{"title":"Lopolight","description":"","products":[{"product_id":"qbp995199","title":"Lopolight Tri-Color LED Navigation Light, 2NM, 10-32VDC, IP68 POM Base, Connector, Horizontal Mount","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Lopolight 201-005-B TB is a 2 NM tri-color LED navigation light for horizontal mounting with an IP68 POM base and connector. It runs on 10-32VDC, so it fits standard 12V and 24V onboard systems, and the compact body measures Ø92.5 mm x 36 mm (Ø3.6 in x 1.4 in).\u003c\/p\u003e\u003cp\u003eThe IP68 base is built for wet mastheads and washdowns, and it includes a cable gland sized for 4-14 mm cable so the entry stays sealed when you route wiring down a mast or through a hardtop. This light is DNV certified and approved to COLREG72, USCG, IEC 60945, and IACS E10 for navigation use.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eTri-color output (red, green, white) with a 2 NM rating for masthead-style navigation lighting\u003c\/li\u003e\n\u003cli\u003eWide-input 10-32VDC operation for 12V and 24V electrical systems\u003c\/li\u003e\n\u003cli\u003eIP68 POM base with connector and a cable gland for 4-14 mm cable\u003c\/li\u003e\n\u003cli\u003ePre-cabled with a 0.75 m shielded marine-grade cable for clean installation runs\u003c\/li\u003e\n\u003cli\u003eLow draw at 2.6 W, with current draw of 150 mA at 12VDC and 81 mA at 24VDC\u003c\/li\u003e\n\u003cli\u003eMinimum feed wire gauge of 0.5 mm² (AWG 22)\u003c\/li\u003e\n\u003cli\u003eOperating temperature range of -25°C to 55°C for cold starts and hot deck hardware\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eWhat’s included\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eNavigation light assembly, pre-cabled with 0.75 m shielded marine-grade cable\u003c\/li\u003e\n\u003cli\u003eInstallation guide\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eThis light mounts on a flat horizontal surface. On sailboats it is commonly installed at the masthead, where the tri-color format is used in place of separate sidelights and a stern light when that configuration is allowed for the vessel and operating mode.\u003c\/p\u003e\u003cp\u003ePlan the cable run so the pre-attached lead reaches a dry junction point inside the mast, under a deck gland, or inside a radar arch. Power it from a protected DC circuit within the 10-32VDC range, then verify the light’s orientation so the sectors align correctly with the vessel centerline.\u003c\/p\u003e\u003ch6\u003eMaterials and sealing\u003c\/h6\u003e\u003cp\u003eThe housing uses anodized aluminum (25µ) with a PMMA lens and A4 stainless steel screws for hardware that holds up well in saltwater. Sealing compounds include epoxy and polyurethane, and the IP68 base helps keep spray and standing water out at the mounting point.\u003c\/p\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis unit is a good match for owners who want a compact tri-color light with a sealed base connection for service access at the mount. It suits boats where space at the masthead or mounting pad is limited, but you still want a clear, standards-compliant navigation signal with modest power draw.\u003c\/p\u003e\u003cp\u003eBefore ordering, confirm you have a horizontal mounting surface with clearance for the Ø92.5 mm footprint and space to dress the cable through the gland. Also check that your existing wiring plan can meet the minimum 0.5 mm² (AWG 22) feed requirement and that the circuit voltage stays within 10-32VDC.\u003c\/p\u003e","brand":"Lopolight","offers":[{"title":"Default Title","offer_id":52268889243829,"sku":"QBP995199","price":651.16,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1301277_qbp995199.png?v=1771540653"},{"product_id":"qbp785068","title":"Lopolight 201-010 Masthead Light, White Light, 2nm, Vertical Mount, 10-32VDC, IP68, Black Housing","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Lopolight 201-010-B is a white masthead (steaming) navigation light with a 225° beam and 2 nautical mile visibility, built for vertical mounting on boats up to 12 m (39.4 ft).\u003c\/p\u003e\u003cp\u003eIt runs on 10-32 VDC for 12V and 24V systems and uses LED output for low current draw. The housing is sealed to an IP68 rating and comes in a black finish for installs where glare control and a low-profile look matter on the mast or cabin structure.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e2 NM masthead light with a 225° white beam for power-driven vessels under way\u003c\/li\u003e\n\u003cli\u003eFor vessels up to 12 m (39.4 ft)\u003c\/li\u003e\n\u003cli\u003e10-32 VDC input for 12V and 24V electrical systems\u003c\/li\u003e\n\u003cli\u003eIP68 sealing for heavy weather, washdowns, and exposed mast installations\u003c\/li\u003e\n\u003cli\u003eBlack anodized aluminum housing with potted internals for water and vibration resistance\u003c\/li\u003e\n\u003cli\u003eShort lead for clean installs: 2.3 ft (0.7 m) cable with rear exit\u003c\/li\u003e\n\u003cli\u003eMeets COLREG72 and EN14744 requirements and is recognized for USCG use; IEC 60945 listed\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis is a masthead (steaming) light, meaning it is the forward-facing white light used when a power-driven vessel is under way. The 225° beam pattern is intended for mounting on a vertical surface so the light projects forward with the correct sector.\u003c\/p\u003e\u003ch6\u003eInstallation and wiring\u003c\/h6\u003e\u003cp\u003eThe vertical-mount body suits mast faces, bulkheads, and other flat vertical surfaces where you can keep the light square and unobstructed. With a 0.7 m lead, most installs route the cable into the structure and make the long run from a protected splice point or junction inside the mast or cabin top, keeping connections out of direct spray.\u003c\/p\u003e\u003ch6\u003eMaterials and sealing\u003c\/h6\u003e\u003cp\u003eThe light uses a precision-machined anodized aluminum housing and a PMMA light guide. The electronics are sealed and potted, which helps when the light lives in the vibration and constant exposure that comes with mast and hardtop mounting.\u003c\/p\u003e\u003ch6\u003eUse on board\u003c\/h6\u003e\u003cp\u003eThis is a good match for small powerboats and sailboats up to 12 m that need a compact masthead light for coastal cruising, night runs, and early-morning departures. It also makes sense on boats that see frequent saltwater spray and want an IP68-rated fixture rather than a lightly sealed housing.\u003c\/p\u003e\u003ch6\u003eWhat’s included\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eNavigation light with attached 2.3 ft (0.7 m) cable\u003c\/li\u003e\n\u003cli\u003eMounting hardware\u003c\/li\u003e\n\u003cli\u003eInstallation guide\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Lopolight","offers":[{"title":"Default Title","offer_id":52268889833653,"sku":"QBP785068","price":498.32,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1298133_qbp785068.jpg?v=1771540654"},{"product_id":"qbp746869","title":"Lopolight Horizontal Mount Double Masthead Light, 5NM, 20-32VDC","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Lopolight 300-038 is a white double masthead navigation light with a 225° sector and a 5 NM rating, for 20-32 VDC systems and horizontal mounting on vessels from 20 to 50 m (65.5 to 164 ft). It draws 7 W and lists 290 mA at 24 VDC, which lines up with a 24 V onboard electrical system.\u003c\/p\u003e\u003cp\u003eThe housing is silver anodized aluminum with a PMMA lens and A4 stainless steel fasteners. IP68 sealing keeps water and dust out, and the unit is rated for -25°C to 55°C operation. Overall size is Ø92.5 mm x 128 mm and weight is 1.65 kg (58.2 oz).\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eWhite 225° masthead sector with a 5 NM visibility rating\u003c\/li\u003e\n\u003cli\u003e20-32 VDC input, 7 W draw, 290 mA at 24 VDC\u003c\/li\u003e\n\u003cli\u003eIP68 sealing for exposed mounting and washdowns\u003c\/li\u003e\n\u003cli\u003eHorizontal mount form factor with Ø92.5 mm x 128 mm overall dimensions\u003c\/li\u003e\n\u003cli\u003eSilver anodized aluminum housing (25 micron anodizing) with PMMA lens and A4 stainless steel fasteners\u003c\/li\u003e\n\u003cli\u003ePlug connector connection for straightforward service and removal\u003c\/li\u003e\n\u003cli\u003eOperating temperature range: -25°C to 55°C\u003c\/li\u003e\n\u003cli\u003eApprovals: COLREG72, EN14744, IEC 60945, IACS E10, USCG, ABS, M.E.D., DNV, LR\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eMount the light horizontally in the correct masthead position with clear sightlines. Cable routing can be run out the side or down, which helps when you are feeding wiring through a mast, radar arch, or hardtop.\u003c\/p\u003e\u003cp\u003eThe connection is via plug connector, so leave enough access to reach the plug during service. Minimum feed wire gauge is 0.5 mm2 (AWG 22). Use cable glands sized for 7-13 mm cable diameter to keep the cable entry watertight and strain-relieved.\u003c\/p\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis model is for 20-32 VDC only and will not operate on a 12 V circuit. It is intended for vessels in the 20-50 m size range and is built around a 225° masthead light sector with a 5 NM rating.\u003c\/p\u003e\u003ch6\u003eUse cases on board\u003c\/h6\u003e\u003cp\u003eA good match for yachts and larger sportfish running a 24 V system that need a 5 NM masthead light in a stacked format. It also suits refits where a sealed, plug-connected light makes future removal and inspection less disruptive to the wiring run.\u003c\/p\u003e\u003ch6\u003eWhat’s included\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eNavigation light with plug connector\u003c\/li\u003e\n\u003cli\u003eMounting hardware\u003c\/li\u003e\n\u003cli\u003eHDPE base plate\u003c\/li\u003e\n\u003cli\u003eCable glands for 7-13 mm cable diameter\u003c\/li\u003e\n\u003cli\u003eInstallation guide\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Lopolight","offers":[{"title":"Default Title","offer_id":52268890194101,"sku":"QBP746869","price":3244.34,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1298129_qbp746869.jpg?v=1771540657"},{"product_id":"qbp101185","title":"Lopolight Circular Baseplate, For Horizontal Mount Lights, HDPE","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Lopolight 400-404 is a circular HDPE baseplate that sits between a Lopolight horizontal mount light and the mounting surface. It keeps the light housing from touching metal directly, which helps reduce galvanic corrosion marks and surface wear when the fixture is installed on aluminum, stainless, or painted steel.\u003c\/p\u003e\u003cp\u003eThis is a non-electrical accessory with 0 mA current draw on both 12VDC and 24VDC systems, and it weighs 2.47 oz (0.07 kg). The light itself is sold separately.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eHDPE (high density polyethylene) isolation baseplate for Lopolight horizontal mount lights\u003c\/li\u003e\n\u003cli\u003eBreaks direct contact between an aluminum light housing and a metal mounting surface\u003c\/li\u003e\n\u003cli\u003e0 mA current draw at 12VDC and 24VDC\u003c\/li\u003e\n\u003cli\u003eLightweight at 2.47 oz (0.07 kg)\u003c\/li\u003e\n\u003cli\u003eHelps when mounting a horizontal light to a metal hardtop, arch, mast plate, or similar structure\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eUse this baseplate with Lopolight horizontal mounted lights that call for a circular PE\/HDPE spacer under the light. It does not affect wiring or electrical loading; it simply adds an insulating layer between the fixture and the boat.\u003c\/p\u003e\u003cp\u003eIf your installation uses a separate mounting base or adapter, confirm the baseplate is part of your intended stack-up so fastener length and seating stay correct.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eDry-fit the baseplate at the mounting location, line up the fastener pattern, and make sure the surface is flat so the light sits evenly. If you bed the assembly, keep fastener holes sealed and avoid trapping water under the light.\u003c\/p\u003e\u003cp\u003eTighten fasteners evenly so the HDPE plate is compressed uniformly, then recheck after the first few runs for any settling.\u003c\/p\u003e\u003ch6\u003eUse on board\u003c\/h6\u003e\u003cp\u003eThis is a good match for refits where a horizontal mount navigation light is moving onto a metal structure, or when corrosion staining shows up around the base from dissimilar-metal contact. It also helps on boats that see heavy vibration, where metal-to-metal rubbing can scuff finishes over time.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eRinse with fresh water during routine washdowns and inspect the mounting area during seasonal checks. If the plate shows deep grooves or deformation from over-tightening, replace it to keep the light properly isolated.\u003c\/p\u003e","brand":"Lopolight","offers":[{"title":"Default Title","offer_id":52268890521781,"sku":"QBP101185","price":61.05,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1298131_qbp101185.png?v=1771540658"},{"product_id":"qbp839045","title":"Lopolight 30W Deck\/Spreader Light, 26 Deg Reflector, 10-32VDC, IP68","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Lopolight 400-080-26 is a 30W deck\/spreader light that puts out white light through a 26° reflector and runs on 20 to 32 VDC power. It is dimmable and sealed to IP68, which suits it for exposed mounting where spray, washdowns, and vibration are part of normal life on board.\u003c\/p\u003e\u003cp\u003eThe focused 26° beam is useful when you want reach and definition instead of a wide flood, such as lighting the foredeck from a hardtop, picking out the working area around mast spreaders, or adding controlled light to a cockpit or bow work zone without blasting the whole boat.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e20 to 32 VDC input for 24V systems; current consumption is 1150 mA at 24 VDC\u003c\/li\u003e\n\u003cli\u003e26° reflector for a tighter beam that carries down the deck or out from the rig\u003c\/li\u003e\n\u003cli\u003eDimmable output for night operations and close-quarters work\u003c\/li\u003e\n\u003cli\u003eIP68-rated sealing for wet installations and routine washdowns\u003c\/li\u003e\n\u003cli\u003eSilver anodized aluminum housing with 25µ anodizing, PMMA lens, and A4 stainless steel fasteners\u003c\/li\u003e\n\u003cli\u003eCompact size (about 89 x 55 mm) with a listed weight of 0.7 kg\u003c\/li\u003e\n\u003cli\u003eOperating temperature range of -25°C to 55°C\u003c\/li\u003e\n\u003cli\u003e0.7 m attached cable; minimum feed wire gauge listed as 0.5 mm2 (22 AWG)\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and wiring\u003c\/h6\u003e\u003cp\u003ePlan this light for a 24V DC boat system within the 20 to 32 VDC range. The attached 0.7 m cable is meant to get you from the light body to a protected connection point, so most installs will involve extending the run with properly sized conductors, sealed connectors, and strain relief where the cable enters the structure.\u003c\/p\u003e\u003cp\u003eBecause it is dimmable, route wiring so the control gear is accessible and protected from direct spray. Use appropriate circuit protection for the branch circuit and follow your vessel’s electrical standards for terminations and drip loops.\u003c\/p\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eCheck the mounting area for clearance using the listed 89 x 55 mm body size, and confirm the beam path before drilling so the 26° pattern lands where you actually work. This style of focused spreader\/deck light is often placed higher to take advantage of throw, then dimmed down when you are alongside or working close in.\u003c\/p\u003e\u003ch6\u003eWhat’s included\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eDeck\/spreader light with attached cable\u003c\/li\u003e\n\u003cli\u003eMounting hardware\u003c\/li\u003e\n\u003cli\u003eInstallation guide\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Lopolight","offers":[{"title":"Default Title","offer_id":52268893667509,"sku":"QBP839045","price":1612.15,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1298138_qbp839045.jpg?v=1771540678"},{"product_id":"qbp207973","title":"Lopolight Circular Baseplate, For Horizontal Mount Navigation Lights, 130mm Dia x 14mm, Silver Anodized Aluminum, Includes Mounting Hardware","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Lopolight 400-401 is a 130 mm circular baseplate for horizontal mounting of Lopolight navigation lights. It has a 14 mm profile and weighs 11.99 oz (0.34 kg), giving you a stable mounting surface without adding much height.\u003c\/p\u003e\u003cp\u003eThe plate is silver anodized aluminum and uses A4 stainless steel hardware with nylon insulating shoulder bushings. It is built to let the light be fastened from above, which helps on hardtops, radar arches, and other places where underside access is limited.\u003c\/p\u003e\u003cp\u003eThis is a practical replacement when an existing base is worn, damaged, or corroded, and you want to keep your current Lopolight horizontal light setup in place while refreshing the mounting interface.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eHorizontal mount baseplate with a 130 mm diameter and 14 mm thickness\u003c\/li\u003e\n\u003cli\u003eWeight: 11.99 oz (0.34 kg)\u003c\/li\u003e\n\u003cli\u003eSilver anodized finish (EN ISO 7599)\u003c\/li\u003e\n\u003cli\u003eCompatible with bases 400-034, 400-035, and 400-037\u003c\/li\u003e\n\u003cli\u003eNylon shoulder bushings help isolate the fasteners from the aluminum plate\u003c\/li\u003e\n\u003cli\u003eA4 stainless steel hardware for attaching the light to the baseplate\u003c\/li\u003e\n\u003cli\u003eMount-from-above approach for easier service when you cannot reach the underside\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eWhat’s included\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eCircular aluminum baseplate (silver anodized)\u003c\/li\u003e\n\u003cli\u003e6 nylon shoulder bushings\u003c\/li\u003e\n\u003cli\u003e3 stainless steel M6 cap screws\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003ePlan the location so the navigation light has clear sight lines and the 130 mm footprint sits on a flat, supported surface. The supplied hardware is for attaching the light to the baseplate; fasteners for securing the baseplate to the vessel are selected to suit your mounting surface and backing method.\u003c\/p\u003e\u003cp\u003eOn cored or exposed-deck areas, sealing the fastener holes and bedding the baseplate helps keep moisture out. After tightening, re-check the mount after the first few runs, especially if the light is installed on a structure that sees vibration.\u003c\/p\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis baseplate is intended for Lopolight horizontal mounted lights using the matching promount bases. Confirm your existing base reference (400-034, 400-035, or 400-037) and verify you have room for the full 130 mm diameter before drilling or re-bolting.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eRinse with fresh water after saltwater use and wipe down with mild soap as needed. Avoid harsh abrasives that can wear the anodized surface, and keep the nylon bushings seated properly during service to maintain electrical isolation at the fasteners.\u003c\/p\u003e","brand":"Lopolight","offers":[{"title":"Default Title","offer_id":52268893864117,"sku":"QBP207973","price":144.48,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1298139_qbp207973.png?v=1771540680"},{"product_id":"qbp587161","title":"Lopolight Circular Baseplate for Horizontal Mount Navigation Lights, Aluminum, Black Anodized, Includes 3x M6 x 14 Screws.","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Lopolight 400-401-B is a circular aluminum baseplate for Lopolight horizontal-mount navigation lights, finished in black. It measures 130 mm across and weighs about 11.99 oz (0.34 kg), so it adds a solid footprint without adding much weight up high.\u003c\/p\u003e\u003cp\u003eThis is a replacement baseplate meant for repairs and refits where the original baseplate is worn, damaged, or you want a clean mounting surface again. The light itself is not included.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eCircular 130 mm baseplate for Lopolight horizontal-mounted navigation lights\u003c\/li\u003e\n\u003cli\u003eAluminum construction with a black finish for a tidy look on a cabin top, hardtop, or radar arch\u003c\/li\u003e\n\u003cli\u003eCan be used with Lopolight bases 400-034, 400-035, and 400-037\u003c\/li\u003e\n\u003cli\u003eNo wiring or voltage considerations since it is a mechanical mounting accessory\u003c\/li\u003e\n\u003cli\u003eLightweight at about 11.99 oz (0.34 kg) for easier handling during installation\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis baseplate is intended for Lopolight horizontal mounted lights. Before drilling or sealing anything, confirm you have enough flat surface area for a 130 mm base and that the mounting holes line up with your existing light base and cable routing.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eInstallation is a straightforward swap: remove the light and old baseplate (if installed), clean the mounting surface, position the new baseplate, then fasten it down evenly. Any deck or hardtop penetrations should be sealed appropriately for your mounting location to keep water out of the core.\u003c\/p\u003e\u003ch6\u003eMaterials and corrosion resistance\u003c\/h6\u003e\u003cp\u003eAluminum hardware on a boat benefits from basic corrosion prevention, especially in saltwater. When mounting against stainless fasteners or dissimilar metals, simple isolation steps like suitable bedding and insulating washers help reduce galvanic staining over time.\u003c\/p\u003e\u003ch6\u003eWhat’s included\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eCircular baseplate\u003c\/li\u003e\n\u003cli\u003e3 x M6x14 mounting screws\u003c\/li\u003e\n\u003cli\u003eInstruction manual\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eUse cases on board\u003c\/h6\u003e\u003cp\u003eThis baseplate makes sense for owners keeping spare parts aboard, yards doing navigation light replacements, and anyone reworking the mounting area for a horizontal light on a cabin top, hardtop, or arch where you want the light to sit flat and stay properly secured.\u003c\/p\u003e","brand":"Lopolight","offers":[{"title":"Default Title","offer_id":52268893929653,"sku":"QBP587161","price":144.48,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1298141_qbp587161.png?v=1771540683"},{"product_id":"qbp819149","title":"Lopolight Series 300-136 Masthead \u0026 Navigation Combo Light, For Vessels over 50m, 6 NM 225 deg Masthead, 3 NM 360 deg White Light, 20-32VDC, IP68, Horizontal Mount, Plug Connector, Silver Anodized Aluminum","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Lopolight 300-136+112G2 is a combined navigation light that puts a 6 NM 225° masthead light and a 3 NM 360° all-round white light into one horizontal-mount fixture. It runs on 20 to 32 VDC and draws 13 W, which lines up well with 24 VDC onboard systems.\u003c\/p\u003e\u003cp\u003eThis unit is specified for vessels over 50 m (164 ft) and is typically used where you need the masthead sector and an all-round white light from a single mounting position. The housing measures 92.5 mm in diameter by 129 mm high (3.6 in x 5 in) and weighs 2 kg (70.54 oz), so plan for a solid mounting surface.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eCombined output: 6 NM 225° masthead light plus 3 NM 360° all-round white light\u003c\/li\u003e\n\u003cli\u003e20 to 32 VDC input for 24 VDC electrical systems\u003c\/li\u003e\n\u003cli\u003e13 W power draw with 580 mA current consumption at 24 VDC\u003c\/li\u003e\n\u003cli\u003eIP68-rated enclosure for heavy spray, washdowns, and wet mounting locations\u003c\/li\u003e\n\u003cli\u003eSilver anodized aluminum housing with a PMMA lens and A4 stainless steel screws\u003c\/li\u003e\n\u003cli\u003ePlug connector for a clean install and easier service work\u003c\/li\u003e\n\u003cli\u003eOperating temperature range from -25°C to 55°C\u003c\/li\u003e\n\u003cli\u003eApproved to COLREG72 and EN14744 and carries USCG approval\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis is a horizontal-mount light, so it’s meant for a flat mounting face where the fixture can be leveled and aligned to keep the 225° masthead sector and the 360° all-round light unobstructed. On larger yachts and commercial vessels, that usually means a mast platform, wheelhouse top, or a purpose-built light bar where rigging and antennas will not cut into the arcs.\u003c\/p\u003e\u003cp\u003eElectrical fit is straightforward for 24 VDC boats, but confirm the circuit stays within the 20 to 32 VDC range under charge. Minimum feed wire gauge is 0.5 mm² (22 AWG); longer runs on tall masts may call for heavier wire to keep voltage drop in check.\u003c\/p\u003e\u003ch6\u003eInstallation and wiring\u003c\/h6\u003e\u003cp\u003eMount the light securely and verify orientation before final tightening, since small alignment errors can matter when you’re trying to keep sectors clean on a working mast. The plug connector helps keep the connection consistent and makes it simpler to remove the unit for service without disturbing the wiring run.\u003c\/p\u003e\u003cp\u003eAs with any nav light on a larger vessel, keep the cable route supported against vibration and protect the connector area from standing water. After installation, do a nighttime check underway or at the dock to confirm there are no shadows from hardware or superstructure.\u003c\/p\u003e\u003ch6\u003eMaterials and corrosion resistance\u003c\/h6\u003e\u003cp\u003eThe anodized aluminum housing and stainless fasteners handle typical topside exposure, including salt spray and sun. A quick rinse after offshore runs helps keep salt crystals from building around fasteners and the lens edge, especially if the light is mounted where washdowns hit it directly.