{"title":"Hella Marine","description":"","products":[{"product_id":"qbp838291","title":"Hella Marine NaviLED TRIO Tri-Color\/Anchor Nav Light, 2NM Rated, 9-33V, IP67","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Hella Marine 980650001 is a 2 NM masthead tri-colour navigation lamp with a separate all-round white anchor mode for sailing vessels under sail. It runs on Multivolt 9-33 V DC, so it fits both 12 V and 24 V onboard systems without any voltage converter.\u003c\/p\u003e\u003cp\u003ePower draw stays low for overnight running: the port, starboard, and stern sectors are under 3.5 W combined, and the anchor light is under 1.5 W. The lamp is IP67 (completely sealed) and built with a nylon housing that resists UV exposure and impact, plus a Grilamid lens that holds up in salt air and vibration.\u003c\/p\u003e\u003cp\u003eIt mounts on a 316 stainless steel shaft and comes pre-wired with 400 mm of three-core tinned marine cable. Electrical protection is built in for real-world DC systems, with spike protection to +500 V and reverse polarity protection to -700 V. Approvals include BSH, IMO COLREG 72, USCG, ABYC A-16, Maritime NZ, CE, and UKCA.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e2 NM-rated tri-colour sectors with a separate 360 degree all-round white anchor function\u003c\/li\u003e\n\u003cli\u003eMultivolt 9-33 V DC input for 12 V and 24 V systems\u003c\/li\u003e\n\u003cli\u003eLow consumption: port\/starboard\/stern under 3.5 W combined; anchor under 1.5 W\u003c\/li\u003e\n\u003cli\u003eIP67 protection with a fully sealed construction for washdowns, spray, and salt contamination\u003c\/li\u003e\n\u003cli\u003e316 stainless mounting shaft for a secure masthead installation\u003c\/li\u003e\n\u003cli\u003ePre-wired with 400 mm three-core tinned marine cable for a clean mast run\u003c\/li\u003e\n\u003cli\u003eProtection against common DC faults: spike protected to +500 V and reverse polarity to -700 V\u003c\/li\u003e\n\u003cli\u003eMounting footprint 85 mm with an overall height of 95 mm for clearance checks at the masthead\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis is a mast-top navigation light intended for a horizontal mounting surface at or near the top of the mast. Tri-colour navigation lights are used on sailing vessels under sail and are not displayed when the vessel is operating as a power-driven vessel. As with any navigation light change, confirm the correct configuration for your vessel length and local requirements before installation.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eThe base uses a simple three-hole pattern (3 x 5 mm holes on a 50.8 mm pitch circle), which makes it easy to mark and drill accurately. Orientation matters on tri-colour lights, so plan your cable exit and base alignment so the stern sector faces aft once the light engine is fitted.\u003c\/p\u003e\u003cp\u003eThe lamp installs over the mounting shaft and locks into place for a secure fit, while still allowing removal for service access at the masthead. Keep the cable protected as it exits the mast to avoid chafe, and bed the base appropriately for a watertight install on deck hardware and mast caps.\u003c\/p\u003e\u003ch6\u003eElectrical and system integration\u003c\/h6\u003e\u003cp\u003eWiring is straightforward for most sailboats: a common negative (black) and separate positives for the tri-colour function (red) and the anchor function (blue), which pairs well with a dedicated navigation switch or separate switch positions. Use DC power only and protect the circuit with a fuse rated at 3 A maximum.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eRinse with fresh water after heavy salt exposure and check the cable entry and mounting hardware during routine mast inspections. If you unstep the mast seasonally, it is a good time to inspect the connector and the cable for any signs of chafe or corrosion at the masthead.\u003c\/p\u003e","brand":"Hella Marine","offers":[{"title":"Default Title","offer_id":52268859490485,"sku":"QBP838291","price":560.59,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1297869_qbp838291.jpg?v=1771540479"},{"product_id":"qbp199134","title":"Hella Marine Series 2984 Tri-Color Masthead Navigation Light, 2 NM, 12V\/25W Bulb, IP55, Black Housing","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Hella Marine 002984535 is a mast-mounted tri-colour navigation light for sailboats, combining port (red), starboard (green), and stern (white) sectors in one housing. It runs on a 12 V DC system, is rated to 2 nautical miles, and uses an incandescent BAY15d 12 V \/ 25 W bulb.\u003c\/p\u003e\u003cp\u003eThe black housing and lens are made from UV-resistant plastic that holds up to knocks and typical mast vibration. The enclosure is non-magnetic and carries an IP55 protection rating for rain, spray, and routine washdowns.\u003c\/p\u003e\u003cp\u003eThis style of light is commonly fitted on yachts up to 20 m when sailing under sail, mounted high to help keep the sectors clear of sails and rigging. It meets key navigation-light compliance requirements including IMO COLREG 72, USCG, ABYC A-16, BSH, and Maritime NZ approvals.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eTri-colour output (red, green, white) with a 2 NM visibility rating\u003c\/li\u003e\n\u003cli\u003e12 V incandescent system with BAY15d 12 V \/ 25 W bulb included\u003c\/li\u003e\n\u003cli\u003eIP55-rated housing for spray, rain, and normal deck washdowns\u003c\/li\u003e\n\u003cli\u003eUV-resistant, impact-resistant plastic housing and lens; non-magnetic and saltwater resistant\u003c\/li\u003e\n\u003cli\u003eBayonet-lock access for straightforward bulb changes\u003c\/li\u003e\n\u003cli\u003eCompact footprint around 107 mm tall by 88 mm wide for tight masthead placements\u003c\/li\u003e\n\u003cli\u003eCable entry through the base plate via a rubber grommet\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eWhat's included\u003c\/h6\u003e\u003cul\u003e\u003cli\u003eIncandescent bulb: BAY15d, 12 V \/ 25 W\u003c\/li\u003e\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis light is intended for 12 V DC electrical systems and mast-mounted tri-colour use on sailing yachts. Check the available mounting area and clearances against the housing size (about 107 x 88 mm), and confirm the light will have a clear view with minimal shadowing from antennas, wind instruments, and standing rigging.\u003c\/p\u003e\u003cp\u003eIf you are replacing an older tri-colour fixture, verify your existing wiring condition inside the mast and plan for proper marine-grade terminations since this style is not pre-wired.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eMount the light so the red and green sectors face port and starboard, with the white sector facing aft, and position it where the lens has an uninterrupted view of the horizon. On most sailboats this is at the masthead; if any rigging or hardware creates shadows, adjust placement so the sectors stay clean.\u003c\/p\u003e\u003cp\u003eRoute wiring through the base entry and keep sealing tight around the rubber grommet. A drip loop before the cable entry helps prevent water tracking down the cable into the mast.\u003c\/p\u003e\u003ch6\u003eElectrical and system integration\u003c\/h6\u003e\u003cp\u003eBecause this is an incandescent fixture, treat it like a continuous load when sizing wiring and protection for long mast runs. A dedicated switch and correctly sized fuse at the distribution panel keeps the circuit easy to manage.\u003c\/p\u003e\u003cp\u003eWhen wiring multiple navigation-light configurations on the same boat, make sure your switching arrangement prevents running conflicting light sets at the same time.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eRinse salt off the lens and housing during normal washdowns and inspect the cable entry and mounting fasteners after heavy weather. Keeping connections clean and sealed helps avoid intermittent lighting faults at the mast.\u003c\/p\u003e\u003cp\u003eThe bayonet-lock design makes bulb swaps quick. Carrying a spare BAY15d 12 V \/ 25 W bulb on board is a practical backup for night runs.\u003c\/p\u003e","brand":"Hella Marine","offers":[{"title":"Default Title","offer_id":52268894716085,"sku":"QBP199134","price":119.95,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1298147_qbp199134.jpg?v=1771540689"},{"product_id":"qbp785184","title":"Hella Marine Tri-Color\/Anchor Navigation Light, 2NM, 12V, Incandescent, Black Housing, IP55","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Hella Marine 002984601 is a masthead combination navigation lamp that gives you a tri-color sailing light (red, green, and white sectors) plus a 360 degree all-round white anchor light in one unit. It is a 12 V fixture with 2 nautical miles visibility, and it measures about 200 mm tall by 88 mm wide for a clean masthead install.\u003c\/p\u003e\u003cp\u003eThis is an incandescent light that uses a BAY15d base bulb (25 W). The black housing and lens are plastic that stands up to sun exposure and the bumps that happen during rig work, and the light is non-magnetic for use near the compass.\u003c\/p\u003e\u003cp\u003eWith an IP55 rating, it suits typical topside conditions like rain, spray, and routine washdowns, as long as the wiring and seals are kept tidy during installation and service.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eTwo light functions in one masthead fixture: tri-color navigation light and 360 degree all-round white anchor light\u003c\/li\u003e\n\u003cli\u003e2 NM visibility rating with 12 V DC operation\u003c\/li\u003e\n\u003cli\u003eUses an incandescent BAY15d bulb (25 W)\u003c\/li\u003e\n\u003cli\u003eIP55 protection rating for weather exposure and spray\u003c\/li\u003e\n\u003cli\u003eNon-magnetic construction for use on sailboats where compass interference matters\u003c\/li\u003e\n\u003cli\u003eUV-resistant plastic housing and lens that handle sun exposure and everyday impacts\u003c\/li\u003e\n\u003cli\u003eHorizontal surface mount with cable entry through the base using a rubber grommet\u003c\/li\u003e\n\u003cli\u003eBayonet-lock access for straightforward bulb replacement\u003c\/li\u003e\n\u003cli\u003eMeets IMO COLREG 72, BSH, USCG, ABYC A-16, CE, RINA, and Maritime NZ requirements\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eWhat’s included\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eTri-color\/all-round navigation lamp assembly\u003c\/li\u003e\n\u003cli\u003e12 V \/ 25 W BAY15d bulb\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis style of combined masthead light is commonly used on sailing yachts up to 20 m (65.6 ft) where a single tri-color lantern at the top of the mast is permitted under the navigation rules. If your boat is set up for separate bow and stern lights, confirm your required light arrangement before switching to a masthead tri-color.