{"title":"Mounting Boxes","description":"","products":[{"product_id":"qbp136614","title":"Vimar Flush-Mount Hollow Wall Mounting Box, 4-Module, 50mm Deep, Light Blue, Glow Wire 850C","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Vimar VMV71704 is a 4-module flush-mount box for hollow walls that clamps into thin panels and supports up to four modular electrical fittings. The box body measures 133.8 mm x 72.5 mm with 50 mm internal depth, and the wall cutout is prepared with a 68 mm hole cutter.\u003c\/p\u003e\u003cp\u003eIt is made from halogen-free plastic with a glow-wire rating of 850 C and an IP00 protection rating, so it belongs behind a finished plate and in protected interior locations. Break-out feed-through openings are provided around the sides and rear, with retention knockouts shaped for conduit in 16 mm, 20 mm, or 25 mm sizes and a total of 14 possible inlets.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e4-module hollow-wall box for mounting up to four electrical fittings\u003c\/li\u003e\n\u003cli\u003eMetal fins clamp securely to walls with thickness from 1 to 38 mm\u003c\/li\u003e\n\u003cli\u003eOverall size 133.8 mm x 72.5 mm with 50 mm internal depth\u003c\/li\u003e\n\u003cli\u003e68 mm hole-cutter preparation with a hole-centring plate on the back to help line up the cutout\u003c\/li\u003e\n\u003cli\u003eBreak-out cable entries and rear inlet; retention knockouts for 16 mm, 20 mm, or 25 mm conduit; 14 inlets total\u003c\/li\u003e\n\u003cli\u003eMetal fixing lugs for device support screws\u003c\/li\u003e\n\u003cli\u003eHalogen-free plastic body with glow-wire rating of 850 C; IP00 (non-sealed)\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis box is intended for hollow constructions such as plasterboard, wood, and laminate-type panels, which is common when fitting switches and sockets into interior liners, bulkheads, and furniture faces. Confirm your front-end hardware is built around Vimar 4-module frames and the matching cover plates for the finish you want.\u003c\/p\u003e\u003cp\u003eThe enclosure is not sealed and does not provide spray protection on its own, so it should be kept away from exposed cockpit and deck areas unless it sits inside a separate protected housing.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eCut the opening with a 68 mm hole saw, feed cables or conduit through the chosen break-outs, and slide the box into the panel. Tightening the clamps pulls the metal fins against the back of the wall to lock the box in place across a wide range of panel thicknesses.\u003c\/p\u003e\u003cp\u003eDevice mounting screws land on metal lugs inside the box. A matching 4-module flat cover is available for closing the opening during build-out (V71634).\u003c\/p\u003e\u003ch6\u003eUse on board\u003c\/h6\u003e\u003cp\u003eThis box fits clean electrical refits where you are adding Vimar modular switches or outlets to cabins, salons, or helm-side interior panels and want a serviceable backbox with multiple entry points. It also helps when you are routing conduit behind liners and need a box that accepts 16 mm, 20 mm, or 25 mm conduit without forcing oversized openings.\u003c\/p\u003e","brand":"Vimar","offers":[{"title":"Default Title","offer_id":52268840779957,"sku":"QBP136614","price":7.04,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1297875_qbp136614.jpg?v=1771540406"},{"product_id":"qbp185230","title":"Vimar Exé 3-Module Flush Mounting Box, For Hollow Walls, GW 960C","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Vimar VMV71793 is a 3-module flush mounting box with a plaster frame for installing Exé flush-wall cover plates on hollow walls. It uses a glow-wire tested plastic body (GW 960°C) and provides up to 58.65 mm of usable depth for wiring and device bodies behind the finished panel.\u003c\/p\u003e\u003cp\u003eOn boats this style of box is commonly used behind cabin liners, bulkhead panels, or helm and nav station surfaces where you have a cavity rather than a solid wall. The rectangular plaster frame helps the finished Exé plate sit flush, which keeps the install tidy in visible interior areas.\u003c\/p\u003e\u003cp\u003eThis box is rated IP00, so it is intended for dry, protected locations behind a finished surface, not for exposed areas that see spray or washdowns.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e3-module box for Exé flush-wall plates in hollow wall installations\u003c\/li\u003e\n\u003cli\u003eGlow-wire tested to 960°C for better resistance to heat from wiring faults\u003c\/li\u003e\n\u003cli\u003eAccepts 20 mm or 25 mm conduit; cable entry through break-out openings\u003c\/li\u003e\n\u003cli\u003eRear-entry layout with 12 inlets for routing feeds and loops in a panel cavity\u003c\/li\u003e\n\u003cli\u003eUp to 58.65 mm depth to accommodate wiring and the back of installed devices\u003c\/li\u003e\n\u003cli\u003eHalogen-free plastic body (blue) with an untreated surface finish\u003c\/li\u003e\n\u003cli\u003eCouplable format for aligned multi-gang installations\u003c\/li\u003e\n\u003cli\u003eIP00 enclosure rating, so it needs a dry, protected mounting position\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003ePlan the cut-out based on the Exé flush-wall layout, then set the plaster frame flush with the finished surface so the cover plate sits level. Leave enough cavity space behind the panel for the device depth plus room to route conductors without tight bends.\u003c\/p\u003e\u003cp\u003eConduit entries are made by knocking out the required openings and bringing in 20 mm or 25 mm tube from the rear. Switching equipment is fixed by screw mounting, which helps keep inserts stable when panels see vibration under way.\u003c\/p\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis box is sized for three Vimar modules and is intended for Exé flush-wall cover plates. If you are mixing ranges, confirm that the module format and plate system match the Exé flush-wall style before cutting the panel.\u003c\/p\u003e\u003cp\u003eThe overall footprint is 230 mm by 192 mm, which is useful for checking clearance behind trim rings, console reinforcements, and nearby hardware.\u003c\/p\u003e\u003ch6\u003eUse on board\u003c\/h6\u003e\u003cp\u003eIt fits interior switch and outlet points where you want the plate to sit flush, such as cabin bulkheads, a galley panel, or a nav station switch bank. It also works well in refits where surface boxes are being replaced with a flush-wall finish in dry living spaces.\u003c\/p\u003e\u003ch6\u003eMaintenance and checks\u003c\/h6\u003e\u003cp\u003eAfter the first few trips, re-check device fixing screws and cable supports, especially on fast powerboats where panels see more vibration. Keep the cavity dry and route conductors so they cannot chafe on cut edges or at break-out points.\u003c\/p\u003e","brand":"Vimar","offers":[{"title":"Default Title","offer_id":52268854542517,"sku":"QBP185230","price":106.95,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1298012_qbp185230.jpg?v=1771540463"},{"product_id":"qbp179696","title":"Vimar Isoset 8-Module 2x4 Surface Mount Enclosure, For Eikon and Plana Series, IP40, 23.8x8.3x5.5 cm, Plastic","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Vimar VM14814 is an IP40 surface mounting box that supports an 8-module (2+2+2+2) layout for Vimar Eikon and Plana devices.\u003c\/p\u003e\u003cp\u003eIt is a grey plastic enclosure meant for protected, dry locations on board where surface mounting makes more sense than cutting into a bulkhead or console. IP40 suits interior areas that stay out of spray and washdowns.\u003c\/p\u003e\u003cp\u003eThe box can be installed horizontally or vertically, then finished with the appropriate Eikon or Plana mechanisms and cover plate to match the 8-module format.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e8-module surface enclosure (2+2+2+2) for Vimar Eikon and Plana series devices\u003c\/li\u003e\n\u003cli\u003eIP40 protection level for sheltered interior mounting\u003c\/li\u003e\n\u003cli\u003eHorizontal or vertical installation to match your panel layout\u003c\/li\u003e\n\u003cli\u003ePlastic body with insulating construction for surface-mount switchgear and controls\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis mounting box is for installations built around the Vimar Eikon and Plana modular system, sized specifically for an 8-module arrangement. Confirm the total module count of your planned device combination so it fills the enclosure correctly.\u003c\/p\u003e\u003cp\u003eIf your existing hardware is from a different Vimar family, verify series compatibility before ordering, since cover plates and mechanisms are series-specific.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eDry-fit the enclosure on the bulkhead or console first so cable routing and device placement are clear. After the box is secured, install the mechanisms, complete wiring terminations, and finish with the matching 8-module cover plate.\u003c\/p\u003e\u003cp\u003eFor marine use, keep the mounting position away from direct weather, deck wash, and any area that routinely sees dripping gear or hose-downs.\u003c\/p\u003e\u003ch6\u003eWhere it works well on board\u003c\/h6\u003e\u003cp\u003eThis style of surface enclosure is a solid match for refits and tight-access panels where there is limited clearance behind the mounting surface. It suits cabins, nav stations, internal consoles, and other sheltered spaces where you still want a clean, serviceable control point.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eWipe with a damp cloth and mild cleaner. Avoid harsh solvents that can haze plastic, and recheck mounting screws after the first few trips if the box is installed in a spot that sees vibration.\u003c\/p\u003e","brand":"Vimar","offers":[{"title":"Default Title","offer_id":52268860899509,"sku":"QBP179696","price":14.65,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1297997_qbp179696.jpg?v=1771540487"},{"product_id":"qbp199966","title":"Vimar Isoset 2-Module Surface Enclosure, For Eikon and Plana, IP40, Grey","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Vimar VM14802 is a 2-module surface-mount enclosure for Vimar Eikon and Plana modular devices when you need a neat installation on top of a bulkhead, liner, or panel. It is rated IP40, meaning it helps keep out solid objects down to 1 mm but it does not provide water protection, so it belongs in dry interior locations. Overall size is 6.8 x 8.3 x 5.5 cm, which is handy when you are checking clearance around cabinetry, behind trims, or inside a protected console.\u003c\/p\u003e\u003cp\u003eThe housing is plastic and includes full insulating materials, which supports safe separation between the device and the mounting surface. The enclosure is finished in grey and keeps the install tidy when you are surface-mounting where a flush wall box is not practical.\u003c\/p\u003e\u003cp\u003eOn boats this style of enclosure is commonly used for switch points and small accessory outlets in cabins, at the nav station, or inside sheltered helm areas where the wiring run is surface-routed and you want a clean, enclosed termination.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e2-module surface enclosure sized for Vimar Eikon and Plana modular devices\u003c\/li\u003e\n\u003cli\u003eIP40 protection for interior spaces: protection against solid objects with no water ingress rating\u003c\/li\u003e\n\u003cli\u003eCompact external dimensions: 6.8 x 8.3 x 5.5 cm\u003c\/li\u003e\n\u003cli\u003ePlastic housing with full insulating materials for safer mounting on insulated panels\u003c\/li\u003e\n\u003cli\u003eGrey finish suited to low-visibility interior installations\u003c\/li\u003e\n\u003cli\u003eLightweight enclosure at 58.07 g\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis enclosure is intended for Vimar modular installations that use a 2-module format in the Eikon and Plana ranges. Confirm your device and support frame are the 2-module size before ordering, especially if your boat mixes different Vimar series in different areas.\u003c\/p\u003e\u003cp\u003eIf you are replacing an existing box, check both the module count and the available wall space around the faceplate. The 5.5 cm depth is the key measurement to verify when mounting over conduits, cable bundles, or structural stiffeners.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eMount the enclosure to a flat surface with fasteners appropriate for the substrate. Plan cable routing so conductors are protected from chafe and strain where they enter the box, and keep wiring runs supported to handle vibration underway.\u003c\/p\u003e\u003cp\u003eBecause this unit is IP40, avoid mounting where it will see spray, washdowns, or persistent condensation. For exposed cockpit areas, wet lockers, or open flybridge helm stations, a higher ingress-rated enclosure is the safer match.\u003c\/p\u003e\u003ch6\u003eUse cases on board\u003c\/h6\u003e\u003cp\u003eThis is a good match for refits where you are keeping Vimar Eikon or Plana devices but changing the mounting location to a surface install. It also fits cleanups where you need to relocate a switch point onto a liner or furniture face without cutting in a recess box.\u003c\/p\u003e","brand":"Vimar","offers":[{"title":"Default Title","offer_id":52268861063349,"sku":"QBP199966","price":4.37,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1298067_qbp199966.jpg?v=1771540496"},{"product_id":"qbp199971","title":"Vimar Isoset 3-Module Surface Enclosure, For Eikon \u0026 Plana, IP40","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Vimar VM14803 is a 3-module surface-mount enclosure in grey with an IP40 rating, made to house Vimar Eikon and Plana series modular devices.\u003c\/p\u003e\u003cp\u003eIt is a practical choice when you want a clean, modular finish but cannot recess a flush box into the bulkhead or panel. IP40 protection suits sheltered areas on board where it stays dry, such as inside the cabin, in a closed console, or in a protected utility space, rather than exposed decks or places that get regular washdowns.\u003c\/p\u003e\u003cp\u003eThe enclosure is plastic and uses full insulating materials, which helps when mounting on insulated walls or non-conductive panels and when keeping wiring separated inside a compact surface box.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e3-module surface enclosure for Vimar Eikon and Plana series modular devices\u003c\/li\u003e\n\u003cli\u003eIP40 protection for protected locations on board (no water ingress rating)\u003c\/li\u003e\n\u003cli\u003ePlastic housing in grey\u003c\/li\u003e\n\u003cli\u003eWith full insulating materials\u003c\/li\u003e\n\u003cli\u003eSurface-mount format for refits and for panels where a recessed box is not possible\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis enclosure follows the Vimar 3-module format and is intended to be finished with the matching 3-module accessories from the Eikon or Plana range you are installing. Confirm the series and module count of your existing plate and mounting hardware so everything lines up cleanly.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eMount the box to a flat surface and route cabling so conductors are not under tension once the modules are fitted. Allow enough slack to remove the front plate and service the devices later without pulling on terminals.\u003c\/p\u003e\u003ch6\u003eUse on board\u003c\/h6\u003e\u003cp\u003eIt works well for interior switching points, small control stations, and sheltered helm or nav areas where a surface enclosure keeps the installation tidy without cutting into structure. For cockpits, open flybridges, and other wet zones, use an enclosure with a protection rating intended for direct water exposure.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eWipe with a damp cloth and mild soap. Avoid strong solvents that can mark plastic, and periodically check around cable entries for dust or salt buildup if the box is installed in a damp compartment.\u003c\/p\u003e","brand":"Vimar","offers":[{"title":"Default Title","offer_id":52268861096117,"sku":"QBP199971","price":6.48,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1298076_qbp199971.jpg?v=1771540500"},{"product_id":"qbp200052","title":"Vimar Isoset 4-Module Surface Mounting Box, For Eikon and Plana Series, IP40, Grey, Plastic","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Vimar VM14804 is a 4-module surface-mount enclosure for installing Vimar Eikon and Plana modular devices when you cannot recess a box into the bulkhead or panel. It is rated IP40, so it belongs in protected interior locations on board where it will not see spray or washdowns.\u003c\/p\u003e\u003cp\u003eThe enclosure measures 13.6 x 8.3 x 5.5 cm and adds the space you need behind the device for terminations and cable routing. The body is plastic and includes full insulating components, which helps keep the back of the installation separated from the mounting surface.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e4-module surface enclosure sized for Vimar Eikon and Plana modular plates and mechanisms\u003c\/li\u003e\n\u003cli\u003eIP40 rating for dry, protected interior mounting areas\u003c\/li\u003e\n\u003cli\u003ePlastic enclosure with full insulating components for safer surface mounting\u003c\/li\u003e\n\u003cli\u003eGrey finish that blends with most helm and cabin panels\u003c\/li\u003e\n\u003cli\u003eOverall size: 13.6 x 8.3 x 5.5 cm\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eModule counts follow the Vimar standard. Confirm your switch, socket, or control and its cover plate are a 4-module format within the Eikon or Plana family. This is the surface enclosure only, so the mechanism and cover plate are selected separately to match your circuit and layout.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eFasten the enclosure to a flat surface, route the cable, then terminate the modular device and fit the cover plate. On boats, secure wiring so vibration does not work the terminals loose, and leave enough slack to service the connections later. If the mounting spot is likely to get damp, move the installation to a more sheltered area or use an enclosure with a higher ingress rating.\u003c\/p\u003e\u003ch6\u003eUse on board\u003c\/h6\u003e\u003cp\u003eThis enclosure works well for refits where you are adding a switch point at the nav station, bringing power to a workshop locker, or relocating controls onto a fiberglass or wood panel without cutting a recess. It also helps keep a consistent look when you are standardizing on Vimar Eikon or Plana hardware across the boat.\u003c\/p\u003e","brand":"Vimar","offers":[{"title":"Default Title","offer_id":52268861718709,"sku":"QBP200052","price":8.07,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1298083_qbp200052.jpg?v=1771540504"},{"product_id":"qbp202110","title":"Vimar Isoset IP40 1-Module Surface Enclosure, For Eikon and Plana, Grey","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Vimar VM14801 is an IP40-rated surface mounting box that accepts one module from the Vimar Eikon, Arké, and Plana ranges.\u003c\/p\u003e\u003cp\u003eIt is a practical way to add a single Vimar modular device on a bulkhead or panel when you do not have space or access for a flush mounting box. The body is grey plastic with full insulation, and the enclosure size is about 6.8 x 8.3 x 5.5 cm for planning clearances behind cabinetry, inside consoles, or on interior liners.\u003c\/p\u003e\u003cp\u003eBecause it is IP40, it belongs in dry, protected areas on board. It is not meant for exposed cockpits, washdowns, or anywhere that sees direct spray.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eSurface enclosure for one 1-module Vimar device (Eikon, Arké, Plana formats)\u003c\/li\u003e\n\u003cli\u003eIP40 protection for interior installations where water exposure is not expected\u003c\/li\u003e\n\u003cli\u003eFully insulating plastic construction to keep wiring separated from the mounting surface\u003c\/li\u003e\n\u003cli\u003eGrey finish that blends well with technical spaces and most interior panels\u003c\/li\u003e\n\u003cli\u003eCompact external dimensions: approx. 6.8 x 8.3 x 5.5 cm\u003c\/li\u003e\n\u003cli\u003eCE marked\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis is the mounting box only, meant to be used with a matching 1-module insert and cover plate from the Eikon, Arké, or Plana families. Confirm your device is the 1-module size and check that you have enough depth for terminations and bend radius for the cable behind the unit.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eMount it on a flat, rigid surface and plan cable routing so conductors are not pinched when the device is fitted. On boats, it helps to keep terminations tidy, support wiring so it cannot work loose with vibration, and leave a small service loop for future maintenance.