\u003c\/p\u003e\u003ch6\u003eWhat’s included\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eMasthead\/navigation light with plug connector\u003c\/li\u003e\n\u003cli\u003eMounting hardware\u003c\/li\u003e\n\u003cli\u003eInstallation guide\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Lopolight","offers":[{"title":"Default Title","offer_id":52268894257333,"sku":"QBP819149","price":3855.28,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1298143_qbp819149.jpg?v=1771540684"},{"product_id":"qbp909348","title":"Lopolight X01 Vertical Sidelight Mounting Plate, Silver Anodized","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Lopolight 401-017 is a silver anodized aluminum mounting plate for Lopolight X01 series vertical sidelights. It gives the light a clean mounting surface and a solid base so the fixture sits straight on the vessel side.\u003c\/p\u003e\u003cp\u003eThis is a mechanical accessory with no electrical load, drawing 0 mA at both 12 VDC and 24 VDC. At 0.1 kg (3.53 oz), it is easy to handle during a refit while still providing a stable mounting point once fastened down.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eMade to mount Lopolight X01 series vertical sidelights\u003c\/li\u003e\n\u003cli\u003eSilver anodized aluminum plate for a clean finish on exposed installations\u003c\/li\u003e\n\u003cli\u003eUses A4 stainless steel screws for hardware that holds up in saltwater environments\u003c\/li\u003e\n\u003cli\u003eSupports vertical mounting orientation for X01 vertical sidelight applications\u003c\/li\u003e\n\u003cli\u003eNo power draw from the accessory: 0 mA at 12 VDC and 24 VDC\u003c\/li\u003e\n\u003cli\u003eLightweight component at 0.1 kg (3.53 oz)\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis plate is intended for the X01 series vertical sidelight form factor. Confirm the light you are mounting is the X01 vertical sidelight version, since Lopolight housings and bases vary by series and mounting style.\u003c\/p\u003e\u003cp\u003eIt is a mounting plate only. It does not replace the light, lens, or wiring, and it does not change your vessel voltage or lighting circuit requirements.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eDry-fit the plate and the sidelight first to confirm the final orientation and cable routing before drilling or bedding. Use a marine bedding compound under the plate and around fastener holes to help keep water out of the core or structure.\u003c\/p\u003e\u003cp\u003eTighten fasteners evenly so the plate seats flat and the light body remains aligned. After installation, recheck fastener tightness after the first few trips, especially on planing hulls or any boat that sees a lot of vibration.\u003c\/p\u003e\u003ch6\u003eMaterials and corrosion resistance\u003c\/h6\u003e\u003cp\u003eThe anodized aluminum plate and A4 stainless hardware are suited to exposed mounting locations where washdowns and salt spray are normal. Rinsing the area with fresh water after heavy salt exposure helps keep the finish looking clean over time.\u003c\/p\u003e\u003ch6\u003eUse on board\u003c\/h6\u003e\u003cp\u003eThis is a good match for owners replacing a damaged mounting plate, tidying up a previous install, or moving an X01 vertical sidelight to a new location during a refit. It also works well when you want the mounting hardware to blend in with other silver-finished fittings on the cabin side or superstructure.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eWash with fresh water and mild boat soap. Avoid aggressive abrasives that can dull the anodized finish. During routine navigation light checks, inspect the plate and fasteners for looseness and address any bedding gaps that could let water track into the mounting holes.\u003c\/p\u003e","brand":"Lopolight","offers":[{"title":"Default Title","offer_id":52268894290101,"sku":"QBP909348","price":87.39,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1298145_qbp909348.png?v=1771540686"},{"product_id":"qbp986401","title":"Lopolight X01 Series Vertical Sidelight Mounting Plate, Black Anodized Aluminum, A4 Stainless Screws","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Lopolight 401-017-B is a mounting plate for Lopolight X01 series vertical sidelights when you want a vertical install that sits flat and keeps the light stable.\u003c\/p\u003e\u003cp\u003eIt is made from black anodized aluminum with a 25µ anodizing layer and weighs about 0.1 kg (3.53 oz). This is a mechanical mounting part with no electrical connections and draws 0 mA on 12 VDC or 24 VDC systems.\u003c\/p\u003e\u003cp\u003eIt is commonly used during new installs and refits on cabin sides, pilothouse wings, hardtops, arches, and other vertical faces where a purpose-built plate makes alignment easier.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eCompatible with Lopolight X01 series vertical sidelights for vertical mounting locations\u003c\/li\u003e\n\u003cli\u003eBlack anodized aluminum with 25µ anodizing for a finish that holds up in exposed marine installations\u003c\/li\u003e\n\u003cli\u003eMaterial set includes A4 stainless steel screws alongside the anodized aluminum plate\u003c\/li\u003e\n\u003cli\u003e0 mA current consumption at 12 VDC and 24 VDC (mounting hardware only)\u003c\/li\u003e\n\u003cli\u003eApproximate weight: 0.1 kg (3.53 oz)\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis plate is for the X01 series vertical sidelights. Confirm your sidelight is the vertical version in the X01 range before ordering, since other mounting styles and series use different bases.\u003c\/p\u003e\u003cp\u003eIt suits all vessel sizes and works well where the mounting surface is curved or uneven and you want a consistent mounting face for the light.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eDry fit the plate, mark the fastener holes, and bed it properly to keep water out of the structure. Once the plate is secured, attach the sidelight and check alignment so the light sits square to the boat and maintains the correct viewing sectors.\u003c\/p\u003e\u003cp\u003eSince the plate does not draw power, there is no wiring to it. Route the sidelight cable with chafe protection and strain relief where it passes through the mounting surface.\u003c\/p\u003e\u003ch6\u003eUse on board\u003c\/h6\u003e\u003cp\u003eThis part is a practical choice for skippers and installers fitting X01 vertical sidelights on a refit, or moving sidelights to a cleaner vertical mounting position on a cruising boat, sportfisher, or workboat.\u003c\/p\u003e","brand":"Lopolight","offers":[{"title":"Default Title","offer_id":52268894486709,"sku":"QBP986401","price":81.39,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1298146_qbp986401.png?v=1771540687"},{"product_id":"qbp541717","title":"Lopolight Series 201-011 LED Masthead Light, 3NM, Vertical Mount, 10-32VDC, IP68, 15m Cable","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Lopolight 201-011-15M is a white masthead navigation light with a 225° sector and 3 NM visibility, supplied for vertical mounting with a 15 m cable. It runs on 10-32V DC and draws 3 W (232 mA at 12VDC, 127 mA at 24VDC), so it works on standard 12V and 24V onboard systems.\u003c\/p\u003e\u003cp\u003eThe housing measures 74.55 x 28 x 73.16 mm (2.9 x 1.1 x 2.88 in) and is sealed to an IP68 rating for exposed mounting locations. It is rated for vessels 12-20 m and approved to COLREG72, EN14744, IEC 60945, IACS E10, and USCG.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e3 NM white masthead light with a 225° sector and \u0026gt;15 cd intensity\u003c\/li\u003e\n\u003cli\u003e10-32V DC input for 12V or 24V systems\u003c\/li\u003e\n\u003cli\u003e3 W draw (232 mA @ 12VDC, 127 mA @ 24VDC)\u003c\/li\u003e\n\u003cli\u003eIP68 rating for spray, rain, and washdowns at the masthead\u003c\/li\u003e\n\u003cli\u003eSilver anodized aluminum (25 µ) body with a PMMA lens and A4 stainless mounting screws\u003c\/li\u003e\n\u003cli\u003eVertical mount format with a 15 m cable for long runs down a mast or through a hardtop\u003c\/li\u003e\n\u003cli\u003eOperating temperature range of -25°C to 55°C\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eWhat's included\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eNavigation light with 15 m cable\u003c\/li\u003e\n\u003cli\u003e2 mounting screws (M6 x 8 mm)\u003c\/li\u003e\n\u003cli\u003eInstallation guide\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis is a masthead (steaming) light that needs a clear forward-facing 225° arc. Install it on the vessel centerline and keep antennas, wind instruments, and rigging out of the light sector so the beam is not shadowed.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eMount vertically using the supplied M6 fasteners on a flat surface. Route the cable with strain relief at the light and a drip loop before the cable enters the mast or cabin, then protect the run at mast exits and deck glands to avoid chafe from vibration.\u003c\/p\u003e\u003ch6\u003eElectrical and system integration\u003c\/h6\u003e\u003cp\u003eWire it into a 10-32V DC navigation-light circuit controlled by your switch panel or lighting controller. The recommended minimum feed wire size is 0.5 mm² (AWG 22), and the circuit should be protected with an appropriately sized fuse or breaker for the load and the cable run.\u003c\/p\u003e\u003ch6\u003eMaterials and sealing\u003c\/h6\u003e\u003cp\u003eThe body uses silver anodized aluminum with a PMMA lens and A4 stainless hardware to suit saltwater exposure. The IP68 seal and operating range from -25°C to 55°C help it stay stable through cold starts, hot sun, and regular washdowns.\u003c\/p\u003e\u003ch6\u003eUse on board\u003c\/h6\u003e\u003cp\u003eThis light fits powerboats and motorsailers in the 12-20 m range that need a certified 3 NM masthead light, especially when the wiring run from the masthead to the distribution point is long. It also suits refits where the existing cable chase is tight and a pre-attached 15 m lead simplifies routing.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eRinse salt off the lens and housing during routine washdowns and keep the lens clear of dried salt film. At least once a season, inspect the cable where it passes through glands and mast exits, and re-seal any penetrations if you see moisture tracking.\u003c\/p\u003e","brand":"Lopolight","offers":[{"title":"Default Title","offer_id":52268924207285,"sku":"QBP541717","price":975.48,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1301275_qbp541717.png?v=1771540859"},{"product_id":"qbp325368","title":"Lopolight Pro-Mount Aluminum Mounting Base, For K-Lock Lights, 2CS+2CD, IP68, Horizontal Mount, 3.6 in Dia x 1.8 in, Silver Anodized Finish","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Lopolight 400-034 is an aluminum Pro-Mount base for Lopolight K-Lock lights, made for horizontal installations where the light needs a solid footing and a clean cable exit. The base is approximately Ø92.5 mm (3.6 in) and 45 mm (1.8 in) tall, with an IP68 rating for exposed mounting locations.\u003c\/p\u003e\u003cp\u003eThis 2CS+2CD version gives multiple cable routing paths, with two side cable entries and two bottom cable entries to match how your wiring comes through a mast, hardtop, or deck. The silver anodized aluminum finish has a 25 micron anodizing layer that holds up well in saltwater use when it is installed with proper bedding and isolation.\u003c\/p\u003e\u003cp\u003eIt is a good match for refits where the existing cable exit does not line up with a straight-down route, and for new builds where you want flexibility before the final cable path is locked in.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eK-Lock compatible Pro-Mount base for horizontal mounting\u003c\/li\u003e\n\u003cli\u003e2CS+2CD cable routing: two side cable entries and two bottom cable entries\u003c\/li\u003e\n\u003cli\u003eIP68-rated assembly for wet, exposed mounting positions\u003c\/li\u003e\n\u003cli\u003eCompact footprint: Ø92.5 mm (3.6 in) with 45 mm (1.8 in) height\u003c\/li\u003e\n\u003cli\u003eSilver anodized aluminum with a 25 micron anodizing layer\u003c\/li\u003e\n\u003cli\u003eWeight: 0.56 kg (19.75 oz)\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eWhat’s included\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eAluminum mounting base\u003c\/li\u003e\n\u003cli\u003eInstruction manual\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis base is intended for Lopolight lights that use the K-Lock interface. Before ordering, confirm your light family uses K-Lock and that a horizontal Pro-Mount base matches the way the light is oriented on your vessel.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003ePlan the cable run first, then dry-fit the base to confirm the exit direction clears your structure and does not force a tight bend at the entry point. Side exits are useful on masts and light bars; bottom exits suit through-deck routing when you have clearance underneath.\u003c\/p\u003e\u003cp\u003eBed the base and any penetrations with a marine sealant that matches your surface, and use appropriate backing so the mount stays stable under vibration. When fastening aluminum to stainless or other dissimilar metals, add isolation where practical to reduce galvanic corrosion over time.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eRinse with fresh water after salt exposure and check the mounting screws and cable entry points during routine inspections. If the base is mounted in a high-spray area, periodic checks help catch loosened fasteners or sealant wear before water finds a path into the cable run.\u003c\/p\u003e","brand":"Lopolight","offers":[{"title":"Default Title","offer_id":52268961071285,"sku":"QBP325368","price":231.97,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1298135_qbp325368.jpg?v=1771541071"},{"product_id":"qbp515874","title":"Lopolight 300 Series Double Masthead Light, 5 NM, Vertical Mount","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Lopolight 300-039 is a double stacked 225° white masthead navigation light with a 5 nautical mile rating for vessels from 20 m to 50 m, built for vertical mounting.\u003c\/p\u003e\u003cp\u003eIt contains two individual lights that can be powered separately, so one circuit can act as the primary masthead light and the second can be kept as a standby. The unit runs on 22 to 32 VDC and draws about 7 W (0.3 A at 24 VDC), with an IP68 seal for exposed positions on the mast.\u003c\/p\u003e\u003cp\u003eThis fixture is a good match for larger motor yachts and sailboats where redundancy matters and space for multiple masthead housings is limited.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eTwo independent white 225° masthead lights in one body, each switchable separately\u003c\/li\u003e\n\u003cli\u003eVisibility greater than 5 NM, sized for 20 m to 50 m vessels\u003c\/li\u003e\n\u003cli\u003eVertical mount format for mast or superstructure faces where the light needs to stay plumb\u003c\/li\u003e\n\u003cli\u003e22 to 32 VDC input, about 7 W total draw (0.3 A at 24 VDC)\u003c\/li\u003e\n\u003cli\u003eIP68 construction with electronics potted for resistance to water ingress and vibration\u003c\/li\u003e\n\u003cli\u003ePrecision machined 6082 aluminum housing with hard-coat anodized finish and PMMA lens\u003c\/li\u003e\n\u003cli\u003eApproved to COLREG72 and EN14744, with additional approvals including IEC 60945, USCG, and UL 1104\u003c\/li\u003e\n\u003cli\u003eOperating temperature range of -25°C to +55°C\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eMount the light on a flat, rigid surface so the lens stays vertical and the 225° sector faces forward as intended. Keep the insulating rings and isolation pieces in place when fastening to metal structures, and seal fastener penetrations to keep water out of the mounting surface and wiring path.\u003c\/p\u003e\u003cp\u003eBecause the two lights are separate, plan for two switched feeds at the helm or electrical panel and label them clearly so crews can identify primary and secondary at a glance.\u003c\/p\u003e\u003ch6\u003eElectrical and system integration\u003c\/h6\u003e\u003cp\u003eThe light is intended for 24 VDC nominal systems and operates across 22 to 32 VDC. It is pre-wired with two screened cables using 0.5 mm2 conductors; red is positive and black is negative for each circuit. Support the wiring near the fixture so motion and vibration are not carried into the cable entry point.\u003c\/p\u003e\u003ch6\u003eCompliance and visibility\u003c\/h6\u003e\u003cp\u003eThis is a masthead light with a 225° arc and a 5 NM intensity rating, intended for installations where meeting sectoring and range requirements matters. Verify the mounting height and fore and aft placement on your vessel, especially when a second masthead light is required by length and configuration.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eRinse salt off the lens and housing during routine washdowns, and recheck fasteners and cable support after the first few trips in rough water. Avoid aggressive solvents on the PMMA lens and inspect for chafe where the leads enter the structure.\u003c\/p\u003e\u003ch6\u003eWhat’s included\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eNavigation light with pre-cabled leads\u003c\/li\u003e\n\u003cli\u003eInstallation instructions\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Lopolight","offers":[{"title":"Default Title","offer_id":52268961562805,"sku":"QBP515874","price":3265.27,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1298137_qbp515874.jpg?v=1771541072"},{"product_id":"qbp676140","title":"Lopolight Spreader Light, White\/Red, Surface Mount, 12\/24VDC, IP68","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Lopolight 400-222 is a surface-mount spreader light with white and red output for lighting up deck areas without blasting your eyes at night.\u003c\/p\u003e\u003cp\u003eIt runs on 12VDC or 24VDC and draws 250 mA at 12VDC or 125 mA at 24VDC. The low-profile housing measures Ø65 mm x 12.5 mm (2.56 in x 0.5 in) and carries an IP68 rating for wet mounting locations on board.\u003c\/p\u003e\u003cp\u003eUse white when you are rigging, docking, or working lines on deck, then switch to red when you want light that is easier on night vision during night passages or at anchor.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eWhite and red light output for work lighting or low-glare night lighting\u003c\/li\u003e\n\u003cli\u003eIP68-rated sealing for spray, rain, and washdowns\u003c\/li\u003e\n\u003cli\u003eSupports 12VDC and 24VDC systems; draws 250 mA at 12VDC or 125 mA at 24VDC\u003c\/li\u003e\n\u003cli\u003eCompact size: Ø65 mm x 12.5 mm (2.56 in x 0.5 in)\u003c\/li\u003e\n\u003cli\u003eSurface-mount installation with two 4 mm mounting holes\u003c\/li\u003e\n\u003cli\u003eBuilt to meet IEC 60945 requirements for marine electronics environments\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eMount it on a flat surface under mast spreaders, a hardtop, or a radar arch where the light can wash the deck without shining straight into the helm. Before drilling, confirm you have clearance behind the mounting surface for wiring and that the area will not trap water.\u003c\/p\u003e\u003cp\u003eUse marine-grade fasteners suited to your mounting surface and seal any penetrations with a marine sealant. Leave a drip loop in the wiring run and support the cable so it does not flex at the entry point when the boat is pounding.\u003c\/p\u003e\u003ch6\u003eElectrical and system integration\u003c\/h6\u003e\u003cp\u003eConnect to your boat’s DC lighting circuit and protect the feed with an appropriately sized fuse or breaker for the circuit. Plan your switching so you can select white or red output from the helm or a nearby panel, and route wiring away from heat sources and moving rigging.\u003c\/p\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis light is a straightforward fit for 12V and 24V boats where you want a low-profile fixture. The 65 mm diameter body works well on most masts, hardtops, and arches, but check surface curvature and any internal obstructions before drilling the mounting holes.\u003c\/p\u003e\u003ch6\u003eUse cases on board\u003c\/h6\u003e\u003cp\u003eCommon installs include sailboat spreader lighting to light the foredeck, cockpit lighting for docking, and aft deck lighting for nighttime fishing prep. It suits crews who want a white work light at the dock and a red option underway to keep eyes adjusted to the dark.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eRinse with fresh water after saltwater use and inspect the sealant line and wiring support points during routine maintenance. In high-spray areas, check the mounting fasteners occasionally to make sure the fixture stays snug.\u003c\/p\u003e","brand":"Lopolight","offers":[{"title":"Default Title","offer_id":52269363757237,"sku":"QBP676140","price":290.97,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1299886_qbp676140.jpg?v=1771543600"},{"product_id":"qbp242091","title":"Lopolight 225 Degree Double Masthead Light, For Vessels Over 50m, White Light, 6NM, IP68, 22-32VDC, 13W, Horizontal Mount","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Lopolight 300-138 is a double masthead navigation light that shows a 225 degree white sector with a 6 nautical mile rating for vessels over 50 m (164 ft). It uses two separate light modules (primary and secondary) so either circuit can be run independently for redundancy.\u003c\/p\u003e\u003cp\u003eIt runs on 22 to 32 V DC (24 V systems) and draws 13 W, with an IP68 sealing level for exposed mast or superstructure mounting. The housing is aluminum with a silver anodized finish and a PMMA lens, and the electronics are potted to handle vibration and washdowns.\u003c\/p\u003e\u003cp\u003eOverall size is about 92.5 mm (3.64 in) diameter and 128 mm (5.03 in) height, with a listed weight of 1 kg. It mounts horizontally on the included base, with cable entry available from the side or bottom via M20x1.5 gland ports.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e225 degree white masthead sector with a 6 nautical mile visibility rating\u003c\/li\u003e\n\u003cli\u003eTwo independent light circuits (primary and secondary) for built-in redundancy\u003c\/li\u003e\n\u003cli\u003e22 to 32 V DC operating range for 24 V onboard systems\u003c\/li\u003e\n\u003cli\u003e13 W power consumption and intensity rated above 94 cd\u003c\/li\u003e\n\u003cli\u003eIP68 sealing with internal potting for water exposure and vibration\u003c\/li\u003e\n\u003cli\u003eOperating temperature range from -25°C to +55°C\u003c\/li\u003e\n\u003cli\u003eAluminum housing with a silver anodized finish and a PMMA lens\u003c\/li\u003e\n\u003cli\u003eSide or bottom cable routing using M20x1.5 cable-gland openings and a 5-pin connector\u003c\/li\u003e\n\u003cli\u003eComplies with COLREG72, EN14744, IEC 60945, and USCG UL1104 requirements, with LR certification\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eWhat’s included\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eDouble navigation light on 400-034 aluminum base\u003c\/li\u003e\n\u003cli\u003eHDPE base plate\u003c\/li\u003e\n\u003cli\u003e3 M6x14 screws\u003c\/li\u003e\n\u003cli\u003e2 M20x1.5 cable glands (for 7 to 13 mm cable diameter)\u003c\/li\u003e\n\u003cli\u003e2 M20x1.5 blinding caps\u003c\/li\u003e\n\u003cli\u003e5-pin connector plug\u003c\/li\u003e\n\u003cli\u003eInstallation instructions\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis light is intended for installations where a 6 nautical mile masthead light is required on vessels over 50 m (164 ft). It is suited to 24 V DC electrical systems and will not be a match for 12 V-only boats.\u003c\/p\u003e\u003cp\u003ePlan the mounting location so the 225 degree sector has a clear view forward and to the sides, without being blocked by antennas, domes, or crane structures. Confirm you have room for the 92.5 mm diameter body and the included base footprint, and that your cable routing can reach the gland position you want to use.\u003c\/p\u003e\u003ch6\u003eInstallation and wiring\u003c\/h6\u003e\u003cp\u003eThe unit mounts horizontally on the supplied base and accepts cable entry from either the side or bottom using the included M20x1.5 glands and caps. After positioning, keep the lens and sealing surfaces clean before final tightening so the IP68 sealing is not compromised.\u003c\/p\u003e\u003cp\u003ePrimary and secondary circuits are separated at the 5-pin connector. Pin 1 is primary positive and pin 2 is primary negative, pin 4 is secondary positive and pin 5 is secondary negative, and pin 3 is not used. This makes it straightforward to run independent feeds from a nav-light panel or a monitoring system while keeping the two light modules electrically separate.\u003c\/p\u003e\u003ch6\u003eUse on board\u003c\/h6\u003e\u003cp\u003eThis is a practical choice for commercial vessels, large motor yachts, and workboats that need a 6 nautical mile masthead light and want the added security of a second, independent light module in the same housing. It also fits well on boats doing long night transits where redundancy matters and access to the masthead is not convenient underway.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eRinse salt off the housing and lens during routine washdowns and check that the cable glands remain snug. If the lens becomes hazy or scratched, clean with a plastic-safe cleaner to avoid damaging the PMMA surface.\u003c\/p\u003e","brand":"Lopolight","offers":[{"title":"Default Title","offer_id":52269363953845,"sku":"QBP242091","price":3710.83,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1299887_qbp242091.jpg?v=1771543602"},{"product_id":"qbp438893","title":"Lopolight 360 Degree White LED Navigation Light, For Vessels Over 50m, 3NM, Ice-Class, Built-In De-Icing, 20-32VDC, IP68, Horizontal Mount","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Lopolight 300-112G2-PRO-I is a 3 NM, 360-degree white navigation light with an automatic de-icing function for operation in freezing conditions. It runs on 20-32VDC and is intended for vessels over 50 m where long-range visibility and continuous operation matter.\u003c\/p\u003e\u003cp\u003eThe de-icing function is controlled by an internal sensor, increasing power draw when needed while keeping the light output consistent for night running. The housing is IP68-rated for wet decks and washdowns, and the compact footprint (Ø92.5 mm x 89.5 mm) helps when mounting space is limited on rails, platforms, and superstructure faces.