\u003c\/p\u003e\u003cp\u003eBecause it is a 12 V fixture, it is a match for standard 12 V house systems. For 24 V boats, this specific 12 V configuration is not the right fit unless your masthead light circuit is stepped down to 12 V.\u003c\/p\u003e\u003ch6\u003eInstallation and wiring\u003c\/h6\u003e\u003cp\u003eMount it on a level, horizontal surface at the masthead so the light sectors stay aligned correctly. The cable feeds through the base plate, and the rubber grommet helps protect the wiring as it passes through the mast cap.\u003c\/p\u003e\u003cp\u003ePlan the wiring so your switch panel can select the tri-color sailing light or the all-round white anchor light as separate functions. Use tinned marine wire and make splices where they are protected, since mast wiring sees constant vibration and moisture over time.\u003c\/p\u003e\u003ch6\u003eMaintenance and bulb replacement\u003c\/h6\u003e\u003cp\u003eThe bayonet-lock housing makes servicing straightforward when it is time to replace the bulb. When you open the fixture, keep the sealing surfaces clean and re-seat everything carefully before closing it back up, and wipe salt film off the lens so the light stays crisp at night.\u003c\/p\u003e\u003ch6\u003eUse on board\u003c\/h6\u003e\u003cp\u003eThis is a practical choice for sailboats that do night passages and also anchor out, where you want one masthead fixture to cover both under-sail navigation lighting and an all-round white anchor light. It also works well as a like-for-like replacement when you already have a masthead mount and 12 V wiring set up for this type of combined light.\u003c\/p\u003e","brand":"Hella Marine","offers":[{"title":"Default Title","offer_id":52268894912693,"sku":"QBP785184","price":183.6,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1298148_qbp785184.jpg?v=1771540691"},{"product_id":"qbp290429","title":"Hella Marine 3562 Series Stern Navigation Light, 2 NM, 12V, Incandescent, Black Housing, IP54, Surface Mount","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Hella Marine 003562015 is a 2 NM stern navigation lamp with an incandescent 12V\/10W SV8.5 bulb in a black housing for vertical surface mounting.\u003c\/p\u003e\u003cp\u003eIt suits yachts and powerboats that use a traditional bulb-based stern light and want something straightforward to service. The snap-lock housing opens for a bulb change without tools, which is handy when you need to swap a lamp at the dock or during a quick turnaround.\u003c\/p\u003e\u003cp\u003eThe housing and lens are UV and impact resistant plastic, with an IP54 rating for dust and splashing water. Overall size is 75 mm high, 63 mm wide, and 53 mm deep, so it fits well on tighter transoms and stern structures.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e2 NM stern light output for navigation use on 12V DC systems\u003c\/li\u003e\n\u003cli\u003eIncandescent lamp with a 12V\/10W SV8.5 bulb included\u003c\/li\u003e\n\u003cli\u003eSnap-lock housing for tool-free access when replacing the bulb\u003c\/li\u003e\n\u003cli\u003eIP54-rated enclosure for spray and splashing water exposure\u003c\/li\u003e\n\u003cli\u003eUV and impact resistant plastic housing and lens, with a non-magnetic, saltwater resistant build\u003c\/li\u003e\n\u003cli\u003eCable entry through the base plate with a rubber grommet to protect wiring at the mount\u003c\/li\u003e\n\u003cli\u003eApprovals: IMO COLREG 72, RINA, USCG, ABYC A-16, Maritime NZ\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eWhat’s included\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eStern navigation lamp assembly\u003c\/li\u003e\n\u003cli\u003e12V\/10W SV8.5 bulb\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eThis lamp is meant for vertical surface mounting at the stern. Pick a spot where the lens can be seen clearly from astern without being blocked by an outboard, swim ladder, davits, or rail gear.\u003c\/p\u003e\u003cp\u003eRoute the supply wires through the base plate and seat the rubber grommet cleanly so the cable is supported where it enters the housing. Use tinned marine wire and heat-shrink terminations, and seal any fastener holes as needed for your mounting surface.\u003c\/p\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis is a 12V incandescent stern lamp and is typically used on vessels up to 12 m where a 2 NM stern light is required. If you are replacing an older 3562-series stern light, the form factor and bulb style make it a common like-for-like swap.\u003c\/p\u003e\u003cp\u003eIt is a good match for boat owners who want a compact stern light with a simple service routine and a familiar bulb you can keep as a spare on board.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eRinse salt off the lens and housing as part of normal washdowns and check that the base grommet stays seated. If the light output drops or fails, open the snap-lock housing, replace the SV8.5 bulb, and confirm the seal is sitting properly before heading out.\u003c\/p\u003e","brand":"Hella Marine","offers":[{"title":"Default Title","offer_id":52268897665205,"sku":"QBP290429","price":34.27,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1298267_qbp290429.jpg?v=1771540702"},{"product_id":"qbp227958","title":"Hella Marine Battery Master Switch Spare Key, For 150A Switch 2843, Key Removable in OFF Position","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Hella Marine 706729011 is a spare key for the Hella Marine 150A Battery Master Switch (2843 series), so you can still shut down or restore DC battery power if the original key goes missing.\u003c\/p\u003e\u003cp\u003eIt fits the keyed switch used to isolate your boat’s electrical system, and the key can be removed when the switch is in the OFF position so current is fully interrupted.\u003c\/p\u003e\u003cp\u003eKeeping an extra key onboard is a simple way to avoid a no-start situation at the dock, and it also helps when you routinely remove the key to leave the battery switch OFF while the boat is unattended.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eReplacement key for Hella Marine Battery Master Switch series 2843 (150A keyed switch)\u003c\/li\u003e\n\u003cli\u003eKey-removable OFF position so the switch can stay fully disconnected without a key left in place\u003c\/li\u003e\n\u003cli\u003eRestores normal battery switch control if the primary key is lost or damaged\u003c\/li\u003e\n\u003cli\u003eNo electrical work required since this is a mechanical key for the switch actuator\u003c\/li\u003e\n\u003cli\u003eEasy to store as a labeled spare in your onboard electrical spares kit\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis key is intended for the Hella Marine 150A Battery Master Switch in the 2843 series. Confirm your switch is the keyed version before ordering, since non-keyed battery switches use different knobs and hardware.\u003c\/p\u003e\u003ch6\u003eInstallation and operation\u003c\/h6\u003e\u003cp\u003eThere is no wiring or setup. Insert the key into the battery master switch and turn the switch ON or OFF as needed. When the switch is OFF, the key can be removed to leave the circuit disconnected.\u003c\/p\u003e\u003cp\u003eAs with any battery isolation switch, shut down high-draw DC loads and chargers before switching OFF to reduce arcing at the contacts and avoid nuisance resets onboard.\u003c\/p\u003e\u003ch6\u003eUse on board\u003c\/h6\u003e\u003cp\u003eThis spare key is a good match for boats that use a keyed battery master switch as a regular shutdown point, especially when the switch is mounted in an engine room, cockpit locker, or battery compartment where keys can get misplaced.\u003c\/p\u003e","brand":"Hella Marine","offers":[{"title":"Default Title","offer_id":52268898189493,"sku":"QBP227958","price":9.79,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1298268_qbp227958.jpg?v=1771540704"},{"product_id":"qbp880740","title":"Hella Marine Twin Beam Hand Held Search Light, 12V, 55W\/100W, IPX6K, Black Housing","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Hella Marine 998502001 is a hand-held twin-beam halogen search light for 12V boats, with a black housing for use on deck, in the cockpit, or at the helm when you need a controllable spot of light.\u003c\/p\u003e\u003cp\u003eTwo separate switches run two reflectors and two H3 bulbs: a 55W beam for close-range work around docks and lines, and a 100W beam for longer-range spotting. Power is supplied through a spiral cable with a cigarette-lighter plug and up to 3.5 m of extended length, which helps when you are moving between stations.\u003c\/p\u003e\u003cp\u003eThe housing is shock- and vibration-resistant plastic with a high-gloss aluminum reflector, and the lens sits behind an extended front edge that helps protect the glass. An IP X6K protection rating makes it a better fit for wet conditions than typical handheld lights.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e12V hand-held search light with two independently switched halogen beams\u003c\/li\u003e\n\u003cli\u003e55W close-range H3 bulb and 100W long-range H3 bulb\u003c\/li\u003e\n\u003cli\u003eTwo reflectors and two bulbs on separate switches for quick beam changes\u003c\/li\u003e\n\u003cli\u003eTrigger switch in the grip for momentary control and Morse code signaling\u003c\/li\u003e\n\u003cli\u003eSpiral power cable with cigarette-lighter plug; extended length 3.5 m\u003c\/li\u003e\n\u003cli\u003eShock- and vibration-resistant plastic housing with high-gloss aluminum reflector\u003c\/li\u003e\n\u003cli\u003eExtended front edge that helps protect the glass lens\u003c\/li\u003e\n\u003cli\u003eIP X6K protection rating for exposure to spray and washdowns\u003c\/li\u003e\n\u003cli\u003eMaximum power draw up to 155W on 12V (both beams on)\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and onboard use\u003c\/h6\u003e\u003cp\u003eThis light is operated by hand, which is useful when you need to sweep a shoreline, pick out channel markers, check the dock, or locate gear without changing your fixed lighting. The coiled lead helps keep slack down, but it should still be routed so it cannot snag on throttles, winches, cleats, or rod holders.\u003c\/p\u003e\u003cp\u003eA deck mount base accessory is available separately (8HG 998 519-001) for setups that want a consistent stowage or mounting point.