\u003c\/p\u003e\u003ch6\u003eUse on board\u003c\/h6\u003e\u003cp\u003eThis enclosure fits refits and new builds that already standardize on Vimar modular hardware and need a clean surface-mount solution in cabins, nav stations, inside pilothouses, or within protected lockers. It is a good match when the goal is a neat single-module install without cutting into structural liners or finished joinery.\u003c\/p\u003e","brand":"Vimar","offers":[{"title":"Default Title","offer_id":52268862734517,"sku":"QBP202110","price":4.37,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1298096_qbp202110.jpg?v=1771540516"},{"product_id":"qbp202333","title":"Vimar Isoset Surface Mount Enclosure, For Eikon and Plana, 8-Module (4+4), 4x2, Vertical, IP40","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Vimar VM14832 is an IP40 surface-mount enclosure that holds up to 8 modules in a 4+4 vertical layout for Vimar Eikon and Plana mechanisms. The box measures about 136 x 140 x 54.5 mm (13.6 x 14 x 5.5 cm) and is made from plastic with full insulating materials inside.\u003c\/p\u003e\u003cp\u003eOn a boat, this style of mounting box is useful when you want a clean, finished switch or outlet cluster but do not have the depth, access, or confidence to cut a recessed opening. Because it is IP40, it belongs in dry, sheltered interior locations, not in areas that get spray, washdowns, or heavy condensation.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e8 (4+4)-module capacity in a vertical 4x2 layout\u003c\/li\u003e\n\u003cli\u003eSurface-mount enclosure for Vimar Eikon and Plana series devices\u003c\/li\u003e\n\u003cli\u003eIP40-rated housing for protected interior mounting\u003c\/li\u003e\n\u003cli\u003eOverall size about 136 x 140 x 54.5 mm (13.6 x 14 x 5.5 cm) for planning bulkhead space and clearances\u003c\/li\u003e\n\u003cli\u003ePlastic enclosure with full insulating materials inside the box\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis enclosure is built around the Vimar modular format and is intended to be paired with Eikon and Plana series mechanisms and the matching supports and cover plates for an 8-module, 4+4 vertical arrangement. If you are mixing device types (switches, dimmers, data plates, etc.), confirm the total module count and that each mechanism is compatible with the Eikon or Plana system you are using.\u003c\/p\u003e\u003cp\u003eBefore ordering, measure the mounting area on the bulkhead and check for nearby trim, door swings, grab rails, or cabinet faces. Allow extra space for cable bend radius behind the mechanisms so wiring does not get forced or pinched when the front assembly is tightened down.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eMount the box to a flat surface with corrosion-resistant fasteners suited to the substrate (fiberglass, plywood, composite panels). Where the back side of the panel is insulated or inaccessible, plan cable routing and strain relief so vibration does not work the conductors loose over time.\u003c\/p\u003e\u003cp\u003eThe enclosure itself is not voltage-specific, but the devices installed in it are. Use mechanisms, wiring, and circuit protection that match your onboard AC or DC system, and follow accepted marine wiring practice for terminations, support, and chafe protection.\u003c\/p\u003e\u003ch6\u003eUse on board\u003c\/h6\u003e\u003cp\u003eThis box is a solid fit for cabin bulkheads, a nav station, inside a helm console, or a utility area where you want an organized bank of controls without cutting a recess. It is also a practical choice for refits where you are extending an existing Vimar Eikon or Plana installation and want a consistent look.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eWipe the exterior with a soft cloth and keep the installation area as dry as practical. During routine checks, confirm the mounting fasteners stay tight and look for any signs of rubbing wires or stressed cable entries, especially in high-vibration spots.\u003c\/p\u003e","brand":"Vimar","offers":[{"title":"Default Title","offer_id":52268862865589,"sku":"QBP202333","price":14.65,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1298103_qbp202333.jpg?v=1771540519"},{"product_id":"qbp202464","title":"Vimar IP55 2-Module Surface Enclosure, For Eikon\/Arké\/Plana, Grey","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Vimar VM14902 is a 2-module surface mounting enclosure that gives you an IP55 protected location for Vimar Eikon, Arké, or Plana devices. The housing is grey plastic and measures 6.8 x 8.3 x 6.6 cm.\u003c\/p\u003e\u003cp\u003eIt is a practical choice when you need a surface box on a bulkhead or liner and you want a wiring cavity that stands up to spray and routine washdowns around the helm, in the cockpit, or in service areas.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eIP55 enclosure format to handle spray and water jets when the full assembly is installed correctly\u003c\/li\u003e\n\u003cli\u003e2-module surface box sized for Vimar Eikon, Arké, and Plana modular mechanisms\u003c\/li\u003e\n\u003cli\u003eOverall dimensions: 6.8 x 8.3 x 6.6 cm\u003c\/li\u003e\n\u003cli\u003ePlastic body with full insulating materials in the wiring space\u003c\/li\u003e\n\u003cli\u003eApprox. 94 g housing weight\u003c\/li\u003e\n\u003cli\u003eCE marked\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis is the surface enclosure body for a 2-module position. Confirm your device format and series before ordering, since module sizing and frames are specific to the Vimar range being used.\u003c\/p\u003e\u003cp\u003eDepending on the final installation, you may also need the matching front cover or plate for the protected system and the chosen switch or outlet components.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eMount the box to a flat, solid surface and keep cable runs tidy so the device can seat without forcing the wiring. If the mounting surface is thin or insulated, the insulated cavity helps keep conductors separated from the enclosure body.\u003c\/p\u003e\u003cp\u003eSeal any penetrations through the mounting surface so water cannot track into the panel. The final protection level depends on correct assembly and careful sealing around the installation.\u003c\/p\u003e\u003ch6\u003eUse on board\u003c\/h6\u003e\u003cp\u003eThis enclosure fits well on boats that are already standardized on Vimar modular hardware and need a protected surface-mount point where flush mounting is not possible. Typical locations include cockpit side panels, pilothouse bulkheads, lockers, and utility spaces that see damp air and occasional spray.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eRinse salt residue as needed and inspect the installed assembly periodically for loose fasteners, cable strain, or gaps around the mounting surface. Keeping the area clean helps the protected enclosure continue to do its job over time.\u003c\/p\u003e","brand":"Vimar","offers":[{"title":"Default Title","offer_id":52268863127733,"sku":"QBP202464","price":9.05,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1298107_qbp202464.jpg?v=1771540523"},{"product_id":"qbp202589","title":"Vimar IP55 4-Module Surface Enclosure, For Eikon\/Arké\/Plana","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Vimar VM14904 is an IP55 4-module surface mounting box used to install Vimar Eikon, Arké, or Plana devices on a bulkhead or panel when you do not have a recessed wall box. The grey plastic enclosure measures 13.6 x 8.3 x 6.6 cm, so it is straightforward to plan clearance for wiring and the finished footprint on board.\u003c\/p\u003e\u003cp\u003eThis format is commonly used for switch groups, small control stations, and protected outlets in areas that see occasional spray or washdowns. It is not meant for locations that can be submerged; keeping the seal depends on using the correct front components for the chosen series and keeping cable entries properly sealed.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eIP55 enclosure format for protected installations in damp and exposed areas on board when assembled and sealed correctly\u003c\/li\u003e\n\u003cli\u003e4-module (4M) capacity for Vimar Eikon, Arké, and Plana series mechanisms and plates\u003c\/li\u003e\n\u003cli\u003eSurface-mount layout for refits and for panels where cutting a recessed box is not practical\u003c\/li\u003e\n\u003cli\u003ePlastic housing in grey, with full insulating materials for a properly isolated installation\u003c\/li\u003e\n\u003cli\u003eOverall dimensions: 13.6 x 8.3 x 6.6 cm\u003c\/li\u003e\n\u003cli\u003eApproximate unit weight: 150 g\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis enclosure is sized for 4-module layouts within the Vimar Eikon, Arké, and Plana ranges. Match it with the correct 4M mounting frames and cover plates from the same series to maintain proper alignment and a clean seal at the front.\u003c\/p\u003e\u003ch6\u003eInstallation and sealing\u003c\/h6\u003e\u003cp\u003eMount the box to a flat, solid surface where the front plate can sit flush without rocking. Route conductors with enough slack to avoid strain on terminals, and keep bends gentle so the device sits squarely in the opening. For wet-area use, take care with cable entry points and any penetrations through the mounting surface, since those details are what typically make or break the IP55 performance in real boat installs.\u003c\/p\u003e\u003ch6\u003eUse on board\u003c\/h6\u003e\u003cp\u003eThis style of surface box is a good match for helm and cockpit switch panels under a hardtop, utility areas, and lockers that get damp air and occasional splashes. It also works well in refits where you want a protected mounting point without opening up the structure behind a liner or insulated panel.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eRinse salt residue off the outside during routine washdowns and check the front seal periodically, especially after heavy vibration or repeated access for wiring changes. If you ever remove the front plate, re-seat it carefully so the sealing surfaces stay clean and even.\u003c\/p\u003e","brand":"Vimar","offers":[{"title":"Default Title","offer_id":52268864635061,"sku":"QBP202589","price":23.4,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1298114_qbp202589.jpg?v=1771540526"},{"product_id":"qbp170514","title":"Vimar Idea\/8000 Surface Enclosure, 3-Module, IP40, RAL 7035 Grey","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Vimar VM13033 is a surface-mount IP40 enclosure for housing 3 Vimar Idea modules or 3 Vimar 8000 special modules. It comes in RAL 7035 grey and uses a plastic body with an overall size of 10 x 9.3 x 5.6 cm.\u003c\/p\u003e\u003cp\u003eThis box is meant for locations on board where you want a clean, surface-mounted installation without cutting a recess into the panel. IP40 is suited to protected interior areas and it is not a watertight enclosure, so it should be kept away from direct spray, cockpit washdowns, and exposed deck positions.\u003c\/p\u003e\u003cp\u003eIt is supplied with adaptors that support installation of 8000 standard modules, which is useful when you are mixing module types within the same Vimar ecosystem.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eSurface enclosure format for mounting on a bulkhead, liner, or interior panel when flush mounting is not practical.\u003c\/li\u003e\n\u003cli\u003e3-module capacity for Vimar Idea modules or Vimar 8000 special modules.\u003c\/li\u003e\n\u003cli\u003eIP40 protection level for protected interior spaces, with no water-jet or spray sealing.\u003c\/li\u003e\n\u003cli\u003eRAL 7035 grey finish to match common Idea and 8000 installations.\u003c\/li\u003e\n\u003cli\u003ePlastic construction that will not corrode in damp cabins and enclosed helm areas.\u003c\/li\u003e\n\u003cli\u003eSupplied with 3 adaptors (08491) for installing 8000 standard modules.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eWhat’s included\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e1 surface-mount enclosure\u003c\/li\u003e\n\u003cli\u003e3 adaptors 08491\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis enclosure is sized for a 3-module layout in the Vimar Idea system and for 3-module special devices in the 8000 range. If your installation uses 8000 standard modules, the included adaptors support that fitment. Match the module family and module count before ordering, especially when replacing an older box or mixing parts from different Vimar lines.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eMount the enclosure to a flat, solid surface where the wiring can be routed neatly and remains accessible for service. On boats, it is typically installed in the cabin, salon, enclosed pilothouse, or inside a protected console. Keep cable routing and penetrations tidy to maintain the intended IP40 protection and to avoid chafe from vibration.\u003c\/p\u003e\u003ch6\u003eUse on board\u003c\/h6\u003e\u003cp\u003eThis is a good match for refits that add or relocate cabin switches, outlets, or control modules where there is limited depth behind the panel. It also works well for new builds that want modular electrical hardware in areas that stay mostly dry and protected.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eWipe with a damp cloth and mild soap as needed. Avoid harsh solvents that can mark plastic surfaces, and check mounting tightness periodically if the installation lives in a high-vibration area.\u003c\/p\u003e","brand":"Vimar","offers":[{"title":"Default Title","offer_id":52268865159349,"sku":"QBP170514","price":8.07,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1297961_qbp170514.jpg?v=1771540529"},{"product_id":"qbp170603","title":"Vimar Idea\/8000 Surface-Mount Enclosure, 4-Module, IP40, RAL 7035 Grey","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Vimar VM13045 is an IP40 surface-mount enclosure that holds 4 Idea modules or 4 8000 special modules, finished in RAL 7035 grey.\u003c\/p\u003e\u003cp\u003eIts standard dimensions are 136 x 56 x 83 mm, and it is supplied with 4 adaptors (08491) for installing 8000 standard modules.\u003c\/p\u003e\u003cp\u003eOn a boat, it is a clean way to add a small group of Vimar modular devices on a bulkhead or inside a console when you do not want to cut in a recessed box. IP40 is for dry, protected locations, so it belongs inside the cabin, under a hardtop, or in other sheltered areas rather than places that see washdowns or direct spray.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eSurface-mount box for 4-module Vimar Idea devices or 4 Vimar 8000 special modules\u003c\/li\u003e\n\u003cli\u003eIP40 protection for sheltered mounting points where you want basic protection against contact and debris\u003c\/li\u003e\n\u003cli\u003eStandard dimensions: 136 x 56 x 83 mm for planning clearances behind the installation\u003c\/li\u003e\n\u003cli\u003eSupplied with 4 adaptors 08491 for fitting 8000 standard modules\u003c\/li\u003e\n\u003cli\u003eAdditional side and bottom knockouts to support cable entry and side-by-side installations\u003c\/li\u003e\n\u003cli\u003eCaptive cross-slotted stainless steel screws to help prevent lost hardware during wiring work\u003c\/li\u003e\n\u003cli\u003eTechnopolymer body with a bright RAL 7035 grey surface\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eWhat’s included\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eIP40 surface-mount enclosure (grey, RAL 7035)\u003c\/li\u003e\n\u003cli\u003e4 x adaptor 08491 for 8000 standard module mounting\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis enclosure is sized for Vimar Idea modular devices up to 4 modules wide and for Vimar 8000 special modules. The included adaptors allow the same box to be used with 8000 standard modules when that format is part of the installation.\u003c\/p\u003e\u003cp\u003eBecause it is surface-mounted, it is a practical option on fiberglass liners, thin panels, and refit locations where there is limited depth for a recessed box. Confirm the available space for the enclosure depth and for conductor bend radius before drilling.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eMount the enclosure to a flat surface, route conductors through the provided knockouts, and use appropriate glands or bushings so the cable jacket is protected and strain relief is handled cleanly. A drip loop on any incoming cable helps keep incidental moisture from tracking into the wiring area.\u003c\/p\u003e\u003cp\u003eThe IP40 rating assumes the installation is completed with the enclosure closed and with suitable cable or conduit entries. When the installed device has an open front, such as a socket outlet, the protection at the front of the device is lower than IP40, but it is not lower than IP20.\u003c\/p\u003e\u003ch6\u003eWhere it fits on board\u003c\/h6\u003e\u003cp\u003eThis is a good match for interior switch groups at the nav station, at a cabin entry, inside lockers, or on a protected helm console where surface mounting keeps the job simple and avoids cutting into finished panels.\u003c\/p\u003e\u003cp\u003eIf your mounting location is exposed to spray, rain, or routine washdowns, plan for a higher ingress protection enclosure rather than an IP40 box.\u003c\/p\u003e","brand":"Vimar","offers":[{"title":"Default Title","offer_id":52268865552565,"sku":"QBP170603","price":10.13,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1297965_qbp170603.jpg?v=1771540532"},{"product_id":"qbp170990","title":"Vimar Idea IP55 2-Module Surface-Mount Enclosure, For 8000 Special Modules, RAL 7035 Grey","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Vimar VM13523 is an IP55 surface-mount enclosure for two Vimar Idea modules or two 8000 special modules, used to keep modular switches and outlets protected in splash-prone areas on a boat.\u003c\/p\u003e\u003cp\u003eIt is finished in RAL 7035 grey and comes with two 08491 adaptors for fitting 8000 standard modules. The body is plastic with insulating fill, which suits mounting on insulated panels and helps avoid exposed conductive surfaces around the module area.\u003c\/p\u003e\u003cp\u003eFor fit checks, the enclosure is rated for devices up to 68 mm wide, 83 mm high, and 65 mm deep.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eIP55 protection for locations that see spray and dust, such as cockpits, flybridges, and utility areas\u003c\/li\u003e\n\u003cli\u003eSurface-mount box for adding a 2-module station without cutting a recessed mounting cavity\u003c\/li\u003e\n\u003cli\u003eCompatible with 2 Idea modules or 2 8000 special modules\u003c\/li\u003e\n\u003cli\u003eIncludes two 08491 adaptors to accept 8000 standard modules\u003c\/li\u003e\n\u003cli\u003eRAL 7035 grey housing for a clean, consistent look with common electrical enclosures on board\u003c\/li\u003e\n\u003cli\u003ePlastic enclosure with insulating fill for use on insulated bulkheads and panels\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eWhat's included\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eIP55 enclosure in RAL 7035 grey\u003c\/li\u003e\n\u003cli\u003e2 x 08491 adaptors for 8000 standard modules\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eMount on a flat, solid surface with room to access the modules and wiring. In exposed spots, route wiring with a drip loop before it enters the box and seal cable entries with appropriate glands or boots so the IP55 protection is maintained.\u003c\/p\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis enclosure is for Vimar Idea modular devices and the 8000 special module footprint. Confirm your devices are 2-module width and stay within the maximum device size so terminals and cable bends do not interfere with closing the enclosure.\u003c\/p\u003e\u003ch6\u003eUse on board\u003c\/h6\u003e\u003cp\u003eIt is commonly used for protected switch points for deck lighting, pumps, and small accessories near companionways, helm stations, wet lockers, and equipment spaces. It suits boats where electrical gear is exposed to occasional spray or washdown, rather than continuous immersion.\u003c\/p\u003e","brand":"Vimar","offers":[{"title":"Default Title","offer_id":52268866142389,"sku":"QBP170990","price":12.08,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1297969_qbp170990.jpg?v=1771540535"},{"product_id":"qbp171010","title":"Vimar Idea\/8000 3-Module IP55 Wall-Mount Enclosure, For Idea and 8000 Modules, Includes 3 Adaptors for 8000 Modules, Grey Housing","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Vimar VM13533 is an IP55 surface-mount enclosure for a 3-module Vimar Idea installation, finished in grey RAL 7035. It is used when you need a protected housing on top of a bulkhead or panel instead of cutting a recessed opening.\u003c\/p\u003e\u003cp\u003eThe enclosure accepts up to 3 Idea modules or 3 8000 special modules, and it is supplied with three 08491 adaptors for fitting 8000 standard modules. On board, it is typically used to bring switches or other modular devices into areas that see spray, dust, and day-to-day handling, while keeping the installation tidy and service-friendly.