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e360-degree white light with 3 NM visibility and light intensity greater than 15 cd\u003c\/li\u003e\n\u003cli\u003eAutomatic de-icing function controlled by an in-built sensor for sub-zero operation\u003c\/li\u003e\n\u003cli\u003e20-32VDC input for common commercial DC systems\u003c\/li\u003e\n\u003cli\u003ePower draw: 4W in normal mode, 21W in de-icing mode (light on)\u003c\/li\u003e\n\u003cli\u003eIP68-rated for exposure to spray, rain, and washdowns\u003c\/li\u003e\n\u003cli\u003eHorizontal mounting with plug-connector connection for service access\u003c\/li\u003e\n\u003cli\u003eIncludes three cable glands for 4.5-10 mm, 7-13 mm, and 9-17 mm cable diameters\u003c\/li\u003e\n\u003cli\u003eHousing and fasteners selected for harsh marine environments: black hard coat anodized aluminum, PMMA lens, and A4 stainless steel screws\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eWhat’s included\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eNavigation light with plug connector\u003c\/li\u003e\n\u003cli\u003eThree cable glands for 4.5-10 mm, 7-13 mm, and 9-17 mm cable diameters\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eThis light is built for horizontal mounting. Confirm you have clear all-round visibility for a 360-degree light and that nearby structures, antennas, or cranes will not shadow the beam.\u003c\/p\u003e\u003cp\u003eUse the supplied cable glands to match your cable diameter and maintain a watertight seal at the entry point. On exposed mounting locations, careful sealing around fasteners and the mounting surface helps prevent water ingress into the structure beneath the light.\u003c\/p\u003e\u003ch6\u003eElectrical and system integration\u003c\/h6\u003e\u003cp\u003eWire the unit to a protected 20-32VDC circuit and size the protection to suit the vessel’s electrical standards, accounting for the higher draw during de-icing operation. The built-in sensor manages when de-icing is active, so the load profile can change in cold weather.\u003c\/p\u003e\u003ch6\u003eCompliance and operational fit\u003c\/h6\u003e\u003cp\u003eApproved to COLREG72, EN14744, IEC 60945, IACS E10, USCG, ABS, M.E.D., DNV, and LR, with conformance to USCG Commandant Instruction M16672.2. This is a good match for commercial operators and high-latitude routes where ice, spray, and vibration are part of normal service.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eRinse salt deposits as part of routine washdowns and check the lens for buildup that can reduce visibility. During periodic inspections, confirm the cable gland seal remains tight and that the mounting hardware stays secure after vibration and seasonal temperature swings.\u003c\/p\u003e","brand":"Lopolight","offers":[{"title":"Default Title","offer_id":52269366706357,"sku":"QBP438893","price":1491.45,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1299979_qbp438893.png?v=1771543611"},{"product_id":"qbp185995","title":"Lopolight Ice-Class 3NM 360° Red Navigation Light, IP68, 20-32VDC, De-Icing, Black Hard Coat Anodized","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Lopolight 300-114G2-PRO-I is a 3 NM 360° red navigation light with a built-in de-icing function for vessels over 50 m operating in freezing spray and icing conditions. It runs on 20-32 VDC and draws about 2.9 W.\u003c\/p\u003e\u003cp\u003eThe sealed IP68 assembly mounts horizontally on the 400-037 aluminum base with the cable exiting to the side. A plug connector lets you remove the light for service without pulling the full wiring run.\u003c\/p\u003e\u003cp\u003eThe compact body measures Ø92.5 mm x 89.5 mm and weighs 1.14 kg, which helps when you are fitting it on crowded masts or signal platforms where space and access are limited.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e360° red light with 3 NM visibility and intensity greater than 15 cd\u003c\/li\u003e\n\u003cli\u003eBuilt-in de-icing function for operation down to -60°C, with a rated upper limit of 55°C\u003c\/li\u003e\n\u003cli\u003e20-32 VDC input for 24 VDC systems; current consumption listed as 120 mA at 24 VDC\u003c\/li\u003e\n\u003cli\u003eIP68 rating for exposed locations that see spray and washdowns\u003c\/li\u003e\n\u003cli\u003eHorizontal mount on 400-037 aluminum base with side cable direction\u003c\/li\u003e\n\u003cli\u003eIncludes cable glands for 4.5-10 mm, 7-13 mm, and 9-17 mm cable diameters\u003c\/li\u003e\n\u003cli\u003eHousing made from black hard coat anodized aluminum (50 µm) with a PMMA lens and A4 stainless steel screws\u003c\/li\u003e\n\u003cli\u003eApprovals include COLREG72, EN14744, IEC 60945, IACS E10, and USCG, with additional listings that include ABS, M.E.D., DNV, and LR\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eMount the base on a rigid, flat surface with a clear 360° line of sight, and keep the light high enough that antennas, radar arrays, and rigging do not block the arc. The cable exits to the side, which can simplify routing inside a mast or along a rail where a bottom exit would force a tight bend.\u003c\/p\u003e\u003cp\u003eSeal the cable entry with the included gland that matches your cable diameter. Minimum feed wire gauge is 1.5 mm² (AWG 18). Power it from a protected DC circuit within the 20-32 VDC range, and support the cable close to the light so vibration does not work the entry loose over time.\u003c\/p\u003e\u003ch6\u003eUse cases on board\u003c\/h6\u003e\u003cp\u003eThis light suits commercial ships and larger yachts over 50 m that need a certified 3 NM all-round red light and want it to stay visible when ice starts building. It is commonly installed on masts, signal light platforms, or other exposed structures where icing and heavy weather are part of normal operations.\u003c\/p\u003e\u003ch6\u003eWhat’s included\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eNavigation light assembly with plug connector and built-in de-icing function\u003c\/li\u003e\n\u003cli\u003e400-037 aluminum mounting base (IP68)\u003c\/li\u003e\n\u003cli\u003eHDPE base plate\u003c\/li\u003e\n\u003cli\u003eCable glands in three sizes: 4.5-10 mm, 7-13 mm, and 9-17 mm cable diameter ranges\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Lopolight","offers":[{"title":"Default Title","offer_id":52269368049845,"sku":"QBP185995","price":1491.45,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1299981_qbp185995.png?v=1771543613"},{"product_id":"qbp381198","title":"Lopolight Adaptor Plate, For Single 180 G2 Navigation Light","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Lopolight 400-405 is an adaptor plate for mounting a Lopolight Single 180 G2 navigation light to the boat. It is a mechanical mounting part, so it draws 0 mA at both 12 VDC and 24 VDC.\u003c\/p\u003e\u003cp\u003eUse it when you need the correct mounting footprint between the light and the mounting surface, whether that is a flat panel, a mast bracket, or a custom pod. It helps the light sit square and stay tight when the boat is taking vibration and regular washdowns.\u003c\/p\u003e\u003cp\u003eThis is a good match for owners and builders installing a Single 180 G2 who want a clean mount without adding any electrical load or extra wiring to the circuit.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eMade for Lopolight Single 180 G2 navigation light installations\u003c\/li\u003e\n\u003cli\u003e0 mA current draw at 12 VDC and 24 VDC (no added electrical load)\u003c\/li\u003e\n\u003cli\u003eProvides the correct mounting interface between the light and the mounting surface\u003c\/li\u003e\n\u003cli\u003ePurely mechanical accessory, no wiring or network integration required\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eFits the Lopolight Single 180 G2 navigation light. Confirm your light is the Single 180 G2 version before ordering, since other Lopolight models use different footprints and hardware.\u003c\/p\u003e\u003cp\u003ePlan for enough clearance around the light body and cable exit once the adaptor plate is in place, especially on tight mast mounts, arches, and rail brackets.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eDry-fit the plate and light first, then mark and drill the mounting holes to match your structure. On cored decks or hardtops, seal the core properly around fasteners so water cannot migrate into the laminate.\u003c\/p\u003e\u003cp\u003eBed the mating surface and fasteners with a marine sealant suited for your mounting material. If you are joining dissimilar metals, use an isolating barrier and anti-seize where appropriate to slow down galvanic corrosion in saltwater.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eAs part of routine navigation light checks, confirm the mount has not worked loose and that the bedding has not cracked. Re-bed the joint if you ever see movement, staining, or water intrusion around the mounting holes.\u003c\/p\u003e","brand":"Lopolight","offers":[{"title":"Default Title","offer_id":52269368082613,"sku":"QBP381198","price":156.4,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1299983_qbp381198.jpg?v=1771543614"},{"product_id":"qbp770461","title":"Lopolight 200 Series Pro 2NM 360° Anchor Light, Black Anodized, 10-32V, IP68","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Lopolight 200-012G2-PRO is a 360 degree white LED anchor light with 2 NM visibility for vessels up to 50 m (164 ft). It runs on 10-32 VDC, which covers both 12V and 24V systems, and lists power draw as 2W \/ 6W.\u003c\/p\u003e\u003cp\u003eIt mounts horizontally on a POM base and carries an IP68 rating, so it suits exposed locations where spray and washdowns are normal. The housing is black hard coat anodized aluminum with a PMMA lens, and the body measures about 92.5 mm in diameter by 75 mm tall with a listed weight of 1 kg.\u003c\/p\u003e\u003cp\u003eAs an all-round white light, it is typically mounted high and clear so it can be seen from every direction when the boat is at anchor or lying to a mooring.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eAll-round 360 degree white light with 2 NM visibility, rated for vessels up to 50 m (164 ft).\u003c\/li\u003e\n\u003cli\u003e10-32 VDC input for 12V and 24V DC systems; listed power draw 2W \/ 6W.\u003c\/li\u003e\n\u003cli\u003eHorizontal mounting on an IP68-rated POM base for wet, exposed installations.\u003c\/li\u003e\n\u003cli\u003eSide-exit cable direction with a plug connector to keep the connection neat at the base.\u003c\/li\u003e\n\u003cli\u003eIncludes an HDPE base plate plus two cable glands for 4.5-10 mm and 7-13 mm cable diameters.\u003c\/li\u003e\n\u003cli\u003eBlack hard coat anodized aluminum housing (50 µ) with PMMA lens and A4 stainless steel fasteners.\u003c\/li\u003e\n\u003cli\u003eSpecified operating temperature range of -25C to 55C.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eMount the light where the lens has a clean 360 degree view with minimal shadowing from antennas, domes, flags, or rigging. For powerboats, this often lands on a hardtop, radar arch, or mast platform. For sailboats, a stern pole or a dedicated bracket can work as long as the light is high enough to avoid being blocked by the sail cover or backstay.\u003c\/p\u003e\u003cp\u003eBecause the cable exits to the side, leave room for the bend radius and secure the run so it cannot chafe at the entry point. Use the cable gland size that matches your cable jacket diameter so the seal grips evenly and stays watertight over time.\u003c\/p\u003e\u003ch6\u003eElectrical and system integration\u003c\/h6\u003e\u003cp\u003eConnect it to a switched 10-32 VDC circuit. Minimum feed wire gauge is listed as 0.5 mm2 (22 AWG); on longer runs, stepping up wire size helps reduce voltage drop. The plug connector at the light makes it easier to disconnect the fixture for service without pulling the full cable run.\u003c\/p\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis model is specified for boats in the under 12 m, 12-20 m, and 20-50 m ranges with a 2 NM visibility requirement. If you are replacing an existing all-round or anchor light, compare the footprint and the 92.5 mm diameter body size to confirm clearance and coverage over old fastener holes.\u003c\/p\u003e\u003ch6\u003eMaterials and corrosion resistance\u003c\/h6\u003e\u003cp\u003eThe housing uses a black hard coat anodized aluminum finish and A4 stainless steel hardware, with epoxy and polyurethane sealing listed for the assembly. That combination suits installations where salt, UV, vibration, and frequent washdowns are part of normal life on board.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eRinse salt and grime off the lens during routine washdowns and avoid abrasive pads that can haze PMMA. Periodically check mounting screws and the cable gland for tightness, especially after seasonal temperature changes or heavy weather runs.\u003c\/p\u003e\u003ch6\u003eWhat’s included\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eNavigation light\u003c\/li\u003e\n\u003cli\u003eInstallation guide\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Lopolight","offers":[{"title":"Default Title","offer_id":52269462126773,"sku":"QBP770461","price":730.5,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1299965_qbp770461.png?v=1771544079"},{"product_id":"qbp361833","title":"Lopolight PRO 360 Degree Navigation Light, Red Light, 2NM, 10-32VDC, IP68, Horizontal Mount, Black Anodized Housing, Built-In De-Icing","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Lopolight 200-014G2-PRO is a 360-degree red navigation light with a 2 NM visibility rating in a black-finished aluminum housing. It runs on 10-32 VDC for 12V and 24V systems, with typical power draw around 2.1 W.\u003c\/p\u003e\u003cp\u003eThis is an all-round red light intended for installations where the light must be seen through 360 degrees. The body and base are rated IP68, and the light uses a plug connector for the electrical connection.\u003c\/p\u003e\u003cp\u003eAt Ø92.5 mm x 75 mm (Ø3.6 in x 2.9 in) and 1 kg (35.27 oz), it suits boats that need a certified signal light in a compact footprint, including workboats and larger vessels where compliance and visibility matter.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eAll-round 360-degree red light with 2 NM visibility and intensity greater than 5.4 cd.\u003c\/li\u003e\n\u003cli\u003e10-32 VDC input for 12V and 24V systems; current draw is about 150 mA at 12 VDC or 85 mA at 24 VDC (2.1 W typical).\u003c\/li\u003e\n\u003cli\u003eIP68-rated sealing for heavy spray, washdowns, and wet mounting locations.\u003c\/li\u003e\n\u003cli\u003eHousing is hard coat anodized aluminum with a black finish (50µ), paired with a PMMA lens and A4 stainless fasteners.\u003c\/li\u003e\n\u003cli\u003eHorizontal mounting on a POM base with a side cable exit to keep wiring routed cleanly along the mounting surface.\u003c\/li\u003e\n\u003cli\u003eIncludes an HDPE base plate and cable glands sized for 4.5-10 mm and 7-13 mm cable diameters.\u003c\/li\u003e\n\u003cli\u003eBuilt-in de-icing function; when de-icing is active, draw increases to about 15 W at 24 VDC.\u003c\/li\u003e\n\u003cli\u003eApproved to COLREG72, EN14744, IEC 60945, IACS E10, USCG, ABS, M.E.D., DNV, and LR.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis light is specified for vessel categories under 12 m, 12-20 m, and 20-50 m. Confirm the required type and placement of an all-round red light for your vessel and operating area before mounting.\u003c\/p\u003e\u003cp\u003ePlan for the Ø92.5 mm body diameter and the side cable exit so the connector and wiring can be supported and protected from chafe. The 1 kg weight is worth considering if mounting on a thin hardtop or a cantilevered bracket.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eMount the light horizontally on a flat surface where it has an unobstructed view through 360 degrees. Use proper bedding and sealing practices around fasteners and the cable pass-through to preserve the IP68 rating.\u003c\/p\u003e\u003cp\u003eSelect the cable gland that matches your cable outside diameter, then secure the gland compression so the jacket is sealed without crushing the conductors. Support the wire run with clamps where possible to prevent vibration from working the connection loose over time.\u003c\/p\u003e\u003ch6\u003eElectrical and system integration\u003c\/h6\u003e\u003cp\u003eConnect to a 10-32 VDC lighting circuit with appropriate circuit protection for your wiring and switching. Normal load is low, but de-icing mode pulls more power, so the circuit should be sized with that higher draw in mind if de-icing will be used.\u003c\/p\u003e\u003ch6\u003eUse cases on board\u003c\/h6\u003e\u003cp\u003eThis style of all-round red light is commonly used on commercial vessels and larger yachts where a dedicated red signal light is required. It also fits boats that want a compact, certified 360-degree red light on a wheelhouse roof, mast platform, or aft deck structure with full-around visibility.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eRinse salt and grime off the lens and housing after rough weather or routine washdowns. During seasonal checks, inspect the base seal and cable gland compression so water cannot track into the wiring path.\u003c\/p\u003e","brand":"Lopolight","offers":[{"title":"Default Title","offer_id":52269462454453,"sku":"QBP361833","price":730.5,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1299969_qbp361833.png?v=1771544080"},{"product_id":"qbp699421","title":"Lopolight 360-Degree Red LED Navigation Light, De-Icing Function, 2nm, 10-32VDC, IP68, Horizontal Mount, Black Hard Coat Anodized","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Lopolight 200-014G2-PRO-I is a 360-degree red all-round navigation light with a built-in de-icing function for boats and commercial vessels up to 50 m. It runs on 10-32 VDC for 12V or 24V systems and carries a 2 nautical mile (2 NM) rating with intensity greater than 5.4 cd.\u003c\/p\u003e\u003cp\u003eFor cold-weather operation, the de-icing mode helps keep the lens clear when freezing spray or ice buildup would otherwise block the light. Normal power draw is 2.1 W, and de-icing draws about 15 W at 24 VDC, so it is worth planning the circuit for that higher load.\u003c\/p\u003e\u003cp\u003eThe housing is hard coat anodized aluminum in a black finish (50 micron anodizing) with a PMMA lens and A4 stainless steel fasteners. The assembly is rated IP68 and is approved to COLREG72, EN14744, IEC 60945, IACS E10, USCG, ABS, M.E.D., DNV, and LR.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e360-degree red all-round light rated for 2 NM visibility and intensity greater than 5.4 cd.\u003c\/li\u003e\n\u003cli\u003eBuilt-in de-icing function to help keep the lens clear in freezing spray and icing conditions.\u003c\/li\u003e\n\u003cli\u003eWide input range of 10-32 VDC for use on both 12V and 24V systems.\u003c\/li\u003e\n\u003cli\u003ePower draw is 2.1 W in normal operation; de-icing draws about 15 W at 24 VDC.\u003c\/li\u003e\n\u003cli\u003eIP68-rated construction for heavy weather and washdowns.\u003c\/li\u003e\n\u003cli\u003eHorizontal mounting with side cable direction and a plug connector for service-friendly wiring.\u003c\/li\u003e\n\u003cli\u003eCompact footprint at Ø92.5 mm x 75 mm (Ø3.6 in x 2.9 in) for mounting on cabin tops, hardtops, and deck structures.\u003c\/li\u003e\n\u003cli\u003eMaterials include black hard coat anodized aluminum (50 micron anodizing), a PMMA lens, and A4 stainless steel screws.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eThis light is a horizontal-mount unit, so it should be installed on a flat surface where it has an unobstructed 360-degree view. Pay attention to antennas, rails, and other fittings that can shadow an all-round light, especially on workboats and pilothouse roofs where gear tends to accumulate.\u003c\/p\u003e\u003cp\u003ePlan the cable run before drilling so the side-exit wiring lands where it can be protected from foot traffic, line handling, and chafe. In saltwater service, a small drip loop and a tidy clamp-down near the entry point help keep water from tracking along the cable into the boat.\u003c\/p\u003e\u003ch6\u003eElectrical and system integration\u003c\/h6\u003e\u003cp\u003eOperating voltage is 10-32 VDC, which fits typical 12V and 24V DC systems. Current consumption is 150 mA at 12 VDC and 85 mA at 24 VDC in normal operation, and the de-icing mode increases load, so confirm the breaker or fuse and switch capacity for the highest draw you expect to use.\u003c\/p\u003e\u003cp\u003eMinimum feed wire gauge is 1.5 mm2 (AWG 18). On longer runs, going heavier than the minimum can help reduce voltage drop and keep light output consistent.\u003c\/p\u003e\u003ch6\u003eMaterials and corrosion resistance\u003c\/h6\u003e\u003cp\u003eThe housing uses hard coat anodized aluminum in a black finish with a PMMA lens and A4 stainless fasteners. Regular freshwater rinsing after saltwater trips helps keep the lens clear and reduces salt buildup around fasteners and cable entry points.\u003c\/p\u003e\u003ch6\u003eUse on board\u003c\/h6\u003e\u003cp\u003eThis is a practical fit for operators who run in cold climates where icing is a real problem, including commercial boats, fast pilot-style vessels, and cruising boats that see shoulder-season weather. It also works well on boats that need a compact 2 NM all-round red light on a cabin top, mast structure, or other elevated mounting location.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eCheck the lens for film, salt, and ice residue, and rinse with fresh water after trips. Periodically inspect the mounting hardware and cable strain relief for loosening from vibration, and confirm the seal surfaces stay clean before reassembly if the unit is serviced.\u003c\/p\u003e","brand":"Lopolight","offers":[{"title":"Default Title","offer_id":52269462782133,"sku":"QBP699421","price":1125.07,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1299971_qbp699421.png?v=1771544082"},{"product_id":"qbp425641","title":"Lopolight 225 Deg Masthead Light, 2nm, White Light, Vertical Mount, Silver Housing, 10-32VDC, IP68","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Lopolight 201-010 is a 225° white LED masthead light for vertical mounting, rated for 2 NM visibility on vessels under 12 m.\u003c\/p\u003e\u003cp\u003eIt runs on 10-32 VDC, so it fits both 12V and 24V systems without a converter. Power draw is 2 W, with typical current around 137 mA at 12V and 80 mA at 24V, which keeps the load light on smaller electrical systems.\u003c\/p\u003e\u003cp\u003eThe housing is anodized aluminum finished in silver with a PMMA lens, and the unit is IP68-rated for wet marine locations when installed correctly. At roughly 74.6 x 28 x 73.2 mm (2.9 x 1.1 x 2.88 in) and about 0.42 kg (14.8 oz), it fits cleanly on masts, arches, and hardtops where space is tight.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e225° white masthead light with 2 NM visibility, intended for vessels under 12 m (39 ft).\u003c\/li\u003e\n\u003cli\u003e10-32 VDC input for 12V and 24V systems, with 2 W power draw (about 137 mA @ 12V and 80 mA @ 24V).\u003c\/li\u003e\n\u003cli\u003eIP68 rating for exposure to spray and washdowns when the cable entry and mounting surface are sealed properly.\u003c\/li\u003e\n\u003cli\u003eAnodized aluminum housing finished in silver with a PMMA lens, supplied with A4 stainless mounting screws.\u003c\/li\u003e\n\u003cli\u003ePre-cabled with approximately 0.75 m (2.5 ft) shielded marine-grade cable to simplify routing to a junction point or switch panel.\u003c\/li\u003e\n\u003cli\u003eCompact size and weight for cleaner installs: 74.6 x 28 x 73.2 mm (2.9 x 1.1 x 2.88 in), about 0.42 kg (14.8 oz).\u003c\/li\u003e\n\u003cli\u003eApproved to COLREG72 and EN14744, with additional listings including IEC 60945 and IACS E10 and approvals noted for USCG, ABS, M.E.D., DNV, and LR.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis light is used as the 225° masthead (steaming) light in a standard navigation-light arrangement, typically shown when a sailboat is under power or on power-driven vessels that require a masthead light. Since requirements vary by vessel length and configuration, confirm that a 2 NM masthead light is the correct requirement for your boat and where it needs to sit relative to other navigation lights.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eThe vertical mount format is meant to be fastened to a flat, stable surface on the vessel centerline with the lens oriented forward so the 225° arc covers ahead and out to each side. Pick a location where sails, antennas, rigging, or rails will not shadow the light, then route the pre-attached cable to a dry connection point using strain relief so vibration does not work the wiring loose over time.\u003c\/p\u003e\u003ch6\u003eElectrical and system integration\u003c\/h6\u003e\u003cp\u003eWire it into a switched navigation-light circuit that matches your onboard voltage. Even with the low current draw, use marine tinned wire and sealed connectors, and keep splices in a protected area when possible. A properly sized fuse or breaker on the nav light feed is still important for protecting the wiring run.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eRinse the housing and lens after saltwater use and avoid abrasive cleaners on the lens. Periodically check that the mounting fasteners stay tight and that the cable entry remains sealed, especially if the light is mounted where it takes frequent spray or deck washdowns.\u003c\/p\u003e\u003ch6\u003eWhat’s included\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e1 navigation light, pre-cabled with 0.75 m shielded marine-grade cable\u003c\/li\u003e\n\u003cli\u003e2 mounting screws (M6 x 8 mm)\u003c\/li\u003e\n\u003cli\u003eInstallation guide\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Lopolight","offers":[{"title":"Default Title","offer_id":52269463240885,"sku":"QBP425641","price":498.32,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1299975_qbp425641.png?v=1771544084"},{"product_id":"qbp638612","title":"Lopolight PRO Towing Light, 2NM, 135°, Yellow Light, 10-32VDC, IP68","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Lopolight 201-013-PRO is a 2 NM yellow towing navigation light with a 135-degree sector and a housing in hard coat anodized aluminum with a black finish. It runs on 10-32 VDC for 12V and 24V DC systems, and it carries an IP68 rating for mounting positions that see spray, rain, and regular washdowns.