\u003c\/p\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eUse on 12V DC systems with an accessory socket that matches the cigarette-lighter plug. This version is a good match for boaters who want a handheld spotlight that plugs into existing 12V power without adding dedicated wiring.\u003c\/p\u003e\u003ch6\u003eWhat’s included\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eHand-held search light with spiral power cable and cigarette-lighter plug\u003c\/li\u003e\n\u003cli\u003e12V 55W H3 bulb\u003c\/li\u003e\n\u003cli\u003e12V 100W H3 bulb\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eRinse salt residue off the housing and lens after heavy spray or washdowns, and let the unit dry before stowing. Avoid touching halogen bulbs with bare fingers during replacement, and keep the lens free of grit so it does not scratch when wiped.\u003c\/p\u003e","brand":"Hella Marine","offers":[{"title":"Default Title","offer_id":52268899336373,"sku":"QBP880740","price":264.38,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1298271_qbp880740.jpg?v=1771540706"},{"product_id":"qbp001692","title":"Hella Marine Deck Mount Base, For Twin Beam Handheld Searchlight, Black","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Hella Marine 8HG998519001 is a deck mount base for the Twin Beam handheld searchlight, giving you a fixed place to stow the light on board instead of letting it roll around in a locker.\u003c\/p\u003e\u003cp\u003eIt is finished in black and suits mounting spots such as the cockpit, near the helm, or inside a locker with quick access. The Twin Beam handheld searchlight uses a spiral cable that extends to 3.5 m, so place the mount where the lead can reach your power connection without being stretched across walkways.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eDeck mount base accessory for the Hella Marine Twin Beam handheld searchlight\u003c\/li\u003e\n\u003cli\u003eBlack finish that blends into most helm and cockpit hardware\u003c\/li\u003e\n\u003cli\u003eGives the light a consistent stowage point so it stays easy to find and grab at night\u003c\/li\u003e\n\u003cli\u003ePassive accessory that does not change wiring or system voltage on board\u003c\/li\u003e\n\u003cli\u003eHelps keep the searchlight from sliding around when the boat is moving\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis mount is meant for the Hella Marine Twin Beam handheld searchlight. It is not a universal deck mount, so it is worth matching it to your specific Twin Beam light before ordering.\u003c\/p\u003e\u003cp\u003eIf you are running the Twin Beam in either a 12V or 24V setup, the mount remains the same since it is purely mechanical.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003ePick a flat surface where the light can be lifted out with one hand and where the lens will not be knocked by hatches, lines, or rods. Many crews place it near the helm, under a hardtop, or just inside a companionway for quick access.\u003c\/p\u003e\u003cp\u003eUse marine fasteners suited to your mounting surface, and seal any penetrations to keep water out of the core. After the first few outings, re-check fastener tightness once the bedding compound has settled.\u003c\/p\u003e\u003ch6\u003eElectrical and system integration\u003c\/h6\u003e\u003cp\u003eThe deck mount does not connect electrically. Plan cable routing and strain relief for the handheld searchlight itself, especially if the spiral lead will be stretched to its full 3.5 m reach.\u003c\/p\u003e\u003cp\u003eKeep the plug and outlet positioned so they stay dry and out of standing water, and avoid routing the lead where it can be stepped on or pinched by hatches.\u003c\/p\u003e\u003ch6\u003eUse cases on board\u003c\/h6\u003e\u003cp\u003eUseful for boats that keep a handheld searchlight ready for night docking, spotting channel marks, checking the anchor set, or scanning the water during an emergency. Having a dedicated deck mount keeps the light in the same place every time, which matters when you are moving fast in the dark.\u003c\/p\u003e\u003cp\u003eA good match for skippers who want the Twin Beam searchlight accessible from the helm or cockpit without dedicating a full locker just for storage.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eRinse salt spray off with fresh water during routine washdowns and check that the mount is still tight to the deck. If the mount is installed in a high-traffic area, inspect it more often for loosening or impact damage.\u003c\/p\u003e","brand":"Hella Marine","offers":[{"title":"Default Title","offer_id":52268899369141,"sku":"QBP001692","price":22.0,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1298275_qbp001692.jpg?v=1771540708"},{"product_id":"qbp467304","title":"Hella Marine Module 6213 Flush Mount Spreader Light, 12V, Double Beam, Halogen, H3 Bulb","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Hella Marine 358115091 is a halogen spreader light that mounts flush and throws a double-beam pattern for deck work on 12V boats. It is the Module 6213 close-range (CR) style, which concentrates light where you are handling lines, rigging, or gear instead of pushing a long spot far off the bow.\u003c\/p\u003e\u003cp\u003eThe rectangular face sits clean in a hardtop, radar arch, or transom panel, giving you strong cockpit and deck illumination without a protruding bracket. It is a practical choice for docking, loading, setting up tackle, and general night work when you want a bright halogen beam and a low-profile install.\u003c\/p\u003e\u003cp\u003ePlan your mounting space before cutting: the overall size is approximately 7 x 3.75 x 3.5 in, and you will need room behind the panel for the housing and wiring.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eFlush mount form factor for a clean install on hardtops, arches, and other flat panels.\u003c\/li\u003e\n\u003cli\u003eDouble-beam close-range (CR) output suited to cockpit, deck, and dockside tasks.\u003c\/li\u003e\n\u003cli\u003e12 V H3 halogen configuration for straightforward integration on common 12V DC systems.\u003c\/li\u003e\n\u003cli\u003eReflector aiming adjustment of about 7 degrees to fine-tune where the light lands.\u003c\/li\u003e\n\u003cli\u003eApproximate overall size of 7 x 3.75 x 3.5 in to help confirm fit and back-side clearance.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eFlush mounting typically involves cutting a rectangular opening, bedding the face so water cannot wick into the core, and fastening the unit securely to handle vibration underway. Use a marine sealant suited to your surface and take time to seal any exposed laminate or core material around the cutout.\u003c\/p\u003e\u003cp\u003eRoute wiring where it stays protected from chafe and heat, and leave enough service slack so the light can be pulled forward for access during maintenance.\u003c\/p\u003e\u003ch6\u003eElectrical and system integration\u003c\/h6\u003e\u003cp\u003eHalogen spreader lights draw more current than comparable LED fixtures, so cable sizing and voltage drop matter. Use tinned marine wire sized for the run length and load, and protect the circuit with appropriate switching and overcurrent protection for your installation. On longer runs, a relay placed closer to the light can help maintain brightness.\u003c\/p\u003e\u003ch6\u003eUse cases on board\u003c\/h6\u003e\u003cp\u003eMount it under the aft edge of a hardtop to light the cockpit, under an arch for stern deck coverage, or forward-facing on the cabin top as a docking aid. The close-range pattern works well for tying up, cleaning fish boxes, sorting gear, and moving around the boat after dark.\u003c\/p\u003e\u003cp\u003eThis light is a good match for boaters who want a flush look and prefer a serviceable halogen setup for occasional night work or docking.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eRinse salt spray from the lens and bezel after trips and inspect bedding and fasteners periodically. If light output drops, check connections for corrosion and replace the H3 halogen lamp as needed.\u003c\/p\u003e","brand":"Hella Marine","offers":[{"title":"Default Title","offer_id":52268899664053,"sku":"QBP467304","price":72.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1298276_qbp467304.jpg?v=1771540709"},{"product_id":"qbp281368","title":"Hella Marine HD Double Mount Stainless Steel Feet, For Sea Hawk-350\/470 LED Light Bars, Pair","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Hella Marine 958128811 is a stainless steel double-mount bracket set that stacks two Sea Hawk LED Light Bars on the same mounting position. It fits the Sea Hawk-470 and Sea Hawk-350 light bars and keeps each bar on its own adjustable angle, so you can aim them independently.\u003c\/p\u003e\u003cp\u003eThis is a mounting accessory only, meant for installs where you want more light coverage but do not have room for separate mounting points. A common setup is running one bar as a driving pattern and the other as a work pattern, then setting the angles so you light up the water ahead and the deck area without washing out the helm.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eBuilt for stacking two Sea Hawk-470 or Sea Hawk-350 LED Light Bars in a single location\u003c\/li\u003e\n\u003cli\u003eStainless steel mounting feet suited to open-air marine mounting areas\u003c\/li\u003e\n\u003cli\u003eEach light bar can be adjusted separately after mounting for precise beam aim\u003c\/li\u003e\n\u003cli\u003eSupports mixed beam layouts such as driving plus work patterns on one bracket set\u003c\/li\u003e\n\u003cli\u003eUseful when mounting space is limited on a hardtop, T-top, radar arch, mast spreader, or cabin brow\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis bracket set is intended for Sea Hawk-470 and Sea Hawk-350 LED Light Bars. Confirm you have the matching Sea Hawk light bar style and enough clearance above and below the mounting point for a stacked pair, including room for tilt adjustment and cable routing.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003ePlan the stack so the lower bar and upper bar can still be tilted without contacting the mounting surface or each other. Leave a small service loop in the wiring at the light bar ends so you can fine-tune aim later, and re-check fasteners after the first few runs since vibration can settle a new install.\u003c\/p\u003e\u003ch6\u003eUse cases on board\u003c\/h6\u003e\u003cp\u003eThis setup is a good match for boats that want forward lighting and working light from the same area, such as docking and deck handling on coastal cruisers, cockpit and bow illumination on fishing boats, or additional coverage on a tender where mounting locations are limited.