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eIP55-rated enclosure that helps keep spray and dust away from the installed modules when properly closed and mounted\u003c\/li\u003e\n\u003cli\u003eSurface-mount format for bulkheads and interior panels where a flush box is not practical\u003c\/li\u003e\n\u003cli\u003e3-module capacity for Vimar Idea devices and mixed module layouts within the Idea format\u003c\/li\u003e\n\u003cli\u003eCompatible with 3 Idea modules or 3 8000 special modules\u003c\/li\u003e\n\u003cli\u003eIncludes three 08491 adaptors for installing 8000 standard modules\u003c\/li\u003e\n\u003cli\u003eGrey RAL 7035 finish that matches common marine interior trims and panels\u003c\/li\u003e\n\u003cli\u003eInsulating plastic housing that avoids corrosion concerns common with metal boxes in damp spaces\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis enclosure is intended for the Vimar Idea module system and the 8000 module formats noted above. Before ordering, confirm that your devices and frames are from the Idea or 8000 family, since other Vimar series use different module geometry and will not seat correctly.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eMount it on a flat surface that is firm and free of deep grooves so the enclosure can close evenly. Plan cable routing so conductors are supported and not pulled tight, especially in areas that vibrate underway. If the installation includes any cable entry points, take care to seal them properly so water cannot track into the enclosure from behind the panel.\u003c\/p\u003e\u003ch6\u003eUse on board\u003c\/h6\u003e\u003cp\u003eThis enclosure makes sense for boats running Vimar Idea or 8000 modular devices that need a surface-mount point in exposed locations such as a cockpit switch position, a companionway area, or a utility locker. It is meant for splashes and washdowns, not for spaces that can flood or sit underwater.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eRinse off salt residue when needed and keep the closing surfaces clean so the enclosure can seal as intended. During routine checks, look for wire chafe inside the box and resecure any conductors that have loosened from vibration before closing it back up.\u003c\/p\u003e\u003ch6\u003eWhat's included\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eIP55 3-module surface-mount enclosure (grey RAL 7035)\u003c\/li\u003e\n\u003cli\u003e3 adaptors 08491 for 8000 standard modules\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Vimar","offers":[{"title":"Default Title","offer_id":52268866732213,"sku":"QBP171010","price":17.23,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1297973_qbp171010.jpg?v=1771540538"},{"product_id":"qbp141475","title":"Vimar Flush Mounting Box, 3-Module, IP55, Plastic, Grey","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Vimar VM13731.S is a 3-module flush mounting box, sized 126 x 102 mm with a total depth of 72 mm, built for IP55 cover installations where you want a protected device station set into a panel or bulkhead. The grey technopolymer body gives you a clean recess to route wiring and seat the device and cover assembly.\u003c\/p\u003e\u003cp\u003eOn a boat, this style of recessed box is typically used anywhere a switch, outlet, or control point needs extra protection from spray, washdowns, and dust, while keeping the finished surface easy to wipe down. It is a good fit when you are matching an existing Vimar protected station and need the correct 3-module box behind the cover.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e3-module (3M) recessed mounting box for protected IP55 cover installations\u003c\/li\u003e\n\u003cli\u003eCompatible with covers 13731.Q, 13731.Q.A, 13733.Q, and 13733.Q.A\u003c\/li\u003e\n\u003cli\u003eOverall size 126 x 102 mm with 72 mm total depth for planning cutouts and clearance behind the panel\u003c\/li\u003e\n\u003cli\u003eGrey technopolymer body suited to damp locations when installed as part of an IP55 cover assembly\u003c\/li\u003e\n\u003cli\u003eFlush mounting keeps the device station low-profile and reduces snag points in tight passages and cockpits\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis mounting box is built around a 3-module layout, so it is meant for a 3-module protected cover and matching 3-module device arrangement. If you are replacing a box behind an existing watertight cover, confirm the cover part number and the module count before cutting or ordering.\u003c\/p\u003e\u003cp\u003eThe IP55 protection level depends on the complete assembly and the way it is installed. The cover, its seal, and the wall surface all matter for keeping spray out.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003ePlan the cutout so the box sits square in the bulkhead, with enough rear clearance for the 72 mm depth plus wiring bend radius. In marine panels with core material, seal exposed core at the cut edges to help keep moisture from wicking into the laminate.\u003c\/p\u003e\u003cp\u003eRoute cables so they enter cleanly and stay strain-relieved inside the box. A simple drip loop and tidy wire routing go a long way toward keeping the inside dry and making future service easier.\u003c\/p\u003e\u003ch6\u003eUse on board\u003c\/h6\u003e\u003cp\u003eThis is a practical choice for a three-module protected station in spots like a cockpit switch bank, an exterior bulkhead near the helm, or a damp utility space where a standard interior box is more likely to see spray. It suits boats already using the Vimar protected cover system and needing a recessed box that matches that 3-module format.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eDuring routine checks, inspect the cover seal area for grit and salt buildup and clean it before it gets pressed into the sealing surface. If the station is exposed to regular washdowns, a quick rinse and wipe helps keep the cover and sealing surfaces working as intended.\u003c\/p\u003e","brand":"Vimar","offers":[{"title":"Default Title","offer_id":52268880036021,"sku":"QBP141475","price":13.11,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1297906_qbp141475.jpg?v=1771540613"},{"product_id":"qbp195737","title":"Vimar Isoset Surface Enclosure, For Eikon \u0026 Plana, 4M 2x2, IP40","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Vimar VM14812 is an IP40 surface-mount enclosure that holds a 4-module (2+2) layout for Vimar Eikon and Plana devices. It measures 13.6 x 8.3 x 5.5 cm, is made from grey plastic, and has a listed weight of 98.88 g.\u003c\/p\u003e\u003cp\u003eIt gives you a clean way to mount switches, sockets, or controls on a bulkhead or interior panel when you do not want to cut a recessed opening. The enclosure can be installed horizontally or vertically, so it is easier to match the layout of your helm, nav station, or cabin panels.\u003c\/p\u003e\u003cp\u003eIP40 covers protection from solid objects, but it does not add water sealing. On boats, it makes the most sense in dry, sheltered areas rather than exposed cockpits, open decks, or washdown zones.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e4 (2+2) module capacity for Vimar Eikon and Plana series devices\u003c\/li\u003e\n\u003cli\u003eSurface-mount format for refits and installations where flush mounting is not practical\u003c\/li\u003e\n\u003cli\u003eHorizontal or vertical mounting to suit the panel layout\u003c\/li\u003e\n\u003cli\u003eIP40 protection for interior locations where spray and washdowns are not expected\u003c\/li\u003e\n\u003cli\u003eGrey plastic enclosure that avoids corrosion concerns that can come with metal boxes in damp spaces\u003c\/li\u003e\n\u003cli\u003eFull insulating materials included for an insulated enclosure build\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis enclosure is sized for a 2x2 arrangement of two-module positions, for a total of four modules. Match the modules and front components to the Eikon or Plana family you are installing, and confirm the module count and layout before cutting or drilling your mounting surface.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eMount the box on a flat, solid surface where the wiring can be routed without tight bends or chafe points. If you are installing it on a boat, place it where it will not be hit by direct spray, and leave enough room around the enclosure to access the modules and fasteners during service.\u003c\/p\u003e\u003ch6\u003eUse on board\u003c\/h6\u003e\u003cp\u003eThis enclosure is a good fit for cruisers and workboats doing interior electrical refits, especially when adding controls at a nav station, inside a console, or along cabin bulkheads. It is also useful when you need a neat surface installation on liners or panels where a recessed cut-out would weaken the structure or expose hidden voids.\u003c\/p\u003e","brand":"Vimar","offers":[{"title":"Default Title","offer_id":52268885606581,"sku":"QBP195737","price":8.07,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1298053_qbp195737.jpg?v=1771540639"},{"product_id":"qbp397943","title":"Vimar IP55 3-Module Surface Enclosure, For Eikon Arké Plana, 3pk","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Vimar VM14903 is a 3-module surface enclosure that gives Vimar Eikon, Arké, and Plana devices a protected mounting point in areas that see spray, washdowns, or general exposure on board. The enclosure carries an IP55 rating, so it is suited to installations where you want resistance to dust ingress and water jets with the cover closed.\u003c\/p\u003e\u003cp\u003eIt is a plastic housing with an overall size of 10.2 x 8.3 x 6.6 cm and a weight of about 0.124 kg, which helps when you are planning clearances on bulkheads, console faces, and cabin partitions. The electrical rating depends on the Vimar modules installed inside, since the enclosure itself is a protective body rather than an electrical component.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e3-module surface enclosure for Vimar Eikon, Arké, and Plana wiring devices\u003c\/li\u003e\n\u003cli\u003eIP55 protection for installations that need resistance to dust ingress and water jets with the cover closed\u003c\/li\u003e\n\u003cli\u003eOverall size of 10.2 x 8.3 x 6.6 cm for practical clearance checks behind panels and in lockers\u003c\/li\u003e\n\u003cli\u003ePlastic construction with a fully insulated enclosure body\u003c\/li\u003e\n\u003cli\u003eSurface-mount format for refits where you do not want to cut in a flush box\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis enclosure is sized for 3-module Vimar devices and cover plates in the Eikon, Arké, and Plana families. If your current installation uses a different module standard or a wider multi-gang plate, confirm the module format before ordering.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eMount it on a flat, solid surface where the cover can open freely and close without interference from trim, handrails, or coamings. Bring wiring in through a properly sealed cable entry so the protection level is not compromised after installation. In wet zones, keep terminations tidy, support the cable to reduce vibration strain, and use sealed connectors where appropriate for the location.\u003c\/p\u003e\u003ch6\u003eUse on board\u003c\/h6\u003e\u003cp\u003eThis enclosure is a good match for cockpit and deck-adjacent control points, transom lockers, and other spots where a switch or socket needs extra protection from splash and washdowns. It also fits cleanly in refit work where surface mounting avoids major cutouts in thin liners or molded panels.\u003c\/p\u003e\u003ch6\u003eWhat’s included\u003c\/h6\u003e\u003cul\u003e\u003cli\u003e3 x 3-module IP55 surface enclosures\u003c\/li\u003e\u003c\/ul\u003e","brand":"Vimar","offers":[{"title":"Default Title","offer_id":52268924141749,"sku":"QBP397943","price":13.11,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1298310_qbp397943.jpg?v=1771540855"},{"product_id":"qbp396067","title":"Vimar Flush Mounting Box, For Panel Mounting Frames, 1-Module, Black, GW 960C","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Vimar VM16776.AU is a 1-module flush mounting box for panel installations where you need a clean opening and a protected cavity behind the faceplate. It is black, uses halogen-free plastic, and carries a glow wire flammability rating of 960 C with an IP40 degree of protection.\u003c\/p\u003e\u003cp\u003eThe body measures 54 x 29 mm, with depth up to 42.2 mm (36.2 mm internal depth), which helps when you are working behind helm switch panels, nav stations, and interior bulkheads where space is tight but wiring still needs room to sit naturally.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e1-module box format for panel mounting frames and one electrical fitting\u003c\/li\u003e\n\u003cli\u003eOverall size 54 x 29 mm; depth up to 42.2 mm (36.2 mm internal depth) to help confirm clearance behind the panel\u003c\/li\u003e\n\u003cli\u003eThree rear break-out cable entries with rear inlet routing\u003c\/li\u003e\n\u003cli\u003eSupports 20 or 25 mm tube size and cable up to 25 mm diameter\u003c\/li\u003e\n\u003cli\u003eIP40 protection level for protected interior installations\u003c\/li\u003e\n\u003cli\u003eHalogen-free plastic construction with glow wire flammability rating of 960 C\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eBefore cutting, check both the available depth and how your conductors will route into the back of the box. The rear entries are made for break-out feed-throughs, so you can bring wiring in cleanly and keep bends gentle rather than forcing tight turns behind the module.\u003c\/p\u003e\u003cp\u003eOn a boat, vibration and service access matter as much as the cutout. Leave enough slack to pull the device forward for inspection, and secure wiring so the terminals are not taking the load when the hull is moving.\u003c\/p\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis box is sized for a single 1-module Vimar Idea panel installation and the matching panel-mount frame. Confirm the device family you are using is the 1M format before committing to the panel opening.\u003c\/p\u003e\u003cp\u003eWith an IP40 rating, it belongs in protected locations such as the cabin, inside a console, or behind a sheltered helm panel, rather than areas exposed to direct spray or washdowns.\u003c\/p\u003e","brand":"Vimar","offers":[{"title":"Default Title","offer_id":52268952060085,"sku":"QBP396067","price":3.34,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1298281_qbp396067.jpg?v=1771541010"},{"product_id":"qbp396991","title":"Vimar Round Hollow-Wall Flush-Mount Box, 68 mm Cutout, Light Blue","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Vimar VMV71701 is a round flush-mount box in light blue for fitting Vimar modular devices into hollow wall panels on board. It installs into a 68 mm cutout and supports a two-device arrangement while keeping wiring tucked behind the wall surface.\u003c\/p\u003e\u003cp\u003eThe body measures about 71.5 mm across with about 50 mm of internal depth, and it uses metal fins to clamp onto panels from 1 to 38 mm thick. Breakout entries are set up for 16 mm, 20 mm, or 25 mm conduit, and a centring plate on the rear helps keep the hole saw lined up when you are working on cabin liners, bulkheads, or console faces.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e68 mm hole-saw cutout size for standard round hollow-wall installs\u003c\/li\u003e\n\u003cli\u003eMetal fins secure the box on wall thicknesses from 1 to 38 mm\u003c\/li\u003e\n\u003cli\u003eBreakout conduit entries for 16 mm, 20 mm, and 25 mm runs\u003c\/li\u003e\n\u003cli\u003eAbout 50 mm internal depth behind the panel for terminations\u003c\/li\u003e\n\u003cli\u003eEight entry points to route cable or conduit from the most practical direction\u003c\/li\u003e\n\u003cli\u003eMetal lugs for the support screws that hold the mounting frame\u003c\/li\u003e\n\u003cli\u003eHalogen-free plastic with a glow-wire rating of 850 C\u003c\/li\u003e\n\u003cli\u003eIP00 and not sealable, so it belongs in protected interior spaces unless the front device assembly provides the needed sealing\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eCut a clean 68 mm opening, feed wiring or conduit through the chosen knockouts, and seat the box until the front lip sits flush. Tighten the metal fins evenly so they bite behind the panel without distorting thin liners. Once the box is fixed, the mounting frame can be secured using the metal lugs, then the devices and cover plate are fitted from the front.\u003c\/p\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis box is intended for Vimar supports that mount without claw clips and rely on screw fixing instead. It is used when you need a recessed mounting point in a hollow wall and want a neat finish that keeps the device aligned and stable.\u003c\/p\u003e\u003ch6\u003eUse cases on board\u003c\/h6\u003e\u003cp\u003eIt is commonly used for interior switching and outlets in cabins, saloons, nav stations, and helm consoles where the structure is a hollow panel rather than solid timber. It also suits refits where you are standardizing on Vimar modular devices and want consistent mounting depth and cutout sizing across multiple stations.\u003c\/p\u003e","brand":"Vimar","offers":[{"title":"Default Title","offer_id":52268954976437,"sku":"QBP396991","price":6.27,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1298295_qbp396991.jpg?v=1771541037"},{"product_id":"qbp397109","title":"Vimar 3-Module Flush-Mount Box, For Eikon\/Idea\/Arke\/Plana, For Hollow Walls, Light Blue, 68 mm Cutout, Glow Wire 850C","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Vimar VMV71703 is a 3-module flush-mount box for hollow walls, used when you need to mount Vimar modular switches or outlets in a thin interior panel on a boat.\u003c\/p\u003e\u003cp\u003eIt installs in a 68 mm cut-out and uses metal fins to clamp securely to wall thicknesses from 1 to 38 mm. Improved retention knockouts accept conduit runs in 16, 20, or 25 mm sizes, and a centring plate on the back helps keep the hole layout aligned when you are working on finished liners or cabinetry panels.\u003c\/p\u003e\u003cp\u003eThe body is halogen-free plastic with a GW 850 °C glow-wire rating. It is not a sealed enclosure (IP00), so it belongs in protected areas behind a finished plate or inside interiors rather than in places that see direct spray or washdowns.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e3-module box for hollow-wall installations, in light blue\u003c\/li\u003e\n\u003cli\u003e68 mm hole-saw cut-out with a built-in centring plate for cleaner alignment\u003c\/li\u003e\n\u003cli\u003eMetal fins clamp to panel thicknesses from 1 to 38 mm\u003c\/li\u003e\n\u003cli\u003eRetention knockouts for conduit sizes 16, 20, or 25 mm\u003c\/li\u003e\n\u003cli\u003eHalogen-free plastic body with GW 850 °C glow-wire rating\u003c\/li\u003e\n\u003cli\u003eIP00 rating, intended for dry, protected mounting locations\u003c\/li\u003e\n\u003cli\u003eCan be coupled for side-by-side installations when building multi-gang runs\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis box is sized for Vimar 3-module mounting frames commonly used with Vimar modular device ranges such as Idea, Eikon, Eikon-Evo, and Arke. The rectangular body sits behind the finished plate, while the 68 mm cut-out and clamping fins handle the mechanical hold in hollow panels.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eMark the cut-out, drill with a 68 mm hole saw, and clean up the edge so the box seats flat. Feed your wiring or conduit through the appropriate knockouts, insert the box, and tighten the fins until it is firm without crushing the panel. Once the mounting frame and devices are in place, give the assembly a final check for movement before fitting the cover plate.\u003c\/p\u003e\u003ch6\u003eUse cases on board\u003c\/h6\u003e\u003cp\u003eThis is a good match for refits and new builds where you are adding Vimar controls to cabin bulkheads, liners, nav stations, galleys, and other interior panels that are too thin for solid-wall boxes. If the location sees moisture, plan protection at the faceplate level and keep the box itself out of direct spray.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eAfter the first few trips, re-check the clamping fins and device screws for tightness, especially on boats that see vibration and pounding. If you open the plate later for service, inspect the cable entries and knockouts to make sure wiring stays supported and not pinched.\u003c\/p\u003e","brand":"Vimar","offers":[{"title":"Default Title","offer_id":52268956287157,"sku":"QBP397109","price":4.73,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1298300_qbp397109.jpg?v=1771541052"},{"product_id":"qbp397275","title":"Vimar Hollow-Wall Flush-Mount Box, 6\/7-Module, 68 mm Cutout, GW 850°C","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Vimar VMV71706 is a 6 to 7-module flush-mount box for hollow walls, sized to hold up to 7 modular electrical devices behind a finished panel.