\u003c\/p\u003e\u003cp\u003eThe light mounts horizontally on a POM base with the cable exiting to the side, which helps when you are feeding wiring through a transom or a stern structure. Power connects via a plug connector, so it is worth confirming you have the correct mating connector or harness in your wiring run before final installation.\u003c\/p\u003e\u003cp\u003eOverall size is 92.5 mm diameter by 74.5 mm tall (3.6 in x 2.9 in), and weight is 1.04 kg (36.68 oz). It is specified for operation from -25 C to 55 C, and it is approved to COLREG72, EN14744, IEC 60945, IACS E10, USCG, ABS, M.E.D., DNV, and LR.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e2 NM visibility yellow towing light with a 135-degree sector\u003c\/li\u003e\n\u003cli\u003e10-32 VDC input for 12V and 24V DC systems\u003c\/li\u003e\n\u003cli\u003eLow electrical load: 1.7 W (124 mA at 12VDC, 71 mA at 24VDC)\u003c\/li\u003e\n\u003cli\u003eIP68 sealing for exposed stern locations and wet environments\u003c\/li\u003e\n\u003cli\u003eHorizontal mounting on a POM base with side cable direction\u003c\/li\u003e\n\u003cli\u003eHDPE base plate used under the mount\u003c\/li\u003e\n\u003cli\u003eCable gland sized for 7-13 mm cable diameter\u003c\/li\u003e\n\u003cli\u003eBlack hard coat anodized aluminum (50 micron) with a PMMA lens and A4 stainless steel screws\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eWhat's included\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eNavigation light\u003c\/li\u003e\n\u003cli\u003e2 mounting screws (M6 x 8 mm)\u003c\/li\u003e\n\u003cli\u003eInstallation guide\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis is a towing light for vessels specified up to 50 m (164 ft). Plan the mounting position so the 135-degree arc is not blocked by davits, rails, trim tabs, antennas, or any stern gear that can cast a shadow across the sector.\u003c\/p\u003e\u003cp\u003eWith a 92.5 mm diameter body and a 74.5 mm overall height, it fits many stern faces and light brackets where space is limited but you still want a full-size navigation light footprint.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eMount the light horizontally and square to the vessel centerline so the towing sector lines up correctly. Use the included M6 fasteners where the mounting surface and backing allow it, and seal penetrations appropriately for your transom or stern structure.\u003c\/p\u003e\u003cp\u003eThe side cable exit can make routing easier in tight stern compartments. Leave enough service loop to access the plug connection without having to remove the light from the mounting surface.\u003c\/p\u003e\u003ch6\u003eElectrical and system integration\u003c\/h6\u003e\u003cp\u003eSupply power within the 10-32 VDC range. Current draw is 124 mA at 12VDC or 71 mA at 24VDC, which helps keep the load modest on navigation light circuits.\u003c\/p\u003e\u003cp\u003eMinimum feed wire size is 0.5 mm2 (22 AWG). If you are extending the run, choose conductor size based on distance and voltage drop, and keep connections dry and strain-relieved in a location you can inspect later.\u003c\/p\u003e\u003ch6\u003eUse on board\u003c\/h6\u003e\u003cp\u003eThis light is a good match for towboats, tugs, and workboats that need a dedicated yellow towing light while keeping power draw low on 12V or 24V systems. It also works well for refits where you are replacing older incandescent towing lights and want a sealed fixture rated IP68.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eRinse the light after saltwater use, especially around the mounting base and cable entry points. Check the lens for buildup that can reduce visibility, and re-torque fasteners during routine inspections so vibration does not loosen the installation over time.\u003c\/p\u003e","brand":"Lopolight","offers":[{"title":"Default Title","offer_id":52269463470261,"sku":"QBP638612","price":730.5,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1299977_qbp638612.png?v=1771544086"},{"product_id":"qbp861423","title":"Lopolight MFD Control Hub, 10-32V DC, 16-Channel, 10A Total","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Lopolight 500-001 is a 10A control hub that lets you switch and monitor onboard lights and other DC circuits from a compatible multifunction display over Ethernet.\u003c\/p\u003e\u003cp\u003eIt runs on 10 to 32V DC for 12V and 24V systems and provides 16 output channels with current monitoring. Each channel supports up to 2A, with 10A total across the unit. The housing is about 150 x 150 x 40 mm, which makes it easy to mount behind the helm, inside a console, or in an electrical locker as long as it stays dry and reachable.\u003c\/p\u003e\u003cp\u003eAlongside control from the screen, the unit has emergency manual override and four input channels for wired switches, so you still have a direct way to bring on key circuits when you want local control.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e10 to 32V DC input for 12V and 24V electrical systems\u003c\/li\u003e\n\u003cli\u003e16 output channels with current monitoring to help spot a failed load or an open circuit\u003c\/li\u003e\n\u003cli\u003eUp to 2A per channel, with 10A total capacity across the hub\u003c\/li\u003e\n\u003cli\u003ePWM dimming available on supported channels for loads that need adjustable output\u003c\/li\u003e\n\u003cli\u003eFour hardware input channels for linking physical switches to group control\u003c\/li\u003e\n\u003cli\u003eRJ45 Ethernet connection using TCP\/IP for integration with compatible touch MFDs\u003c\/li\u003e\n\u003cli\u003eAlarm buzzer output for an external audible alarm located where you can hear it\u003c\/li\u003e\n\u003cli\u003eManual override on the unit for basic emergency operation\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThe hub connects through a standard RJ45 Ethernet port and communicates over TCP\/IP. Use CAT5 or higher Ethernet cabling, or the appropriate Raymarine and Garmin marine network cables when tying into those systems.\u003c\/p\u003e\u003cp\u003eIt integrates with compatible touch MFDs, including Raymarine Axiom and Garmin GPSMAP series units with current software. The control screen appears as an onboard app on the display.\u003c\/p\u003e\u003ch6\u003eInstallation and wiring notes\u003c\/h6\u003e\u003cp\u003eMount the hub in a dry, ventilated location and keep it accessible so the manual override can be used if needed. Leave distance from a magnetic compass if you notice interference, with about 1 m (3 ft) as a practical starting point.\u003c\/p\u003e\u003cp\u003eProtect the main DC feed with a 10A fuse and size the supply wiring for the total expected load. Each output channel is intended for loads up to 2A. For any circuit that needs more than 2A, use the hub to switch an external relay so the higher current stays out of the channel output.\u003c\/p\u003e\u003cp\u003eUsing strand-protection ferrules on the terminal connections helps keep wiring secure in a vibrating marine environment.\u003c\/p\u003e\u003ch6\u003eUse cases on board\u003c\/h6\u003e\u003cp\u003eThis setup works well when you want navigation lights, deck and docking lights, wipers, fans, or bilge-related alarms controlled from the same screen you already use underway. Current monitoring and the alarm output add a layer of awareness when a circuit draws less power than expected.\u003c\/p\u003e\u003ch6\u003eWhat’s included\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eControl hub hardware\u003c\/li\u003e\n\u003cli\u003eQuick guide\u003c\/li\u003e\n\u003cli\u003eWiring schematic diagram\u003c\/li\u003e\n\u003cli\u003eConnection layout sticker for labeling channel assignments\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Lopolight","offers":[{"title":"Default Title","offer_id":52269526057141,"sku":"QBP861423","price":1424.08,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1300183_qbp861423.png?v=1771544433"},{"product_id":"qbp247735","title":"Lopolight Combined Sidelight Navigation Light, Upside-Down, 1NM, Red\/Green Light, Silver Anodized Housing, IP68, 10-32VDC, Horizontal Mount, FB Base, 2.5m Cable","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Lopolight 101-003-FB-REVERSE is a 1 NM combined sidelight that shows red to port and green to starboard from one fixture, with an upside-down horizontal mount and an FB base. It runs on 10-32VDC and draws 1.4W (87 mA at 12VDC, 48 mA at 24VDC), which keeps the load small on both 12V and 24V systems.\u003c\/p\u003e\u003cp\u003eThis light is sealed to IP68 and comes pre-cabled with 2.5 m of shielded marine-grade cable, so you can route the lead to a dry junction point without splicing right at the base. It is built for marine exposure with a silver anodized aluminum housing (25µ), a PMMA lens, and A4 stainless steel screws, and it is rated for -25°C to 55°C operation.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e1 NM combined red\/green sidelight coverage from a single unit, with 2 x 112.5° sectors\u003c\/li\u003e\n\u003cli\u003e10-32VDC input with 1.4W draw (87 mA at 12VDC, 48 mA at 24VDC)\u003c\/li\u003e\n\u003cli\u003eIP68 sealing for wet installations and washdowns\u003c\/li\u003e\n\u003cli\u003ePre-cabled with 2.5 m shielded marine-grade cable\u003c\/li\u003e\n\u003cli\u003eSilver anodized aluminum housing (25µ) with PMMA lens and A4 stainless steel screws\u003c\/li\u003e\n\u003cli\u003eHorizontal mounting with an upside-down orientation; mounting options support install from the top or from the underside\u003c\/li\u003e\n\u003cli\u003eMinimum feed wire gauge: 0.5 mm2 (AWG 22)\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis is a 1 NM navigation light intended for leisure vessels up to 12 meters. As a combined sidelight, it is typically mounted on the vessel centerline where it can show the correct red and green sectors without being blocked by rails, pulpits, or deck gear.\u003c\/p\u003e\u003cp\u003eIt is a good match for small sailboats, center consoles, RIBs, and sportfishing boats where you want a clean bow install and prefer one combined light instead of separate port and starboard fixtures.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003ePlan the mounting position so the light has a clear view out to each side and the unit can be aligned correctly to the vessel centerline. The FB base supports mounting from the top using three through-holes, or from the underside using three M4 x 0.7 threaded mounting points.\u003c\/p\u003e\u003cp\u003eBed the base properly for the mounting surface and route the cable so it is protected from chafe and standing water. If you extend the lead, make the splice in a dry area or inside a sealed junction, and keep the connection serviceable for future troubleshooting.\u003c\/p\u003e\u003ch6\u003eElectrical and system integration\u003c\/h6\u003e\u003cp\u003eThe light is supplied as a DC fixture for 10-32V systems. Provide circuit protection appropriate for your boat and wiring run, and use marine-grade connectors and heat-shrink sealing where the wiring may see spray or condensation.\u003c\/p\u003e\u003cp\u003eThe supplied cable length helps keep the transition to your vessel wiring away from the mounting point, which is helpful on bowsprits, pulpits, and slim deck caps where access is tight.\u003c\/p\u003e\u003ch6\u003eCompliance and approvals\u003c\/h6\u003e\u003cp\u003eApproved to COLREG72, EN14744, IEC 60945, IACS E10, USCG, ABS, M.E.D., DNV, and LR.\u003c\/p\u003e\u003ch6\u003eWhat’s included\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eNavigation light, pre-cabled with 2.5 m shielded marine-grade cable\u003c\/li\u003e\n\u003cli\u003eInstallation guide\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Lopolight","offers":[{"title":"Default Title","offer_id":52269541490869,"sku":"QBP247735","price":594.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1300180_qbp247735.jpg?v=1771544512"},{"product_id":"qbp028669","title":"Lopolight 2nm 360 Red\/White Navigation Light, For Vessels Up to 50m, 10-32VDC, IP68, Silver Anodized Housing, Horizontal Mount","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Lopolight 200-014G2+012G2 is a 360 degree navigation light with separate all-round red and all-round white outputs, each rated for 2 nautical miles on 10-32 VDC systems.\u003c\/p\u003e\u003cp\u003eThe housing is silver anodized aluminum with a PMMA lens and A4 stainless screws, sealed to an IP68 rating for wet decks and washdowns. It measures 92.5 mm in diameter by 68 mm tall and draws 2.1 W (150 mA at 12 VDC, 85 mA at 24 VDC).\u003c\/p\u003e\u003cp\u003eOn board, this style of combined red and white all-round light helps keep the mast, hardtop, or radar arch cleaner when you need both signals from the same mounting point.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eTwo outputs in one housing: 360 degree red and 360 degree white\u003c\/li\u003e\n\u003cli\u003e2 nautical mile visibility\u003c\/li\u003e\n\u003cli\u003e10-32 VDC input for 12 V and 24 V DC systems\u003c\/li\u003e\n\u003cli\u003eIP68 sealed housing for exposure to spray, rain, and washdowns\u003c\/li\u003e\n\u003cli\u003eLow draw: 2.1 W, 150 mA at 12 VDC and 85 mA at 24 VDC\u003c\/li\u003e\n\u003cli\u003eHorizontal mounting with a compact body size of 92.5 mm diameter x 68 mm height\u003c\/li\u003e\n\u003cli\u003eApproved to COLREG72, EN14744, IEC 60945, IACS E10, and USCG (plus ABS, MED, DNV, and LR)\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eWhat’s included\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eNavigation light\u003c\/li\u003e\n\u003cli\u003e0.75 m shielded marine grade cable (pre-attached)\u003c\/li\u003e\n\u003cli\u003eInstallation guide\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eMount the light on a level surface so the lens sits true and the beam clears 360 degrees without being blocked by antennas, radar mounts, or a bimini edge. Keep it positioned to maintain the required visibility and separation for your vessel’s navigation light arrangement.\u003c\/p\u003e\u003cp\u003eBecause the unit is pre-cabled, plan the cable route before drilling. Keep bends gentle, protect the wire where it passes through metal, and seal deck penetrations so water cannot track along the cable into a core or overhead.\u003c\/p\u003e\u003ch6\u003eElectrical and system integration\u003c\/h6\u003e\u003cp\u003eIt operates from 10 to 32 VDC and can be wired into a 12 V or 24 V DC distribution panel. Use switching that matches how your boat controls the red and white circuits so the correct signal is shown when selected.\u003c\/p\u003e\u003cp\u003eMinimum feed wire gauge is 0.5 mm2 (AWG22). On longer runs, stepping up wire size helps keep voltage drop down, especially on a 12 V system.\u003c\/p\u003e\u003ch6\u003eCompatibility and compliance\u003c\/h6\u003e\u003cp\u003eThe approvals cover COLREG72 and USCG requirements and also include EN14744, IEC 60945, and IACS E10. It is listed across vessel size categories under 12 m, 12 to 20 m, and 20 to 50 m, with final fit determined by your local rules and your vessel’s navigation light plan.\u003c\/p\u003e\u003ch6\u003eUse on board\u003c\/h6\u003e\u003cp\u003eThis is a good match for boats that need an all-round white light and an all-round red signal light from the same mounting point, such as workboats, tenders, and yachts where space is tight on the mast or hardtop. It also suits refits where you want LED efficiency without adding a second fixture and extra cable runs.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eRinse salt off the lens and housing after trips and avoid abrasive cleaners that can haze PMMA. During seasonal checks, confirm the mounting screws stay tight, the cable jacket is intact, and the sealant around the cable pass-through is still sound.\u003c\/p\u003e","brand":"Lopolight","offers":[{"title":"Default Title","offer_id":52269730201781,"sku":"QBP028669","price":1425.82,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1299967_qbp028669.jpg?v=1771545438"},{"product_id":"qbp029030","title":"Lopolight Tri-Color\/Anchor Navigation Light, 2NM, 10-32VDC, IP68, 0.75m Cable","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Lopolight 201-007G2 is a 2 NM tri-color navigation light with a white all-round anchor light in a silver anodized housing, built for horizontal mounting at the masthead on sailboats up to 66 ft.\u003c\/p\u003e\u003cp\u003eIt runs on 10-32 VDC, so it fits 12V and 24V DC systems without a converter, and the housing is IP68 for wet masthead conditions. The compact body measures Ø92.5 mm x 68 mm (3.6 x 2.6 in) and weighs 1.0 kg, which helps when you are planning a masthead bracket or plate.\u003c\/p\u003e\u003cp\u003ePower draw is 2.9 W (213 mA at 12VDC and 123 mA at 24VDC), so it is easy to leave on overnight at anchor without putting a big dent in your house bank.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e2 NM visibility tri-color light (red, green, white) combined with a white all-round anchor light\u003c\/li\u003e\n\u003cli\u003e10-32 VDC input for 12V and 24V boats; 2.9 W draw (213 mA at 12VDC, 123 mA at 24VDC)\u003c\/li\u003e\n\u003cli\u003eIP68 sealing for spray, rain, and washdowns at the masthead\u003c\/li\u003e\n\u003cli\u003eSilver anodized aluminum body (25 micron) with PMMA lens and A4 stainless steel screws\u003c\/li\u003e\n\u003cli\u003eHorizontal mount format; Ø92.5 mm x 68 mm overall size; 1.0 kg unit weight\u003c\/li\u003e\n\u003cli\u003ePre-cabled with 0.75 m shielded marine-grade cable; minimum feed wire gauge 0.5 mm2 (AWG 22)\u003c\/li\u003e\n\u003cli\u003eApproved to COLREG72 and EN14744, IEC 60945, and IACS E10 (plus USCG, ABS, M.E.D., DNV, LR approvals)\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eWhat’s included\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eNavigation light assembly (tri-color with anchor light)\u003c\/li\u003e\n\u003cli\u003e0.75 m shielded marine-grade cable (pre-attached)\u003c\/li\u003e\n\u003cli\u003eInstallation guide\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003ePlan the mount so the lens has a clear view around the boat and is not shadowed by antennas, wind sensors, or a burgee. A small obstruction near the masthead can create blind sectors that are hard to notice until you are out at night.\u003c\/p\u003e\u003cp\u003eRoute the factory cable inside the mast where possible and add strain relief at the light and at the first connection point. The housing is sealed, but the wire terminations still need a dry, protected spot such as inside the mast, a junction box, or behind an instrument panel.\u003c\/p\u003e\u003cp\u003eUse at least the specified minimum conductor size (0.5 mm2 \/ AWG 22) and keep connections clean and well supported so vibration does not work-harden the wire over time.\u003c\/p\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThe wide 10-32 VDC input range matches typical onboard DC power, including charging voltages. Confirm your switching arrangement matches how you want to operate tri-color versus anchor mode so you are not back-feeding circuits or leaving both functions on at the same time.\u003c\/p\u003e\u003cp\u003eFor masthead planning, allow room for the Ø92.5 mm footprint and the cable exit, and account for the 1.0 kg weight when choosing a bracket or mounting plate.\u003c\/p\u003e\u003ch6\u003eMaterials and corrosion resistance\u003c\/h6\u003e\u003cp\u003eThe body is anodized aluminum with A4 stainless fasteners, which holds up well in salt spray when the installation is kept tight and free of crevice corrosion traps. A quick freshwater rinse after heavy weather or salty passages helps keep the lens clean and the mounting hardware easier to service later.\u003c\/p\u003e\u003cp\u003eThis light is rated for -25°C to 55°C, which covers typical seasonal sailing and most exposed masthead conditions.\u003c\/p\u003e\u003ch6\u003eUse on board\u003c\/h6\u003e\u003cp\u003eThis configuration suits cruising and performance sailboats that want one masthead fixture for under-sail navigation lighting and a separate anchor light function for nights on a mooring or hook. It is a good match for boats that spend time offshore or in busy harbors where being seen early matters.\u003c\/p\u003e","brand":"Lopolight","offers":[{"title":"Default Title","offer_id":52269731283125,"sku":"QBP029030","price":1056.96,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1299973_qbp029030.png?v=1771545441"},{"product_id":"qbp041830","title":"Lopolight PRO Series 360° Double Red Navigation Light, 3NM Visibility, 20-32VDC, IP68, Built-In De-Icing","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Lopolight 300-114G2ST-PRO-I is a 3 nm, 360° red double navigation and signal light with a built-in de-icing function for larger commercial vessels. It runs on 20-32 VDC (24 V systems), is sealed to IP68, and draws about 2.9 W.\u003c\/p\u003e\u003cp\u003eThe housing measures Ø92.5 mm x 112 mm and uses a hard coat anodized aluminum body with a PMMA lens. It is approved to COLREG72 and EN14744, and it is also listed for IEC 60945 and IACS E10.\u003c\/p\u003e\u003cp\u003eThis is a good match for operators who need an all-round red light that stays visible in spray and cold weather, including vessels that see winter service where icing can block a lens.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e3 nm visibility with a full 360° red sector in a double-light configuration\u003c\/li\u003e\n\u003cli\u003eBuilt-in de-icing and a stated operating range of -60°C to 55°C\u003c\/li\u003e\n\u003cli\u003e20-32 VDC input for 24 V systems; power draw listed as 2.9 W (about 120 mA at 24 VDC)\u003c\/li\u003e\n\u003cli\u003eIP68-rated assembly with plug-connector connection for service-friendly removal\u003c\/li\u003e\n\u003cli\u003eHorizontal mounting on a 400-037 POM base, with side cable exit and an HDPE base plate\u003c\/li\u003e\n\u003cli\u003eHard coat anodized aluminum (50 micron) housing with PMMA lens and A4 stainless steel screws\u003c\/li\u003e\n\u003cli\u003eCompact footprint (Ø92.5 mm x 112 mm) and 1.52 kg weight for mast or superstructure mounting\u003c\/li\u003e\n\u003cli\u003eMinimum feed wire gauge listed as 1.5 mm² (AWG 18)\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eWhat's included\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eNavigation light assembly\u003c\/li\u003e\n\u003cli\u003e400-037 POM mounting base\u003c\/li\u003e\n\u003cli\u003eHDPE base plate\u003c\/li\u003e\n\u003cli\u003eCable gland for 7-13 mm (9\/32\" to 1\/2\") cable diameter\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003ePlan the mounting location so the light has an unobstructed 360° view and the lens sits level. On larger vessels this is often on a mast platform or a dedicated bracket on the superstructure, clear of antennas, davits, rails, and other structures that can mask the arc.\u003c\/p\u003e\u003cp\u003eThe unit mounts horizontally to the 400-037 base, and the cable exits to the side. Route the cable so it is supported against vibration, with a drip loop before the deck penetration and enough slack to disconnect the plug connector during service.\u003c\/p\u003e\u003ch6\u003eElectrical and system integration\u003c\/h6\u003e\u003cp\u003eSupply is 20-32 VDC, which aligns with 24 VDC shipboard systems. With a listed draw of 2.9 W, circuit loading is modest, but de-icing is meant for cold-weather operation, so the circuit should be wired and protected to your vessel standards.\u003c\/p\u003e\u003cp\u003eUse at least 1.5 mm² (AWG 18) feed conductors as a minimum and keep terminations sealed from moisture. If you are tying into a navigation light panel or monitoring system, confirm it supports the light's voltage range and the plug-connector interface.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eRinse salt deposits during routine washdowns and inspect the lens and cable gland for loosening. In icing conditions, confirm the lens area stays clear and re-check fasteners on the base after the first few runs.\u003c\/p\u003e","brand":"Lopolight","offers":[{"title":"Default Title","offer_id":52269740916917,"sku":"QBP041830","price":1760.86,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1301167_qbp041830.png?v=1771545490"},{"product_id":"qbp076742","title":"Lopolight Double-Stacked 360° Navigation Light, 3NM, White Light, Silver Anodized, 10-32VDC, IP68","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Lopolight 300-112G2ST is a 3 nautical mile, 360° all-round white navigation light with a double-stacked light output, made for horizontal mounting on larger vessels. It runs on 10-32VDC for 12V and 24V systems, draws 4.2W (270mA at 12V, 176mA at 24V), and carries an IP68 rating for exposed masthead installations.\u003c\/p\u003e\u003cp\u003eThe body measures Ø92.5mm x 96.5mm and weighs 1.31kg. Construction uses silver anodized aluminum (25µ) with a PMMA lens, A4 stainless steel screws, and fully sealed internal components with epoxy and polyurethane. Approval coverage includes COLREG72 along with EN14744, IEC 60945, IACS E10, USCG, ABS, M.E.D., DNV, and LR.\u003c\/p\u003e\u003cp\u003eThis style of 360° light is used where you need an all-round white arc with clear visibility and minimal shadowing from antennas or rigging. It is a solid fit for yachts and commercial builds over 50m where a 3nm, double white all-round light is part of the navigation light plan.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e360° all-round white light with double-stacked output, rated for 3 nautical miles\u003c\/li\u003e\n\u003cli\u003e10-32VDC input for 12V and 24V systems; 4.2W draw (270mA at 12V, 176mA at 24V)\u003c\/li\u003e\n\u003cli\u003eIP68-rated sealing for weather exposure, washdowns, and saltwater operation\u003c\/li\u003e\n\u003cli\u003eHorizontal mounting on an aluminum base with cable routing option to the side or straight down\u003c\/li\u003e\n\u003cli\u003eCompact footprint (Ø92.5mm x 96.5mm) with a 1.31kg assembly weight\u003c\/li\u003e\n\u003cli\u003ePlug connector connection for clean integration into a nav-light harness\u003c\/li\u003e\n\u003cli\u003eSilver anodized aluminum finish (25µ) with PMMA lens and A4 stainless fasteners\u003c\/li\u003e\n\u003cli\u003eApproved to COLREG72, EN14744, IEC 60945, IACS E10, USCG, ABS, M.E.D., DNV, and LR\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eWhat’s included\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eNavigation light assembly with aluminum base\u003c\/li\u003e\n\u003cli\u003eHDPE base plate\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and wiring\u003c\/h6\u003e\u003cp\u003ePlan the mounting spot so the light has a true 360° view with as little blockage as possible from antennas, domes, stays, or hardtops. Because the unit is specified for horizontal mounting, install it on a level surface and tighten fasteners evenly to keep the base sitting flat.