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eRinse the hardware with fresh water after saltwater use and check the mount periodically for loosened fasteners. Keeping the stack tight and aligned helps the lights hold their aim and reduces wear at the adjustment points.\u003c\/p\u003e\u003ch6\u003eWhat’s included\u003c\/h6\u003e\u003cul\u003e\u003cli\u003eStainless steel mounting feet (one pair)\u003c\/li\u003e\u003c\/ul\u003e","brand":"Hella Marine","offers":[{"title":"Default Title","offer_id":52268923846837,"sku":"QBP281368","price":39.17,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1298277_qbp281368.jpg?v=1771540846"},{"product_id":"qbp634044","title":"Hella Marine Sea Hawk-XL Dual Color LED Deck Floodlight, White\/Warm White, 9-33V DC, IP67, 2.5m Cable, Black Housing","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Hella Marine 980950081 is a deck and spreader LED floodlight with two light colors: a 5000K white work light and a 2700K warm white mode, in a black housing. It runs on 9 to 33V DC (12V and 24V systems) and throws a spread beam around 76 degrees for lighting up a cockpit, aft deck, dock, or work area.\u003c\/p\u003e\u003cp\u003eIn white mode it produces 750 lumens, which is the one you will reach for when you are docking, rigging lines, or working gear at night. Warm white is softer on the eyes for evenings on board, with 300 lumens at 2700K, so you can keep the area lit without the harsher look of cool white.\u003c\/p\u003e\u003cp\u003eThe unit is sealed to IP67 for exposed mounting and comes pre-wired with 2.5 m of three-core tinned marine cable, so installation is straightforward when you plan your cable run back to the switch panel.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eMultivolt input: 9 to 33V DC for 12V and 24V electrical systems\u003c\/li\u003e\n\u003cli\u003eDual-colour output: 5000K white (750 lm) plus 2700K warm white (300 lm)\u003c\/li\u003e\n\u003cli\u003ePower draw: 12W in white mode; 6W in warm white mode\u003c\/li\u003e\n\u003cli\u003eIP67 sealing for wet, exposed mounting locations\u003c\/li\u003e\n\u003cli\u003ePre-wired with 2.5 m three-core tinned marine cable for clean installations\u003c\/li\u003e\n\u003cli\u003eGrilamid lens that resists impact and UV exposure\u003c\/li\u003e\n\u003cli\u003eThermally conductive, corrosion-proof polymer housing with a 316 stainless steel mounting bracket\u003c\/li\u003e\n\u003cli\u003eApprovals: CE, RCM, UKCA\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and wiring\u003c\/h6\u003e\u003cp\u003eThis is a bracket-mount floodlight, so you can aim it where you need it and then set the swivel resistance once mounted. On a boat, it helps to mount it high enough to clear rails and gear, and to aim it down and out so it lights the deck without shining straight into the helm or cockpit seating.\u003c\/p\u003e\u003cp\u003eThe three-core cable supports switching between the two colours using a standard ON\/OFF\/ON style switch setup at the panel. Protect the circuit with a fuse rated at 5A maximum, and keep polarity correct since the LED modules will not light if wired backwards.\u003c\/p\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eUse this light on DC systems only. With a 9 to 33V DC operating range, it fits most 12V and 24V boats without needing external drivers or resistors. The included 2.5 m cable covers many nearby switch or junction locations, but longer runs should be extended using tinned marine wire and sealed connections.\u003c\/p\u003e\u003cp\u003eIf you are matching lighting across the boat, note that the white mode is 5000K (a neutral, work-focused white) and the warm white mode is 2700K for a softer look that blends better with many cabin and cockpit ambient lights.\u003c\/p\u003e\u003ch6\u003eMaterials and sealing\u003c\/h6\u003e\u003cp\u003eThe housing is non-metallic and thermally conductive, which helps with heat management while avoiding the corrosion issues that can show up around metal housings in saltwater environments. The Grilamid lens holds up well to sun exposure and knocks from gear, and the 316 stainless bracket suits exposed mounting on hardtops, arches, cockpit coamings, and work decks.\u003c\/p\u003e\u003ch6\u003eUse on board\u003c\/h6\u003e\u003cp\u003eThis light is a good match for boats that want one deck light that can flip between a bright, neutral work light and a warmer mode for evenings at anchor or at the dock. It fits well on sportfishing boats, commercial vessels, and performance sailboats where you need dependable deck lighting that stays consistent across 12V and 24V systems.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eRinse the light with fresh water after saltwater runs, especially around the bracket and fasteners, and wipe the lens with a soft cloth to keep output clean. Avoid abrasive pads and harsh solvents on the lens and housing so the surface stays clear and easy to maintain over time.\u003c\/p\u003e","brand":"Hella Marine","offers":[{"title":"Default Title","offer_id":52268923912373,"sku":"QBP634044","price":281.52,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1298259_qbp634044.jpg?v=1771540848"},{"product_id":"qbp575210","title":"Hella Marine DuraLED 12 Interior\/Exterior LED Lamp, 3000K Warm White Light, White Housing, 12\/24V DC, IP67, ISO 8846 Ignition Protected, Surface Mount","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Hella Marine 959700701 is a surface-mount interior\/exterior utility lamp that puts out warm white light (3000K) on 12\/24V DC systems while drawing under 2.5W. It has a compact footprint at 140 x 65 x 32 mm (5.5 x 2.56 x 1.25 in), making it easy to place on bulkheads, in lockers, or under side decks without eating up space.\u003c\/p\u003e\u003cp\u003eThis version is w\/out switch, so it is meant to be controlled from your existing lighting circuit or a separate switch. The housing is IP67 completely sealed for wet locations, and it is ISO 8846 ignition protected for use in areas where flammable vapors may be present. Power comes in through a 500 mm pre-wired twin-core marine cable.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eWarm white 3000K output that reads comfortably for interior spaces while still working as a practical utility light\u003c\/li\u003e\n\u003cli\u003eMultivolt 12\/24V DC operation with low draw: \u0026lt; 2.5W (\u0026lt; 0.20A @ 12V \/ \u0026lt; 0.10A @ 24V)\u003c\/li\u003e\n\u003cli\u003eIP67 completely sealed for damp compartments, washdowns, and exterior mounting locations\u003c\/li\u003e\n\u003cli\u003eISO 8846 ignition protection for installation in higher-risk onboard areas where vapors can be present\u003c\/li\u003e\n\u003cli\u003eSurface-mount size: 140 x 65 x 32 mm (5.5 x 2.56 x 1.25 in); weight 115 g including cable\u003c\/li\u003e\n\u003cli\u003ePre-wired with 500 mm of twin-core marine cable for straightforward hook-up\u003c\/li\u003e\n\u003cli\u003eUV-resistant, enhanced impact acrylic lens with a heavy-duty nylon shroud and white housing\u003c\/li\u003e\n\u003cli\u003eLow EMC noise to help avoid interference with onboard radio communications\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eMount the lamp on a clean, flat surface where the wide beam can spill into the area you are trying to light. The fastening load is taken up by the bush mount, which helps reduce stress on the lamp housing when it is tightened down on a bulkhead or overhead panel.\u003c\/p\u003e\u003cp\u003ePlan your cable run before fastening the unit in place. The lamp is pre-wired with 500 mm of twin-core cable, so most installs will involve extending the leads with tinned marine wire and sealed connectors. Keep splices out of direct bilge water, leave a small drip loop when mounting under a deck, and protect the circuit with appropriate overcurrent protection as part of your vessel wiring.\u003c\/p\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis lamp runs on both 12V and 24V DC systems and does not have an integrated switch. If you are replacing an older cabin or locker light that had a built-in switch, plan for external switching at the panel, at a bulkhead switch, or via an existing circuit.\u003c\/p\u003e\u003cp\u003eUse the overall dimensions (140 x 65 x 32 mm) to confirm clearance where the lamp will sit and where the cable will route behind the mounting surface. The warm white 3000K tone is a good match when you want utility lighting that feels softer in cabins, passageways, and storage spaces.\u003c\/p\u003e\u003ch6\u003eUse cases on board\u003c\/h6\u003e\u003cp\u003eThis style of lamp is commonly used for engine rooms, lazarettes, storage lockers, cockpit lockers, and under-deck compartments where you want broad light coverage without needing a recessed fixture. It also works well as a general interior utility light in cabins or under gunwales on fishing boats where wiring access is limited.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eThe sealed construction keeps routine maintenance simple. Rinse salt residue as needed and wipe the lens with mild soap and water to keep the acrylic clear. Periodically check the cable support and any extension splices to make sure they stay dry, supported, and corrosion-free.\u003c\/p\u003e","brand":"Hella Marine","offers":[{"title":"Default Title","offer_id":52268924043445,"sku":"QBP575210","price":110.16,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1298260_qbp575210.jpg?v=1771540850"},{"product_id":"qbp130698","title":"Hella Marine 3562 Masthead Navigation Light, 2 NM, 12V, IP54, Vertical Surface Mount, Black Housing","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Hella Marine 003562005 is a 12V incandescent masthead navigation lamp with 2 nautical mile visibility and a black housing. It uses a 12V \/ 10W SV8.5 bulb (included) and carries an IP54 rating for protection against dust and splashing water. Housing and lens are UV and impact-resistant plastic, which helps it handle sun exposure and the bumps that happen around rigging and hardware.\u003c\/p\u003e\u003cp\u003eThe snap-lock housing opens without tools, which keeps bulb changes straightforward when you are troubleshooting at the dock or swapping a spare before a night run. The lens is white, and the unit is non-magnetic, which is helpful when mounted near sensitive instruments.\u003c\/p\u003e\u003cp\u003eApprovals include IMO Col Reg 72, RINA, USCG, ABYC A-16, and Maritime NZ.