\u003c\/p\u003e\u003cp\u003eThe cutout pattern is laid out around a 68 mm hole saw, which helps get a clean opening in materials like plasterboard and similar thin panels. With a 50 mm internal depth and an overall footprint of 193 mm by 72.5 mm, it gives you workable space for wiring while staying tidy behind liners and console panels.\u003c\/p\u003e\u003cp\u003eIt uses halogen-free plastic and carries a glow-wire rating of 850 °C. The box is rated IP00, so it belongs in dry, protected locations rather than anywhere that sees spray or washdowns.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e6 to 7-module in-line box for hollow walls, supports up to 7 device positions\u003c\/li\u003e\n\u003cli\u003eHole preparation uses a 68 mm hole saw, with a centring plate on the back to help line things up\u003c\/li\u003e\n\u003cli\u003eMetal fins clamp to panel thicknesses from 1 to 38 mm for a firm hold in liners and bulkheads\u003c\/li\u003e\n\u003cli\u003eBreak-out openings for conduit or sleeving in 16, 20, or 25 mm sizes, with 18 entry points total\u003c\/li\u003e\n\u003cli\u003eMetal screw lugs for mounting device supports by screwing\u003c\/li\u003e\n\u003cli\u003eHalogen-free plastic body with glow-wire rating 850 °C; IP00 for dry, protected installations\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eMark the hole pattern using the rear centring plate, drill with a 68 mm hole saw, then finish the opening so the box sits flat against the panel surface.\u003c\/p\u003e\u003cp\u003eBring wiring or conduit in through the break-outs, position the box, and tighten the metal fins until the box is secure. Plan for service access by leaving enough slack inside the 50 mm cavity to remove devices later without pulling on the conductors.\u003c\/p\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis box is intended for installations that use a 6 to 7-module in-line support that screws to the box. Confirm the device support and faceplate you plan to use are sized for up to 7 modules and match the fixing points.\u003c\/p\u003e\u003cp\u003eBecause it is a hollow-wall box, it works best where there is a void behind the surface, such as cabin liners, furniture panels, and lightweight bulkheads.\u003c\/p\u003e\u003ch6\u003eUse cases on board\u003c\/h6\u003e\u003cp\u003eCommon onboard locations include cabin bulkheads, nav stations, galley panels, and helm consoles where you want a flush bank of switches or outlets without adding a surface box.\u003c\/p\u003e\u003cp\u003eIt is a good match for refits and new builds that route wiring in conduit behind interior liners. For damp areas, keep the installation behind a sealed front assembly and away from direct spray, since the box itself is IP00.\u003c\/p\u003e","brand":"Vimar","offers":[{"title":"Default Title","offer_id":52268960383157,"sku":"QBP397275","price":11.83,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1298305_qbp397275.jpg?v=1771541069"},{"product_id":"qbp880608","title":"Vimar 8000 IP40 2-Module Surface Enclosure, RAL 7035 Ivory","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Vimar VM13022.A is an IP40 surface enclosure for mounting two 8000 Series standard modules on a bulkhead, panel, or cabinet face when you cannot recess a box behind the surface. It comes in an ivory finish (RAL 7035) and keeps the installation compact, with overall dimensions around 6.8 x 9.3 x 5.6 cm.\u003c\/p\u003e\u003cp\u003eIP40 means it helps keep fingers and larger debris out of the wiring space (solid objects larger than 1 mm), but it is not sealed against water. On a boat, it suits dry interior locations like cabins, nav stations, and enclosed helm areas rather than spots that see spray, washdowns, or heavy condensation.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eSurface enclosure sized for two 8000 Series standard modules (2-module format).\u003c\/li\u003e\n\u003cli\u003eIP40 rating for basic protection from solid objects, with no water ingress protection.\u003c\/li\u003e\n\u003cli\u003eIvory finish in RAL 7035 for a consistent look with matching modular components.\u003c\/li\u003e\n\u003cli\u003eOverall dimensions around 6.8 x 9.3 x 5.6 cm to fit cleanly on bulkheads and cabinetry.\u003c\/li\u003e\n\u003cli\u003ePlastic, insulating enclosure body for non-metallic mounting in mixed onboard environments.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis enclosure is intended for installations using two 8000 Series standard modules. Before ordering, confirm your devices are the standard 8000 module format and that the planned mounting surface has enough flat area for the enclosure footprint and enough clearance for cable bend radius behind the module space.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eMount the enclosure to a solid, flat surface and route conductors so they are supported and protected from chafe. After the enclosure is fixed in place, fit the compatible modular hardware and devices for your 2-module layout, then finish with the matching front components used in your 8000 system.\u003c\/p\u003e\u003ch6\u003eUse on board\u003c\/h6\u003e\u003cp\u003eThis style of surface enclosure is a practical choice for refits and for fiberglass or composite interiors where cutting a recessed opening is not desired. It is commonly used for mounting switches, outlets, or control modules on cabin bulkheads, inside lockers, and at nav or helm stations that stay dry.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eWipe the enclosure with a damp cloth and mild soap, and avoid harsh solvents that can dull plastics. As part of routine onboard checks, confirm the enclosure remains firmly fastened and that wiring inside stays tidy and strain-relieved to handle vibration.\u003c\/p\u003e","brand":"Vimar","offers":[{"title":"Default Title","offer_id":52269529301173,"sku":"QBP880608","price":5.45,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1300372_qbp880608.jpg?v=1771544449"},{"product_id":"qbp880657","title":"Vimar IDEA\/8000 Surface-Mount Enclosure, IP55, 1 Module, Grey","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Vimar VM13521 is an IP55 surface-mount enclosure sized for one 8000 standard module, finished in RAL 7035 grey.\u003c\/p\u003e\u003cp\u003eIt is used when you need to mount a single Vimar 8000 Series control on a bulkhead or panel and keep it protected in areas that see spray, dust, and routine wipe-downs. The insulating plastic body keeps the enclosure from corroding and helps avoid unwanted contact with live parts when installed correctly.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eIP55-rated enclosure to help protect a single module installation from dust and water jets\u003c\/li\u003e\n\u003cli\u003eSurface-mount format for one Vimar 8000 standard module\u003c\/li\u003e\n\u003cli\u003eRAL 7035 grey finish for a clean match with other 8000 Series hardware\u003c\/li\u003e\n\u003cli\u003ePlastic construction with insulating properties for marine and industrial mounting locations\u003c\/li\u003e\n\u003cli\u003eCompact footprint that works well for retrofits when you cannot recess a box into the structure\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis enclosure is built around the 8000 standard module format in a 1-module size. Before ordering, confirm the module style on your boat is 8000 standard and that your chosen mechanism and front hardware are intended for the same system.\u003c\/p\u003e\u003cp\u003eIf you are replacing an older surface box, check the available footprint on the mounting surface and plan cable routing so conductors are not forced into tight bends behind the module.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eMount it on a flat, rigid surface where the cover can open fully and the wiring can enter cleanly. On boats, that usually means a helm side panel, cockpit coaming, companionway bulkhead, or a sheltered area near deck equipment where a surface box is easier than cutting in a recess.\u003c\/p\u003e\u003cp\u003eFor wet areas, take the time to seal the cable entry and fasteners so water cannot track behind the enclosure. Leave a small drip loop in the cable run when possible so moisture does not run straight into the back of the box.\u003c\/p\u003e\u003ch6\u003eUse cases on board\u003c\/h6\u003e\u003cp\u003eThis is a good match for boats already using Vimar 8000 Series modules and needing a small, splash-resistant surface enclosure for a single control point. It is commonly used for one-off additions like a switch near a transom door, a control by the cockpit table, or a utility point in a sheltered locker.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eRinse salt residue off with fresh water and wipe the enclosure down during routine cleaning. If the box is installed in a high-traffic spot, check occasionally that the cover closes properly and that the mounting screws stay snug after vibration and temperature changes.\u003c\/p\u003e","brand":"Vimar","offers":[{"title":"Default Title","offer_id":52269529497781,"sku":"QBP880657","price":12.08,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1300376_qbp880657.jpg?v=1771544451"},{"product_id":"qbp881190","title":"Vimar 8000 Series 2-Module Surface Enclosure, IP55, RAL 7035 Grey","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Vimar VM13522 is an IP55 surface-mount enclosure for two Vimar 8000 Series standard modules in RAL 7035 grey. It is used to house compatible wiring devices where you want extra protection against spray and dust.\u003c\/p\u003e\u003cp\u003eBecause it mounts on the surface, it works well on bulkheads, consoles, and liners where there is no space for a recessed box. It also helps keep the installation more contained in areas that see frequent cleaning or occasional splashes.\u003c\/p\u003e\u003cp\u003eThe housing is non-metallic and insulating, which is useful around terminals and onboard wiring. IP protection depends on correct mounting and properly sealed cable entries for your specific location.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eIP55-rated enclosure for installs exposed to spray, washdowns, and airborne dust when correctly sealed\u003c\/li\u003e\n\u003cli\u003e2-module capacity for Vimar 8000 Series standard modules\u003c\/li\u003e\n\u003cli\u003eSurface-mount format for bulkheads, consoles, and cabin panels without a recessed mounting box\u003c\/li\u003e\n\u003cli\u003eNon-metallic, insulating housing suited to marine electrical fit-outs\u003c\/li\u003e\n\u003cli\u003eRAL 7035 grey finish\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eMount the enclosure on a flat, stable surface so the sealing areas sit evenly. In high-vibration spots, back up thin panels and use fasteners that will not loosen over time.\u003c\/p\u003e\u003cp\u003eMaintain the IP55 protection by using cable glands or grommets matched to the cable diameter and by sealing any fastener penetrations as needed for the mounting surface. Form drip loops on incoming cables so water does not track toward the enclosure.\u003c\/p\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis enclosure is sized for two Vimar 8000 Series standard modules. Confirm that the devices you are fitting are the 8000 module format and that your faceplate and accessories are intended for protected, surface-mounted installations.\u003c\/p\u003e\u003cp\u003eIf your system uses a different Vimar family or a specialty module format, verify module size and the correct enclosure style before ordering.\u003c\/p\u003e\u003ch6\u003eUse on board\u003c\/h6\u003e\u003cp\u003eThis style of enclosure is typically used for switches and outlets mounted in cockpits, flybridges, deck access areas, and utility spaces where a surface box is preferred over a flush-mount back box. It is also useful for refits where you want added protection without cutting into finished panels.\u003c\/p\u003e\u003cp\u003eThis product is a good match for boats already using Vimar 8000 Series devices and needing a 2-module, surface-mounted enclosure for wet or dusty zones.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eRinse salt residue off the exterior when practical and avoid aggressive solvents that can haze plastics. Periodically check that mounting screws stay tight and that any cable glands remain snug, especially after service work in the area.\u003c\/p\u003e","brand":"Vimar","offers":[{"title":"Default Title","offer_id":52269529694389,"sku":"QBP881190","price":10.45,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1300377_qbp881190.jpg?v=1771544452"},{"product_id":"qbp884459","title":"Vimar Plana 4-Module Table Mounting Box, Matt White Finish, Halogen-Free Plastic, IP20, Cable Entry, 142.5 x 80 x 67.6 mm","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Vimar VM14784 is a 4-module table mounting box in white for building a clean, surface-mounted switch or outlet point on board where a flush box is not practical. It mounts horizontally and is sized at 142.50 mm wide, 80.00 mm high, and 67.60 mm deep, which helps when you are checking clearance on a nav table, helm side panel, or bulkhead.\u003c\/p\u003e\u003cp\u003eThis enclosure is rated IP20, so it belongs in dry interior areas where it will not see spray or washdowns. The housing is plastic and halogen-free with a matt finish in RAL 9003 (white), and it includes a cable entry opening for bringing conductors in from behind or from a routed cable path.\u003c\/p\u003e\u003cp\u003eIt is supplied as the box only and is meant to be completed with the matching mounting frame and cover plate for a 4-module setup.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e4-module table mounting box for horizontal installations\u003c\/li\u003e\n\u003cli\u003eIP20 protection level for dry interior locations\u003c\/li\u003e\n\u003cli\u003eHalogen-free plastic housing with a matt white finish (RAL 9003)\u003c\/li\u003e\n\u003cli\u003eCable entry opening for straightforward wire routing into the enclosure\u003c\/li\u003e\n\u003cli\u003eOverall size: 142.50 mm (W) x 80.00 mm (H) x 67.60 mm (D)\u003c\/li\u003e\n\u003cli\u003eSupplied as the box only and completed with a compatible mounting frame and cover plate\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis box is intended for a 4-module arrangement using Vimar modular switching components and the matching frame and plate. If you are replacing an existing installation, confirm the module count and series so the frame and cover plate match the devices you are fitting.\u003c\/p\u003e\u003cp\u003eUse the overall dimensions to check that the enclosure will not interfere with drawers, lids, throttle panels, or chart table hinges. The 67.60 mm depth is also worth checking if you need room for wire bends behind the devices.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eMount the box on a stable, flat surface and route wiring so it is protected from chafe and vibration. Where conductors pass through the cable entry, add strain relief and edge protection so movement over time does not damage insulation.\u003c\/p\u003e\u003cp\u003eSince IP20 is intended for indoor use, place it where it stays dry and away from direct exposure to salt spray. If the mounting surface is part of an exterior structure, seal fastener holes appropriately to prevent moisture from tracking into the panel core.\u003c\/p\u003e\u003ch6\u003eUse on board\u003c\/h6\u003e\u003cp\u003eThis style of table box makes sense for refits and new installations where you want a neat control point at a nav station, inside a protected helm area, or on an interior bulkhead without cutting a large recess for a flush box.\u003c\/p\u003e\u003cp\u003eIt is a good match for boats that need tidy cable management and a finished look for modular switches, outlets, or controls in interior living and working spaces.\u003c\/p\u003e","brand":"Vimar","offers":[{"title":"Default Title","offer_id":52269540081845,"sku":"QBP884459","price":49.62,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1300451_qbp884459.jpg?v=1771544499"},{"product_id":"qbp884877","title":"Vimar Isoset IP40 16-Module Surface Enclosure, For Eikon Arké and Plana, 4+4+4+4 Horizontal, Grey","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Vimar VM14839 is a 16-module (4+4+4+4) surface-mount enclosure for Vimar Eikon and Plana series devices, arranged in a 4x4 horizontal layout with an IP40 protection rating.\u003c\/p\u003e\u003cp\u003eIt is meant for clean, accessible installations where a flush box is not practical, such as on finished bulkheads, inside consoles, or in refit work where you cannot cut depth into fiberglass. IP40 helps protect against fingers and solid objects larger than 1 mm, but it is not sealed against water, so it is best kept in sheltered, dry onboard locations.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e16-module capacity in a 4+4+4+4 configuration for building out larger control or outlet groups\u003c\/li\u003e\n\u003cli\u003eSurface-mount format for installations where there is limited cavity depth behind the mounting surface\u003c\/li\u003e\n\u003cli\u003eIP40 protection level for interior spaces where splash and washdown exposure is not expected\u003c\/li\u003e\n\u003cli\u003eBuilt for Vimar Eikon and Plana series device layouts in a horizontal 4x4 format\u003c\/li\u003e\n\u003cli\u003eInsulating enclosure body for a fully non-conductive housing around the device grid\u003c\/li\u003e\n\u003cli\u003eHorizontal orientation keeps multi-point switching and labeling in one continuous bank\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis enclosure is sized for a 16-module (4x4) horizontal arrangement. Before ordering, confirm that your planned combination of Vimar Eikon or Plana modules and frames matches the 4+4+4+4 layout and that the finished mounting location has enough flat area for the full enclosure footprint.\u003c\/p\u003e\u003cp\u003eThis is the enclosure only. Switch mechanisms, sockets, modules, frames, and cover plates are selected separately to match your onboard circuits and the look of the surrounding panel.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eMount the box to a solid, flat surface and route wiring so it is supported and strain-relieved before it enters the enclosure. On a boat, simple details matter: keep cable runs tidy, maintain a drip loop where wiring could see condensation, and avoid mounting positions where water can sit against the enclosure.\u003c\/p\u003e\u003cp\u003eUse correct overcurrent protection for the circuits feeding the devices installed in the enclosure, and follow common marine wiring practices for conductor sizing, terminations, and chafe protection.\u003c\/p\u003e\u003ch6\u003eUse on board\u003c\/h6\u003e\u003cp\u003eThis type of surface enclosure is a good match for cabins, nav stations, enclosed helm consoles, and other interior areas where you want easy access to switching or outlets without cutting into the structure. It also works well when adding a new bank of controls during refits and upgrades.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eFor routine cleaning, wipe with a lightly damp cloth and avoid harsh solvents that can dull plastics. Periodically check that wiring remains supported, terminations stay tight, and the enclosure is still mounted firmly in high-vibration areas.\u003c\/p\u003e","brand":"Vimar","offers":[{"title":"Default Title","offer_id":52269540147381,"sku":"QBP884877","price":23.91,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1300457_qbp884877.jpg?v=1771544502"},{"product_id":"qbp885201","title":"Vimar Isoset IP55 1M Surface Enclosure, For Eikon, Arké \u0026 Plana","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Vimar VM14901 is a surface enclosure that holds one module and is rated IP55. It is used when you want to mount a Vimar Eikon, Arké, or Plana device on a bulkhead or panel while adding protection against dust and water spray in areas that see washdowns.\u003c\/p\u003e\u003cp\u003eThe enclosure is about 83 x 68 x 66 mm (H x W x D) and uses a grey plastic body with insulating construction. Keep the front cover fully closed to maintain the IP55 protection level, and treat it as spray and washdown protection rather than a solution for immersion.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eIP55 protection level for dust and water jets from typical deck and cockpit washdowns\u003c\/li\u003e\n\u003cli\u003e1-module capacity for Vimar Eikon, Arké, and Plana mechanisms\u003c\/li\u003e\n\u003cli\u003eSurface-mount format for refits and exposed mounting locations where a recessed box is not practical\u003c\/li\u003e\n\u003cli\u003eApprox. 83 x 68 x 66 mm overall size (H x W x D) for tight helm, cabin, and utility panels\u003c\/li\u003e\n\u003cli\u003ePlastic housing with insulating construction to reduce accidental contact risk during installation and service\u003c\/li\u003e\n\u003cli\u003eGrey finish that blends well with most consoles, bulkheads, and locker interiors\u003c\/li\u003e\n\u003cli\u003eCable entry provision for bringing wiring into the enclosure without leaving the opening exposed\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis enclosure is made for a single 1-module device from the Vimar Eikon, Arké, and Plana families. Confirm the mechanism you plan to install is a true 1-module format and that you have the matching front parts for the series you are using, since the enclosure itself is only the protected housing.