\u003c\/p\u003e\u003cp\u003ePower is DC in the 10-32V range. The minimum feed wire gauge is 0.5mm2 (AWG22). Use a protected navigation-light circuit, keep connections dry inside the mast or structure, and route the cable away from heat and high-current motor runs where practical.\u003c\/p\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis light is intended for vessels over 50m and is commonly used in setups that call for a double white all-round light arrangement. Verify your vessel’s navigation-light plan and mounting height requirements before drilling, especially on commercial builds where the light arrangement is tied to compliance documentation.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eRinse salt residue from the housing and lens as part of regular washdowns and wipe the lens with a soft cloth to keep the light output clean. Periodically check fasteners for tightness and inspect the connector for a secure, dry fit after heavy weather or mast work.\u003c\/p\u003e","brand":"Lopolight","offers":[{"title":"Default Title","offer_id":52269749108917,"sku":"QBP076742","price":2274.24,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1301216_qbp076742.png?v=1771545532"},{"product_id":"qbp166668","title":"Lopolight K-Lock to FB Nav Light Adaptor, Version 2, Waterproof Seal, Excludes 180 Deg Lights","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Lopolight 400-407 is a K-lock to FB adaptor that lets an FB-type navigation light mount onto a K-Lock base, excluding the 180-degree light versions.\u003c\/p\u003e\u003cp\u003eIt is a mechanical mounting part with no electrical load on the boat: current consumption is 0 mA at 12 VDC and 24 VDC. The Version 2 interface is made to seal between the light and the K-Lock base, which helps keep water out of the joint where spray, washdowns, and vibration tend to work on fittings.\u003c\/p\u003e\u003cp\u003eFor fit planning, the adaptor has an outside diameter of 92.5 mm and an overall height of 18.2 mm. The body is POM (acetal), so it will not corrode in saltwater environments.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eMounts an FB-type Lopolight navigation light onto a standard K-Lock base (not for 180-degree light versions)\u003c\/li\u003e\n\u003cli\u003eVersion 2 sealing interface between the light and the K-Lock base for a watertight joint\u003c\/li\u003e\n\u003cli\u003eMechanical accessory with 0 mA draw at 12 VDC and 24 VDC\u003c\/li\u003e\n\u003cli\u003e92.5 mm outside diameter and 18.2 mm overall height to help confirm clearance at the mounting location\u003c\/li\u003e\n\u003cli\u003ePOM (acetal) construction that will not corrode in marine environments\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis adaptor is for installations that have a K-Lock mounting base in place and need to use an FB-type navigation light. It is not intended for K-Lock bases used with 180-degree light configurations.\u003c\/p\u003e\u003cp\u003eBefore ordering, confirm the base style on the boat and the light interface type. The adaptor footprint is 92.5 mm across, so check for nearby hardware, rails, or mast fittings that could interfere with the lock-in action.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eInstallation is straightforward: the adaptor locks onto the K-Lock base, and the FB-type light mounts to the adaptor in the same position it would normally use for the FB interface. Make sure the mating surfaces are clean so the seal seats properly.\u003c\/p\u003e\u003cp\u003eAfter mounting, verify the light is locked fully and oriented correctly for its required arc of visibility. A quick hose-down check around the joint is a sensible final step on open deck and mast installations.\u003c\/p\u003e\u003ch6\u003eOn-board use notes\u003c\/h6\u003e\u003cp\u003eThis is a practical part for refits where you want to keep existing K-Lock bases but change the light style at the mounting point. It also suits yards and owners standardizing mounting bases across a vessel while still using FB-type lights where that interface is needed.\u003c\/p\u003e","brand":"Lopolight","offers":[{"title":"Default Title","offer_id":52269754876085,"sku":"QBP166668","price":145.78,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1301265_qbp166668.png?v=1771545574"},{"product_id":"qbp270664","title":"Lopolight PRO Ice-Class Double LED Navigation Light, 19-32 VDC, IP68, 25W De-Icing Heater, Horizontal Mount","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Lopolight Double Stacked Ice-Class navigation light is a horizontally mounted, IP68-rated LED navigation light built with a de-icing heater for cold-weather operations. Ice-class versions run on 19 to 32 VDC, and the built-in 25 W heater is controlled by an internal temperature sensor that activates below 3°C and switches off at 15°C.\u003c\/p\u003e\u003cp\u003eEach unit contains two independent light modules, a primary and a secondary, that can be powered separately through the 5-pin connector. The housing is machined from 6082 aluminum with an anodized finish, and the interior is fully potted to help keep water and vibration from reaching the electronics.\u003c\/p\u003e\u003cp\u003eThis range is typically specified for vessels over 50 m (164 ft) and is used where certified navigation lighting needs to stay visible in heavy spray and freezing conditions. The exact light sector, color, and visibility rating depend on the configuration listed below.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eDouble light with separate primary and secondary power paths for redundancy (5-pin connection with dedicated power and ground for each light)\u003c\/li\u003e\n\u003cli\u003eIce-class de-icing with a 25 W heating element and temperature sensor control (on below 3°C, off at 15°C)\u003c\/li\u003e\n\u003cli\u003e19 to 32 VDC input range for the ice-class configurations\u003c\/li\u003e\n\u003cli\u003eIP68 sealing with fully potted electronics for washdown exposure and vibration\u003c\/li\u003e\n\u003cli\u003eHorizontal mounting on a 400-037 aluminum base with an HDPE base plate\u003c\/li\u003e\n\u003cli\u003eSide cable entry with two M25x1.5 threaded gland ports for clean routing\u003c\/li\u003e\n\u003cli\u003eMeets COLREG72, EN14744, IEC 60945, and USCG (UL1104) requirements\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eVariants\u003c\/h6\u003e\u003cp\u003eThis product is offered in multiple configurations to match different navigation-light positions and visibility requirements.\u003c\/p\u003e\u003cp\u003eAcross the range, the double primary and secondary layout, ice-class de-icing approach, IP68 sealing, and horizontal mounting style remain consistent. The light sector, light color, and visibility rating vary by configuration.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e300-138-PRO-I: Nanometers 6NM. 225° white masthead light with visibility rated for more than 6 nautical miles; power consumption is 7 W in normal operation and 32 W during de-icing at 24 VDC.\u003c\/li\u003e\n\u003cli\u003e301-108ST-PRO-I: Nanometers 3NM. 112.5° green starboard sidelight with visibility rated for more than 3 nautical miles; power consumption is 2.3 W in normal operation and 27.3 W during de-icing at 24 VDC.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eWhat’s included\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eNavigation light mounted on 400-037 aluminum base\u003c\/li\u003e\n\u003cli\u003eHDPE base plate\u003c\/li\u003e\n\u003cli\u003e3 x M6x14 mounting screws\u003c\/li\u003e\n\u003cli\u003e2 x M25x1.5 cable glands for 9 to 17 mm cable diameter\u003c\/li\u003e\n\u003cli\u003e5-pin connector plug\u003c\/li\u003e\n\u003cli\u003e2 x reduction kits (M25 to M20 or M16) for 4.5 to 13 mm cable diameter\u003c\/li\u003e\n\u003cli\u003eInstallation instructions\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and mounting\u003c\/h6\u003e\u003cp\u003eThese lights are built for horizontal mounting, with the cable glands entering from the side. Plan the mounting surface so the base sits flat, and confirm the light’s sector orientation matches the vessel centerline and required navigation-light position.\u003c\/p\u003e\u003cp\u003eUse the included glands and reduction pieces to match your cable diameter and keep the seal intact. Leave enough service loop and clearance to access the connector and gland area without stressing the wiring.\u003c\/p\u003e\u003ch6\u003eElectrical and system integration\u003c\/h6\u003e\u003cp\u003eIce-class configurations operate on 19 to 32 VDC. The connector supports separate power and ground for the primary and secondary light circuits, which helps when the installation calls for redundancy or independent monitoring of each light module.\u003c\/p\u003e\u003cp\u003eAccount for the higher current draw during de-icing when sizing wiring and protection. At 24 VDC, the 6NM masthead configuration draws about 0.29 A normally and about 1.3 A when heating, while the 3NM starboard configuration draws about 0.18 A normally and about 1.1 A when heating.\u003c\/p\u003e\u003ch6\u003eUse on board\u003c\/h6\u003e\u003cp\u003eThis range is a good match for commercial vessels, superyachts, and expedition boats that run in freezing spray or ice-prone waters and still need navigation lights that stay visible and correctly sectored. It also suits high-vibration installations where potted electronics and IP68 sealing matter.\u003c\/p\u003e\u003ch6\u003eMaintenance and inspection\u003c\/h6\u003e\u003cp\u003eRinse salt buildup from the housing and gland area as part of normal deck washdowns, and check that cable glands remain tight after seasonal temperature swings. In cold climates, periodic visual checks of the light sector and lens area help confirm the de-icing function is keeping the optics clear.\u003c\/p\u003e","brand":"Lopolight","offers":[{"title":"6NM","offer_id":52270723465397,"sku":"QBP270664-V1","price":3783.84,"currency_code":"USD","in_stock":true},{"title":"3NM","offer_id":52270723498165,"sku":"QBP270664-V2","price":2372.75,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1303693_qbp270664.png?v=1771550634"},{"product_id":"qbp274841","title":"Lopolight Stern\/360° Navigation Light, 2NM, White Light, FB Base, 10-32VDC, IP68","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThis Lopolight 360-degree stern light with an FB base is a white navigation light rated for 2 nautical miles on vessels under 12 m. It runs on 10-32 VDC for 12V and 24V systems and draws 3 W (300 mA at 12 VDC, 148 mA at 24 VDC).\u003c\/p\u003e\u003cp\u003eThe FB (flat base) centers the wiring for antenna-style pole mountings and also supports deck mounting from above or from below when you want a lower profile. The light is sealed to IP68 and comes pre-cabled with a 0.75 m shielded marine cable, with a minimum feed wire gauge of 0.5 mm2 (AWG22) for the supply run.\u003c\/p\u003e\u003cp\u003eOverall size is Ø92.5 mm x 36 mm, with horizontal mounting. Operating temperature range is -25C to 55C, and approvals include COLREG72, EN14744, IEC 60945, IACS E10, USCG, ABS, M.E.D., DNV, and LR.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e360-degree white stern\/anchor-style visibility rated to 2 nautical miles for vessels under 12 m\u003c\/li\u003e\n\u003cli\u003eWide 10-32 VDC input for mixed 12V and 24V onboard systems\u003c\/li\u003e\n\u003cli\u003e3 W draw with published current figures (300 mA at 12 VDC, 148 mA at 24 VDC) for straightforward circuit sizing\u003c\/li\u003e\n\u003cli\u003eIP68 sealing for exposed mounting where spray and washdowns are part of normal use\u003c\/li\u003e\n\u003cli\u003eFB flat base routes wiring through the center for pole mounts and supports mounting from above or from below\u003c\/li\u003e\n\u003cli\u003eCompact footprint (Ø92.5 mm x 36 mm) with a pre-attached 0.75 m shielded cable\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eVariants\u003c\/h6\u003e\u003cp\u003eThis light is offered with two housing color options while keeping the same 2 nm rating, electrical range, and overall form factor.\u003c\/p\u003e\u003cp\u003eAcross the range, the light color remains white with 360-degree coverage, mounting stays horizontal, the sealing level is IP68, and power is 10-32 VDC at 3 W. The practical difference between variants is the housing finish for how it looks on the boat.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e201-030-FB-B: Housing color Black. The black anodized housing blends into dark poles, arches, and canvas-heavy setups where you want the light to stay visually low-key.\u003c\/li\u003e\n\u003cli\u003e201-030-FB: Housing color Silver. The silver anodized housing matches stainless hardware and aluminum structures and keeps a classic look on deck.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eWhat’s included\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eNavigation light with attached 0.75 m shielded marine cable\u003c\/li\u003e\n\u003cli\u003eInstallation guide\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003ePlan for a horizontal mounting surface at the stern, radar arch, or on a suitable pole, with a clear view around the horizon. The FB base is set up for centered cable routing, which keeps the wiring protected when it runs down a tube or through a deck pass-through.\u003c\/p\u003e\u003cp\u003eFor mounting from the top, the base uses three clearance holes (3 x Ø4.4 mm) spaced 120 degrees apart. For mounting from below, the base provides three threaded holes (3 x M4 x 0.7, 6 mm deep). Route and secure the cable to avoid chafe, and seal any deck penetrations appropriately for your mounting location.\u003c\/p\u003e\u003ch6\u003eElectrical and system integration\u003c\/h6\u003e\u003cp\u003eConnect to a switched navigation-light circuit on 10-32 VDC. When extending the factory lead, keep splices dry, use marine-grade connectors, and support the cable so vibration does not work the joint loose over time.\u003c\/p\u003e\u003cp\u003eUse the published current draw when sizing protection and wiring for the run. On a 12V boat, plan around 300 mA for the fixture itself before considering voltage drop over longer cable lengths.\u003c\/p\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis unit is a good match for small sailboats and powerboats under 12 m that need a 2 nm all-round white light on a stern pole, aft rail, arch, or a clean deck mount. It is also a practical choice for coastal cruising boats that spend time at anchor and want a light that holds up in spray and sun.\u003c\/p\u003e\u003ch6\u003eMaterials and sealing\u003c\/h6\u003e\u003cp\u003eThe housing is anodized aluminum with a PMMA lens and A4 stainless steel screws. The enclosure is rated to IP68, which matters when the light lives outside where salt, rain, and routine washdowns are normal.\u003c\/p\u003e","brand":"Lopolight","offers":[{"title":"Black","offer_id":52270728216757,"sku":"QBP274841-V1","price":740.51,"currency_code":"USD","in_stock":true},{"title":"Silver","offer_id":52270728249525,"sku":"QBP274841-V2","price":740.51,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1303756_qbp274841.jpg?v=1771550662"},{"product_id":"qbp275081","title":"Lopolight Masthead\/Anchor LED Navigation Light, For Vessels Under 12m, 2NM, White LED, FB Base, 10-32VDC, IP68, Horizontal Mount","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Lopolight Masthead\/360-Degree Light is an all-round (360-degree) white navigation light rated for 2 nautical miles (2 NM). It runs on 10-32 VDC (12V or 24V systems) and draws 3 W (about 225 mA at 12 V and 156 mA at 24 V).\u003c\/p\u003e\u003cp\u003eThis version uses an FB (flat base) mounting system for horizontal installation. The housing measures Ø92.5 mm x 36 mm and is sealed to IP68, which suits exposed mast, arch, or pole locations that see spray and washdowns.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e2 NM all-round (360-degree) white navigation light for masthead or anchor-light use where an all-round white is required\u003c\/li\u003e\n\u003cli\u003e10-32 VDC input with a 3 W draw for straightforward use on 12V or 24V boats\u003c\/li\u003e\n\u003cli\u003eIP68 sealing for wet mounting locations and regular deck washdowns\u003c\/li\u003e\n\u003cli\u003eFB (flat base) POM mounting system with centered cable routing for clean pole or deck installations\u003c\/li\u003e\n\u003cli\u003ePre-cabled with a 0.75 m shielded marine-grade lead; minimum feed wire gauge 0.5 mm2 (AWG 22)\u003c\/li\u003e\n\u003cli\u003eHorizontal mounting with a low-profile footprint (Ø92.5 mm x 36 mm) and a listed weight of about 0.46 kg\u003c\/li\u003e\n\u003cli\u003eApproved to COLREG72, EN14744, IEC 60945, IACS E10, USCG, ABS, M.E.D., DNV, and LR\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eVariants\u003c\/h6\u003e\u003cp\u003eThis light is offered in multiple configurations that change the housing color.\u003c\/p\u003e\u003cp\u003eElectrical ratings, IP68 sealing, dimensions, and approvals stay the same across the variants; the difference is the exterior finish.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e201-020-FB-B: Housing color Black. A darker finish pairs naturally with black anodized spars, radar arches, and many antenna mounts.\u003c\/li\u003e\n\u003cli\u003e201-020-FB: Housing color Silver. A silver finish matches bare aluminum masts, polished metalwork, and classic deck hardware.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eThe unit mounts horizontally on the FB base, with wiring routed through the center of the base for a tidy run into a pole, hardtop, or deck. Plan the cable path before bedding the base so the lead stays protected and does not chafe on sharp edges.\u003c\/p\u003e\u003cp\u003eMounting can be done from the top using three clearance holes (3x Ø4.4 mm), or from underneath using three threaded holes (3x M4 x 0.7, 6 mm deep). This makes it easier to keep a clean top surface when you have access below the mounting panel.\u003c\/p\u003e\u003ch6\u003eElectrical and system integration\u003c\/h6\u003e\u003cp\u003eConnect to a fused 10-32 VDC lighting circuit and follow your vessel’s wiring practices for navigation lights. Use at least 0.5 mm2 (AWG 22) feed wiring and keep connections dry and strain-relieved in the mast base, arch, or overhead where the cable transitions into the boat.\u003c\/p\u003e\u003cp\u003eThe low power draw is helpful on boats that spend long nights at anchor or run with lights on for extended evening transits, without adding much load to the house bank.\u003c\/p\u003e\u003ch6\u003eMaterials and corrosion resistance\u003c\/h6\u003e\u003cp\u003eThe housing is anodized aluminum with a PMMA lens and A4 stainless steel fasteners. Combined with the IP68 seal, this construction suits exposed saltwater installations where the light sees spray, vibration, and routine cleaning.\u003c\/p\u003e\u003ch6\u003eWhat’s included\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eNavigation light pre-cabled with a 0.75 m shielded marine-grade cable\u003c\/li\u003e\n\u003cli\u003eInstallation guide\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eUse cases on board\u003c\/h6\u003e\u003cp\u003eThis is a good match for small powerboats and sailboats that need an all-round white light on a mast, radar arch, or antenna pole, and want a low-profile base that keeps wiring centered and out of sight.\u003c\/p\u003e","brand":"Lopolight","offers":[{"title":"Black","offer_id":52270728806581,"sku":"QBP275081-V1","price":740.51,"currency_code":"USD","in_stock":true},{"title":"Silver","offer_id":52270728839349,"sku":"QBP275081-V2","price":740.51,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1303759_qbp275081.jpg?v=1771550663"},{"product_id":"qbp468122","title":"Lopolight Series 201-007 Tri-Color Navigation\/Anchor Light, 2 NM, 10-32VDC, IP68, Horizontal Mount","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Lopolight 201-007 Series is a horizontal-mount masthead light that combines a 2 NM tri-color navigation light with a 360° anchor light, with variants that add either a Windex light or a strobe function.\u003c\/p\u003e\u003cp\u003eIt runs on 10-32 VDC for 12 V and 24 V systems and carries an IP68 rating for exposed masthead mounting. The light body is Ø92.5 mm, with overall height varying by configuration (roughly 68 to 86 mm).\u003c\/p\u003e\u003cp\u003eThis series is sized for vessels in the 12-20 m range (about 39-66 ft) where it helps reduce the number of separate fixtures at the top of the mast.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e2 NM visibility with tri-color navigation sectors and a separate 360° anchor light circuit.\u003c\/li\u003e\n\u003cli\u003e10-32 VDC input for common 12 V and 24 V onboard power systems.\u003c\/li\u003e\n\u003cli\u003eIP68 rating for wet environments, spray, and routine washdowns.\u003c\/li\u003e\n\u003cli\u003eHorizontal mount format; Ø92.5 mm body with overall height that depends on the configuration (about 68-86 mm).\u003c\/li\u003e\n\u003cli\u003eSilver or black anodized aluminum housing with PMMA lens and A4 stainless steel fasteners.\u003c\/li\u003e\n\u003cli\u003eApprovals listed for COLREG72 and EN14744, with IEC 60945 and USCG (UL1104) compliance referenced for the range.\u003c\/li\u003e\n\u003cli\u003eConnection options include 0.75 m pre-cabled versions, 30 m long-cable versions for mast pulls, and a connector-base option with a 4-14 mm cable gland.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eVariants\u003c\/h6\u003e\u003cp\u003e201-007 Series lights are offered in multiple configurations so you can match the function set at the masthead and the way you want to route wiring down the spar.\u003c\/p\u003e\u003cp\u003eAcross the range, the units mount horizontally, run on 10-32 VDC, and are rated for 2 NM visibility. The main differences are whether the third function is a Windex light or a strobe circuit, and whether the light is supplied with a short lead, a long lead, or a connector base for your own cable.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e201-007G2SW: Style Tri-Color Navigation\/Anchor\/Windex Light; Housing Silver Housing; Cable 0.75M Cable. This adds an illuminated Windex mount at the masthead for night trims without adding a separate light.\u003c\/li\u003e\n\u003cli\u003e201-007G2S: Style Tri-Color Navigation\/Anchor\/Strobe Light; Housing Silver Housing; Cable 0.75M Cable. The extra circuit is a strobe function intended for special signaling rather than routine navigation light use.\u003c\/li\u003e\n\u003cli\u003e201-007S-B TB: Style Tri-Color Navigation\/Anchor\/Strobe Light; Housing Black Housing; Cable 4-14mm. This uses a connector-style base and cable gland so you can terminate your own mast cable while keeping the connection protected at the masthead.\u003c\/li\u003e\n\u003cli\u003e201-007G2S-30M: Style Tri-Color Navigation\/Anchor\/Strobe Light; Housing Silver Housing; Cable 30M. A long lead suits full mast re-wires where you want one continuous run down to the switching panel.\u003c\/li\u003e\n\u003cli\u003e201-007G2SW-30M: Style Tri-Color Navigation\/Anchor\/Windex Light; Housing Silver Housing; Cable 30M. This keeps the Windex light function while using a long cable for mast pulls and refits.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eWhat’s included\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eNavigation light assembly (with the cable or connection style specified by the selected variant)\u003c\/li\u003e\n\u003cli\u003eInstallation guide\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eMount the light horizontally on the masthead so the lens has a clear view around the boat, without shadowing from antennas, wind instruments, or rigging. Plan the mounting location so the unit sits on the boat centerline and remains accessible for service.\u003c\/p\u003e\u003cp\u003eFor pre-cabled versions, route the lead down the mast with chafe protection and secure it so it cannot slap inside the spar. A minimum feed wire gauge of 0.5 mm2 (AWG 22) is noted for the series; longer cable runs may require heavier wire depending on your switch panel location and voltage drop targets.\u003c\/p\u003e\u003ch6\u003eElectrical and switching\u003c\/h6\u003e\u003cp\u003eThese lights use separate circuits for the different functions, which allows you to switch between tri-color, anchor, and the Windex or strobe function as needed. Use appropriately fused, switched feeds for each function and a common return, and follow your vessel’s wiring practices for strain relief, drip loops, and sealed penetrations.\u003c\/p\u003e\u003ch6\u003eUse on board\u003c\/h6\u003e\u003cp\u003eThis series is a good match for sailboats in the 39-66 ft range that want a single masthead fixture covering underway and at-anchor lighting, while keeping the masthead layout tidy. The 30 m cable variants are helpful when the mast is coming down and you want to replace the full run in one pass.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eRinse salt residue from the housing and lens during routine washdowns and keep the lens free of grime that can block light output. During periodic rig checks, inspect mounting fasteners and cable condition at the mast exit points and any deck glands.