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e2 nautical mile visibility rating for masthead navigation lighting\u003c\/li\u003e\n\u003cli\u003e12V DC incandescent setup with 12V \/ 10W SV8.5 bulb included\u003c\/li\u003e\n\u003cli\u003eUV and impact-resistant plastic housing and lens in a black finish\u003c\/li\u003e\n\u003cli\u003eIP54 protection against dust and splashing water\u003c\/li\u003e\n\u003cli\u003eSnap-lock housing for tool-free bulb replacement\u003c\/li\u003e\n\u003cli\u003eVertical surface mount with cable entry through the base plate using a rubber grommet\u003c\/li\u003e\n\u003cli\u003eNon-magnetic construction and approvals to IMO Col Reg 72, RINA, USCG, ABYC A-16, and Maritime NZ\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eWhat’s included\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eMasthead navigation lamp\u003c\/li\u003e\n\u003cli\u003e12V \/ 10W SV8.5 incandescent bulb\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and wiring\u003c\/h6\u003e\u003cp\u003eThis light mounts to a vertical surface. Plan the install so the cable can pass through the base plate cleanly, and make sure the rubber grommet seats fully to reduce water entry at the cable point. Use tinned marine wire and protected connections, especially when the run is exposed to spray and vibration.\u003c\/p\u003e\u003cp\u003eIt is intended for 12V DC systems. On 24V boats, a suitable DC-DC converter or a 24V-rated navigation light is typically required.\u003c\/p\u003e\u003ch6\u003eUse on board\u003c\/h6\u003e\u003cp\u003eThis is a practical match for boats that are keeping an incandescent navigation light setup for simple spares and straightforward troubleshooting. It also fits well on refits where you are replacing a tired masthead light and want the same mounting style and service approach used across the Hella Marine 3562 series.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eRinse salt film off the lens and housing with fresh water, and avoid abrasive cleaners that can haze plastics over time. Periodically check the grommet and cable entry for a tight fit, and confirm the snap-lock closes fully after a bulb change.\u003c\/p\u003e","brand":"Hella Marine","offers":[{"title":"Default Title","offer_id":52268924076213,"sku":"QBP130698","price":34.27,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1298266_qbp130698.jpg?v=1771540852"},{"product_id":"qbp457630","title":"Hella Marine ValueFit Design LED Light Bar, 11 in, Combo Beam, 10-30V, 60W, 3000 lm","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Hella Marine 357209001 is a ValueFit Design Series 6-LED light bar with a combo beam for deck, spreader, and general work lighting on boats. It runs on 10-30 V DC (12 V and 24 V systems) and draws 60 W.\u003c\/p\u003e\u003cp\u003eLight output is rated at 3,000 lm, and the housing carries an IP67 rating for spray and washdowns when installed with proper sealing and wiring protection. The bar measures 289 x 65 x 90 mm (11.37 x 2.56 x 3.54 in) and uses a die-cast aluminum housing with a clear polycarbonate lens.\u003c\/p\u003e\u003cp\u003eThis size and beam style make sense when you want one fixture that can light up a working area close to the boat while still throwing useful light forward for docking, line handling, and after-dark tasks.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e6 high-power LEDs with a combo beam pattern (wide spread with added reach)\u003c\/li\u003e\n\u003cli\u003e10-30 V DC input for common 12 V and 24 V electrical systems\u003c\/li\u003e\n\u003cli\u003e60 W draw, roughly 5 A at 12 V and 2.5 A at 24 V for circuit planning\u003c\/li\u003e\n\u003cli\u003eIP67-rated enclosure for wet environments and regular washdowns\u003c\/li\u003e\n\u003cli\u003eDie-cast aluminum housing with a clear polycarbonate lens\u003c\/li\u003e\n\u003cli\u003eOverall size: 289 x 65 x 90 mm (11.37 x 2.56 x 3.54 in)\u003c\/li\u003e\n\u003cli\u003eStainless steel mounting fasteners help reduce corrosion issues in saltwater use\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eMount it where the beam can do its job without shining directly into the cockpit or reflecting off shiny hardware. On a hardtop, radar arch, or mast spreader, aim the bar slightly down so light lands on the deck and transom area instead of the horizon.\u003c\/p\u003e\u003cp\u003eUse a backing plate or substantial washers on thin panels, and bed any fastener penetrations so water stays out of the core. If mounting to aluminum structures, take basic anti-galvanic precautions at the hardware and contact points.\u003c\/p\u003e\u003ch6\u003eElectrical and system integration\u003c\/h6\u003e\u003cp\u003eThis is a straightforward DC light with wire leads, so it ties into your existing switched circuit rather than a marine network. Plan a clean run back to a protected distribution point, and use tinned marine wire with heat-shrink terminations to keep corrosion out of the connections.\u003c\/p\u003e\u003cp\u003eBecause it is a 60 W load, pay attention to voltage drop on longer runs to towers, arches, and spreaders. Keeping the wiring sized for the run and the environment helps the light stay bright at the fixture when the alternator is not running.\u003c\/p\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThe 289 mm overall length suits smaller boats where a long bar would look out of place or be hard to mount. It is also a practical option on sailboats where a compact spreader light can be positioned to light the foredeck without adding much windage.\u003c\/p\u003e\u003cp\u003eThis is auxiliary lighting meant for working areas and visibility around the boat. It is not a navigation light and should not be used in place of required running lights.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eRinse with fresh water after salt exposure and check mounting hardware periodically for tightness, especially if the boat sees pounding or vibration. Clean the polycarbonate lens with mild soap and water and avoid harsh solvents that can haze plastic over time.\u003c\/p\u003e","brand":"Hella Marine","offers":[{"title":"Default Title","offer_id":52269003473077,"sku":"QBP457630","price":266.83,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1298338_qbp457630.jpg?v=1771541420"},{"product_id":"qbp457872","title":"Hella Marine Twin Beam Fixed-Mount Search Light, Thru-Cabin Roof Mount, 12V, 110W, IPX6K, Halogen","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Hella Marine 998502021 is a fixed mount twin beam search light that installs through a cabin roof for deck use on 12V boats. It uses two halogen beams on separate switches and can be aimed with 360° rotation and 30° vertical adjustment, so you can work the light around the bow, dock, or channel markers without moving the unit itself.\u003c\/p\u003e\u003cp\u003eWith both beams on, plan for a 110W load (2 x 55W). Overall height is 488 mm and the base diameter is 154 mm, which helps when you are checking clearance above the headliner and choosing a spot that will not interfere with hatches, handrails, or a radar arch.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eThrough-cabin roof mounting for a stable deck installation\u003c\/li\u003e\n\u003cli\u003e360° rotation with 30° up\/down adjustment for aiming where you need it\u003c\/li\u003e\n\u003cli\u003eTwin reflectors with two halogen bulbs on separate switches for close range and long range use\u003c\/li\u003e\n\u003cli\u003e12V DC version with 2 x 55W H3 bulbs (110W total when both beams are on)\u003c\/li\u003e\n\u003cli\u003eExtended front edge that helps protect the glass lens from knocks on deck\u003c\/li\u003e\n\u003cli\u003eOverall height 488 mm with a 154 mm base diameter for layout planning\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eThis style of search light mounts through the cabin roof, with the light head and base outside and the control hardware accessible from inside the cabin or wheelhouse. When you choose the location, leave room for the head to rotate and tilt, and make sure the inside run clears liners, grab rails, and overhead wiring.\u003c\/p\u003e\u003cp\u003eBecause it sits in an exposed area, bed the mounting base properly and route the wiring with a drip loop so water does not track into the cabin.\u003c\/p\u003e\u003ch6\u003eElectrical and system integration\u003c\/h6\u003e\u003cp\u003eUse it on a 12V DC system and size the switch, wiring, and circuit protection for the full 110W draw when both beams are running. If your boat is 24V, this 12V version is not a direct match.\u003c\/p\u003e\u003ch6\u003eUse cases on board\u003c\/h6\u003e\u003cp\u003eThis light is a good fit for skippers who dock in unlit marinas, pick up moorings after dark, or want a dedicated deck search light that can be aimed quickly from inside. It is also useful on fishing boats for spotting buoys and gear at night without leaving the helm.\u003c\/p\u003e\u003ch6\u003eMaintenance and spares\u003c\/h6\u003e\u003cp\u003eKeep spare H3 halogen bulbs on board and avoid touching the glass when replacing them. After heavy spray or washdowns, a quick rinse and a visual check of the lens area helps keep the light working as expected.\u003c\/p\u003e","brand":"Hella Marine","offers":[{"title":"Default Title","offer_id":52269004193973,"sku":"QBP457872","price":318.24,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1298342_qbp457872.jpg?v=1771541421"},{"product_id":"qbp513750","title":"Hella Marine Mini ISO Relay, SPST, 12V, 50A, Mounting Bracket","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Hella Marine 007793041 is a 12V Mini ISO power relay with a single normally open circuit (SPST, Form A) rated for 50A continuous on the N\/O contact at 85°C.\u003c\/p\u003e\u003cp\u003eIt is a practical way to run higher-current gear from a low-current switch or control output. The coil uses resistor suppression (680 ohm), which helps reduce coil kickback without forcing a polarity on the coil connections.\u003c\/p\u003e\u003cp\u003eThe relay has an IP54-rated housing, a black body, and an integrated mounting bracket, so it can be secured in a protected electrical area that sees vibration and occasional splash, but not direct washdown or standing water.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eNominal 12V coil with up to 18V max coil voltage; pick-up at 8.0V or less and drop-out at 1.3V or more\u003c\/li\u003e\n\u003cli\u003eCoil resistance 100 ohm (plus or minus 10%), with resistor suppression for non-polarized coil wiring\u003c\/li\u003e\n\u003cli\u003e50A continuous switching capacity on the normally open contact, with inrush capability up to 200A (lamp) or 150A (motor)\u003c\/li\u003e\n\u003cli\u003eFast response with operating and releasing times up to 10 ms\u003c\/li\u003e\n\u003cli\u003e4-pin Mini ISO layout with standard relay terminal numbering (85\/86 coil, 30 feed, 87 switched output)\u003c\/li\u003e\n\u003cli\u003eBlade terminals sized 6.3 x 0.8 mm (85\/86) and 9.5 x 1.2 mm (30\/87), plus bracket mounting for a secure installation\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eElectrical and system integration\u003c\/h6\u003e\u003cp\u003eTerminal 30 is the high-current feed, terminal 87 is the switched output, and terminals 85 and 86 power the coil. Because the load tabs are larger (9.5 x 1.2 mm), confirm your relay socket or crimp terminals are the correct size and rated for the current you are running.