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eMount the enclosure on a flat surface with appropriate fasteners for your substrate, then route conductors through the cable entry and make terminations to the installed mechanism per the device instructions. In exposed marine locations, sealing screw penetrations and managing cable entry to shed water helps the install stay dry behind the cover. Use tinned marine wire and secure the run to handle vibration.\u003c\/p\u003e\u003ch6\u003eUse cases on board\u003c\/h6\u003e\u003cp\u003eThis type of IP55 surface enclosure is a good match for switches and small control points installed in cockpits, deck access areas, lockers, and utility spaces where spray happens and hands are often wet. It is also useful at the helm or nav station when you want a surface-mounted solution without cutting a deep hole in a finished panel.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eRinse off salt residue when you can and wipe the sealing surfaces clean so the cover closes fully. During routine checks, confirm the cover still seats properly and that wiring remains strain-relieved inside the box.\u003c\/p\u003e","brand":"Vimar","offers":[{"title":"Default Title","offer_id":52269540507829,"sku":"QBP885201","price":9.05,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1300461_qbp885201.jpg?v=1771544505"},{"product_id":"qbp878550","title":"Vimar 8000 Series 1-Module Surface Mount Box with Backplate, 40mm Depth, IP20, Ivory Finish","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Vimar VM09956 is a 1-module surface mounting box with backplate, 40 mm depth, for one 8000 standard module installation, in an ivory finish. The box measures 79.5 mm long by 36.5 mm wide and is rated IP20 for protected interior locations.\u003c\/p\u003e\u003cp\u003eUse it when you need a clean surface mount on a bulkhead or headliner and there is no room or no desire to recess a box into the panel. The cover screws on, which helps it stay put on boats that see vibration.\u003c\/p\u003e\u003cp\u003eThis enclosure is intended for dry, indoor-type areas on board. Keep it out of direct spray and washdowns, and plan a different enclosure where water protection is required.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eAccepts one 8000 standard module (1M) when used with the appropriate mounting frame and cover plate.\u003c\/li\u003e\n\u003cli\u003e40 mm depth for surface installs where wiring needs extra space behind the module.\u003c\/li\u003e\n\u003cli\u003eOverall size: 79.5 x 36.5 x 40 mm (L x W x D).\u003c\/li\u003e\n\u003cli\u003eWall or ceiling mounting for flexible placement on bulkheads and headliners.\u003c\/li\u003e\n\u003cli\u003eIP20 enclosure rating for interior spaces that stay dry.\u003c\/li\u003e\n\u003cli\u003eHalogen-free plastic housing with an untreated surface finish.\u003c\/li\u003e\n\u003cli\u003eIvory color matched to RAL 9001.\u003c\/li\u003e\n\u003cli\u003eWorking temperature range: 0 to 60 C.\u003c\/li\u003e\n\u003cli\u003eScrew-fastened cover for a secure closure.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eWhat’s included\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eSurface mounting box body\u003c\/li\u003e\n\u003cli\u003eBackplate (bottom)\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis box is for 8000 standard 1-module devices. It is used with the matching mounting frame and cover plate chosen for the specific switch, socket, or accessory you are installing.\u003c\/p\u003e\u003cp\u003eDevices with codes starting 08064 or 08065 are not supported by this box.\u003c\/p\u003e\u003cp\u003eThis is the enclosure only. Electrical ratings, circuit protection, and marine compliance depend on the installed module and the way the circuit is built on the boat.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eSurface mounting keeps the panel intact, but plan wire routing first so you have enough slack for terminations once the module is seated in the mounting frame. Keep bends gentle and avoid pinching conductors at the box edge.\u003c\/p\u003e\u003cp\u003eOn a boat, mount the box to a flat, solid surface so the finished plate sits square. If the mounting surface is thin, adding backing material behind the screws helps prevent looseness over time.\u003c\/p\u003e\u003ch6\u003eMaterials and protection\u003c\/h6\u003e\u003cp\u003eThe plastic body is halogen-free and the enclosure is IP20, so it belongs in protected spaces. In salty environments, keeping the installation dry and easy to wipe down helps the connected device stay clean and trouble-free.\u003c\/p\u003e\u003ch6\u003eUse on board\u003c\/h6\u003e\u003cp\u003eThis type of box is a good match for refits where a single Vimar module is being added without cutting into a bulkhead, such as at a nav station, cabin entry, or inside a dry locker. It also works well when you want the module to sit proud of the surface for easier access to wiring behind the device.\u003c\/p\u003e","brand":"Vimar","offers":[{"title":"Default Title","offer_id":52269542637749,"sku":"QBP878550","price":18.0,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1300351_qbp878550.jpg?v=1771544518"},{"product_id":"qbp878749","title":"Vimar 3-Module Surface\/Table Mounting Box, For 8000\/Linea\/7000 Series, With Backplate, 80 x 124 x 40 mm, IP20, Plastic, Rear Cable Entry, 6 Inlets, Ui 450V","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Vimar VM09968 is a 3-module surface or table mounting box with a 40 mm backplate for Vimar 8000, Linea, and 7000 series devices. It measures 80 x 124 x 40 mm and gives you a clean way to mount modular controls when a flush box is not available or you do not want to cut into a panel or bulkhead.\u003c\/p\u003e\u003cp\u003eFor fit, plan around a cover plate size up to 80 x 124 mm and installed device depth up to 38 mm. The box is IP20 and not weatherproof, so it belongs in protected interior locations rather than exposed cockpits or areas that get washdowns.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e3-module surface or table mounting box with backplate, 40 mm depth\u003c\/li\u003e\n\u003cli\u003eOverall dimensions: 80 x 124 x 40 mm\u003c\/li\u003e\n\u003cli\u003eCompatibility with Vimar 8000, Linea, and 7000 series mounting frames and cover plates, including self-bearing cover plates\u003c\/li\u003e\n\u003cli\u003eSix cable inlets with rear entry support for tidy routing behind liners and panels\u003c\/li\u003e\n\u003cli\u003eScrew cord-grip cable entry support for table installations where strain relief matters\u003c\/li\u003e\n\u003cli\u003eCover attachment is screwed, which helps keep everything stable in areas that see vibration\u003c\/li\u003e\n\u003cli\u003eIP20, working temperature 0 to 60 °C, rated insulation voltage Ui 450 V\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis is a 3-module box sized around cover plates up to 80 x 124 mm. Before ordering devices, check the installed depth of the mechanisms and wiring so the total depth stays within 38 mm and the cover sits flat.\u003c\/p\u003e\u003cp\u003eIt is intended for surface or table mounting with the matching frames and plates from the Vimar 8000, Linea, and 7000 families. If you are mixing series, verify the frame and cover plate you are using is listed for a 3-module rectangular mounting box in that range.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eFor surface mounting, secure the base to the bulkhead or panel using the fixing slots, then route the cable through a suitable entry point and complete the assembly with the chosen frame, device modules, and cover plate. For table mounting, the cord-grip entry is used to anchor the cable so it does not pull on terminals when the unit gets moved.\u003c\/p\u003e\u003cp\u003eWhen installing multiple boxes side by side, the built-in alignment and fastening features help keep spacing consistent so the finished row of frames and plates lines up cleanly.\u003c\/p\u003e\u003ch6\u003eUse cases on board\u003c\/h6\u003e\u003cp\u003eThis box fits refits and additions where you need a surface-mounted switch, outlet, or control set in cabins, nav stations, inside helm consoles, and other protected spaces. It is also a practical choice when a liner, furniture panel, or wiring chase makes a flush box awkward.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eKeep it in a dry, protected area and avoid direct spray or washdowns due to the IP20 rating. If it needs cleaning, wipe with a damp cloth and mild soap, and keep water away from live devices and terminations.\u003c\/p\u003e","brand":"Vimar","offers":[{"title":"Default Title","offer_id":52269543260341,"sku":"QBP878749","price":12.08,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1300356_qbp878749.jpg?v=1771544522"},{"product_id":"qbp878810","title":"Vimar 3-Module Surface Mounting Box, For 8000 and Linea, White Housing, 48mm Depth, IP20","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Vimar VM09974 is a 3-module surface mounting box for Vimar 8000 and Linea components when you need a clean, surface-run install instead of cutting into a bulkhead. The enclosure is 80 mm long, 124 mm wide, and 48 mm deep, with an IP20 protection rating for use in dry, protected interior areas.\u003c\/p\u003e\u003cp\u003eIt mounts on walls or overhead panels and includes multiple entry points to route wiring neatly into the box. The cover is secured with screws, which helps keep everything closed up when the boat is moving and wiring is tied down properly.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e3-module surface box format for Vimar 8000 and Linea mounting frames and cover plates\u003c\/li\u003e\n\u003cli\u003e48 mm depth with overall dimensions of 80 x 124 x 48 mm for space planning behind trim and cabinetry\u003c\/li\u003e\n\u003cli\u003eHalogen-free plastic housing with a white finish\u003c\/li\u003e\n\u003cli\u003eWall or ceiling mounting, suitable for insulating non-perforated surfaces and earthed metallic surfaces\u003c\/li\u003e\n\u003cli\u003eFour cable or conduit entry points sized for 20 mm or 25 mm runs, plus rear inlet support\u003c\/li\u003e\n\u003cli\u003eIP20 rating for interior locations where the box is not exposed to spray or washdowns\u003c\/li\u003e\n\u003cli\u003eOperating temperature range from 0°C to 60°C\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis box is meant for Vimar modular hardware in a 3-module layout. It is used as the surface back box behind the matching support and plate, so the finished install sits proud of the mounting surface by the box depth rather than being recessed.\u003c\/p\u003e\u003cp\u003eBefore ordering, confirm your system uses the 8000 or Linea format and that your selected frame and cover plate are sized for 3 modules.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003ePlan cable routing first, then choose the most direct inlet for the run so the conductors enter without sharp bends. If you are mounting to a metallic panel, ensure the surface is properly earthed and keep wiring protected from chafe where it passes through entry points.\u003c\/p\u003e\u003cp\u003eBecause this is an IP20 enclosure, it belongs in dry interior spaces such as cabins, nav stations, inside lockers, or other protected panels. Avoid mounting where it can see direct spray, dripping lines, or regular washdowns.\u003c\/p\u003e\u003ch6\u003eUse cases on board\u003c\/h6\u003e\u003cp\u003eThis style of surface box is a good match for refits where you are adding or relocating Vimar modules but do not want to cut into fiberglass, core, or finished joinery. It is also useful when wiring needs to remain accessible behind the plate for future service.\u003c\/p\u003e","brand":"Vimar","offers":[{"title":"Default Title","offer_id":52269543456949,"sku":"QBP878810","price":12.6,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1300357_qbp878810.jpg?v=1771544524"},{"product_id":"qbp880439","title":"Vimar Linea Classica 2-Module Surface Enclosure, For Linea 2M, IP55","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Vimar VM12202 is an IP55-rated 2-module surface enclosure for Vimar Linea 2M components. It gives you a protected housing when you need to mount Linea devices on top of a bulkhead or panel instead of cutting in a recessed box.\u003c\/p\u003e\u003cp\u003eOn a boat, IP55 protection is useful in spots that see spray, dust, and day-to-day wipe-downs, such as a pilothouse, a covered cockpit, or a utility area where moisture is part of normal life onboard. The insulating plastic body also helps when you are installing on insulated walls or mixed-material panels.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eIP55 protection for electrical modules in areas exposed to spray and airborne dust\u003c\/li\u003e\n\u003cli\u003e2-module capacity for Linea 2M layouts where space is tight on a console or bulkhead\u003c\/li\u003e\n\u003cli\u003eSurface-mount format for refits and finished panels where flush mounting is not practical\u003c\/li\u003e\n\u003cli\u003eInsulating plastic enclosure suitable for installations on insulated surfaces\u003c\/li\u003e\n\u003cli\u003eMade to pair with Vimar Linea 2M components for consistent fit and alignment\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis enclosure is sized for 2-module Linea 2M configurations. Before ordering, confirm your planned device layout is 2 modules and matches the Linea family you are using, especially if you are standardizing multiple stations around the boat.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eSurface mounting is straightforward on a flat, stable area with enough clearance for wiring behind the device. For marine installs, route cables so they are supported against vibration and seal any cable entry points with the right marine glands or sealing methods for your installation so water does not track into the back of the enclosure.\u003c\/p\u003e\u003cp\u003eIP55 is intended for exposure to splashes and dust rather than submersion. If the mounting spot is in the direct path of washdown hoses or heavy green water, place it where it has some shielding or add a drip loop and extra sealing attention around entries.\u003c\/p\u003e\u003ch6\u003eUse cases on board\u003c\/h6\u003e\u003cp\u003eThis enclosure makes sense for adding a small control point on a bulkhead, console side, or locker area where you want a surface-mounted, protected module position. It is a solid fit for owners and installers building out Linea stations in cruising boats where space is limited and the environment stays humid.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eWipe the enclosure with fresh water and a mild soap when needed, especially after salt exposure. Periodically check that the sealing surfaces remain clean and that cable entries stay tight, since small gaps are usually what let moisture work its way into electrical spaces over time.\u003c\/p\u003e","brand":"Vimar","offers":[{"title":"Default Title","offer_id":52269547258037,"sku":"QBP880439","price":14.65,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1300369_qbp880439.jpg?v=1771544540"},{"product_id":"qbp892661","title":"Vimar Surface-Mount Junction Box, IP56, 190 x 140 x 70 mm, Undrilled Walls, Blind Cover, Stainless Steel Screws, RAL 7035 Grey, 450 V","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Vimar VMV55207 is an IP56-rated surface-mount junction box used to protect electrical connections in areas that see spray, washdowns, and general moisture on board. The enclosure measures 190 x 140 x 70 mm and comes in RAL 7035 grey, with a plastic body and a blind cover that fastens down with stainless steel screws.\u003c\/p\u003e\u003cp\u003eIt is rated with an insulation voltage (Ui) of 450 V and is specified for use from 0 C to 60 C. The walls are undrilled, so cable entries can be placed where they make sense for your run and finished with the right glands or conduit fittings to keep the seal intact.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eIP56 protection for spray and washdowns in exposed areas\u003c\/li\u003e\n\u003cli\u003eSurface-mount format for bulkheads, lockers, and panels\u003c\/li\u003e\n\u003cli\u003eUndrilled walls so cable entries can be placed where your wiring actually routes\u003c\/li\u003e\n\u003cli\u003eBlind cover secured with stainless steel screws\u003c\/li\u003e\n\u003cli\u003eOverall size: 190 x 140 x 70 mm\u003c\/li\u003e\n\u003cli\u003eRated insulation voltage (Ui): 450 V\u003c\/li\u003e\n\u003cli\u003eSpecified working temperature: 0 C to 60 C\u003c\/li\u003e\n\u003cli\u003eRAL 7035 grey finish for a neutral, low-visibility install\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eMount the box to a flat surface where the cover screws remain accessible for future inspections. Plan entry points before drilling, then use appropriate cable glands or conduit fittings sized for your cable and jacket so the seal is not compromised. Leave enough slack inside for service, keep splices or terminal blocks supported, and tighten the cover screws evenly so the gasket seats consistently.\u003c\/p\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis is a protective enclosure, so the electrical limits of your installation depend on the terminals, connectors, and cable you install inside it. The 450 V insulation rating suits many common on-board circuits, but it does not replace correct fuse or breaker sizing, proper strain relief, or good separation between DC and AC wiring where required. Confirm the footprint fits your mounting area and that you can route cables without sharp bends at the entry points.\u003c\/p\u003e\u003ch6\u003eUse on board\u003c\/h6\u003e\u003cp\u003eThis box is a good match when you are cleaning up exposed junctions on deck, in cockpit lockers, under hardtops, or around masts and radar supports where wiring needs protection from spray. It also works well during refits where cable routing is not standardized and you want the freedom to place entries exactly where the run dictates.\u003c\/p\u003e\u003ch6\u003eMaintenance and checks\u003c\/h6\u003e\u003cp\u003eAfter the first few outings, recheck gland tightness and confirm the cover gasket is seated properly. In saltwater use, a quick rinse and periodic inspection for grit around the seal helps maintain the IP rating over time.\u003c\/p\u003e","brand":"Vimar","offers":[{"title":"Default Title","offer_id":52269574389941,"sku":"QBP892661","price":29.57,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1300611_qbp892661.jpg?v=1771544667"},{"product_id":"qbp892749","title":"Vimar Surface-Mount Junction Box, IP56, 240x190x90mm, Undrilled Walls, Blind Cover, Stainless Steel Screws, 450V Insulation Voltage","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Vimar VMV55208 is a surface-mount IP56 junction box for protecting electrical connections on board when you want a sealed enclosure that still stays serviceable. It measures 240 x 190 x 90 mm and uses smooth, undrilled walls so cable entries can be placed where your wiring run actually lands.\u003c\/p\u003e\u003cp\u003eThe cover is a blind lid secured with stainless steel screws, and the enclosure is finished in RAL 7035 grey. IP56 protection suits lockers, consoles, and other areas that see spray and washdowns, but it is not meant for locations that can stay submerged.\u003c\/p\u003e\u003cp\u003eWith a rated insulation voltage (Ui) of 450 V and an operating temperature range of 0 to 60 C, it fits a wide mix of onboard circuits as long as the cable entries are sealed correctly with appropriate glands or conduit fittings.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eIP56 enclosure for dust exposure and water jets from washdowns and spray\u003c\/li\u003e\n\u003cli\u003e240 x 190 x 90 mm surface-mount box for bulkheads, console backs, and overhead panels\u003c\/li\u003e\n\u003cli\u003eSmooth, undrilled walls for custom cable entry placement\u003c\/li\u003e\n\u003cli\u003eBlind cover fastened with stainless steel screws for repeat access during service\u003c\/li\u003e\n\u003cli\u003ePlastic enclosure in RAL 7035 grey for a clean, neutral look in technical spaces\u003c\/li\u003e\n\u003cli\u003eRated insulation voltage (Ui): 450 V\u003c\/li\u003e\n\u003cli\u003eOperating temperature range: 0 to 60 C\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eMark the cable entry points after you have the box positioned, then drill for the glands or conduit fittings that match your cable and routing. The seal is only as good as the entries, so take the time to deburr holes, seat fittings flat, and keep strain off the conductors inside the box.\u003c\/p\u003e\u003cp\u003eMount it on a rigid, reasonably flat surface so the lid seats evenly. In areas that see heavy vibration, leave enough service loop to avoid pulling on terminations when the boat is underway.