\u003c\/p\u003e","brand":"Lopolight","offers":[{"title":"Tri-Color Navigation\/Anchor\/Windex Light \/ Silver Housing \/ 0.75M Cable","offer_id":52271117893813,"sku":"QBP468122-V1","price":1431.89,"currency_code":"USD","in_stock":false},{"title":"Tri-Color Navigation\/Anchor\/Strobe Light \/ Silver Housing \/ 0.75M Cable","offer_id":52271117926581,"sku":"QBP468122-V2","price":1250.78,"currency_code":"USD","in_stock":false},{"title":"Tri-Color Navigation\/Anchor\/Strobe Light \/ Black Housing \/ 4-14mm","offer_id":52271117959349,"sku":"QBP468122-V3","price":1294.56,"currency_code":"USD","in_stock":true},{"title":"Tri-Color Navigation\/Anchor\/Strobe Light \/ Silver Housing \/ 30M","offer_id":52271117992117,"sku":"QBP468122-V4","price":1630.36,"currency_code":"USD","in_stock":false},{"title":"Tri-Color Navigation\/Anchor\/Windex Light \/ Silver Housing \/ 30M","offer_id":52271118024885,"sku":"QBP468122-V5","price":1811.52,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1307361_qbp468122.jpg?v=1771552988"},{"product_id":"qbp592635","title":"Lopolight Stern Light, LED, 2NM, 10-32V, IP68, Horizontal Mount","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Lopolight 301-005 Series Stern Light is a 135° white stern navigation light rated for 2 nautical miles of visibility, with a horizontal-mount footprint for aft installations on vessels up to 50 m (164 ft). It runs on 10-32 VDC, so it fits both 12 V and 24 V electrical systems, and the housing is built for exposed mounting where salt spray, washdowns, and vibration are normal.\u003c\/p\u003e\u003cp\u003eThis series is used when you want a compact stern light that meets the common navigation-light standards for larger yachts and cruisers. The light output is focused through PMMA optics, and the internal electronics are fully potted to help keep water out and reduce failures from vibration.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e2 nautical mile, 135° stern light output for vessels up to 50 m (164 ft).\u003c\/li\u003e\n\u003cli\u003eHorizontal mounting format suited to transoms, aft rails, and aft superstructure faces where the stern sector stays clear.\u003c\/li\u003e\n\u003cli\u003e10-32 VDC input supports both 12 V and 24 V onboard systems.\u003c\/li\u003e\n\u003cli\u003eIP68-rated build with fully potted electronics to handle washdowns and long-term vibration.\u003c\/li\u003e\n\u003cli\u003eComplies with COLREG72, EN14744, IEC 60945, and USCG (UL1104) requirements.\u003c\/li\u003e\n\u003cli\u003eAvailable as single stack or double stack; double stack versions allow the two lights to be powered separately.\u003c\/li\u003e\n\u003cli\u003eFinish options include silver anodized, black anodized, and white ceramic-coated housings.\u003c\/li\u003e\n\u003cli\u003eCovered by a 5-year limited warranty.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eVariants\u003c\/h6\u003e\u003cp\u003eThis series is offered with two mounting styles and three finish options. Style changes between Single Stack and Double Stack, and finish changes between Silver, Black, and White.\u003c\/p\u003e\u003cp\u003eSingle Stack is a single stern light body. Double Stack combines two stern lights in one unit, with separate circuits so they can be controlled independently. The White finish uses a ceramic-coated housing, while Silver and Black finishes use anodized aluminum; wiring interface can vary by configuration, so match the connection style to how you plan to terminate wiring at the mounting point.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eMount the light where the 135° stern sector is not blocked by davits, outboards, antennas, or a swim platform. A small offset or a low mounting height can create shadows in the required sector, so it is worth checking sightlines from port and starboard aft before drilling.\u003c\/p\u003e\u003cp\u003eFor best results in saltwater, bed the fasteners and pass-through with marine sealant and support the cable so it does not flex at the housing. On aluminum and carbon structures, use proper isolation practices for dissimilar materials and follow the vessel builder’s corrosion-control approach.\u003c\/p\u003e\u003ch6\u003eElectrical and system integration\u003c\/h6\u003e\u003cp\u003ePower is 10-32 VDC, so this fits common DC buses without a converter. Use a properly protected circuit sized to the vessel’s wiring plan and route the cable away from ignition wiring and high-current runs where possible.\u003c\/p\u003e\u003cp\u003eOn Double Stack versions, plan for two independent feeds if you intend to control each light separately. Confirm how you will connect at the mounting point before installation, especially on tight transoms where access is limited.\u003c\/p\u003e\u003ch6\u003eUse cases on board\u003c\/h6\u003e\u003cp\u003eThis series suits yachts, sportfishers, and larger cruisers that need a 2 NM stern light in a compact housing, especially on boats that see regular washdowns or offshore vibration. It also fits refits where you are replacing older incandescent stern lights and want a modern footprint without reworking the vessel’s DC system.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eRinse salt off the lens and housing with fresh water and clean with mild soap to keep the optics clear. During routine checks, confirm the light is still aligned, the cable is strain-relieved, and the sealant around fasteners and cable exits is intact.\u003c\/p\u003e","brand":"Lopolight","offers":[{"title":"Silver \/ Single Stack","offer_id":52271515336885,"sku":"QBP592635-V1","price":479.66,"currency_code":"USD","in_stock":false},{"title":"Black \/ Single Stack","offer_id":52271515369653,"sku":"QBP592635-V2","price":479.66,"currency_code":"USD","in_stock":false},{"title":"White \/ Single Stack","offer_id":52271515402421,"sku":"QBP592635-V3","price":674.51,"currency_code":"USD","in_stock":false},{"title":"Silver \/ Double Stack","offer_id":52271515435189,"sku":"QBP592635-V4","price":0.0,"currency_code":"USD","in_stock":false},{"title":"Black \/ Double Stack","offer_id":52271515467957,"sku":"QBP592635-V5","price":0.0,"currency_code":"USD","in_stock":false},{"title":"White \/ Double Stack","offer_id":52271515500725,"sku":"QBP592635-V6","price":1134.97,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1309098_qbp592635.png?v=1771555157"},{"product_id":"qbp593640","title":"Lopolight 301-005 Series Stern Navigation Light, LED, 2NM, 135° White, Horizontal Mount, FB POM Flat Base, 10-32VDC, IP68","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Lopolight 301-005 Series is a 2 NM white stern navigation light (135°) for horizontal mounting with an FB (flat base) POM mounting system.\u003c\/p\u003e\u003cp\u003eIt runs on 10-32 VDC for 12 V and 24 V boats, with a 1.3 W draw (about 110 mA at 12 VDC and 50 mA at 24 VDC). Each configuration is supplied pre-cabled with a 2.5 m shielded marine-grade lead for straightforward tie-in to your navigation light circuit.\u003c\/p\u003e\u003cp\u003eThe enclosure is IP68 and built around an anodized aluminum body with a PMMA lens, which suits exposed stern locations that see spray, vibration, and regular washdowns. Approvals cover COLREG72 and USCG requirements for vessels up to 50 m (164 ft), along with EN14744, IEC 60945, and IACS E10.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e2 NM white stern light with a 135° sector for vessels up to 50 m (164 ft)\u003c\/li\u003e\n\u003cli\u003e10-32 VDC input for 12 V and 24 V electrical systems\u003c\/li\u003e\n\u003cli\u003eIP68 sealing for wet stern installations and washdowns\u003c\/li\u003e\n\u003cli\u003ePre-cabled 2.5 m shielded marine-grade lead; minimum feed wire gauge 0.5 mm2 (AWG 22)\u003c\/li\u003e\n\u003cli\u003eHorizontal mounting with FB (flat base) POM mounting system\u003c\/li\u003e\n\u003cli\u003e1.3 W power draw (about 110 mA @ 12 VDC, 50 mA @ 24 VDC)\u003c\/li\u003e\n\u003cli\u003eOperating temperature range: -25°C to 55°C\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eVariants\u003c\/h6\u003e\u003cp\u003eThis stern light is offered in multiple configurations so you can match both the housing profile and the exterior finish around your mounting point.\u003c\/p\u003e\u003cp\u003eStyle is the main physical difference: Single Stack is Ø92.5 mm x 36 mm, while Double Stack is Ø92.5 mm x 58 mm. Across the range, the light output, voltage range (10-32 VDC), IP68 sealing, horizontal FB base mounting, and 2.5 m pre-cabled connection remain consistent.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e301-005-FB: Style Single Stack, Finish Silver. The lower 36 mm profile keeps the light close to the mounting surface when space is tight on a transom cap or stern rail base.\u003c\/li\u003e\n\u003cli\u003e301-005-FB-B: Style Single Stack, Finish Black. Same low-profile Single Stack body with a black finish that blends in on dark rails, arches, and transoms.\u003c\/li\u003e\n\u003cli\u003e301-005ST-FB: Style Double Stack, Finish Silver. The taller 58 mm body can help when the mounting point sits near rails or hardware that would otherwise encroach on the lens area.\u003c\/li\u003e\n\u003cli\u003e301-005ST-FB-B: Style Double Stack, Finish Black. Double Stack height with a black finish for installations where you want the light to visually disappear against darker trim.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eWhat’s included\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e1 navigation light (pre-cabled)\u003c\/li\u003e\n\u003cli\u003e2.5 m shielded marine-grade cable\u003c\/li\u003e\n\u003cli\u003eInstallation guide\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and wiring\u003c\/h6\u003e\u003cp\u003eMount the light so it has a clear, unobstructed view aft across the full 135° arc. On many boats this is on the transom, on the aft end of a hardtop, or on a stern rail base where the lens is not shadowed by antennas, rod holders, davits, or fenders.\u003c\/p\u003e\u003cp\u003ePlan the wire run so the connection stays dry and supported. Extend the supplied lead using tinned copper conductors and sealed splices, and keep a drip loop where the cable enters lockers or lazarettes. The current draw is low, but circuit protection should still follow your vessel’s wiring plan and standards.\u003c\/p\u003e\u003ch6\u003eMaterials and corrosion resistance\u003c\/h6\u003e\u003cp\u003eThe body is anodized aluminum with a PMMA lens and A4 stainless fasteners. With an IP68 seal, it fits well on stern locations that see salt spray and routine cockpit washdowns, as long as the mounting surface is flat and properly bedded.\u003c\/p\u003e\u003ch6\u003eOn-board use\u003c\/h6\u003e\u003cp\u003eThis is a good match for cruising sailboats and powerboats that need a 2 NM stern light and want one unit that works across 10-32 VDC. It also suits fishing boats where stern gear and spray are common, provided the mounting spot keeps the 135° sector clear.\u003c\/p\u003e","brand":"Lopolight","offers":[{"title":"Single Stack \/ Silver","offer_id":52271515762869,"sku":"QBP593640-V1","price":507.88,"currency_code":"USD","in_stock":true},{"title":"Single Stack \/ Black","offer_id":52271515795637,"sku":"QBP593640-V2","price":507.88,"currency_code":"USD","in_stock":true},{"title":"Double Stack \/ Silver","offer_id":52271515828405,"sku":"QBP593640-V3","price":914.95,"currency_code":"USD","in_stock":false},{"title":"Double Stack \/ Black","offer_id":52271515861173,"sku":"QBP593640-V4","price":914.95,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1309105_qbp593640.png?v=1771555158"},{"product_id":"qbp595183","title":"Lopolight Tri-Color\/Anchor Navigation Light, 1NM, FB Base, 10-32VDC, IP68","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Lopolight Tri-Color Anchor Light - 1NM, with FB Base is a combined masthead navigation light that gives you a tri-color sailing light and a 360° white anchor light in one unit. It runs on 10-32VDC, draws 2.6W, and is rated IP68 for wet, exposed mounting on a boat.\u003c\/p\u003e\u003cp\u003eThis model uses a horizontal FB (flat base) mount that keeps the footprint low and gives you clean cable routing through the center of the base for deck or pole-style installations. The housing diameter is Ø92.5mm with a 68mm height, and the light comes pre-cabled with a 0.75m shielded marine-grade lead.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eCombined tri-color and 360° anchor functions in one fixture for vessels under 12m\u003c\/li\u003e\n\u003cli\u003e1 nautical mile visibility rating\u003c\/li\u003e\n\u003cli\u003eWide-input 10-32VDC operation for 12V and 24V electrical systems\u003c\/li\u003e\n\u003cli\u003eLow power draw: 2.6W (150mA at 12VDC, 81mA at 24VDC)\u003c\/li\u003e\n\u003cli\u003eIP68-rated for rain, spray, and washdowns when properly installed\u003c\/li\u003e\n\u003cli\u003eHorizontal FB base with centered cable exit for a tidy, low-profile mount\u003c\/li\u003e\n\u003cli\u003ePre-cabled with 0.75m shielded marine-grade cable; minimum feed wire gauge 0.5mm² (AWG22)\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eVariants\u003c\/h6\u003e\u003cp\u003eThis light is offered in multiple configurations based on housing finish.\u003c\/p\u003e\u003cp\u003eThe finish changes between variants. The light functions, 1NM visibility, 10-32VDC electrical range, dimensions, cable length, and FB base mounting style remain the same.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e101-009-FB (Finish: Silver). A clean visual match for aluminum spars, radar poles, and bright topside hardware.\u003c\/li\u003e\n\u003cli\u003e101-009-FB-B (Finish: Black). A darker look that stays visually low-profile on black spars and modern rigging packages.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eWhat’s included\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eNavigation light\u003c\/li\u003e\n\u003cli\u003e0.75m shielded marine-grade cable (pre-attached)\u003c\/li\u003e\n\u003cli\u003eInstallation guide\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eMount it horizontally using the FB base, with either a top screw-down installation or a from-below mount depending on how your masthead, pole, or mounting pad is built. Plan for a clear 360° line of sight and keep it away from antennas, wind instruments, or other fittings that can shadow the beam.\u003c\/p\u003e\u003cp\u003eBecause the cable exits through the center of the base, it routes neatly through a masthead plate or inside a pole. On open deck mounts, seal fasteners and cable penetrations to prevent water tracking into the core or wiring chase.\u003c\/p\u003e\u003ch6\u003eElectrical and switching\u003c\/h6\u003e\u003cp\u003eThe unit operates on DC systems from 10 to 32 volts and draws 150mA at 12VDC or 81mA at 24VDC. Size the feed wiring to at least 0.5mm² (AWG22) and route the cable where it will not be pinched by mast movement, hinges, or folding mechanisms.\u003c\/p\u003e\u003cp\u003eIt is a combined tri-color and anchor light, so your switch panel should be set up so the correct navigation mode is selected without running both functions at the same time.\u003c\/p\u003e\u003ch6\u003eOn-board use and fit check\u003c\/h6\u003e\u003cp\u003eThis style of combined light is a common choice on sailboats up to 12 meters where you want tri-color navigation lighting under sail and a dedicated all-round white anchor light at night without adding separate fixtures. It also suits small craft that need a compact, low-draw light at the top of a pole or mast where vibration and weather exposure are constant.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eRinse the housing after saltwater runs and washdowns, and keep the lens clean so the light sectors stay sharp. During seasonal checks, inspect the cable for chafe at entry points and confirm fasteners remain snug after heavy weather or trailering.\u003c\/p\u003e","brand":"Lopolight","offers":[{"title":"Silver","offer_id":52271515959477,"sku":"QBP595183-V1","price":740.51,"currency_code":"USD","in_stock":true},{"title":"Black","offer_id":52271515992245,"sku":"QBP595183-V2","price":740.51,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1309110_qbp595183.png?v=1771555159"},{"product_id":"qbp596793","title":"Lopolight Stern Navigation Light, LED, 3 NM, 135° Beam, Horizontal Mount, 10-32VDC, IP68, For Vessels Over 50m","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Lopolight 301-105 Series is a 3 NM, 135° white stern navigation light range for horizontal mounting on vessels over 50 m (164 ft).\u003c\/p\u003e\u003cp\u003eThese lights run on 10-32 VDC, so they fit typical 12V and 24V onboard systems without converters. The housing is IP68-rated for exposed stern locations, and the connection is via a plug connector for a clean install and service access.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e3 NM visibility with 135° stern coverage in white for vessels over 50 m (164 ft)\u003c\/li\u003e\n\u003cli\u003e10-32 VDC input for common 12V and 24V DC systems\u003c\/li\u003e\n\u003cli\u003eIP68 sealing for transom installs exposed to spray and washdowns\u003c\/li\u003e\n\u003cli\u003ePlug connector connection; minimum feed wire gauge listed as 0.5 mm2 (AWG 22)\u003c\/li\u003e\n\u003cli\u003eOperating temperature range: -25°C to 55°C\u003c\/li\u003e\n\u003cli\u003eAluminum housing options by finish, with a PMMA lens and A4 stainless steel screws\u003c\/li\u003e\n\u003cli\u003eApprovals listed: COLREG72, EN14744, IEC 60945, IACS E10, USCG, ABS, M.E.D., DNV, LR\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eVariants\u003c\/h6\u003e\u003cp\u003eThis series is offered in three exterior finishes and two stack styles. Finish options are silver anodized aluminum, black anodized aluminum, or white ceramic coated aluminum.\u003c\/p\u003e\u003cp\u003eSingle stack models are Ø92.5 mm x 74.5 mm, and double stack models are Ø92.5 mm x 96.5 mm. Across the range, the light remains a horizontal-mount 3 NM, 135° white stern light with 10-32 VDC input, IP68 rating, and a plug connector.\u003c\/p\u003e\u003ch6\u003eInstallation and wiring\u003c\/h6\u003e\u003cp\u003eThis is a horizontal-mount stern light meant for a fixed installation at the aft end of the vessel where the 135° arc is clear of antennas, davits, and overhangs. On anodized versions, the cable can be routed to the side or out the bottom, which helps when you need to match existing cable runs and access panels.\u003c\/p\u003e\u003cp\u003ePlan a drip loop, keep connectors in a sheltered spot behind the mounting surface when possible, and protect the cable where it passes through metal or fiberglass. Use an appropriately protected navigation light circuit for your vessel, and verify polarity before final assembly.\u003c\/p\u003e\u003ch6\u003eCompatibility and compliance\u003c\/h6\u003e\u003cp\u003eThe 301-105 Series is built around the COLREG stern light requirement and is intended for larger yachts and commercial vessels where a 3 NM light is required. When replacing an existing light, confirm that the mounting location, visibility arc, and installation height remain compliant for your vessel and operating area.\u003c\/p\u003e\u003ch6\u003eMaterials and corrosion resistance\u003c\/h6\u003e\u003cp\u003eThe series uses an aluminum housing with either anodized or ceramic-coated finishes depending on the option selected. The lens is PMMA, and the fasteners are A4 stainless steel screws, which suits long-term exposure on deck and at the stern where salt, UV, and vibration are constant.\u003c\/p\u003e\u003ch6\u003eWhat’s included\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eNavigation light with plug connector\u003c\/li\u003e\n\u003cli\u003e2 mounting screws (M6 x 8 mm)\u003c\/li\u003e\n\u003cli\u003eInstallation guide\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Lopolight","offers":[{"title":"Silver \/ Single Stack","offer_id":52271516876981,"sku":"QBP596793-V1","price":1536.26,"currency_code":"USD","in_stock":true},{"title":"Black \/ Single Stack","offer_id":52271516909749,"sku":"QBP596793-V2","price":1536.26,"currency_code":"USD","in_stock":true},{"title":"White \/ Single Stack","offer_id":52271516942517,"sku":"QBP596793-V3","price":1861.23,"currency_code":"USD","in_stock":false},{"title":"Silver \/ Double Stack","offer_id":52271516975285,"sku":"QBP596793-V4","price":2511.59,"currency_code":"USD","in_stock":true},{"title":"Black \/ Double Stack","offer_id":52271517008053,"sku":"QBP596793-V5","price":2511.59,"currency_code":"USD","in_stock":true},{"title":"White \/ Double Stack","offer_id":52271517040821,"sku":"QBP596793-V6","price":2793.92,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1309129_qbp596793.png?v=1771555163"},{"product_id":"qbp597892","title":"Lopolight 360° Green Navigation Light, 2nm, Horizontal Mount, IP68","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Lopolight 201-015 is a 2 NM, 360° green LED navigation and signal light for horizontal mounting on an FB flat base.\u003c\/p\u003e\u003cp\u003eIt runs on 10-32 V DC for common 12 V and 24 V systems and draws 2.1 W. The housing is IP68-rated for exposed mounting points and is specified for operation from -25°C to 55°C.\u003c\/p\u003e\u003cp\u003eThe body measures Ø92.5 mm, and overall height depends on the stack style: 36 mm for single stack or 58 mm for double stack. Construction uses anodized aluminum with a PMMA lens and A4 stainless steel screws, and the light comes pre-cabled with a 0.75 m shielded marine-grade cable.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e2 NM visibility with a 360° green light output\u003c\/li\u003e\n\u003cli\u003eOperating voltage: 10-32 V DC\u003c\/li\u003e\n\u003cli\u003ePower draw: 2.1 W\u003c\/li\u003e\n\u003cli\u003eIP68 ingress protection for open-deck and superstructure mounting locations\u003c\/li\u003e\n\u003cli\u003eØ92.5 mm body diameter; 36 mm (single stack) or 58 mm (double stack) height\u003c\/li\u003e\n\u003cli\u003eMaterials: anodized aluminum housing, PMMA lens, A4 stainless steel screws\u003c\/li\u003e\n\u003cli\u003ePre-cabled with a 0.75 m shielded marine-grade cable\u003c\/li\u003e\n\u003cli\u003eOperating temperature: -25°C to 55°C\u003c\/li\u003e\n\u003cli\u003eMinimum feed wire gauge: 0.5 mm2 (AWG 22)\u003c\/li\u003e\n\u003cli\u003eApproved to COLREG72, EN14744, IEC 60945, IACS E10, and USCG\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eVariants\u003c\/h6\u003e\u003cp\u003eThis light is offered in two finishes and in single or double stacked styles.\u003c\/p\u003e\u003cp\u003eAcross the range, the light output stays 2 NM, 360° green with horizontal mounting, a 10-32 V DC input range, and an IP68 rating. Finish and stack style change the appearance and overall height.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e201-015-FB (Finish Silver, Single Stack). Lower overall height when clearance is limited under overhangs, antennas, or rails.\u003c\/li\u003e\n\u003cli\u003e201-015-FB-B (Finish Black, Single Stack). Same low-profile form factor with a black anodized look that blends into dark hardware and topside structures.\u003c\/li\u003e\n\u003cli\u003e201-015ST-FB (Finish Silver, Double Stack). Taller body with a double stacked layout when two green all-round lights are required at the same mounting point.\u003c\/li\u003e\n\u003cli\u003e201-015ST-FB-B (Finish Black, Double Stack). Double stacked configuration in a black finish for installations where a taller signal light stack is needed without changing the mounting footprint.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003ePlan the mounting location so the lens has an unobstructed 360° view. Rails, radomes, antennas, and the edge of a hardtop can mask the light if it sits too close or too low.\u003c\/p\u003e\u003cp\u003eRoute and secure the cable so it cannot chafe in vibration and so it stays clear of sharp edges. Bed fasteners and cable exits appropriately for the mounting surface, and isolate dissimilar metals when installing on aluminum structures.\u003c\/p\u003e\u003ch6\u003eCompatibility and use on board\u003c\/h6\u003e\u003cp\u003eThis all-round green light is used in specific navigation and signal configurations where a green 360° light is required. It suits owners and installers who need a compact, sealed unit that can live on an exposed arch, mast, or superstructure without constant attention.\u003c\/p\u003e\u003ch6\u003eWhat's included\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eNavigation light with pre-attached 0.75 m shielded cable\u003c\/li\u003e\n\u003cli\u003eInstallation guide\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Lopolight","offers":[{"title":"Silver \/ Single Stack","offer_id":52271517565109,"sku":"QBP597892-V1","price":664.03,"currency_code":"USD","in_stock":false},{"title":"Black \/ Single Stack","offer_id":52271517597877,"sku":"QBP597892-V2","price":664.03,"currency_code":"USD","in_stock":false},{"title":"Silver \/ Double Stack","offer_id":52271517630645,"sku":"QBP597892-V3","price":1193.41,"currency_code":"USD","in_stock":false},{"title":"Black \/ Double Stack","offer_id":52271517663413,"sku":"QBP597892-V4","price":1193.41,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1309135_qbp597892.png?v=1771555164"},{"product_id":"qbp598064","title":"Lopolight PRO 360 Deg Green Navigation Light, 2 NM, Ex Zone 1\/2, 10-32VDC, IP68","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Lopolight 201-015 PRO-EX is a 2 nm all-round green navigation and signal light built for horizontal mounting and hazardous-area installations. It runs on 10-32 VDC, draws 2 W, and carries an IP68 rating for wet decks and regular washdowns.\u003c\/p\u003e\u003cp\u003eThis is a 360° green light, so it is used when your vessel and local requirements call for an all-round green signal. The housing is black hard coat anodized aluminum (50µ) with a PMMA lens and A4 stainless steel screws, which suits exposed rail locations where salt spray and vibration are part of normal service.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e2 nm visibility with a 360° green light output\u003c\/li\u003e\n\u003cli\u003eCertified for use in ATEX Zone 1 and Zone 2, with IEC Ex Zone 1 certification\u003c\/li\u003e\n\u003cli\u003e10-32 VDC input for 12 V and 24 V systems, with 2 W power draw (160 mA @ 12 VDC, 107 mA @ 24 VDC)\u003c\/li\u003e\n\u003cli\u003eIP68-rated light and mounting base for weather exposure and washdowns\u003c\/li\u003e\n\u003cli\u003eHorizontal mounting format with side cable direction and a plug connector connection\u003c\/li\u003e\n\u003cli\u003eOperating temperature range of -25°C to 55°C\u003c\/li\u003e\n\u003cli\u003eMinimum feed wire gauge 0.5 mm2 (AWG22)\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eVariants\u003c\/h6\u003e\u003cp\u003eThis product is offered in multiple configurations to match different installation and operating conditions.