\u003e","brand":"TACO Marine","offers":[{"title":"Default Title","offer_id":52023144251573,"sku":"QBP640391","price":79.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1331893_qbp640391.jpg?v=1780191788"},{"product_id":"qbp422881","title":"TACO Marine Flex Rub Rail Insert, For V11-9970 SuproFlex, 15\/16 in x 17\/32 in, 100 ft","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe TACO Marine Flex Chrome Insert is a 15\/16\" x 17\/32\" rub rail insert made for the V11-9970 SuproFlex rub rail. It finishes the rub rail profile with a clean insert surface while helping protect the hull-to-deck joint area from everyday contact at docks, pilings, trailers, and neighboring boats.\u003c\/p\u003e\u003cp\u003eThis insert is supplied in 100' coils, which helps on longer rub rail runs where fewer interruptions are preferred. The flexible format makes it practical for refits, replacement work, and boatyard installations where the insert needs to follow the existing rub rail shape around the boat.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e15\/16\" height and 17\/32\" width for fit with the matching TACO Marine V11-9970 SuproFlex rub rail.\u003c\/li\u003e\n\u003cli\u003e100' coil length supports continuous installation on many boat rub rail runs.\u003c\/li\u003e\n\u003cli\u003eFlexible insert format follows curved hull sections more easily than rigid lineal trim.\u003c\/li\u003e\n\u003cli\u003eFinish options cover chrome, Arctic White, and black for matching different hull and deck styling.\u003c\/li\u003e\n\u003cli\u003eMade in the USA and backed by a 5-year limited warranty.\u003c\/li\u003e\n\u003cli\u003eInstalls without tools when used with the compatible SuproFlex rub rail profile.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eVariants\u003c\/h6\u003e\u003cp\u003eThis rub rail insert is offered in three finish configurations for the same 15\/16\" x 17\/32\" profile.\u003c\/p\u003e\u003cp\u003eThe listed variants share the 100' coil length and are built around the same insert size. The main difference is the visible finish, which affects how the rub rail looks once installed on the boat.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eV12-9980CP100-1: Chrome finish. This finish gives the rub rail a polished trim look that works well when the goal is to refresh or match chrome-style exterior detailing.\u003c\/li\u003e\n\u003cli\u003eV12-9980WHA100: Arctic White finish. This finish blends naturally with many white hulls and deck edges where a more subtle insert appearance is preferred.\u003c\/li\u003e\n\u003cli\u003eV12-9980BKA100: Black finish. This finish creates a darker trim line that can suit boats with black accents, darker hull graphics, or contrast rub rail styling.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and fit\u003c\/h6\u003e\u003cp\u003eCheck the existing rub rail profile before ordering, since this insert is sized for the V11-9970 SuproFlex rub rail. The 15\/16\" x 17\/32\" dimensions matter for retention and appearance, especially on replacement jobs where an old insert has shrunk, cracked, faded, or pulled free from the rail.\u003c\/p\u003e\u003cp\u003eDuring installation, the coil format helps the insert feed along the rail around the sheer line and curved sections. For best results, the rub rail channel should be clean before the insert is pressed into place so the new trim can seat evenly.\u003c\/p\u003e\u003ch6\u003eUse cases on board\u003c\/h6\u003e\u003cp\u003eThis insert is a good match for owners, yards, and refit crews replacing worn rub rail trim on boats already using the compatible TACO Marine SuproFlex profile. It is also useful when updating the boat’s exterior finish during cosmetic restoration, especially where the rub rail remains serviceable but the insert no longer looks right.\u003c\/p\u003e","brand":"TACO Marine","offers":[{"title":"Chrome","offer_id":52581988335797,"sku":"QBP422881-V1","price":403.99,"currency_code":"USD","in_stock":true},{"title":"Arctic White","offer_id":52581988368565,"sku":"QBP422881-V2","price":0.0,"currency_code":"USD","in_stock":false},{"title":"Black","offer_id":52581988401333,"sku":"QBP422881-V3","price":0.0,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1335696_qbp422881.png?v=1780202129"}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/collections\/1119286_stainless-rub-rail.jpg?v=1763133750","url":"https:\/\/www.qualityboatparts.com\/collections\/stainless-rub-rail.oembed","provider":"Quality Boat Parts","version":"1.0","type":"link"}