\u003c\/p\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis is a surface-mount enclosure for building a protected junction point where you cannot or do not want to recess a box. Before ordering, check the available mounting footprint and the clearance needed to open the cover and route cables without tight bends.\u003c\/p\u003e\u003ch6\u003eElectrical and system integration\u003c\/h6\u003e\u003cp\u003eUse it as a protected space for splices, terminal blocks, or small distribution points, and keep separation and labeling consistent with the rest of the vessel. The enclosure rating does not replace good practice inside the box, so match connectors and terminations to the circuit type and environment.\u003c\/p\u003e\u003ch6\u003eUse on board\u003c\/h6\u003e\u003cp\u003eThis box makes sense for refits and new builds where you need one accessible junction point for wiring runs to deck equipment, lighting, pumps, sensors, or helm accessories, while keeping the connections covered from spray and general grime.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eAfter the first few outings, recheck cover screw tightness and inspect cable entries for movement or gaps. If the box lives in a salty, wet area, rinse exterior salt buildup during routine washdowns and open it periodically to confirm connections stay clean and dry.\u003c\/p\u003e","brand":"Vimar","offers":[{"title":"Default Title","offer_id":52269575209141,"sku":"QBP892749","price":46.02,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1300612_qbp892749.jpg?v=1771544668"},{"product_id":"qbp892875","title":"Vimar 8-Module Rectangular Flush Mounting Box, For Masonry Walls, Glow Wire 650°C, Halogen-Free Plastic, 20\/25 mm Conduit Knockouts, Light Blue","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Vimar VMV71318 is an 8-module flush mounting box for masonry walls, sized at 145.00 mm x 124.50 mm with an inner depth of 50.00 mm and an installation depth that can be set up to 56.80 mm. It gives you a clean in-wall base for mounting 8-module device supports and keeping terminations and cable routing organized behind the finished faceplate.\u003c\/p\u003e\u003cp\u003eThe light blue body makes it easy to spot during rough-in, and the box is built around typical conduit-style installations with break-out entries for 20 mm and 25 mm runs. For marine projects, it fits best in protected, building-style spaces such as marina facilities, dock utility rooms, or interior refit areas where wiring is routed in conduit inside solid walls.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e8-module rectangular flush mounting box intended for masonry walls\u003c\/li\u003e\n\u003cli\u003eOverall size 145.00 mm (L) x 124.50 mm (W) with 50.00 mm inner depth\u003c\/li\u003e\n\u003cli\u003eDepth range up to 56.80 mm to suit different wall builds and finish thickness\u003c\/li\u003e\n\u003cli\u003eGlow Wire 650°C rating for higher heat resistance in the wall cavity\u003c\/li\u003e\n\u003cli\u003eBreak-out openings for 20 mm and 25 mm conduit, with rear cable entry support\u003c\/li\u003e\n\u003cli\u003eCouplable format supports multi-box banks when using compatible coupling joints\u003c\/li\u003e\n\u003cli\u003eZinc-plated fixing lugs help keep threads clear so device supports screw in cleanly after plastering\u003c\/li\u003e\n\u003cli\u003eAccessory-ready layout supports items such as anti-mortar covers and a rack for a dividing screen\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis box is built around an 8-module layout, so confirm the device support and front frame you are installing are the matching 8-module format. Before cutting in, check the available cavity depth and finishing layers so the box can sit flush and still leave working room for conductors behind the device.\u003c\/p\u003e\u003cp\u003eFor conduit runs, plan entries around 20 mm or 25 mm pipe sizes and use the break-out points that keep bends gentle and cable pulls clean. If you are coupling multiple boxes, keep alignment tight at the rough-in stage so the finished frames sit straight across the whole bank.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eSet the box into the masonry opening so the front edge lands flush with the intended finished surface. Pop the required knockouts, route conduits, and leave enough slack for terminations and device removal later. During plastering and finishing, keeping the box protected helps prevent debris from building up where the device support needs to seat and screw down.\u003c\/p\u003e\u003cp\u003eOnce the wall is finished, mount the device support by screwing it into the fixing lugs, then complete terminations and fit the faceplate. If you are dividing circuits inside the box, a separating screen can be fitted where your installation calls for it.\u003c\/p\u003e\u003ch6\u003eUse cases on board\u003c\/h6\u003e\u003cp\u003eThis is a practical match for electricians and boatyard teams building out shore-side electrical areas or interior refit spaces that use in-wall conduit and modular switching. For exterior marine locations exposed to spray or washdowns, use an enclosure that carries an appropriate IP rating for the environment.\u003c\/p\u003e","brand":"Vimar","offers":[{"title":"Default Title","offer_id":52269575471285,"sku":"QBP892875","price":9.36,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1300614_qbp892875.jpg?v=1771544673"},{"product_id":"qbp892915","title":"Vimar 12\/14-Module Flush Mounting Box, For Masonry Walls, Rectangular, 134x180x50 mm, Halogen-Free Plastic, Glow Wire 650C, 20\/25 mm Conduit Knockouts, Light Blue","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Vimar VMV71320 is a 12\/14-module flush mounting box for masonry walls, sized for larger multi-module switch and outlet layouts. The box footprint is 134 mm x 180 mm with a 50 mm inner depth, giving you room to dress conductors cleanly behind the devices instead of forcing tight bends.\u003c\/p\u003e\u003cp\u003eIt is built with 14 inlets and knockouts that suit 20 mm and 25 mm conduit runs, which helps when you are feeding multiple circuits into one location. Because it is rated IP00, it belongs in dry, enclosed interior spaces where the front devices and cover plate provide the finished protection.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e12\/14-module flush box format for multi-gang device groupings in one wall location\u003c\/li\u003e\n\u003cli\u003eMade for masonry walls with flush-mounted installation\u003c\/li\u003e\n\u003cli\u003e134 mm x 180 mm overall size with 50 mm inner depth to keep wiring manageable behind the devices\u003c\/li\u003e\n\u003cli\u003e14 inlets with knockouts for 20 mm and 25 mm conduit paths\u003c\/li\u003e\n\u003cli\u003eHalogen-free plastic body with glow-wire resistance to 650 C\u003c\/li\u003e\n\u003cli\u003ePatented rack for fixing a dividing screen when separation inside the box is needed\u003c\/li\u003e\n\u003cli\u003eZinc-plated fixing lugs help threads stay cleaner during installation and rework\u003c\/li\u003e\n\u003cli\u003eIP00 protection level, intended to be used inside a finished wall system rather than exposed areas\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis box is intended for installations that use the 12\/14-module format and require a rectangular flush box behind the finished devices. Confirm you have a masonry wall build-up that can accept the box depth, and plan conduit entries so the 20 mm or 25 mm runs land on the knockouts you want to use.\u003c\/p\u003e\u003ch6\u003eInstallation notes\u003c\/h6\u003e\u003cp\u003eOn a typical masonry install, the box is set in place and plastered flush so the device mounting points remain square and accessible. With a larger box like this, it helps to map conduit routes early so the inlets you use do not crowd the device area once conductors are pulled.\u003c\/p\u003e\u003cp\u003eIf you need separation between groups of conductors inside the same cavity, the internal rack supports fitting a dividing screen so the layout stays organized.\u003c\/p\u003e\u003ch6\u003eUse on board\u003c\/h6\u003e\u003cp\u003eFor marine projects, this style of flush box is most common in shore-side or onboard interior refits where the wall construction is masonry or a similar solid build-up, such as crew areas or service spaces in facilities around the marina. It is not a good match for locations exposed to spray, washdowns, or persistent damp, and it is generally not the right choice for thin fiberglass panels or hollow partitions.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eOnce installed, keep the surrounding wall area dry and inspect during refits if there is any sign of moisture migration through the wall. In salt-air environments, good practice is to keep connections clean, avoid leaving the box open during construction, and close out the installation promptly with the intended devices and cover plate.\u003c\/p\u003e","brand":"Vimar","offers":[{"title":"Default Title","offer_id":52269575536821,"sku":"QBP892915","price":10.23,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1300618_qbp892915.jpg?v=1771544677"},{"product_id":"qbp893916","title":"Vimar 8-Module Flush-Mount Box for Hollow Walls, 138 x 138 x 56 mm, 50 mm Internal Depth, For 20\/25 mm Conduit, Halogen-Free Plastic, GW 850C, Light Blue Housing","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Vimar VMV71718 is an 8-module flush-mount box for hollow walls, used to recess a modular switch or outlet bank into thin panels on boats. The box is 138 x 138 mm with up to 56 mm overall depth and about 50 mm internal depth, so you can plan device clearance behind the finish panel.\u003c\/p\u003e\u003cp\u003eIt mounts into hollow wall materials like plywood panels, laminated boards, and similar lightweight bulkheads. Cable entry is handled through 16 knockouts, including rear entry, and the retention-style knockouts are sized around common conduit runs (16, 20, or 25 mm). The mounting system uses metal fins to clamp to wall thicknesses from 1 to 38 mm, plus metal lugs for the support screws that hold the devices in place.\u003c\/p\u003e\u003cp\u003eThis is a good match for interior refits where you want a clean, flush look at a nav station, cabin, or saloon panel, and you are routing wiring in conduit or protected looms behind the liner. Since the box is IP00, it belongs in dry locations away from spray and washdowns.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e8-module flush-mount box for hollow-wall installations (module layout noted as 4+4)\u003c\/li\u003e\n\u003cli\u003eFits within a 138 x 138 mm footprint with up to 56 mm overall depth and about 50 mm internal depth\u003c\/li\u003e\n\u003cli\u003eHollow-cutter preparation based on a 68 mm diameter, with a built-in centring plate to help position the cutout\u003c\/li\u003e\n\u003cli\u003eMetal clamping fins support panel thicknesses from 1 to 38 mm for a secure hold in thin bulkheads and furniture panels\u003c\/li\u003e\n\u003cli\u003e16 cable entries, including rear entry, with retention-style knockouts for conduit sizes 16, 20, or 25 mm\u003c\/li\u003e\n\u003cli\u003eHalogen-free plastic construction with a glow-wire rating of 850 C\u003c\/li\u003e\n\u003cli\u003eIP00 rating, intended for dry interior spaces\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis box is meant for hollow-wall mounting, not solid fiberglass or solid timber where you cannot clamp the fins behind the surface. It is sized for an 8-module device arrangement, so confirm your chosen Vimar modular devices and cover plate are the 8-module format before cutting.\u003c\/p\u003e\u003cp\u003eDepth is usually the deciding factor behind helm consoles and bulkheads with tight clearances. Use the 56 mm maximum depth and 50 mm internal depth as your guide when checking for obstructions like stringers, ducting, and existing looms.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eLay out the opening carefully on the finished surface, then prepare the cutout using the 68 mm hollow-cutter reference and the centring features on the box. Once positioned, tighten the clamping fins so the box locks to the panel without crushing the laminate or liner.\u003c\/p\u003e\u003cp\u003eBring wiring in through the knockouts and keep the run supported so vibration does not pull on the devices. In saltwater environments, using corrosion-resistant fasteners for any mounting hardware around the cutout helps keep the installation serviceable over time.\u003c\/p\u003e\u003ch6\u003eEnvironmental and location notes\u003c\/h6\u003e\u003cp\u003eThis is not a sealed enclosure. Keep it inside dry cabins, behind interior liners, or in protected consoles where it will not see spray, dripping condensation, or washdowns. If the mounting surface is in a damp area, address moisture at the panel level first (gaskets, drip loops, and loom protection) rather than relying on the box for water protection.\u003c\/p\u003e","brand":"Vimar","offers":[{"title":"Default Title","offer_id":52269590806709,"sku":"QBP893916","price":17.23,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1300640_qbp893916.jpg?v=1771544748"},{"product_id":"qbp894195","title":"Vimar 12-14 Module Flush-Mount Box for Hollow Walls, 68 mm Cutout, 50 mm Internal Depth, Halogen-Free Plastic, GW 850C, Blue","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Vimar VMV71720 is a 12 to 14-module flush-mount box for hollow walls that lets you recess Vimar modular devices into lightweight panels and liners on board. The box measures 199.3 mm wide by 142.8 mm long, with 50 mm internal depth and an overall depth range of 0 to 70 mm. Protection is IP00, so it is meant to sit behind a finished plate and in a protected, interior location.\u003c\/p\u003e\u003cp\u003eCutouts are made with a 68 mm hole saw, and the integrated centring plate helps keep the openings aligned during layout. Metal fins clamp the box securely to wall thicknesses from 1 to 38 mm, and the built-in breakouts handle common conduit runs (16, 20, or 25 mm) with 10 inlets for cable entry. The body is halogen-free plastic with a GW 850 C rating.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eFlush-mount box sized for 12 to 14-module installations\u003c\/li\u003e\n\u003cli\u003e199.3 mm x 142.8 mm footprint with 50 mm internal depth\u003c\/li\u003e\n\u003cli\u003eWall thickness clamp range: 1 to 38 mm (metal fins)\u003c\/li\u003e\n\u003cli\u003eHole preparation with a 68 mm hole saw using the integrated centring plate\u003c\/li\u003e\n\u003cli\u003e10 inlets with knockouts shaped for 16, 20, and 25 mm conduit runs\u003c\/li\u003e\n\u003cli\u003eHalogen-free plastic body with GW 850 C rating\u003c\/li\u003e\n\u003cli\u003eConnectable format for series mounting when used with compatible accessories\u003c\/li\u003e\n\u003cli\u003eBlue housing helps visibility during rough-in and refits\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis box is intended for hollow wall builds where the panel is a liner or lightweight bulkhead and the rear side is accessible during installation. Confirm the module count (12 or 14) of the devices and frames you are installing, and check that you have enough clearance behind the panel for the box depth and cable bend radius.\u003c\/p\u003e\u003ch6\u003eInstallation and onboard use notes\u003c\/h6\u003e\u003cp\u003ePlan conduit and cable routes before cutting, then use the breakouts that best match your entry direction to keep wiring tidy behind the finished plate. On boats, it is typically used in dry interior zones such as cabins, salons, nav stations, and inside protected lockers where you want multiple controls or outlets grouped in one place.\u003c\/p\u003e\u003cp\u003eBecause the enclosure is IP00, avoid exposed locations that see washdown, spray, or condensation drip paths. If the space can get damp, route cables to prevent water tracking into the opening and keep terminations protected according to the requirements of your electrical installation.\u003c\/p\u003e","brand":"Vimar","offers":[{"title":"Default Title","offer_id":52269591330997,"sku":"QBP894195","price":20.57,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1300645_qbp894195.jpg?v=1771544765"},{"product_id":"qbp889664","title":"Vimar Surface-Mount Consumer Unit, 5-Module, IP40, Transparent Door","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Vimar VMV50405 is a surface-mount consumer mounting box with a vertically hinged transparent door and space for 5 modules (4+1).\u003c\/p\u003e\u003cp\u003eIt carries an IP40 rating for protection against solid objects larger than 1 mm, so it belongs in dry, protected areas such as an interior electrical locker, behind an inside console panel, or an enclosed technical space. Overall size is 170 mm high, 145 mm wide, and 95 mm deep, which helps when you need a compact enclosure without cutting into a bulkhead.\u003c\/p\u003e\u003cp\u003eThe housing is plastic in a grey RAL 7035 finish, includes a DIN rail, and is pre-set for support of the V51859 earth terminal block.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eSurface-mounted enclosure for 5 modular spaces (4+1) in a single row\u003c\/li\u003e\n\u003cli\u003eIP40 protection for interior locations where the box is not exposed to spray or washdowns\u003c\/li\u003e\n\u003cli\u003eTransparent door with a vertical hinge so device positions can be checked without opening the cover\u003c\/li\u003e\n\u003cli\u003eDIN-rail ready for compatible modular components\u003c\/li\u003e\n\u003cli\u003eTop and bottom knockouts for cable entry and routing flexibility\u003c\/li\u003e\n\u003cli\u003e170 mm x 145 mm x 95 mm overall size for compact installs\u003c\/li\u003e\n\u003cli\u003eGrey RAL 7035 finish that keeps a clean, neutral look on board\u003c\/li\u003e\n\u003cli\u003ePre-set for support of the V51859 earth terminal block\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eMount the enclosure to a flat surface using fasteners suited to the bulkhead or panel material, and leave clearance so the door can swing fully. Plan cable entry so conductors do not rub or pinch at the knockouts when the door is closed.\u003c\/p\u003e\u003cp\u003eAfter pulling in wiring from the top or bottom, dress conductors neatly and support heavier cable runs close to the entry point, especially in areas that see vibration.\u003c\/p\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis box is intended for modular components that mount on a DIN rail and fit within 5 module spaces. Confirm the module width of the devices you plan to install and allow room for wiring bend radius within the 95 mm depth.\u003c\/p\u003e\u003cp\u003eOn boats, the IP40 rating is the key limiter: it is not a water seal. Use it in protected compartments rather than in cockpits, open helm areas, or other locations that see washdowns.\u003c\/p\u003e\u003ch6\u003eUse cases on board\u003c\/h6\u003e\u003cp\u003eIt is commonly used as a small distribution point near a nav station, a service enclosure for interior circuits, or a tidy control box inside an enclosed technical locker. It fits well when you want a closed cover for safety and quick visual checks through the transparent door.\u003c\/p\u003e","brand":"Vimar","offers":[{"title":"Default Title","offer_id":52269606994101,"sku":"QBP889664","price":44.99,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1300586_qbp889664.jpg?v=1771544819"},{"product_id":"qbp889957","title":"Vimar Surface-Mount Consumer Unit, 8-Module, IP40, Transparent Door, DIN Rail, 215 x 170 x 95 mm","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Vimar VMV50408 is a surface-mounted consumer unit enclosure with a vertically hinged transparent door and space for 8 modular components in a single row. It is rated IP40 and is meant for locations on board that stay dry and are protected, where you need an organized place for modular protection and control devices.\u003c\/p\u003e\u003cp\u003eThe housing is plastic in RAL 7035 grey and includes a DIN rail. Overall size is 215 mm wide, 170 mm high, and 95 mm deep, with 94 mm of inner depth for wiring and device terminations.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e8-module, 1-row surface enclosure for modular devices, with a closed front and transparent door for quick visual checks\u003c\/li\u003e\n\u003cli\u003eIP40 protection level for interior installations where water spray and washdowns are not expected\u003c\/li\u003e\n\u003cli\u003eTop and bottom knockouts to route cables in from overhead or below while keeping runs tidy\u003c\/li\u003e\n\u003cli\u003eDIN rail supplied for mounting the modular components inside the box\u003c\/li\u003e\n\u003cli\u003ePre-set support for an earth terminal block (V51860) to keep protective conductors grouped and accessible\u003c\/li\u003e\n\u003cli\u003eCompact footprint: 215 x 170 x 95 mm (W x H x D), with 94 mm inner depth for wiring space\u003c\/li\u003e\n\u003cli\u003eNo lock and no extension provision, which keeps the enclosure straightforward for fixed layouts\u003c\/li\u003e\n\u003cli\u003eRAL 7035 grey plastic housing that is easy to wipe down in service areas\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eMount the box on a flat bulkhead or panel where you can open the door fully for access. Plan cable entry before drilling out the knockouts, and support incoming conductors so they are not hanging off the terminals, especially on boats that see vibration.