\u003c\/p\u003e\u003cp\u003eOn a 12V boat, this relay is commonly used to let a dash switch, breaker panel switch, or electronic controller trigger a larger load such as deck and spreader lights, a horn, pumps, or other accessories. Protect the feed to terminal 30 with the right fuse or breaker for the wire and the load, and keep the high-current run short to reduce voltage drop.\u003c\/p\u003e\u003ch6\u003eInstallation and placement on board\u003c\/h6\u003e\u003cp\u003eUse the mounting bracket to fasten the relay to a bulkhead, under-helm electrical panel, or inside an enclosure where it stays accessible for inspection. IP54 handles splash and dust, but it should still be kept out of bilges and away from areas that stay wet or get hit with a hose.\u003c\/p\u003e\u003cp\u003eIf the circuit has a heavy startup surge, confirm the load is within the relay’s inrush limits and that your wiring and connections stay cool under load.\u003c\/p\u003e\u003ch6\u003eWho it fits\u003c\/h6\u003e\u003cp\u003eThis relay is a solid match for 12V systems that need straightforward on\/off control of a single higher-current circuit from a small control signal, especially when you want a bracket-mounted Mini ISO relay rather than a loose plug-in cube.\u003c\/p\u003e","brand":"Hella Marine","offers":[{"title":"Default Title","offer_id":52269009273013,"sku":"QBP513750","price":14.69,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1298668_qbp513750.jpg?v=1771541444"},{"product_id":"qbp513795","title":"Hella Marine SPST Mini ISO Relay, 12V, 50\/70A, Resistor Coil Suppression, Dust Cover","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Hella Marine 007793031 is a 12 V, 4-pin Mini ISO power relay with a normally open (SPST\/Form A) contact and built-in resistor coil suppression. It is rated at 50 A and carries an IP54 protection rating, making it a practical choice for switching higher-current DC loads from a low-current helm switch, keypad, or control module.\u003c\/p\u003e\u003cp\u003eOn a boat, this type of relay is commonly used to keep current out of the dash and shorten the high-amp wire run by placing the relay closer to the load or the distribution point. The resistor coil suppression helps tame switching spikes, which is useful when the relay is triggered by electronics or long control-wire runs.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e12 V coil for 12 V DC marine electrical systems\u003c\/li\u003e\n\u003cli\u003eSPST\/Form A normally open contact for straightforward on\/off control\u003c\/li\u003e\n\u003cli\u003e50 A current rating for many accessory and utility circuits\u003c\/li\u003e\n\u003cli\u003eMini ISO footprint with 4 blade terminals for common relay sockets and fuse\/relay panels\u003c\/li\u003e\n\u003cli\u003eResistor coil suppression to reduce voltage spikes when the coil is switched off\u003c\/li\u003e\n\u003cli\u003eIP54 protection rating with a dust cover, suited to protected mounting locations\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and wiring\u003c\/h6\u003e\u003cp\u003ePlan the install so the relay sits in a relay box, electrical locker, or other protected area, not in a bilge space or anywhere it can be soaked. Use a proper relay socket or holder so the terminals are supported and the relay cannot work loose from vibration.\u003c\/p\u003e\u003cp\u003eSize the fuse or breaker and wire gauge for the load you are switching, not for the control circuit. Keep the high-current feed protected close to the power source, and secure wiring runs so they do not chafe. Before crimping, confirm the terminal markings on the relay body and match them to your wiring diagram.\u003c\/p\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis relay uses the Mini ISO 4-pin blade layout found in many relay\/fuse panels and marine distribution builds that borrow standard automotive-style relays. It is intended for 12 V control voltage, so it is not a drop-in choice for a 24 V coil circuit.\u003c\/p\u003e\u003ch6\u003eOn-board use cases\u003c\/h6\u003e\u003cp\u003eThis relay is a good match for switching loads such as deck and spreader lights, horns, small pumps, fans, or an accessory bus feed, where you want the helm control to carry only a small trigger current. It also fits well in refits where a standard 4-pin Mini ISO relay socket is already in place and you need resistor-suppressed coil switching.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eIn saltwater environments, protect terminals from corrosion with a sealed relay box where possible, clean crimps, and heat-shrink insulation. Periodically check for warmth at the socket and for discoloration at the terminals, both of which can point to a loose connection or an undersized wire run.\u003c\/p\u003e","brand":"Hella Marine","offers":[{"title":"Default Title","offer_id":52269009502389,"sku":"QBP513795","price":14.69,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1298669_qbp513795.jpg?v=1771541445"},{"product_id":"qbp513817","title":"Hella Marine Mini ISO Relay, 12V, 5-Pin, SPDT, 20\/40A, Diode Coil Suppression, IP54","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Hella Marine 007794041 is a 12V mini ISO relay with a 5-pin SPDT (Form C) contact set, rated for 40A continuous on the normally-open contact and 20A on the normally-closed contact (at 85°C). It carries an IP54 rating and uses diode coil suppression to reduce electrical noise back into the control circuit.\u003c\/p\u003e\u003cp\u003eOn a boat, this relay is a clean way to switch higher-current loads using a lower-current helm switch, keypad output, or automation trigger, without running heavy cable up to the console. It is sized for typical relay blocks and sockets and is well suited to protected electrical spaces where vibration and occasional splash are part of normal life onboard.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e12V nominal coil with pull-in at = 8.0V and drop-out at = 1.0V\u003c\/li\u003e\n\u003cli\u003eSPDT \/ Form C changeover contacts (terminals 30, 87, 87A) with coil terminals 85 and 86\u003c\/li\u003e\n\u003cli\u003eRated continuous load at 85°C: 40A (N\/O) and 20A (N\/C)\u003c\/li\u003e\n\u003cli\u003eInrush capability noted for demanding starts: up to 150A (lamp) and 166A (motor)\u003c\/li\u003e\n\u003cli\u003eSuppression diode across the coil to tame switching spikes on the control side\u003c\/li\u003e\n\u003cli\u003eIP54 rating with dust cover for use in protected compartments\u003c\/li\u003e\n\u003cli\u003eISO 8092 6.3 x 0.8 mm blade terminals with tin-plated contacts and AgSnO2 contact material\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis is a standard mini ISO, 5-terminal relay with 6.3 x 0.8 mm blades, making it compatible with many common relay sockets, relay blocks, and harness pigtails used in marine and vehicle electrical panels. The terminals are identified by the usual numbering on the relay body or socket, which helps keep troubleshooting straightforward later.\u003c\/p\u003e\u003cp\u003eIt is a 12V coil relay with a specified maximum coil voltage of 18V, so it is not a direct substitute for 24V coil relays. If your boat is 24V, confirm you have a 12V control feed available before ordering.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eMount the relay where it stays out of direct spray and away from bilge water, using a supported socket or harness so the terminals are not carrying strain. Keep wiring runs to the load as short as practical and secure the harness so vibration does not work the connections loose.\u003c\/p\u003e\u003cp\u003eBecause the coil is diode-suppressed, the coil terminals are polarity-sensitive. Follow the + and - markings on the relay or socket when wiring the control side to avoid reverse connection.\u003c\/p\u003e\u003ch6\u003eElectrical and system integration\u003c\/h6\u003e\u003cp\u003eUse the relay so the high-current path stays close to your battery distribution or breaker panel, while the helm switch or control output only energizes the coil. Size wire gauge and overcurrent protection for the actual load and duty cycle, and keep continuous current within the stated contact ratings, especially in warmer compartments.\u003c\/p\u003e\u003cp\u003eLarge start-up surges are normal with motors and some lighting loads. The relay is specified for high inrush, but clean crimps, tight terminals, and correct fusing are still what make the system behave on the water.\u003c\/p\u003e\u003ch6\u003eUse cases on board\u003c\/h6\u003e\u003cp\u003eCommon uses include switching deck and cockpit lights, horns, ventilation fans, solenoids, and pump circuits where you want the control wiring to stay light while the load wiring stays short. It also fits well when an electronics output is only meant to trigger a relay coil, not carry load current directly.\u003c\/p\u003e\u003cp\u003eThis relay makes the most sense for owners who want a tidy, serviceable wiring layout and an easy-to-find standard footprint when replacements are needed later.\u003c\/p\u003e\u003ch6\u003eMaintenance and troubleshooting\u003c\/h6\u003e\u003cp\u003eIf a circuit cuts out under load, check the socket for heat discoloration, loose terminals, and corrosion before blaming the relay itself. A relay that clicks but does not pass power often points to a poor crimp, a loose spade in the socket, or a load that is pushing past the contact rating.\u003c\/p\u003e\u003cp\u003eIf the relay does not energize after a wiring change, confirm coil polarity at the socket since diode suppression requires correct + and - orientation.\u003c\/p\u003e","brand":"Hella Marine","offers":[{"title":"Default Title","offer_id":52269009961141,"sku":"QBP513817","price":12.24,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1298670_qbp513817.jpg?v=1771541448"},{"product_id":"qbp513890","title":"Hella Marine Mini ISO SPDT Relay, 24V, 20A N\/O, 10A N\/C, 6.3mm Blade Terminals, IP54","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Hella Marine 007903001 is a 24 V relay with a 20 A rating and a five terminal blade connection layout for quick, secure wiring.