\u003c\/p\u003e\u003cp\u003eAcross the range, the main differences are whether the light includes a built-in de-icing function and whether the body is a single stack or double stack format. The configurations share key electrical and environmental basics such as 10-32 VDC operation, 2 W draw, IP68 rating, plug connector connection, and a 2 nm all-round green output.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e201-015-PRO-EX: IEC Ex Zone 1 Certified, single stack. The single stack format keeps the overall height lower (Ø92.5 mm x 103.5 mm) for tighter mounting locations.\u003c\/li\u003e\n\u003cli\u003e201-015-PRO-I-EX: Built-in De-Icing Function \u0026amp; IEC Ex Zone 1 Certified, single stack. The integrated de-icing function supports operation in sub-zero conditions where ice buildup can block light output.\u003c\/li\u003e\n\u003cli\u003e201-015ST-PRO-EX: IEC Ex Zone 1 Certified, double stack. The double stack format increases the overall height (Ø92.5 mm x 125.5 mm) while keeping the same mounting style and visibility rating.\u003c\/li\u003e\n\u003cli\u003e201-015ST-PRO-I-EX: Built-in De-Icing Function \u0026amp; IEC Ex Zone 1 Certified, double stack. This pairs the taller double stack body with de-icing for cold-weather, hazardous-area service.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and wiring\u003c\/h6\u003e\u003cp\u003eThese lights are made for horizontal mounting on a dedicated aluminum base with the cable exiting to the side. Plan the mounting location so the lens has a clear 360° view and is not shadowed by antennas, rails, or work lights.\u003c\/p\u003e\u003cp\u003eProtect the supply circuit with a 2A fast fuse with a breaking capacity of at least 1500A, or supply the light through a navigation light controller that provides equivalent short-circuit protection. Cable glands and a ground strap are not included, so specify the correct sealing and bonding parts for your vessel and classification requirements.\u003c\/p\u003e\u003ch6\u003eCompatibility and use on board\u003c\/h6\u003e\u003cp\u003eThis light is approved to COLREG72 and EN14744 and is also approved to IEC 60945 and IACS E10, with USCG and ATEX\/IEC 60079 approvals listed for the PRO-EX range. It is a good match for commercial vessels and workboats that need a certified all-round green signal light and want a compact, straightforward install that holds up on exposed rails and platforms.\u003c\/p\u003e\u003ch6\u003eWhat's included\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e1 navigation light\u003c\/li\u003e\n\u003cli\u003eInstallation guide\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Lopolight","offers":[{"title":"IEC Ex Zone 1 Certified \/ Single Stack","offer_id":52271517958325,"sku":"QBP598064-V1","price":1255.98,"currency_code":"USD","in_stock":false},{"title":"Built-in De-Icing Function \u0026 IEC Ex Zone 1 Certified \/ Single Stack","offer_id":52271517991093,"sku":"QBP598064-V2","price":2340.63,"currency_code":"USD","in_stock":false},{"title":"IEC Ex Zone 1 Certified \/ Double Stack","offer_id":52271518023861,"sku":"QBP598064-V3","price":2021.94,"currency_code":"USD","in_stock":false},{"title":"Built-in De-Icing Function \u0026 IEC Ex Zone 1 Certified \/ Double Stack","offer_id":52271518056629,"sku":"QBP598064-V4","price":3768.05,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1309140_qbp598064.png?v=1771555166"},{"product_id":"qbp598948","title":"Lopolight 200-018 180 Deg LED Navigation Light, Green Light, 2nm, Vertical Mount, 10-32VDC, IP68, Anodized Aluminum, COLREG72, USCG","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Lopolight 200-018 Series is a 2 NM, 180° green navigation light for vertical mounting, built for vessels up to 50 m (164 ft) and wired to 10-32 VDC (12 V or 24 V systems). It draws about 1.5 W (145 mA at 12 V, 60 mA at 24 V) and carries an IP68 rating for exposed mounting locations.\u003c\/p\u003e\u003cp\u003eThe housing is anodized aluminum with a PMMA lens, and the electronics are potted to handle spray and vibration. The footprint is roughly 104 mm wide by 46 mm deep, which helps when you are fitting it on a cabin side, bulwark, or other tight vertical surface.\u003c\/p\u003e\u003cp\u003eSingle stack versions house one light element. Double stack versions combine two independent light elements in one stacked body, which makes it possible to wire a primary and a backup circuit at the same mounting point.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e2 NM visibility with a 180° green sector for certified navigation signaling\u003c\/li\u003e\n\u003cli\u003eVertical-mount form factor with compact dimensions for tight mounting locations\u003c\/li\u003e\n\u003cli\u003e10-32 VDC input for 12 V and 24 V systems, with low draw at 1.5 W\u003c\/li\u003e\n\u003cli\u003eIP68-rated sealing for heavy spray and washdowns\u003c\/li\u003e\n\u003cli\u003eAnodized aluminum body with PMMA lens, plus potted electronics for water and vibration resistance\u003c\/li\u003e\n\u003cli\u003eSupplied pre-cabled with a 6 m lead; minimum feed wire gauge 0.5 mm² (AWG 22)\u003c\/li\u003e\n\u003cli\u003eCompliance markings for COLREG72, EN14744, IEC 60945, and USCG (UL1104)\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eVariants\u003c\/h6\u003e\u003cp\u003eThis light is offered in two finishes and two stack styles.\u003c\/p\u003e\u003cp\u003eFinish changes the exterior appearance (silver or black). Style changes whether the unit contains one light element (single stack) or two independent light elements (double stack). These part numbers are supplied pre-cabled with a 6 m lead.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e200-018G2: Finish Silver, Style Single Stack. A single 180° green light element in one housing for a straightforward one-circuit install.\u003c\/li\u003e\n\u003cli\u003e200-018G2-B: Finish Black, Style Single Stack. The same single-light format with a black anodized housing that blends into dark rails, hardtops, and window frames.\u003c\/li\u003e\n\u003cli\u003e200-018G2ST: Finish Silver, Style Double Stack. Two independent light elements in one stacked housing so you can separate primary and backup circuits without adding a second mounting location.\u003c\/li\u003e\n\u003cli\u003e200-018G2ST-B: Finish Black, Style Double Stack. The same two-light stacked format with a black housing for low-contrast installations.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eWhat’s included\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eNavigation light with pre-attached cable\u003c\/li\u003e\n\u003cli\u003eMounting hardware\u003c\/li\u003e\n\u003cli\u003eInstallation guide\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eMount the light on a flat, vertical surface where the 180° sector is not blocked by rails, canvas, or deck hardware. Plan the cable routing before drilling, and seal any penetrations to keep water out of the structure.\u003c\/p\u003e\u003cp\u003eAs with any navigation light, placement matters. Confirm the mounting location and aiming so the light’s sector is presented correctly relative to the vessel’s heading and other running lights.\u003c\/p\u003e\u003ch6\u003eElectrical and system integration\u003c\/h6\u003e\u003cp\u003eWire the unit to a switched 10-32 VDC circuit and protect it with an appropriately sized fuse or breaker for the circuit. The load is small (about 1.5 W), but keep connections clean and dry and follow normal marine wiring practices.\u003c\/p\u003e\u003cp\u003eOn double stack versions, the two light elements are independent, which supports separate switching and redundancy when your lighting plan calls for it.\u003c\/p\u003e\u003ch6\u003eWho it fits\u003c\/h6\u003e\u003cp\u003eThis is a good match for boats and yachts that need a certified 2 NM green 180° light in a compact vertical-mount package, especially when you want low current draw on 12 V or 24 V systems. The double stack style suits installations where a backup light circuit is required without adding extra fixtures on deck.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eRinse salt off the lens and housing after runs, and inspect the cable exit and mounting screws during routine checks. If the lens gets film or grime, clean it with mild soap and water to keep the sector crisp at night.\u003c\/p\u003e","brand":"Lopolight","offers":[{"title":"Silver \/ Single Stack","offer_id":52271518580917,"sku":"QBP598948-V1","price":391.51,"currency_code":"USD","in_stock":true},{"title":"Black \/ Single Stack","offer_id":52271518613685,"sku":"QBP598948-V2","price":391.51,"currency_code":"USD","in_stock":true},{"title":"Silver \/ Double Stack","offer_id":52271518646453,"sku":"QBP598948-V3","price":773.24,"currency_code":"USD","in_stock":true},{"title":"Black \/ Double Stack","offer_id":52271518679221,"sku":"QBP598948-V4","price":773.24,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1309145_qbp598948.png?v=1771555167"},{"product_id":"qbp600415","title":"Lopolight Series 301 Masthead Navigation Light, 5 NM, 225 Deg, 10-32VDC, IP68, Vertical Mount","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Lopolight 301-011 Series is a 5 NM white masthead navigation light range with a 225° arc, built for vessels in the 20-50 m (65.6-164 ft) class and intended for vertical mounting on a mast or hardtop structure. It runs on 10-32 VDC, draws 4.1 W (about 320 mA at 12 V and 170 mA at 24 V), and is sealed to IP68 for spray and washdowns.\u003c\/p\u003e\u003cp\u003eThe housing measures 74.55 x 28 x 73.16 mm (2.9 x 1.1 x 2.88 in) and uses an aluminum body with a PMMA lens. Approvals include COLREG72, EN14744, IEC 60945, IACS E10, and USCG, with additional type approvals listed by ABS, M.E.D., DNV, and LR.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e5 NM masthead light with 225° white arc for vessels 20-50 m (65.6-164 ft)\u003c\/li\u003e\n\u003cli\u003e10-32 VDC input for 12 V and 24 V DC systems\u003c\/li\u003e\n\u003cli\u003ePower draw 4.1 W (320 mA at 12 V, 170 mA at 24 V)\u003c\/li\u003e\n\u003cli\u003eIP68 sealing and operating temperature range of -25°C to 55°C\u003c\/li\u003e\n\u003cli\u003eCompact body size: 74.55 x 28 x 73.16 mm (2.9 x 1.1 x 2.88 in)\u003c\/li\u003e\n\u003cli\u003eApproved to COLREG72, EN14744, IEC 60945, IACS E10, and USCG\u003c\/li\u003e\n\u003cli\u003eFinish choices include silver anodized, black anodized, or white ceramic coated, with single stack and double stack styles\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eVariants\u003c\/h6\u003e\u003cp\u003eThis series is offered in multiple finishes and two stack styles to match both the look of your mast hardware and the way you want the light package arranged.\u003c\/p\u003e\u003cp\u003eFinish options include silver anodized, black anodized, and a white ceramic coated housing. Style is either single stack (one masthead light module, pre-cabled with a 0.75 m lead) or double stack (two stacked masthead light modules, supplied with two 0.7 m leads). Across the range, the light color remains white with a 225° arc, a 5 NM rating, a 10-32 VDC input range, and IP68 sealing.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eMount the unit on a solid vertical surface where the lens has a clear, unobstructed view forward. Check that antennas, spreaders, and radar hardware do not cut into the 225° sector once the boat is loaded and trimmed.\u003c\/p\u003e\u003cp\u003eThe factory connection lead is short, so many installs land it into a protected junction point inside the mast or under a hardtop, then continue down the boat with ship wiring. Use a fused DC circuit sized for the load and follow your vessel’s navigation-light switching arrangement.\u003c\/p\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThe 5 NM rating and 20-50 m vessel range suit larger yachts and workboats that require higher-visibility navigation lighting. The 10-32 VDC input works on both 12 V and 24 V DC systems without a separate converter, and the published minimum feed wire gauge is 0.5 mm2 (AWG 22).\u003c\/p\u003e\u003ch6\u003eMaterials and sealing\u003c\/h6\u003e\u003cp\u003eThe housing uses aluminum with an anodized finish (or a ceramic coated finish on the white option), stainless fasteners, and a PMMA lens. When mounting to stainless or carbon structures, isolate the mounting surface with an appropriate gasket or bedding to help limit galvanic corrosion, and keep the lens clean so the cut-off stays crisp.\u003c\/p\u003e\u003ch6\u003eUse cases on board\u003c\/h6\u003e\u003cp\u003eThis light suits refits where a vertical masthead fixture replaces an older incandescent unit, and new builds where you want a compact light footprint on an arch or mast. It is a good match for boats that run offshore or in busy traffic lanes where a clean 5 NM masthead light helps other vessels read your heading earlier.\u003c\/p\u003e\u003ch6\u003eWhat’s included\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eNavigation light with attached connection lead(s)\u003c\/li\u003e\n\u003cli\u003eMounting screws (M6 x 8 mm)\u003c\/li\u003e\n\u003cli\u003eInstallation guide\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Lopolight","offers":[{"title":"Silver \/ Single Stack","offer_id":52271519203509,"sku":"QBP600415-V1","price":1712.31,"currency_code":"USD","in_stock":true},{"title":"Black \/ Single Stack","offer_id":52271519236277,"sku":"QBP600415-V2","price":1712.31,"currency_code":"USD","in_stock":true},{"title":"White \/ Single Stack","offer_id":52271519269045,"sku":"QBP600415-V3","price":1841.12,"currency_code":"USD","in_stock":false},{"title":"Silver \/ Double Stack","offer_id":52271519301813,"sku":"QBP600415-V4","price":2570.86,"currency_code":"USD","in_stock":true},{"title":"Black \/ Double Stack","offer_id":52271519334581,"sku":"QBP600415-V5","price":2570.86,"currency_code":"USD","in_stock":true},{"title":"White \/ Double Stack","offer_id":52271519367349,"sku":"QBP600415-V6","price":2764.23,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1309149_qbp600415.png?v=1771555168"},{"product_id":"qbp600901","title":"Lopolight Series 301-002 LED Port Sidelight, 2 NM, Vertical Mount, 10-32V DC, IP68","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Lopolight 301-002 Series is a vertical-mount port sidelight that shows a red 112.5° sector with 2 NM visibility for vessels from 12 m to 50 m (39.4 ft to 164 ft). It runs on 10 to 32 VDC, so it fits common 12V and 24V DC systems.\u003c\/p\u003e\u003cp\u003eThe housing is sealed to IP68 and comes pre-cabled with a 2.5 m shielded marine cable for hardwiring. These lights are built for exterior mounting where spray, washdowns, and vibration are normal, such as on the cabin side, bulwark, or superstructure.\u003c\/p\u003e\u003cp\u003eThis series is a practical match for cruising boats, yachts, and commercial vessels that need a fixed port sidelight with a clean vertical mount and a finish that blends with the boat.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003ePort sidelight output: red, 112.5° sector, 2 NM visibility rating\u003c\/li\u003e\n\u003cli\u003eFor vessels 12 m to 50 m (39.4 ft to 164 ft), when installed as the port sidelight in the navigation light set\u003c\/li\u003e\n\u003cli\u003e10 to 32 VDC operating range for 12V and 24V DC systems\u003c\/li\u003e\n\u003cli\u003eIP68 sealing for exposed mounting locations and frequent washdowns\u003c\/li\u003e\n\u003cli\u003eVertical mount format with a pre-attached 2.5 m shielded cable for simple hardwiring runs\u003c\/li\u003e\n\u003cli\u003eFinish choices include silver anodized, black anodized, and white ceramic-coated housings\u003c\/li\u003e\n\u003cli\u003eApproved to COLREG72 and EN14744, and listed for U.S.C.G. requirements\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eVariants\u003c\/h6\u003e\u003cp\u003eThis series is offered with two option types: Finish (Silver, Black, White) and Style (Single Stack or Double Stack).\u003c\/p\u003e\u003cp\u003eAcross the range, the light function stays the same as a red port sidelight with 2 NM visibility, vertical mounting, 10 to 32 VDC operation, and IP68 sealing. The Finish changes the exterior appearance, and the Style changes the housing format labeled Single Stack or Double Stack.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eMount the light on the port side with the lens orientation maintained so the 112.5° sector is aimed correctly. Use a flat mounting surface and seal the fasteners as you would for any exterior penetration to keep water out of the core and structure.\u003c\/p\u003e\u003cp\u003ePlan the cable route before final mounting so the hardwired lead can be protected from chafe and kept away from hot engine-room surfaces or sharp edges.\u003c\/p\u003e\u003ch6\u003eElectrical and system integration\u003c\/h6\u003e\u003cp\u003eConnect to the vessel navigation light circuit within the 10 to 32 VDC range. The supplied shielded cable includes two conductors plus a screen, which suits clean DC installations where you want a tidy run back to the switch panel or distribution point.\u003c\/p\u003e\u003cp\u003eProtect the circuit with an appropriately sized fuse or breaker for the wiring run and follow standard marine wiring practices for connections and strain relief.\u003c\/p\u003e\u003ch6\u003eMaterials and corrosion resistance\u003c\/h6\u003e\u003cp\u003eThe housing is aluminum with either anodized or ceramic-coated finish depending on the variant, paired with a PMMA lens and stainless fasteners. IP68 sealing helps keep water out when the light lives on deck structures that see constant spray.\u003c\/p\u003e\u003ch6\u003eWhat’s included\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eNavigation light with pre-attached 2.5 m shielded cable\u003c\/li\u003e\n\u003cli\u003e2 mounting screws (M6 x 8 mm)\u003c\/li\u003e\n\u003cli\u003eInstallation guide\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Lopolight","offers":[{"title":"Silver \/ Single Stack","offer_id":52271519563957,"sku":"QBP600901-V1","price":391.51,"currency_code":"USD","in_stock":true},{"title":"Black \/ Single Stack","offer_id":52271519596725,"sku":"QBP600901-V2","price":391.51,"currency_code":"USD","in_stock":true},{"title":"White \/ Single Stack","offer_id":52271519629493,"sku":"QBP600901-V3","price":420.95,"currency_code":"USD","in_stock":false},{"title":"Silver \/ Double Stack","offer_id":52271519662261,"sku":"QBP600901-V4","price":813.93,"currency_code":"USD","in_stock":true},{"title":"Black \/ Double Stack","offer_id":52271519695029,"sku":"QBP600901-V5","price":813.93,"currency_code":"USD","in_stock":true},{"title":"White \/ Double Stack","offer_id":52271519727797,"sku":"QBP600901-V6","price":875.15,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1309156_qbp600901.png?v=1771555169"},{"product_id":"qbp601357","title":"Lopolight Series 301-109 LED Port Sidelight, 3nm, 10-32VDC, IP68, Horizontal Mount, COLREG72, USCG","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Lopolight 301-109 Series is a 3 NM red port sidelight for vessels over 50 m (164 ft) that runs on 10-32 VDC and mounts horizontally. It is built for the standard 112.5° sidelight sector, with a sealed IP68 housing for exposed locations on deck and superstructure.\u003c\/p\u003e\u003cp\u003eThe range is offered with different housing finishes and in single-stack or double-stack formats, so you can match the look of the installation and the space available at the mounting point without changing the basic function of the light.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eRed port sidelight with 3 NM visibility for vessels over 50 m (164 ft)\u003c\/li\u003e\n\u003cli\u003e112.5° sidelight sector for correct port-side navigation-light coverage\u003c\/li\u003e\n\u003cli\u003eWide 10-32 VDC input that suits both 12V and 24V onboard systems\u003c\/li\u003e\n\u003cli\u003eIP68-rated sealing for rain, spray, and routine washdowns\u003c\/li\u003e\n\u003cli\u003eHorizontal-mount housing for installations on ledges, rails, and superstructure faces where a top-mounted footprint is needed\u003c\/li\u003e\n\u003cli\u003eFinish choices across the range: silver, black, or white housing (finish varies by variant)\u003c\/li\u003e\n\u003cli\u003eSingle-stack and double-stack configurations available within the same series\u003c\/li\u003e\n\u003cli\u003eCertified to U.S.C.G., EN14744, and COLREG72\u003c\/li\u003e\n\u003cli\u003ePlug-connector style connection for a clean install and easier removal for service\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eVariants\u003c\/h6\u003e\u003cp\u003eThis series is offered in multiple configurations that vary by housing finish (silver, black, or white) and by stack style (single stack or double stack). The white version uses a ceramic-coated finish.\u003c\/p\u003e\u003cp\u003eSingle-stack and double-stack options change the physical format of the unit, while core attributes such as 3 NM range, red port sector, horizontal mounting, and 10-32 VDC operation remain consistent across the 301-109 range.\u003c\/p\u003e\u003ch6\u003eWhat’s included\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eNavigation light with plug connector\u003c\/li\u003e\n\u003cli\u003eMounting hardware\u003c\/li\u003e\n\u003cli\u003eInstallation guide\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003ePlan the mounting position so the light has a clear, uninterrupted view across its required sector, and so deck fittings, rails, and tenders do not block the beam. Keep the unit oriented correctly for the port side, and mount it on a stable, flat surface to avoid twist that can affect alignment.\u003c\/p\u003e\u003cp\u003eRoute the cable so the connector is protected from standing water and remains reachable for future service. Use proper strain relief, keep the connection points supported, and seal any fastener penetrations to prevent water tracking into the structure.\u003c\/p\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eWith a 10-32 VDC input range, the light is suitable for common 12V and 24V DC distribution on larger yachts and commercial vessels. It is specified for use on vessels over 50 m (164 ft) with a 3 NM visibility requirement, so it is a good match when you are fitting or refitting navigation lights to meet that class of vessel and route profile.\u003c\/p\u003e\u003cp\u003eAs with any navigation light, verify placement, height, and shielding with your vessel’s lighting plan so the installation meets the required visibility arcs and does not interfere with other lights on board.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eRinse salt and grime off the lens and housing as part of routine washdowns, and inspect the mounting hardware periodically for tightness. If the light is removed for service, check the connector and sealing surfaces for debris before re-installing.\u003c\/p\u003e","brand":"Lopolight","offers":[{"title":"Silver \/ Single Stack","offer_id":52271519924405,"sku":"QBP601357-V1","price":1381.37,"currency_code":"USD","in_stock":true},{"title":"Black \/ Single Stack","offer_id":52271519957173,"sku":"QBP601357-V2","price":1381.37,"currency_code":"USD","in_stock":true},{"title":"White \/ Single Stack","offer_id":52271519989941,"sku":"QBP601357-V3","price":1673.59,"currency_code":"USD","in_stock":false},{"title":"Silver \/ Double Stack","offer_id":52271520022709,"sku":"QBP601357-V4","price":2197.65,"currency_code":"USD","in_stock":true},{"title":"Black \/ Double Stack","offer_id":52271520055477,"sku":"QBP601357-V5","price":2197.65,"currency_code":"USD","in_stock":true},{"title":"White \/ Double Stack","offer_id":52271520088245,"sku":"QBP601357-V6","price":2662.54,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1309165_qbp601357.png?v=1771555170"},{"product_id":"qbp602675","title":"Lopolight Series 200-024 180 Deg White LED Navigation Light, 2NM, Vertical Mount, For Vessels Under 50m, 10-32VDC, IP68, COLREG72, USCG","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Lopolight 200-024 Series is a 2 NM, 180° white navigation light for vertical mounting on vessels up to 50 m (164 ft). It is a low-profile sector light that sits flat to a vertical surface, which helps when you are working with tight mounting space on a mast, hardtop, cabin side, or transom structure.\u003c\/p\u003e\u003cp\u003ePower is 10 to 32 VDC for both 12 V and 24 V systems. Typical current draw is 137 mA at 12 VDC and 80 mA at 24 VDC, which keeps the load modest on a nav-light circuit.\u003c\/p\u003e\u003cp\u003eThe housing is sealed to IP68 and the interior is potted to handle spray, washdowns, and vibration. Single-stack versions measure 104 x 37 x 45 mm.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e2 NM visibility with a 180° white sector\u003c\/li\u003e\n\u003cli\u003e10 to 32 VDC input for 12 V and 24 V systems\u003c\/li\u003e\n\u003cli\u003eIP68 sealing with a potted interior for wet mounting locations and vibration\u003c\/li\u003e\n\u003cli\u003eVertical mounting, with installation options from the front or from the back\u003c\/li\u003e\n\u003cli\u003eApproved to COLREG72, EN14744, IEC 60945, and USCG\u003c\/li\u003e\n\u003cli\u003eTypical current draw: 137 mA at 12 VDC and 80 mA at 24 VDC\u003c\/li\u003e\n\u003cli\u003eOperating temperature range: -25°C to 55°C\u003c\/li\u003e\n\u003cli\u003eFinish options include silver anodized aluminum, black anodized aluminum, or a white ceramic-coated finish\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eVariants\u003c\/h6\u003e\u003cp\u003eThis series is offered with two build styles and three finish options. Style choices are Single Stack and Double Stack, which changes the overall housing size at the mounting point.\u003c\/p\u003e\u003cp\u003eFinish options are Silver, Black, or White. The white finish uses a ceramic-coated housing, while the silver and black finishes use anodized aluminum. Across the range, the light output stays white with a 180° sector, 2 NM visibility, and 10 to 32 VDC input.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003ePlan the mounting location so the light has a clean line of sight across its 180° sector and is oriented correctly for the required arc. Because it is a vertical-mount light, it is commonly fitted to a flat or lightly curved surface where you can secure the body and route the cable into a dry area behind the mounting panel.\u003c\/p\u003e\u003cp\u003eWhen installing in exposed areas, pay attention to bedding and fastener sealing so water does not track into the core or wiring chase. After installation, a quick hose-down check is a practical way to confirm the mounting surface and cable entry stay dry.