\u003c\/p\u003e\u003cp\u003eBecause the enclosure is IP40, place it in a space that stays dry and out of direct spray. If the mounting area can see condensation, route cables so water cannot track along them into the box.\u003c\/p\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis enclosure is sized for 8 modular spacings in one row and is intended for standard modular components that mount to the included rail. The 94 mm inner depth helps when you are working with larger conductors and need room for bends and terminations.\u003c\/p\u003e\u003cp\u003eThere is a provision for fitting an earth terminal block (V51860). If your installation uses a dedicated protective earth grouping inside the enclosure, this keeps those connections together and easy to inspect.\u003c\/p\u003e\u003ch6\u003eUse on board\u003c\/h6\u003e\u003cp\u003eIt suits refits and compact builds where a recessed consumer unit is not practical. Common placements include inside cabins, behind helm consoles, inside electrical lockers, or in other protected technical spaces where you want devices visible through a clear door.\u003c\/p\u003e\u003ch6\u003eMaintenance and checks\u003c\/h6\u003e\u003cp\u003ePeriodically open the door and check that terminations remain tight, cables stay supported, and the knockouts have not introduced sharp edges that can chafe insulation. In saltwater environments, keep the enclosure in a sheltered area and wipe away any salt residue that can build up over time.\u003c\/p\u003e","brand":"Vimar","offers":[{"title":"Default Title","offer_id":52269607190709,"sku":"QBP889957","price":44.65,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1300587_qbp889957.jpg?v=1771544821"},{"product_id":"qbp890000","title":"Vimar Surface Consumer Unit, 12+1 Modules, IP40, Transparent Door","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Vimar VMV50412 is an IP40 surface-mounted consumer unit enclosure with a vertically hinged transparent door and room for 12 (12+1) DIN modules. The compact housing measures 185 mm high, 160 mm wide, and 95 mm deep, which makes it easy to mount on a bulkhead or inside a cabinet when you need a tidy place for modular protection and control devices.\u003c\/p\u003e\u003cp\u003eThe transparent door lets you check breaker positions and labeling at a glance while keeping fingers and loose gear away from live parts. Because IP40 does not protect against water, it belongs in a dry, protected spot on board such as inside the cabin, behind the nav station, or within an electrical locker that stays out of spray and washdowns.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eSurface-mounted, single-row enclosure sized for 12 (12+1) modular spacings.\u003c\/li\u003e\n\u003cli\u003eVertically hinged transparent door for quick visual checks without opening the box.\u003c\/li\u003e\n\u003cli\u003eIP40 protection for sheltered interior spaces where you want a barrier against accidental contact and small debris.\u003c\/li\u003e\n\u003cli\u003eBuilt-in DIN rail for standard modular devices.\u003c\/li\u003e\n\u003cli\u003eTop and bottom knockouts to bring cables in cleanly from above or below.\u003c\/li\u003e\n\u003cli\u003eGrey housing in RAL 7035 to match common electrical installs.\u003c\/li\u003e\n\u003cli\u003ePrepared to support the V51861 earth terminal block when used in the installation.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis box is meant for standard DIN-rail modular components used in distribution and control panels. Check the total number of modules your breakers or devices require and allow extra room for wiring bends and cable routing through the top or bottom entries. The enclosure is a fixed, one-row format, so layout planning matters if you are grouping multiple circuits.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eMount the enclosure on a flat, solid surface and leave clearance for the door to swing open. Bring conductors through the knockouts and support wiring so vibration does not pull on terminals. On boats, it helps to route cables with drip loops and keep the unit away from areas that see direct spray, condensation, or frequent washdowns.\u003c\/p\u003e\u003ch6\u003eUse on board\u003c\/h6\u003e\u003cp\u003eThis enclosure is a practical choice when you are adding a small DIN-module distribution point for a refit or a new circuit group and you want everything covered and organized in a compact footprint. It suits coastal and offshore boats that keep their electrical protection gear inside protected interior spaces rather than exposed locations.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003ePeriodically open the door to check for loose conductors, chafe, or signs of moisture. Wipe the door and housing with a lightly damp cloth and mild soap, and avoid solvents that can haze clear plastics. Any re-termination or testing should be done with the system de-energized by qualified personnel.\u003c\/p\u003e","brand":"Vimar","offers":[{"title":"Default Title","offer_id":52269607387317,"sku":"QBP890000","price":73.01,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1300588_qbp890000.jpg?v=1771544823"},{"product_id":"qbp890041","title":"Vimar Surface-Mount Consumer Unit Enclosure, IP55, 12+1 Modules, Horizontally Hinged Transparent Door, DIN Rail","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Vimar VMV51012 is a surface-mounted consumer unit enclosure with a transparent door that swings on a horizontal hinge, sized for 12+1 DIN modules and rated IP55. The housing measures 285 mm wide x 200 mm high x 119 mm deep, with an inner depth of 118 mm, so you can plan clearances for wiring and modular devices before you drill any holes.\u003c\/p\u003e\u003cp\u003eOn a boat, this style of enclosure is typically used to keep DIN-rail breakers, RCDs, fuse holders, and terminals protected in spaces that see dust, damp air, and occasional spray. The clear door makes it easy to check the position of protective devices at a glance without opening the front. There is no lock, so it suits installations where quick access matters and the panel is already located in a controlled area.\u003c\/p\u003e\u003cp\u003eInside, it uses a DIN rail and it comes with screw caps for double insulation. It is also prepared for fitting an earth terminal block support, and it can be adjoined to another consumer unit using joining accessories when you need a wider board.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eIP55 protection level to help keep out dust and water spray in typical onboard compartments\u003c\/li\u003e\n\u003cli\u003e12+1 module capacity on a single row (12 modular spacings)\u003c\/li\u003e\n\u003cli\u003eTransparent door with a horizontal hinge for quick visual checks and straightforward access\u003c\/li\u003e\n\u003cli\u003eClosed front with no lock for fast entry during troubleshooting or routine checks\u003c\/li\u003e\n\u003cli\u003ePlastic enclosure in grey (RAL 7035) that fits cleanly in technical spaces\u003c\/li\u003e\n\u003cli\u003eBuilt-in DIN rail for standard modular components\u003c\/li\u003e\n\u003cli\u003eOverall size: 285 mm (W) x 200 mm (H) x 119 mm (D); inner depth: 118 mm\u003c\/li\u003e\n\u003cli\u003ePrepared for an earth terminal block support and joinable to expand the assembly\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis enclosure is laid out for DIN-rail modular devices, with a 12-module wide row and extra space as indicated by the 12+1 format. Before ordering components, check the depth of any devices you plan to install and leave room for cable bend radius, especially if you are bringing in larger conductors. The inner depth figure is useful when you are working inside a console, locker, or bulkhead space with tight clearance behind the door.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eBecause it is surface-mounted, installation is usually a matter of fixing the housing to a flat bulkhead and then routing cables through properly sealed entries. Use cable glands or fittings that match your wiring and the environment, and keep drip loops where cables run down to the box so water does not track inside. On boats that see vibration, use appropriate backing and fasteners for the mounting surface and re-check fixing points after the first few trips.\u003c\/p\u003e\u003ch6\u003eUse on board\u003c\/h6\u003e\u003cp\u003eThis is a good match when you want a tidy, enclosed place to group circuit protection and terminals in a damp locker, a technical cupboard, a console, or a sheltered cockpit area. It also suits refits where you are adding a dedicated sub-panel and you prefer surface mounting to avoid cutting into finished joinery.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eKeep the door and sealing surfaces clean so the closure stays consistent. After salt exposure, a fresh-water wipe-down and a quick check for grit around the door edge helps the enclosure continue to close properly. During routine electrical inspections, verify the door hinges freely and that internal wiring is not pushing against the cover.\u003c\/p\u003e","brand":"Vimar","offers":[{"title":"Default Title","offer_id":52269607583925,"sku":"QBP890041","price":111.06,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1300589_qbp890041.jpg?v=1771544824"},{"product_id":"qbp890075","title":"Vimar Flush Consumer Unit, 12 Modules, IP40, Transparent Door","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Vimar VMV52412 is a flush-mount consumer unit mounting box with a vertically hinged transparent door, IP40 protection, and space for 12 modular devices on a single DIN rail. The enclosure measures 185 mm high, 285 mm wide, and 93 mm deep, with a built-in depth of 72 mm and an inner depth of 92 mm.\u003c\/p\u003e\u003cp\u003eOn a boat, this type of box is used to keep DIN-rail components tidy behind a clean door, so you can check switch and breaker positions without leaving the panel open. With an IP40 rating, it is meant for protected interior spaces where you want dust and accidental contact protection, not for lockers that see spray or washdowns.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eFlush-mounted enclosure for a cleaner, built-in look on bulkheads and interior panels\u003c\/li\u003e\n\u003cli\u003eCapacity for 12 modular spacings on 1 row\u003c\/li\u003e\n\u003cli\u003eVertically hinged transparent door so the inside stays visible when closed\u003c\/li\u003e\n\u003cli\u003eIP40 protection for interior installations where water exposure is not expected\u003c\/li\u003e\n\u003cli\u003eDIN rail included for mounting standard modular devices\u003c\/li\u003e\n\u003cli\u003eBuilt-in depth 72 mm with 92 mm inner depth for cable bending room and device clearance\u003c\/li\u003e\n\u003cli\u003eRAL 9003 white finish for a neutral, clean panel appearance\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis box is sized for one row of up to 12 modular DIN-rail devices. Before ordering, check that your mounting surface can accept a flush enclosure of this footprint and that you have enough recess depth behind the panel for the built-in section, plus clearance for wiring and the door to swing freely.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003ePlan cable entry so conductors can route cleanly to the DIN rail without sharp bends. Leaving a little service loop helps when you need to swap a module later. The transparent door is useful when the unit is mounted in an electrical locker or cabin panel where you want quick checks without exposing live components.\u003c\/p\u003e\u003ch6\u003eUse on board\u003c\/h6\u003e\u003cp\u003eThis enclosure is a good match for boats that need a flush-mounted distribution or control point using DIN-rail format components such as breakers, RCD devices, relays, or terminal blocks. It fits well in cabins, technical cabinets, and other dry, protected spaces where you want a neat finish and basic touch and dust protection.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eWipe the door and housing with a soft cloth to keep the viewing window clear. If the enclosure is installed in a vibration-prone area, periodically check that internal devices and wiring remain properly secured on the rail.\u003c\/p\u003e","brand":"Vimar","offers":[{"title":"Default Title","offer_id":52269607813301,"sku":"QBP890075","price":57.59,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1300590_qbp890075.jpg?v=1771544825"},{"product_id":"qbp890209","title":"Vimar 3-Module Flush-Mount Floor Turret, For Eikon\/Arké\/Plana\/Neve Devices, 120x120x60.5 mm, 3 Conduit Inlets, Metal, Includes Mounting Frame","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Vimar VMV54303 is a 3-module floor mounting box for Eikon, Arké, Plana, and Neve devices that installs on the V54903 floor box for a flush floor location.\u003c\/p\u003e\u003cp\u003eIt has a metal body with a 120 mm x 120 mm footprint and 60.5 mm depth, which helps when you are planning clearances under a sole or raised platform. Three conduit inlets make cable routing into the floor box cleaner and easier to service later.\u003c\/p\u003e\u003cp\u003eThis kind of hardware is a good match when you are building out a tidy switching or power point at floor level and you want the device mounting to stay rigid even with vibration and regular foot traffic.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e3-module capacity for Vimar Eikon, Arké, Plana, and Neve device families\u003c\/li\u003e\n\u003cli\u003eFlush floor installation when used on the V54903 floor box\u003c\/li\u003e\n\u003cli\u003eSupplied with a 3-module mounting frame\u003c\/li\u003e\n\u003cli\u003eThree conduit inlets for bringing cables into the floor box\u003c\/li\u003e\n\u003cli\u003eDimensions: 120 mm length, 120 mm width, 60.5 mm depth\u003c\/li\u003e\n\u003cli\u003eMetal construction with screw mounting method\u003c\/li\u003e\n\u003cli\u003eNo built-in strain relief, so cables should be secured as part of the install\u003c\/li\u003e\n\u003cli\u003eCE marking and WEEE compliance\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eWhat’s included\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eFloor mounting box\u003c\/li\u003e\n\u003cli\u003e3-module mounting frame\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis mounting box is meant for 3-module layouts using devices from the Eikon, Arké, Plana, and Neve families. Before cutting or committing to placement, confirm you are building a 3-module point and that your floor box is the V54903 so the parts line up correctly.\u003c\/p\u003e\u003cp\u003eBecause this is floor hardware, it is worth checking underside clearance for wiring bend radius, conduit runs, and any structure below the sole.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eThe unit mounts by screwing down to the floor box, and the three conduit inlets let you route incoming cables in a controlled way instead of relying on loose pass-throughs. Plan your cable paths so the device modules can be removed later without having to pull the whole run.\u003c\/p\u003e\u003cp\u003eSince there are no strain relieves built in, add your own cable support in the floor box or just outside it, especially in areas that see movement or vibration. Keeping wires supported reduces stress on terminals and helps prevent intermittent faults over time.\u003c\/p\u003e\u003ch6\u003eUse on board\u003c\/h6\u003e\u003cp\u003eCommon placements are cabin soles, helm areas, and workspaces where you want a clean switching point or a serviceable outlet location without adding a surface box. It also suits refits where existing Vimar device families are already used elsewhere on the boat and you want the same module format at floor level.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003ePeriodically check that mounting screws stay snug and that the wiring inside the box is still properly supported. If the floor area is exposed to wet gear or washdowns, keeping the opening clean and free of grit helps prevent wear on the installed modules.\u003c\/p\u003e","brand":"Vimar","offers":[{"title":"Default Title","offer_id":52269608173749,"sku":"QBP890209","price":105.69,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1300591_qbp890209.webp?v=1771544829"},{"product_id":"qbp890398","title":"Vimar Flush Mounting Box for Floor Box, 3-Module, Zinc-Plated Metal","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Vimar VMV54903 is a flush-mounting back box for a 3-module floor turret, used when you want power or data points to sit cleanly in the deck or cabin sole instead of on the surface.\u003c\/p\u003e\u003cp\u003eThe box is made from zinc-plated and painted metal and measures 100 x 100 x 60 mm, with 58 mm of usable depth. Fixing-screw spacing is 84 mm, and the floor installation is rated for loads up to 100 kg.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e3-module flush mounting box for floor turret installations in concrete floors\u003c\/li\u003e\n\u003cli\u003eZinc-plated and painted metal body with a closable plastic cover to keep debris out during building work\u003c\/li\u003e\n\u003cli\u003e100 x 100 x 60 mm overall size with 58 mm usable depth for routing and terminations\u003c\/li\u003e\n\u003cli\u003e84 mm fixing-screw spacing for matching compatible floor turret assemblies\u003c\/li\u003e\n\u003cli\u003eEarth continuity provision via earth connection screws\u003c\/li\u003e\n\u003cli\u003eRated for loads up to 100 kg when installed in the floor structure\u003c\/li\u003e\n\u003cli\u003eBuilt to IEC 60670-23 and EN 60670-23 requirements\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eWhat’s included\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eFlush mounting box\u003c\/li\u003e\n\u003cli\u003eClosable plastic cover\u003c\/li\u003e\n\u003cli\u003eEarth connection screws\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis box is used as the in-floor housing under Vimar 3-module floor turrets, including assemblies that mount on the V54903 footprint such as the V54303 floor turret. The 84 mm fixing-screw spacing is the key fit check when matching it to the turret body and mounting frame you plan to use.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eKeep the plastic cover fitted while the floor work is happening so cement, grit, and cuttings do not end up inside the box. If you plan to use the front entry holes for conduit, set the box 10 to 15 mm below finished floor level before the pour. Once the wiring is pulled, use the earth connection screws to maintain continuity through the floor assembly as required by your onboard electrical plan.\u003c\/p\u003e\u003ch6\u003eUse cases on board\u003c\/h6\u003e\u003cp\u003eThis is a good fit for clean, flush floor turret installs in interior areas that see foot traffic, like a salon, galley, wheelhouse, or accommodation spaces. For locations that get spray or routine washdowns, the matching floor turret and cover need to be suitable for that environment since the back box itself is an in-floor housing, not a sealed deck fitting.\u003c\/p\u003e","brand":"Vimar","offers":[{"title":"Default Title","offer_id":52269608566965,"sku":"QBP890398","price":8.97,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1300595_qbp890398.jpg?v=1771544833"},{"product_id":"qbp890543","title":"Vimar Surface-Mount Junction Box, IP44, 65 mm Dia, 35 mm Deep, 4 Cable Entries, 6pk","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Vimar VMV55001 is an IP44-rated surface-mount junction box for protecting wiring connections where you need splash protection and quick access for service.\u003c\/p\u003e\u003cp\u003eIt has a round body with a 65 mm diameter and 35 mm depth, which helps when you are fitting it behind panels or inside lockers where space is tight. The cover is a blind, snap-closed style, so you can open it for inspection without tools in most installations.\u003c\/p\u003e\u003cp\u003eFour trimmable step membrane inlets support conduit\/tube diameters of 20 mm or 25 mm. Rated insulation voltage (Ui) is 450 V, and the specified operating temperature range is 0°C to 60°C.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eIP44 protection level for locations exposed to dust and splashing water\u003c\/li\u003e\n\u003cli\u003eCompact footprint with a 65 mm diameter and 35 mm depth for confined mounting areas\u003c\/li\u003e\n\u003cli\u003eSurface mounting on walls or ceilings for straightforward retrofits and clean routing\u003c\/li\u003e\n\u003cli\u003eSnap-closed blind cover for fast access during troubleshooting and re-termination\u003c\/li\u003e\n\u003cli\u003eFour trimmable step membrane inlets to suit cable and conduit entry needs\u003c\/li\u003e\n\u003cli\u003eSupports 20 mm and 25 mm tube diameters for common marine conduit runs\u003c\/li\u003e\n\u003cli\u003eRAL 7035 grey finish for a neutral look inside technical spaces\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eMount the box on a flat surface where the cover can open fully and where the inlets can be oriented to keep water from pooling around cable entries. Trim each step membrane gradually so the cable or conduit passes through snugly, then keep bends gentle to avoid stressing terminations inside the box.