\u003c\/p\u003e\u003cp\u003eIt is a practical way to switch a higher current load from a smaller helm switch, an automation output, or another low current control circuit. The changeover contact set lets you wire either normally open or normally closed behavior, which helps when you need a device to default to on or default to off when the coil is not energized.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e24 V coil for 24 V onboard electrical systems\u003c\/li\u003e\n\u003cli\u003e20 A rating for common accessory loads\u003c\/li\u003e\n\u003cli\u003eSingle pole, changeover (SPDT) contact set for normally open or normally closed wiring\u003c\/li\u003e\n\u003cli\u003eFive blade terminals for standard push on electrical connectors\u003c\/li\u003e\n\u003cli\u003eUseful for keeping long control runs low current while the load wiring stays short and properly protected\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eMount the relay where wiring stays tidy and supported, typically inside a dry electrical space, behind a helm panel, or in a protected relay block. Use correctly sized female blade connectors that fit tightly, add strain relief so vibration does not work the terminals loose, and label the conductors so future troubleshooting is straightforward.\u003c\/p\u003e\u003ch6\u003eElectrical and system integration\u003c\/h6\u003e\u003cp\u003ePlan the circuit so the relay switches the load feed while your control side only powers the coil. Protect the load circuit with an appropriately sized fuse or breaker near the power source, and confirm the actual running current and startup surge of the device you are switching so the relay rating is not being pushed in real use.\u003c\/p\u003e\u003ch6\u003eUse cases on board\u003c\/h6\u003e\u003cp\u003eThis relay is a good match for 24 V boats that need clean switching for accessories such as deck or spreader lights, ventilation blowers, small pumps, and other intermittent loads that fit within the current rating. It also works well when an electronics trigger or a control panel output needs to operate a separate power circuit without routing heavy current through the switchgear.\u003c\/p\u003e","brand":"Hella Marine","offers":[{"title":"Default Title","offer_id":52269010387125,"sku":"QBP513890","price":12.24,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1298675_qbp513890.jpg?v=1771541450"},{"product_id":"qbp513933","title":"Hella Marine Mini ISO Relay, 12V, 40A, 5-Pin, SPDT, Weatherproof","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Hella Marine 007794911 is a 12V Mini ISO relay for switching higher-current circuits like driving lights and fog lights from a low-current helm or dash switch. It is rated for 40A continuous load and uses an SPDT\/Form C contact set with 5 terminals, so it can run a simple on\/off circuit or a changeover circuit where one feed is switched between two outputs.\u003c\/p\u003e\u003cp\u003eThis style of relay is commonly used on boats to keep the high-current wiring run short and protected, while the switch at the helm only carries the coil current. The included weatherproof cover and mounting bracket make it easier to mount the relay in places that see moisture and vibration, such as under a console, inside a locker, or near an electrical distribution area.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e12V DC coil with 40A continuous switching capacity\u003c\/li\u003e\n\u003cli\u003eSPDT\/Form C changeover contacts for normally open or normally closed wiring\u003c\/li\u003e\n\u003cli\u003e5-pin Mini ISO footprint to match common relay sockets and harnesses\u003c\/li\u003e\n\u003cli\u003eWeatherproof cover to shield the relay body and terminals from damp air and spray\u003c\/li\u003e\n\u003cli\u003eMounting bracket for securing the relay to a bulkhead or panel\u003c\/li\u003e\n\u003cli\u003eResistor coil suppression to help tame voltage spikes on the control side\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eWhat’s included\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eMini ISO relay (12V, 40A, SPDT\/Form C)\u003c\/li\u003e\n\u003cli\u003eWeatherproof cover\u003c\/li\u003e\n\u003cli\u003eMounting bracket\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and wiring notes\u003c\/h6\u003e\u003cp\u003eMount the relay where it stays accessible for troubleshooting and where the cover can be seated properly over the terminals. In most lighting installs, the relay is placed close to the fused power feed or close to the load to keep higher-current cable runs short and tidy.\u003c\/p\u003e\u003cp\u003eSize the fuse, wire, and terminals to the actual load, and use properly crimped connections that are sealed for the marine environment. After wiring, check for heat at the terminals under load, then secure the harness so vibration does not work the connections loose over time.\u003c\/p\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis relay is for 12V DC systems. It uses a 5-terminal Mini ISO layout, so it pairs with standard 5-pin Mini ISO sockets and pre-wired pigtails. If your circuit only needs a basic on\/off function, it can be wired using the common and normally open terminals while leaving the changeover terminal unused.\u003c\/p\u003e\u003ch6\u003eUse on board\u003c\/h6\u003e\u003cp\u003eIt is a practical choice for auxiliary driving lights, fog lights, spreader lights, and other add-on lighting where you want full battery-fed current at the load without routing that current through the helm switch. It also helps when you are building a cleaner relay panel for refits, repowers, or new electronics and lighting additions.\u003c\/p\u003e","brand":"Hella Marine","offers":[{"title":"Default Title","offer_id":52269011075253,"sku":"QBP513933","price":14.69,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1298678_qbp513933.jpg?v=1771541453"},{"product_id":"qbp514039","title":"Hella Marine DE3175 Festoon Replacement Bulb, SV8.5-8 Base, 12V, 10W","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Hella Marine 002091361 is a 12V, 10W clear festoon replacement bulb with an SV8.5-8 base for fixtures that use this style of end-cap bulb.\u003c\/p\u003e\u003cp\u003eIt is commonly used in navigation lights and interior lamps that take an SV8.5-8 festoon, keeping the original light color and beam pattern that the fixture was built around.\u003c\/p\u003e\u003cp\u003eFor best results, confirm your onboard supply is 12V DC and that the light is rated for a 10W bulb (about 0.8A draw at 12V).\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e12V, 10W festoon bulb with SV8.5-8 end caps\u003c\/li\u003e\n\u003cli\u003eClear glass for the same light color your lens and filter expect\u003c\/li\u003e\n\u003cli\u003eDrop-in fit for fixtures that use an SV8.5-8 festoon holder, including many navigation and interior lights\u003c\/li\u003e\n\u003cli\u003eAbout 0.8A current draw at 12V, useful when checking fuse and circuit loading\u003c\/li\u003e\n\u003cli\u003eSimple replacement that does not change wiring, switches, or housings\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eMatch the base style first: SV8.5-8 festoons use spring contacts on each end, not wedge or bayonet sockets. If your old bulb has the base code printed on the metal cap or the fixture calls for SV8.5-8, this is the correct fit.\u003c\/p\u003e\u003cp\u003eBecause festoon lengths vary, compare the old bulb end-to-end before ordering if your fixture has tight tolerances.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eTurn off power at the switch and, if possible, the breaker. Let the lens and bulb cool before handling. Remove the lens, then compress one end of the bulb into the spring contact and seat the opposite end.\u003c\/p\u003e\u003cp\u003eClean any green corrosion from the contacts so the bulb seats firmly; poor contact is a common cause of flicker on boats.\u003c\/p\u003e\u003ch6\u003eUse cases on board\u003c\/h6\u003e\u003cp\u003eThis bulb suits 12V boats that still run traditional festoon lamps in navigation lights, cabin domes, chart lights, and courtesy fixtures where the housing is built around an SV8.5-8 bulb and a 10W load.\u003c\/p\u003e\u003cp\u003eIt is a good match when you want a like-for-like replacement without changing fixtures or dealing with LED polarity and dimmer compatibility.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eKeep the lens gasket and venting in good shape so moisture does not sit in the fixture. If you routinely wash down with saltwater, a quick rinse of the lens area and an occasional contact check will help prevent future failures.\u003c\/p\u003e","brand":"Hella Marine","offers":[{"title":"Default Title","offer_id":52269011337397,"sku":"QBP514039","price":0.86,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1298682_qbp514039.jpg?v=1771541454"},{"product_id":"qbp486633","title":"Hella Marine SV8.5-8 Base Festoon Bulb, 12V, 10W, 10x41mm, Clear","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Hella Marine 178560181 is a 12V, 10W clear festoon replacement bulb with an SV8.5-8 base for navigation and interior light fixtures. It uses the double-ended festoon format (about 10 x 41 mm), so it seats in spring clips at each end rather than a bayonet socket. On a 12V DC system it adds a 10W load, which is helpful when you are budgeting lighting circuits.\u003c\/p\u003e\u003cp\u003eThis is a straightforward swap when your fixture calls for an SV8.5-8 festoon bulb, including many compact navigation lamps and small interior lights. Match the length and end style to the bulb you are replacing, since festoon bulbs come in several sizes that look similar at a glance.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e12V DC, 10W clear festoon replacement bulb\u003c\/li\u003e\n\u003cli\u003eSV8.5-8 double-ended base for spring-clip festoon holders\u003c\/li\u003e\n\u003cli\u003eApprox. 10 x 41 mm size for fixtures built around the 41 mm festoon format\u003c\/li\u003e\n\u003cli\u003eCommon fit for navigation and interior fixtures that specify an SV8.5-8 festoon lamp\u003c\/li\u003e\n\u003cli\u003eUsed in various compact navigation lights, including Hella 3562 series fixtures that take an SV8.5 festoon bulb\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eUse this bulb in 12V fixtures that specify an SV8.5-8 festoon (double-ended) lamp. If your light takes a BA15s or BAY15d bayonet bulb, or a different festoon length, it will not seat correctly.\u003c\/p\u003e\u003cp\u003eIt is commonly found in compact navigation lights and small interior lamps. On boats with a 24V house system, confirm the fixture is fed from a 12V circuit before ordering.