\u003c\/p\u003e\u003ch6\u003eElectrical and system integration\u003c\/h6\u003e\u003cp\u003eConnect the light to a 10 to 32 VDC navigation-light circuit through a properly protected switch or controller. Keep splices and terminations in a dry location when possible, and use marine-grade connectors and tinned conductors to reduce corrosion in a saltwater environment.\u003c\/p\u003e\u003ch6\u003eMaterials and corrosion resistance\u003c\/h6\u003e\u003cp\u003eThe lens is PMMA, and the fasteners are A4 stainless steel. Housing finish depends on the variant, with anodized aluminum options in silver or black and a ceramic-coated option in white. Regular freshwater rinsing after saltwater runs helps keep the finish and lens clear, especially when the light is mounted where it sees spray.\u003c\/p\u003e\u003ch6\u003eCompatibility and compliance\u003c\/h6\u003e\u003cp\u003eThis is a certified 2 NM navigation light approved to COLREG72, EN14744, IEC 60945, and USCG. Because it is a 180° white sector light, confirm that a 180° arc and white color match the specific function you are fitting on your vessel and the placement rules for your size and class.\u003c\/p\u003e\u003ch6\u003eUse on board\u003c\/h6\u003e\u003cp\u003eThis light is a good match for owners and installers who need a 180° white sector light in a compact form factor and want compatibility with either 12 V or 24 V electrical systems. It also suits mounting spots that see frequent washdowns, such as a hardtop face, mast structure, or other exposed vertical surfaces.\u003c\/p\u003e\u003ch6\u003eWhat’s included\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eNavigation light (precabled)\u003c\/li\u003e\n\u003cli\u003eInstallation guide\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Lopolight","offers":[{"title":"Silver \/ Single Stack","offer_id":52271520350389,"sku":"QBP602675-V1","price":391.51,"currency_code":"USD","in_stock":true},{"title":"Black \/ Single Stack","offer_id":52271520383157,"sku":"QBP602675-V2","price":391.51,"currency_code":"USD","in_stock":true},{"title":"White \/ Single Stack","offer_id":52271520415925,"sku":"QBP602675-V3","price":420.95,"currency_code":"USD","in_stock":false},{"title":"Silver \/ Double Stack","offer_id":52271520448693,"sku":"QBP602675-V4","price":773.24,"currency_code":"USD","in_stock":true},{"title":"Black \/ Double Stack","offer_id":52271520481461,"sku":"QBP602675-V5","price":773.24,"currency_code":"USD","in_stock":true},{"title":"White \/ Double Stack","offer_id":52271520514229,"sku":"QBP602675-V6","price":831.4,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1309171_qbp602675.png?v=1771555172"},{"product_id":"qbp604215","title":"Lopolight LED Stern Light, 2 NM, Vertical Mount, 10-32VDC, IP68","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Lopolight 301-006 Series is a 2 nautical mile, 135° white stern navigation light for vertical mounting on vessels up to 50 m (164 ft). It runs on 10-32 VDC systems and draws about 1.3 W (110 mA at 12 VDC, 50 mA at 24 VDC), so it fits cleanly into typical 12V and 24V nav-light circuits.\u003c\/p\u003e\u003cp\u003eThe housing is fully potted and rated IP68, which helps when the stern sees spray, washdowns, and vibration. Silver and black versions use anodized aluminum with a PMMA lens and stainless mounting screws, while the white version uses a ceramic-coated finish.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e135° white stern sector with 2 NM visibility for vessels up to 50 m (164 ft)\u003c\/li\u003e\n\u003cli\u003eOperating voltage 10-32 VDC for 12V and 24V DC systems\u003c\/li\u003e\n\u003cli\u003eIP68 ingress rating and fully potted electronics for water exposure and vibration\u003c\/li\u003e\n\u003cli\u003eLow current draw: 110 mA at 12 VDC, 50 mA at 24 VDC (about 1.3 W)\u003c\/li\u003e\n\u003cli\u003ePre-cabled with a 2.5 m (8.2 ft) shielded marine-grade cable; minimum feed wire gauge 0.5 mm2 (AWG 22)\u003c\/li\u003e\n\u003cli\u003eApproved to COLREG72, EN14744, IEC 60945, IACS E10, USCG, ABS, M.E.D., DNV, LR\u003c\/li\u003e\n\u003cli\u003eFinish options: silver anodized, black anodized, or white ceramic coated\u003c\/li\u003e\n\u003cli\u003eStyle options: Single Stack or Double Stack, with different overall footprints\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eVariants\u003c\/h6\u003e\u003cp\u003eThis series is offered in six configurations that combine housing finish with the Single Stack or Double Stack style.\u003c\/p\u003e\u003cp\u003eAcross the range, the light output stays white with a 135° stern sector, 2 NM visibility, vertical mounting, 10-32 VDC input, IP68 rating, and a 2.5 m cable. Single Stack versions list overall dimensions of 86.2 x 28 x 57.75 mm, while Double Stack versions list Ø92.5 mm x 96.5 mm, which matters when matching an existing mount and confirming clearance around rails, platforms, and aft hardware.\u003c\/p\u003e\u003ch6\u003eInstallation and wiring\u003c\/h6\u003e\u003cp\u003eMount the light on a truly vertical surface at the stern with a clear view across the required 135° arc. Keep it on the vessel centerline and high enough that rails, outboards, davits, or a tender on the platform do not block the beam.\u003c\/p\u003e\u003cp\u003eThe light is supplied with a 2.5 m shielded cable for a straightforward run back to the navigation light switch panel. Connect to a 10-32 VDC supply; the conductors are color-coded red for positive and black for ground, and the feed wiring is typically sized to at least 0.5 mm2 (AWG 22).\u003c\/p\u003e\u003ch6\u003eCompatibility and use on board\u003c\/h6\u003e\u003cp\u003eAs a 2 NM stern light for vessels up to 50 m, the 301-006 Series fits many coastal and offshore setups where the navigation lights are used regularly at night or in reduced visibility. It is a solid fit for sailboats, powerboats, and larger yachts that want an LED stern light that meets common navigation-light standards and keeps electrical load low on long runs.\u003c\/p\u003e\u003ch6\u003eWhat's included\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eNavigation light pre-cabled with 2.5 m (8.2 ft) shielded marine-grade cable\u003c\/li\u003e\n\u003cli\u003e2 mounting screws (M6 x 8 mm)\u003c\/li\u003e\n\u003cli\u003eInstallation guide\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Lopolight","offers":[{"title":"Silver \/ Single Stack","offer_id":52271520612533,"sku":"QBP604215-V1","price":507.88,"currency_code":"USD","in_stock":true},{"title":"Black \/ Single Stack","offer_id":52271520645301,"sku":"QBP604215-V2","price":507.88,"currency_code":"USD","in_stock":true},{"title":"White \/ Single Stack","offer_id":52271520678069,"sku":"QBP604215-V3","price":546.09,"currency_code":"USD","in_stock":false},{"title":"Silver \/ Double Stack","offer_id":52271520710837,"sku":"QBP604215-V4","price":1017.04,"currency_code":"USD","in_stock":true},{"title":"Black \/ Double Stack","offer_id":52271520743605,"sku":"QBP604215-V5","price":936.03,"currency_code":"USD","in_stock":true},{"title":"White \/ Double Stack","offer_id":52271520776373,"sku":"QBP604215-V6","price":1006.43,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1309178_qbp604215.png?v=1771555173"},{"product_id":"qbp606190","title":"Lopolight 201-014 2NM 360° Red Navigation Light, Flat Base, 10-32VDC, IP68","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Lopolight 201-014 is a 2 nautical mile, 360 degree red navigation signal light for 10 to 32 VDC systems. It is commonly used on vessels up to 50 m (164 ft) where an all-round red light is part of the required COLREG light display.\u003c\/p\u003e\u003cp\u003eThis light mounts horizontally on an FB flat base and comes pre-cabled with a 0.75 m shielded marine-grade cable, so wiring runs are straightforward on a mast, hardtop, or radar arch. Single stack versions measure Ø92.5 mm x 36 mm, while double stack versions are Ø92.5 mm x 58 mm.\u003c\/p\u003e\u003cp\u003eThe housing is anodized aluminum with a PMMA lens and sealing rated to IP68 for exposed locations that see spray and washdowns. Power draw is low at about 2.1 W, with typical current around 150 mA at 12 VDC or 85 mA at 24 VDC.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e2 NM visibility with a 360 degree red signal\u003c\/li\u003e\n\u003cli\u003e10 to 32 VDC input for 12V and 24V electrical systems\u003c\/li\u003e\n\u003cli\u003eLow power draw (about 2.1 W), typically 150 mA at 12 VDC or 85 mA at 24 VDC\u003c\/li\u003e\n\u003cli\u003eIP68 sealing for wet, exposed mounting locations\u003c\/li\u003e\n\u003cli\u003eFB flat base with a POM mounting system for horizontal installations\u003c\/li\u003e\n\u003cli\u003ePre-cabled with a 0.75 m shielded marine-grade cable\u003c\/li\u003e\n\u003cli\u003eApproved to COLREG72 and EN14744, with additional approvals including IEC 60945 and IACS E10, and USCG recognition\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eVariants\u003c\/h6\u003e\u003cp\u003eThis product is offered in multiple configurations to match different mounting layouts and finish preferences.\u003c\/p\u003e\u003cp\u003eFinish varies between silver and black, and style varies between single stack and double stack. The stack style refers to the light module arrangement in the housing.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e201-014-FB: Finish Silver; Style Single Stack. Single stack provides one all-round red light for installations that call for a single red signal light.\u003c\/li\u003e\n\u003cli\u003e201-014-FB-B: Finish Black; Style Single Stack. Black finish suits dark masts, hardtops, and other low-glare installations.\u003c\/li\u003e\n\u003cli\u003e201-014ST-FB: Finish Silver; Style Double Stack. Double stack provides two all-round red lights in one vertical assembly when the light plan calls for a pair of red signals.\u003c\/li\u003e\n\u003cli\u003e201-014ST-FB-B: Finish Black; Style Double Stack. The double stack format keeps two red signals aligned while maintaining a black finish for darker mounting surfaces.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eWhat’s included\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eNavigation light (pre-cabled with a 0.75 m shielded marine-grade cable)\u003c\/li\u003e\n\u003cli\u003eInstallation guide\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003ePlan the mounting point so the light has a clear 360 degree view with minimal shadowing from antennas, flags, backstays, or other deck hardware. Keep the light level so the beam pattern is not tilted, and route the cable with chafe protection and a drip loop before it enters the structure.\u003c\/p\u003e\u003cp\u003eOn board, this is a good match for cruising yachts and working boats that need an all-round red signal light in an exposed location and want low electrical draw without adding extra cabling or external junction boxes.\u003c\/p\u003e","brand":"Lopolight","offers":[{"title":"Silver \/ Single Stack","offer_id":52271520809141,"sku":"QBP606190-V1","price":679.33,"currency_code":"USD","in_stock":true},{"title":"Black \/ Single Stack","offer_id":52271520841909,"sku":"QBP606190-V2","price":679.33,"currency_code":"USD","in_stock":true},{"title":"Silver \/ Double Stack","offer_id":52271520874677,"sku":"QBP606190-V3","price":1193.41,"currency_code":"USD","in_stock":false},{"title":"Black \/ Double Stack","offer_id":52271520907445,"sku":"QBP606190-V4","price":1193.41,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1309187_qbp606190.png?v=1771555174"},{"product_id":"qbp606376","title":"Lopolight 201-003 2 NM Combined Port\/Starboard Sidelight, Red\/Green, 10-32VDC, IP68","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Lopolight 201-003 Series is a combined red and green sidelight with a 2 nautical mile range for vessels up to 20 m (65.6 ft). It runs on 10 to 32 VDC, so it fits 12 V and 24 V systems, and it mounts horizontally as a single fixture instead of separate port and starboard lights.\u003c\/p\u003e\u003cp\u003eIt is sealed to IP68 and built around a silver anodized aluminum housing with a PMMA lens. The body is about 92.5 mm in diameter and 36 mm high, and it is supplied with a 2.5 m shielded cable for routing to a nav light switch or lighting panel.\u003c\/p\u003e\u003cp\u003eWhen installed, it needs a clear sightline and correct orientation so red shows to port and green shows to starboard, with each sector covering 112.5 degrees. The series includes a standard orientation and an upside-down orientation for installations where the light must be mounted inverted while keeping the light sectors correct.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eCombined red\/green sidelight in one fixture (112.5 degrees per color sector)\u003c\/li\u003e\n\u003cli\u003e2 nautical mile rated visibility for vessels up to 20 m (65.6 ft)\u003c\/li\u003e\n\u003cli\u003e10 to 32 VDC input for 12 V and 24 V electrical systems\u003c\/li\u003e\n\u003cli\u003eIP68 sealing for rain, spray, and washdowns\u003c\/li\u003e\n\u003cli\u003eSilver anodized aluminum housing with PMMA lens and A4 stainless steel screws\u003c\/li\u003e\n\u003cli\u003e2.5 m shielded cable for clean routing through the bow, pulpit, or deck structure\u003c\/li\u003e\n\u003cli\u003eApproved to COLREG72, EN14744, IEC 60945, IACS E10, and recognized by USCG (with additional approvals depending on installation requirements)\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eVariants\u003c\/h6\u003e\u003cp\u003eThis product is offered in multiple configurations with the same basic function: a combined red\/green sidelight for horizontal mounting.\u003c\/p\u003e\u003cp\u003eThe difference between the options listed here is the mounting orientation (standard vs upside-down). Other installation details should be matched to the specific part number.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e201-003 (Style: Standard). A standard orientation that suits typical horizontal mounting locations where the light sits upright.\u003c\/li\u003e\n\u003cli\u003e201-003-FB-REVERSE (Style: Upside-Down). An inverted orientation for horizontal mounts where the fixture must be installed upside-down while keeping the port and starboard sectors correct.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eMount the light on a horizontal surface where it cannot be blocked by pulpits, anchor rollers, rails, or deck gear. Alignment matters: the fixture must be oriented so the correct color shows to the correct side of the vessel, and it should face the intended direction of travel.\u003c\/p\u003e\u003cp\u003ePlan your cable run before drilling. Route the 2.5 m lead to a protected interior space, use a drip loop where it passes through the deck, and seal any fastener holes and cable pass-throughs to keep water out of the core.\u003c\/p\u003e\u003ch6\u003eElectrical and system integration\u003c\/h6\u003e\u003cp\u003eThis light is made for DC systems from 10 to 32 volts. Wire it on a properly fused navigation light circuit and size wiring for the length of the run; 0.5 mm2 (AWG 22) is a minimum feed wire gauge, and longer runs often benefit from heavier cable to reduce voltage drop.\u003c\/p\u003e\u003cp\u003ePower draw is 2.2 W, with current consumption around 163 mA at 12 VDC and 90 mA at 24 VDC, which keeps load low on typical nav lighting circuits.\u003c\/p\u003e\u003ch6\u003eMaterials and environmental protection\u003c\/h6\u003e\u003cp\u003eThe anodized aluminum body and IP68 sealing suit open-deck mounting where salt spray and washdowns are normal. Rinse salt off periodically, keep the lens clean, and avoid abrasive cleaners that can haze the PMMA lens over time.\u003c\/p\u003e\u003ch6\u003eUse on board\u003c\/h6\u003e\u003cp\u003eA combined sidelight is a practical choice when you want one fixture on the bow rather than separate port and starboard units, while still meeting the required red and green sectors. It suits sailboats and powerboats up to 20 m where a horizontal mounting location is available and the light can remain unobstructed.\u003c\/p\u003e","brand":"Lopolight","offers":[{"title":"Standard","offer_id":52271521005749,"sku":"QBP606376-V1","price":528.48,"currency_code":"USD","in_stock":false},{"title":"Upside-Down","offer_id":52271521038517,"sku":"QBP606376-V2","price":650.52,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1309192_qbp606376.png?v=1771555175"},{"product_id":"qbp606583","title":"Lopolight Series 201-011 LED Masthead Light, Vertical Mount, 225 Deg White Beam, 3NM, 10-32V DC, IP68","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Lopolight 201-011 Series is a 3 NM masthead (steaming) navigation light that shows a 225° white sector for vessels 12 to 20 m (39.4 to 65.6 ft) and mounts on vertical surfaces.\u003c\/p\u003e\u003cp\u003eIt runs on 10 to 32 VDC (works on 12V and 24V systems), is IP68 rated for exposed mounting, and comes precabled with a 0.75 m shielded lead to simplify wiring runs inside a mast, hardtop, or radar arch.\u003c\/p\u003e\u003cp\u003eApprovals include COLREG72, EN14744, USCG, IEC 60945, and IACS E10, which helps when you are matching a replacement light to an existing compliance setup.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e3 NM visibility with a 225° white masthead sector for boats 12 to 20 m (39.4 to 65.6 ft)\u003c\/li\u003e\n\u003cli\u003eVertical-mount format for common masthead and superstructure placements\u003c\/li\u003e\n\u003cli\u003eWide input range (10 to 32 VDC) for 12V and 24V DC systems\u003c\/li\u003e\n\u003cli\u003eIP68 sealing for rain, spray, and washdowns when installed with proper bedding and cable routing\u003c\/li\u003e\n\u003cli\u003eHousing finish options: Silver anodized, Black anodized, or White ceramic coated\u003c\/li\u003e\n\u003cli\u003eAluminum housing with PMMA lens and stainless mounting screws specified for the installation\u003c\/li\u003e\n\u003cli\u003eSingle Stack and Double Stack styles to match different masthead-light arrangements in one mounting location\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eVariants\u003c\/h6\u003e\u003cp\u003eThe 201-011 Series is offered in two styles: Single Stack and Double Stack. Both are vertical-mount masthead lights with a 225° white sector and a 3 NM rating.\u003c\/p\u003e\u003cp\u003eFinish varies across the range (Silver, Black, or White) to match mast hardware and topside color schemes. Electrical input and sealing are consistent across the series, so selection is mainly about exterior finish and whether you need a single or double light stack at the mounting point.\u003c\/p\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis is a masthead (steaming) light, so placement matters. Mount it high and centered where the 225° sector can project forward without being blocked by sails, antennas, biminis, or radar gear.\u003c\/p\u003e\u003cp\u003eBefore ordering, confirm your vessel length and required light configuration under the rules you operate to, and verify that a 225° masthead sector is the correct function for that position on your boat.\u003c\/p\u003e\u003ch6\u003eInstallation and wiring\u003c\/h6\u003e\u003cp\u003eMount the fixture plumb on the vertical surface and align it so the lens faces forward. Route the cable down with a drip loop before it enters the mast or cabin to reduce water migration along the wire.\u003c\/p\u003e\u003cp\u003eConnect to a switched DC circuit within the 10 to 32 VDC range. Use tinned marine-grade conductors and sealed terminations, and protect the circuit with a correctly sized fuse or breaker for your wiring plan and standards.\u003c\/p\u003e\u003ch6\u003eMaterials and corrosion resistance\u003c\/h6\u003e\u003cp\u003eThe housing is aluminum with the exterior finish depending on the variant, and the light is sealed to an IP68 level. For saltwater boats, avoid trapping water behind the fixture, bed fasteners as you would with other deck hardware, and keep dissimilar metals isolated where needed.\u003c\/p\u003e\u003ch6\u003eUse cases on board\u003c\/h6\u003e\u003cp\u003eThis series suits sailboats and powerboats in the 12 to 20 m range that need a vertical-mount masthead light for night running, channel transits, and low-visibility operation. The Double Stack variants integrate two light modules in one housing for installations that call for a stacked masthead-light arrangement.\u003c\/p\u003e\u003ch6\u003eWhat’s included\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eNavigation light\u003c\/li\u003e\n\u003cli\u003e0.75 m shielded cable (pre-cabled)\u003c\/li\u003e\n\u003cli\u003eMounting screws (M6 x 8 mm)\u003c\/li\u003e\n\u003cli\u003eInstallation guide\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Lopolight","offers":[{"title":"Silver \/ Single Stack","offer_id":52271521169589,"sku":"QBP606583-V1","price":854.63,"currency_code":"USD","in_stock":true},{"title":"Black \/ Single Stack","offer_id":52271521202357,"sku":"QBP606583-V2","price":854.63,"currency_code":"USD","in_stock":true},{"title":"White \/ Single Stack","offer_id":52271521235125,"sku":"QBP606583-V3","price":918.95,"currency_code":"USD","in_stock":false},{"title":"Silver \/ Double Stack","offer_id":52271521267893,"sku":"QBP606583-V4","price":1281.96,"currency_code":"USD","in_stock":true},{"title":"Black \/ Double Stack","offer_id":52271521300661,"sku":"QBP606583-V5","price":1281.96,"currency_code":"USD","in_stock":true},{"title":"White \/ Double Stack","offer_id":52271521333429,"sku":"QBP606583-V6","price":1378.43,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1309195_qbp606583.png?v=1771555176"},{"product_id":"qbp608393","title":"Lopolight Series 200-016 G2 180 Deg Red LED Navigation Light, For Vessels to 50m, 2NM, Vertical Mount, 10-32V DC, IP68","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Lopolight 200-016 Series is a vertical-mount red navigation light with a 2 NM rating, built to run on 10 to 32 VDC. It covers a 180 degree sector and is rated for vessels up to 50 m (164 ft).\u003c\/p\u003e\u003cp\u003eThe housing is anodized aluminum and the light is sealed to an IP68 rating, which suits exposed installations where spray, washdowns, and vibration are part of normal use on board.\u003c\/p\u003e\u003cp\u003eThis series is commonly used where a wider red sector is required, and it is a straightforward fit for boats running 12V or 24V DC lighting circuits.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e2 NM visibility with a 180 degree red sector\u003c\/li\u003e\n\u003cli\u003e10 to 32 VDC input for 12V and 24V electrical systems\u003c\/li\u003e\n\u003cli\u003eIP68 sealing for wet mounting locations and washdowns\u003c\/li\u003e\n\u003cli\u003eAnodized aluminum housing with a vertical-mount form factor\u003c\/li\u003e\n\u003cli\u003eSingle Stack and Double Stack styles, with Double Stack using two light sources\u003c\/li\u003e\n\u003cli\u003eFinish options across the range: Silver, Black, or White\u003c\/li\u003e\n\u003cli\u003e0.7 m cable lead for wiring into an existing navigation light circuit\u003c\/li\u003e\n\u003cli\u003eApproved to COLREG72 and EN14744, and USCG certified\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eVariants\u003c\/h6\u003e\u003cp\u003eThis series is offered with different housing finishes (Silver, Black, or White) and in Single Stack or Double Stack styles.\u003c\/p\u003e\u003cp\u003eAcross the range, the core format remains the same: a 2 NM red light with a 180 degree sector that runs on 10 to 32 VDC and mounts vertically. The main difference is the stack style, which changes whether the assembly uses one light source or two.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eMounting is intended on a vertical surface where the light has a clear line of sight through its required sector. On most boats this means a mast or superstructure face, a pilothouse side, or another solid vertical panel that keeps the beam unobstructed by rails, antennas, or canvas.\u003c\/p\u003e\u003cp\u003ePlan cable routing so the lead can reach a protected junction point, then seal any deck or bulkhead penetrations as you would for other exterior lighting. Final alignment matters on navigation lights, so take the time to confirm the light is square to the vessel centerline and level before tightening fasteners.\u003c\/p\u003e\u003ch6\u003eElectrical and system integration\u003c\/h6\u003e\u003cp\u003eThe 10 to 32 VDC input suits common marine DC systems without needing a converter. Wire it into a switched navigation light circuit using proper circuit protection and marine-grade connections that stay secure in vibration.\u003c\/p\u003e\u003ch6\u003eUse on board\u003c\/h6\u003e\u003cp\u003eThis is a good match for yachts and working boats up to 50 m that need a compliant 2 NM red light in a vertical-mount package. It also fits well for refits where you want to keep the same mounting location while updating to a sealed LED unit.\u003c\/p\u003e\u003ch6\u003eWhat's included\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eNavigation light with pre-attached 0.7 m cable\u003c\/li\u003e\n\u003cli\u003eMounting hardware\u003c\/li\u003e\n\u003cli\u003eInstallation guide\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Lopolight","offers":[{"title":"Silver \/ Single Stack","offer_id":52271521398965,"sku":"QBP608393-V1","price":391.51,"currency_code":"USD","in_stock":true},{"title":"Black \/ Single Stack","offer_id":52271521431733,"sku":"QBP608393-V2","price":391.51,"currency_code":"USD","in_stock":true},{"title":"White \/ Single Stack","offer_id":52271521464501,"sku":"QBP608393-V3","price":420.95,"currency_code":"USD","in_stock":false},{"title":"Silver \/ Double Stack","offer_id":52271521497269,"sku":"QBP608393-V4","price":773.24,"currency_code":"USD","in_stock":true},{"title":"Black \/ Double Stack","offer_id":52271521530037,"sku":"QBP608393-V5","price":773.24,"currency_code":"USD","in_stock":true},{"title":"White \/ Double Stack","offer_id":52271521562805,"sku":"QBP608393-V6","price":831.4,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1309202_qbp608393.png?v=1771555178"}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/collections\/1266115_lopolight.webp?v=1768106212","url":"https:\/\/www.qualityboatparts.com\/collections\/lopolight.oembed?page=2","provider":"Quality Boat Parts","version":"1.0","type":"link"}