\u003c\/p\u003e\u003cp\u003eBecause this is a junction box, plan enough slack to re-terminate in the future and leave room for connectors or terminal blocks you may be using inside. After wiring, confirm the cover is fully snapped closed around the entire perimeter.\u003c\/p\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis box is meant for surface mounting and routing smaller accessory wiring runs or control wiring where a protected splice point is needed. Conduit\/tube sizing is 20 mm or 25 mm, and the four entry points make it easier to bring in a feed and branch circuits without overcrowding a single side.\u003c\/p\u003e\u003cp\u003eWith an IP44 rating, it suits areas that see spray or condensation but are not subject to direct, sustained water exposure. For locations that can flood or take pressurized washdowns, use a higher protection level enclosure instead.\u003c\/p\u003e\u003ch6\u003eUse cases on board\u003c\/h6\u003e\u003cp\u003eCommon installs include behind a helm panel, inside a console, in a cockpit locker that stays mostly dry, or on an interior bulkhead where wiring transitions from a trunk line into smaller branches.\u003c\/p\u003e\u003cp\u003eThis is a good match for boat owners and installers who want a small junction point with splash protection and a clean surface-mount layout. It also fits refits where you are adding new accessories and need a tidy place to manage splices without opening up larger panels.\u003c\/p\u003e","brand":"Vimar","offers":[{"title":"Default Title","offer_id":52269608763573,"sku":"QBP890543","price":3.5,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1300600_qbp890543.jpg?v=1771544834"},{"product_id":"qbp890600","title":"Vimar Surface-Mount Junction Box, IP44, Round, 80 x 40 mm","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Vimar VMV55002 is a surface-mount IP44 junction box for protecting cable splices and small junctions in onboard electrical runs. It is an 80 mm diameter, 40 mm deep box with an overall outside envelope of 98 x 98 x 44 mm, which helps when you are fitting it behind liners, inside consoles, or under a hardtop.\u003c\/p\u003e\u003cp\u003eFour trimmable step-membrane entries handle cable or conduit runs sized for 20\/25 mm, and the housing is plastic in RAL 7035 grey. Rated insulation voltage (Ui) is 450 V and the working temperature range is 0 to 60 C.\u003c\/p\u003e\u003cp\u003eIP44 suits sheltered areas where you need protection from splashes and dripping water, not locations that see direct washdowns or standing water.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eIP44 degree of protection for sheltered marine installations exposed to splashes and drip\u003c\/li\u003e\n\u003cli\u003eSurface-mount format for wall or ceiling mounting inside cabins, lockers, and console voids\u003c\/li\u003e\n\u003cli\u003eFour cable entries with trimmable step-membrane feed-throughs for 20\/25 mm conduit runs\u003c\/li\u003e\n\u003cli\u003eNominal size 80 mm diameter x 40 mm deep, with an overall outside envelope of 98 x 98 x 44 mm\u003c\/li\u003e\n\u003cli\u003eRated insulation voltage (Ui) 450 V and working temperature range 0 to 60 C\u003c\/li\u003e\n\u003cli\u003eSolid cover (not transparent) to keep the wiring protected from knocks and snagging\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eMount the box on a flat bulkhead or overhead where you can still reach the cover for future checks. Trim only the membrane steps you need so the entry grips the cable or conduit closely, then route cables with a drip loop so water does not run straight toward the entry points.\u003c\/p\u003e\u003cp\u003eKeep terminations supported inside the box and avoid leaving tension on the conductors. On boats that see vibration and pounding, strain relief and neat cable dressing make a noticeable difference over time.\u003c\/p\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThe four entries are intended for conduit or tube runs in the 20\/25 mm range, which is common for small cable chases on boats. This size works well when you need an accessible junction point for lighting circuits, instrument feeds, and accessory wiring inside protected spaces.\u003c\/p\u003e\u003cp\u003eThe working temperature range is 0 to 60 C, so it is best placed away from consistently hot areas such as tight engine spaces without ventilation.\u003c\/p\u003e\u003ch6\u003eUse and protection on board\u003c\/h6\u003e\u003cp\u003eIP44 means it handles splashes and dripping water, but it is not a submersible enclosure. For cockpit soles, deck penetrations, and areas that get hose-downs, place it in a protected void or use an enclosure with a higher ingress rating.\u003c\/p\u003e\u003cp\u003eThis junction box is a good match for tidy refits and new installations where you want a compact enclosure that keeps junctions accessible without taking up much room.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eDuring seasonal checks, inspect the cover seating and the entry membranes for cuts or cracking. If you see salt buildup around the entries, clean the area and re-seat the wiring so the fit stays consistent.\u003c\/p\u003e","brand":"Vimar","offers":[{"title":"Default Title","offer_id":52269609058485,"sku":"QBP890600","price":4.27,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1300601_qbp890600.jpg?v=1771544835"},{"product_id":"qbp890913","title":"Vimar Surface-Mount Junction Box, IP44, 80 x 80 x 40 mm","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Vimar VMV55003 is an IP44 surface-mount junction box sized at 80 x 80 x 40 mm for enclosing wire joins and terminations where you want a clean, accessible handoff point.\u003c\/p\u003e\u003cp\u003eThe housing is plastic with a blind (non-transparent) cover in RAL 7035 grey. It is rated with Ui 450 V insulation voltage and a working temperature range of 0°C to 60°C, which suits typical onboard AC and DC wiring when installed in an appropriate, protected location.\u003c\/p\u003e\u003cp\u003eIP44 is a good match for sheltered areas that may see damp air or the occasional splash, but it is not meant for places that get steady hose-downs or any kind of immersion.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eIP44 protection for splash-prone, sheltered mounting locations.\u003c\/li\u003e\n\u003cli\u003e80 x 80 x 40 mm square, surface-mount format for compact junctions.\u003c\/li\u003e\n\u003cli\u003eSix cable entry points with trimmable step membranes for routing and strain relief.\u003c\/li\u003e\n\u003cli\u003eBlind, non-transparent cover to keep wiring out of sight while still allowing quick access for inspection.\u003c\/li\u003e\n\u003cli\u003ePlastic enclosure in RAL 7035 grey with Ui 450 V insulation rating and 0°C to 60°C operating range.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis box is intended for surface mounting on a flat bulkhead, panel, or overhead where you have room to bring cables in and still leave a gentle bend radius inside. If your run includes conduit or loom, plan the entry location so the lid can open without fighting the wiring.\u003c\/p\u003e\u003cp\u003eFor boats, it makes the most sense in dry lockers, behind helm panels, inside cabins, or under hardtops where spray is occasional rather than constant. For exposed deck areas or washdown zones, a higher IP-rated enclosure is usually the better call.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eMount it to a solid surface on the wall or ceiling, then trim the step membranes to suit the cable diameter so the entry stays snug. Leave enough slack for service, keep splices and connectors positioned so the cover closes without pinching, and support heavier cables nearby so they are not hanging off the entries.\u003c\/p\u003e\u003cp\u003eAs with any junction point on a boat, the enclosure is only part of the protection. Use marine-appropriate connectors, make clean terminations, and keep dissimilar metals out of contact where corrosion could start at the connection itself.\u003c\/p\u003e\u003ch6\u003eUse cases on board\u003c\/h6\u003e\u003cp\u003eThis style of junction box works well for splitting lighting circuits, grouping accessory feeds, or protecting a splice where a harness transitions through a bulkhead. It is also handy when you want a neat service point for troubleshooting without having loose connections floating behind a panel.\u003c\/p\u003e\u003cp\u003eIt is a good fit for owners and installers who want an organized, inspectable junction in a compact footprint, especially in interior spaces that see humidity, vibration, and occasional splashes.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eOpen the cover during routine checks and look for moisture, salt residue, or heat discoloration at the connectors. If the area tends to stay damp, drying it out early and improving cable support usually prevents repeat issues. Replace any compromised membranes or connectors so the enclosure keeps doing its job.\u003c\/p\u003e","brand":"Vimar","offers":[{"title":"Default Title","offer_id":52269609648309,"sku":"QBP890913","price":5.14,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1300602_qbp890913.jpg?v=1771544836"},{"product_id":"qbp891044","title":"Vimar IP55 Surface-Mount Junction Box, 100x100x50mm, 6 Inlets, RAL 7035 Grey","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Vimar VMV55104 is an IP55-rated surface-mount junction box for protecting wiring connections in areas exposed to spray, washdowns, and dust. It’s a practical choice when you need a sealed enclosure for cable splices on bulkheads, inside lockers, under consoles, or in other onboard spaces where wiring needs to stay contained and protected.\u003c\/p\u003e\u003cp\u003eThe housing is plastic in grey RAL 7035, with stainless steel screws, and it uses a blind cover secured by screws. Cable entry is handled through a trimmable step membrane so you can open the pass-through to match the cable route without leaving an oversized opening.\u003c\/p\u003e\u003cp\u003eOverall dimensions are 100 mm length, 128 mm width, and 56 mm depth. The unit is rated Ui 450 V and is specified for 0°C to 60°C operation.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eIP55 protection for dust and water jets, suited for exposed onboard areas where spray and washdowns happen\u003c\/li\u003e\n\u003cli\u003eSurface mounting for walls and ceilings, useful on bulkheads, inside consoles, and in equipment lockers\u003c\/li\u003e\n\u003cli\u003eBlind cover with screw attachment to keep wiring secured and inaccessible during normal use\u003c\/li\u003e\n\u003cli\u003eTrimmable step membrane cable entry to size the pass-through to the cable route\u003c\/li\u003e\n\u003cli\u003ePlastic enclosure in grey RAL 7035 with stainless steel screws for better longevity around moisture\u003c\/li\u003e\n\u003cli\u003eRated insulation voltage Ui 450 V and operating temperature range 0°C to 60°C\u003c\/li\u003e\n\u003cli\u003eDimensions: 100 mm (L) x 128 mm (W) x 56 mm (D)\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eMount the box to a solid, flat surface so the cover seats evenly and the seal can do its job. For boats, that usually means a bulkhead, console interior, cockpit locker wall, or a sheltered area in the engine room where it won’t be submerged.\u003c\/p\u003e\u003cp\u003eUse the step membrane to create cable entries that match your cable size and routing. Keep entries tidy and avoid forcing oversized cables through undersized openings, since that can compromise the fit around the pass-through.\u003c\/p\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis junction box is a good match when you need a compact surface box for joining circuits like deck accessories, lighting feeds, pumps, or sensors, and you want added protection from spray and dust. It’s also useful during refits when you’re cleaning up older splices and want them contained in a closed enclosure rather than left in open loom or taped joints.\u003c\/p\u003e\u003cp\u003eIP55 helps in wet environments, but it is not meant for full immersion. Choose a mounting spot that stays above standing water and where the cover can be accessed later for inspection or troubleshooting.\u003c\/p\u003e","brand":"Vimar","offers":[{"title":"Default Title","offer_id":52269609943221,"sku":"QBP891044","price":10.03,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1300603_qbp891044.jpg?v=1771544838"},{"product_id":"qbp891088","title":"Vimar Surface-Mount Junction Box, IP55, 120 x 80 x 50 mm, 6 Inlets","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Vimar VMV55105 is an IP55-rated surface-mount junction box sized 120 x 80 x 50 mm for protecting cable joins and terminals where spray, dust, and general deck-area grime can be a problem. It uses six cable entries with trimmable step membranes to suit 20 mm or 25 mm conduit or tubing, so you can route runs cleanly without leaving oversized openings.\u003c\/p\u003e\u003cp\u003eOn board, this is the kind of box you mount in a cockpit locker, under a hardtop, inside a lazarette, or anywhere you need a tidy, serviceable connection point that is not exposed to immersion. It is rated for 0 to 60 C operating temperatures and has a rated insulation voltage of 450 V, which fits typical low-voltage DC and AC wiring practices when installed to local electrical codes.\u003c\/p\u003e\u003cp\u003eIP55 helps with spray and washdowns, but it is not a sealed potting box for underwater or bilge submersion. Place it where it stays out of standing water, and keep cable runs supported so vibration does not work connections loose over time.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eIP55 degree of protection for use in damp, dusty, and splash-prone areas on a boat\u003c\/li\u003e\n\u003cli\u003e120 x 80 x 50 mm enclosure size for compact, surface-mounted installs\u003c\/li\u003e\n\u003cli\u003eSix inlets with trimmable step membranes for 20 mm or 25 mm conduit or tubing\u003c\/li\u003e\n\u003cli\u003eBlind cover with screwed attachment for secure closure during vibration and routine access\u003c\/li\u003e\n\u003cli\u003ePlastic housing in grey (RAL 7035) with stainless steel cover screws\u003c\/li\u003e\n\u003cli\u003eRated insulation voltage 450 V and working temperature range 0 to 60 C\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eMount the box to a solid, flat surface on the bulkhead or overhead where you can still reach it for future inspection. Bring conduits or tubes into the selected entries, trim the step membranes only as much as needed, and leave a drip loop on cables where practical so water does not track straight into the enclosure.\u003c\/p\u003e\u003cp\u003eFor a cleaner result in lockers and wet areas, route and secure cables first, then make terminations inside the box with enough slack for service. After closing, confirm the cover is evenly seated and the screws are snug so the sealing surfaces stay consistent.\u003c\/p\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis junction box is set up for 20 mm and 25 mm conduit or tubing through its step-membrane entries. If your installation uses different sizes, confirm your conduit system and cable routing plan before cutting any entries.\u003c\/p\u003e\u003cp\u003eThe rectangular footprint suits tight runs behind panels, inside deck lockers, and along wiring trunks where a compact surface box is easier to service than an in-line splice.\u003c\/p\u003e\u003ch6\u003eMaterials and corrosion resistance\u003c\/h6\u003e\u003cp\u003eThe body is plastic, which avoids paint blistering and metal corrosion in damp compartments. The cover uses stainless steel screws, which helps in a saltwater environment, but it is still worth rinsing salt residue from hardware during routine washdowns and keeping dissimilar metals separated at the mounting points.\u003c\/p\u003e\u003ch6\u003eUse cases on board\u003c\/h6\u003e\u003cp\u003eThis box makes sense for consolidating lighting branches, deck accessory feeds, locker circuits, or equipment terminations where you want a defined junction point instead of hidden splices. It is also a practical option when refitting wiring and you need a neat place to transition from conduit to a local device run.\u003c\/p\u003e\u003cp\u003eIt is a good match for owners and installers who want service access later, especially on boats that see regular spray, vibration, and periodic washdowns.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eOpen the box occasionally to check for moisture, loose terminations, and cable strain, especially after heavy weather or a season of vibration. Replace any entry membrane that has been cut too large or torn, and keep cable support points close enough that movement is not transferred into the enclosure.\u003c\/p\u003e","brand":"Vimar","offers":[{"title":"Default Title","offer_id":52269610205365,"sku":"QBP891088","price":11.31,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1300604_qbp891088.jpg?v=1771544839"},{"product_id":"qbp891403","title":"Vimar Surface-Mount IP55 Junction Box, 150x110x70mm, 20\/25mm Cable Entries, 10 Inlets","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Vimar VMV55106 is an IP55-rated surface-mount junction box sized 150 x 110 x 70 mm for protecting electrical splices and terminations in damp, splash-prone areas on a boat.\u003c\/p\u003e\u003cp\u003eThe enclosure is plastic with a grey RAL 7035 finish, and the cover closes with stainless steel screws. Cable entries use trimmable step membranes and suit 20 mm or 25 mm conduit, which helps keep runs neat and reduces cable movement where vibration is constant.\u003c\/p\u003e\u003cp\u003eThis box makes sense for deck and cockpit accessories, console wiring, and locker or lazarette circuits where you want connections enclosed and protected, but you are not installing in a space that can flood or remain submerged.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eIP55-rated enclosure for protection against dust and water spray\u003c\/li\u003e\n\u003cli\u003e150 x 110 x 70 mm surface-mount box for bulkhead or overhead installation\u003c\/li\u003e\n\u003cli\u003eUp to 10 cable entry points with trimmable step membranes\u003c\/li\u003e\n\u003cli\u003eEntry system sized for 20 mm and 25 mm conduit\u003c\/li\u003e\n\u003cli\u003eCover secured with stainless steel screws to hold tight in vibration-prone installs\u003c\/li\u003e\n\u003cli\u003eRated insulation voltage (Ui): 450 V\u003c\/li\u003e\n\u003cli\u003eWorking temperature range: 0 C to 60 C\u003c\/li\u003e\n\u003cli\u003eGrey RAL 7035 finish for a clean, low-contrast look in equipment spaces\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThe rectangular body is intended for surface mounting, so it works well when you do not have the depth for a recessed box. Plan space around the lid so it can be removed for inspection and future service, especially if the box is mounted under a hardtop or inside a console.\u003c\/p\u003e\u003cp\u003eThe conduit-friendly entries are useful when you are protecting cable runs through lockers, under gunwales, or along a bulkhead where chafe protection matters.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eMount the box on a flat surface and route cables so they approach from below or from the side when possible. Leave enough slack to open the cover without pulling on splices, and secure the cable run nearby so the entry points are not taking the full load of vibration.\u003c\/p\u003e\u003cp\u003eTrim only the membrane steps you need for the cable or conduit size being used. Keep outer jackets intact into the box so water does not track along conductors, and keep unused entries sealed.\u003c\/p\u003e\u003ch6\u003eElectrical and system integration\u003c\/h6\u003e\u003cp\u003eThis is a protective enclosure, not a terminal block by itself, so connection quality depends on the splices and terminations you install inside. Use tinned marine conductors and sealed connectors suited to your circuit, and keep connections positioned so the lid can close without pinching insulation.\u003c\/p\u003e\u003ch6\u003eMaintenance and checks\u003c\/h6\u003e\u003cp\u003eAfter the first few outings, check that the cover screws are snug and that the entry membranes still grip the cable or conduit cleanly. Any time the box is opened, wipe the sealing surfaces before closing it again so the IP55 protection is not compromised by grit or salt residue.\u003c\/p\u003e","brand":"Vimar","offers":[{"title":"Default Title","offer_id":52269610795189,"sku":"QBP891403","price":17.74,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1300605_qbp891403.jpg?v=1771544841"}],"url":"https:\/\/www.qualityboatparts.com\/collections\/mounting-boxes.oembed?page=3","provider":"Quality Boat Parts","version":"1.0","type":"link"}