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eShut off the light circuit at the switch or breaker and let the old bulb cool. Open the lens, release the bulb from the spring clips, and snap the new bulb into place so both ends are fully seated. Before closing the lens, clean any salt film from the contacts and make sure the gasket is sitting flat to help keep moisture out of the fixture.\u003c\/p\u003e\u003ch6\u003eUse on board\u003c\/h6\u003e\u003cp\u003eThis bulb is a good match for owners keeping existing incandescent navigation or interior lights in service and wanting the same form factor the fixture was built around. It is commonly used for small running lights, cabin lights, and chart table or utility fixtures that rely on the 41 mm festoon format.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eIncandescent bulbs do not like heat buildup or loose contact, so it helps to keep the fixture closed tightly and the terminals clean. Carrying a spare on board makes quick work of an unexpected light-out before an evening run.\u003c\/p\u003e","brand":"Hella Marine","offers":[{"title":"Default Title","offer_id":52269026148533,"sku":"QBP486633","price":0.88,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1298446_qbp486633.jpg?v=1771541494"},{"product_id":"qbp486790","title":"Hella Marine SV8.5-8 Festoon Bulb, 24V 10W, 11x41mm","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Hella Marine 178560281 is a 24V 10W incandescent festoon replacement bulb with an SV8.5-8 base in an 11 x 41 mm size. It’s the style used in many traditional navigation light and interior lamp fixtures that take spring-loaded festoon end caps.\u003c\/p\u003e\u003cp\u003eThis is a straightforward drop-in bulb for 24V DC onboard systems. Match the base style and overall length to your existing lamp, then you’re back to full function without changing the fixture or wiring.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e24V, 10W incandescent festoon bulb (6429 type) for 24V DC electrical systems\u003c\/li\u003e\n\u003cli\u003eSV8.5-8 end-cap base with 11 x 41 mm overall size for common festoon holders\u003c\/li\u003e\n\u003cli\u003eClear bulb that outputs white light through your existing lens\u003c\/li\u003e\n\u003cli\u003eNo polarity concerns and no external driver or electronics\u003c\/li\u003e\n\u003cli\u003eUseful spare to keep onboard for quick restoration of navigation or interior lighting\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eConfirm three things before ordering: system voltage (24V), festoon base style (SV8.5-8), and the physical size (11 x 41 mm). If your fixture is 12V, a 24V bulb will be noticeably dim, so voltage match matters just as much as length.\u003c\/p\u003e\u003cp\u003eFestoon holders vary by a few millimeters and by how the spring contacts grab the end caps. If your current lamp sits tightly between the contacts and clears the lens, this bulb is the right format.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eSwitch off power at the panel, let the existing bulb cool, then remove it by compressing one spring contact and lifting the bulb out. Seat the new bulb evenly between both end contacts so it can’t rattle loose in chop or vibration.\u003c\/p\u003e\u003cp\u003eOn exterior fixtures, check that the lens and gasket are clean and seated after replacement so spray and washdowns stay out of the housing.\u003c\/p\u003e\u003ch6\u003eUse on board\u003c\/h6\u003e\u003cp\u003eThis bulb makes sense for boats running classic festoon-based navigation lights or interior lamps on 24V systems, where you want a direct replacement that keeps the original look and beam pattern through the fixture’s lens.\u003c\/p\u003e\u003ch6\u003eWhat’s included\u003c\/h6\u003e\u003cul\u003e\u003cli\u003e1 x replacement bulb\u003c\/li\u003e\u003c\/ul\u003e","brand":"Hella Marine","offers":[{"title":"Default Title","offer_id":52269026181301,"sku":"QBP486790","price":0.88,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1298448_qbp486790.jpg?v=1771541496"},{"product_id":"qbp486815","title":"Hella Marine H5W Miniature Halogen Bulb, 12V, 5W, BA9s","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Hella Marine 211738711 is a 12V miniature halogen replacement bulb in the H5W format.\u003c\/p\u003e\u003cp\u003eIt is used anywhere your boat light calls for an H5W miniature bulb and you want to keep the same halogen lamp type in the fixture. This is commonly seen in compact interior lights like map and reading positions, small courtesy lights, and instrument or switch lighting, but the final check is the marking on the old bulb and the socket it came out of.\u003c\/p\u003e\u003cp\u003eHalogen bulbs run hot in operation. Let the fixture cool before swapping the lamp, avoid touching the glass with bare fingers, and make sure the lens and surrounding wiring are not pressed against the bulb.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e12V miniature halogen replacement bulb (H5W format)\u003c\/li\u003e\n\u003cli\u003eRestores output and beam pattern for fixtures that specify an H5W lamp\u003c\/li\u003e\n\u003cli\u003eSimple swap when a bulb has darkened or failed, with no rewiring\u003c\/li\u003e\n\u003cli\u003eUseful spare to keep aboard for night runs and cabin lighting\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eMatch system voltage (12V) and the bulb type marking (H5W) to your existing lamp. If your fixture uses a different base style or a different wattage rating, stick with the bulb specified for that light to avoid heat issues and poor fit.\u003c\/p\u003e\u003ch6\u003eInstallation and handling\u003c\/h6\u003e\u003cp\u003eSwitch power off at the panel and let the fixture cool. Remove the lens or access cover, then remove the old bulb using the same motion required by the socket style. Install the new bulb fully seated, refit the lens, and test the light before closing everything up.\u003c\/p\u003e\u003ch6\u003eUse on board\u003c\/h6\u003e\u003cp\u003eThis bulb is a good match for owners maintaining older halogen-based interior lighting, as well as charter and fishing boats that keep spare lamps on hand for quick fixes. It also makes sense for any cabin or helm light where you want a direct replacement without changing the fixture.\u003c\/p\u003e","brand":"Hella Marine","offers":[{"title":"Default Title","offer_id":52269026214069,"sku":"QBP486815","price":6.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1298450_qbp486815.jpg?v=1771541497"},{"product_id":"qbp486822","title":"Hella Marine H3 Replacement Halogen Bulb, 12V, 55W, PK22s Base","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Hella Marine 178555061 is a 12V, 55W H3 halogen replacement bulb for deck floodlights and search lights that use an H3 (PK22s) base. It is meant for 12V DC lighting circuits and draws about 4.6A at full output, so it is a like for like swap when you are replacing the same voltage and wattage bulb.\u003c\/p\u003e\u003cp\u003eThis is the bulb only, so any sealing against spray and washdowns comes from the light fixture itself. Before ordering, check the markings on your existing bulb and confirm the fixture calls for a 12V, 55W H3 bulb with the same base style.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e12V, 55W H3 halogen bulb for common marine floodlight and search light applications\u003c\/li\u003e\n\u003cli\u003eH3 (PK22s) base style for the correct fit in fixtures built around this socket and retainer\u003c\/li\u003e\n\u003cli\u003eLike for like electrical load for 12V circuits, about 4.6A at 55W\u003c\/li\u003e\n\u003cli\u003eWorks as a replacement lamp in lights that use H3 bulbs, including many deck floodlights and search lights\u003c\/li\u003e\n\u003cli\u003eSimple bulb swap when the filament fails or output drops, with no wiring changes\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eMatch three things on the existing bulb and the light label: base type (H3), system voltage (12V), and wattage (55W). If the fixture calls for a different voltage or wattage, use the correct bulb for that fixture to avoid poor performance or overheating.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eSwitch off power at the breaker and let the light cool fully before opening the housing. Remove the old bulb, install the new H3 bulb in the same orientation, and make sure the retainer and electrical connection are fully seated before closing the fixture.\u003c\/p\u003e\u003cp\u003eHalogen bulbs run hot, and oils from skin can create hot spots on the glass. Handle the bulb with clean gloves or a tissue, and wipe it down if it is touched before reassembly.\u003c\/p\u003e\u003ch6\u003eUse cases on board\u003c\/h6\u003e\u003cp\u003eThis bulb is a good match for boats running 12V halogen deck floodlights and search lights where a fast replacement matters for night docking, loading gear, or checking rigging and deck areas after dark. Keeping a spare onboard can save a trip when a filament fails at the wrong time.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eIf you are seeing repeated bulb failures, inspect the fixture for water intrusion, heat damage at the connector, or a loose retainer that lets the bulb vibrate. Cleaning the lens and reflector inside the light housing can also help get the most usable light from a fresh bulb.\u003c\/p\u003e","brand":"Hella Marine","offers":[{"title":"Default Title","offer_id":52269026246837,"sku":"QBP486822","price":4.9,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1298451_qbp486822.jpg?v=1771541499"},{"product_id":"qbp486856","title":"Hella Marine H3 Search Light Bulb, 12V, 100W, PK22s Base","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Hella Marine 178555924 is an H3 replacement bulb for 12V lighting with a 100W rating and a PK22s base.\u003c\/p\u003e\u003cp\u003eIt is used in halogen deck floodlights, searchlights, and other fixtures that specify an H3 bulb. Because 100W is a heavy load on a 12V circuit, confirm the light housing is rated for the wattage and that your wiring and switching can handle about 8.3A per lamp.\u003c\/p\u003e\u003cp\u003eThis is a straightforward service part for keeping an existing halogen light working without changing the fixture.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eH3 halogen replacement bulb for fixtures that take an H3 lamp\u003c\/li\u003e\n\u003cli\u003e12V, 100W rating for applications that call for a high-wattage H3 bulb\u003c\/li\u003e\n\u003cli\u003ePK22s base to match standard H3 sockets\u003c\/li\u003e\n\u003cli\u003eDraws about 8.3A at 12V, which helps when checking fuse and switch capacity\u003c\/li\u003e\n\u003cli\u003eUseful when you want a like-for-like replacement and do not want to retrofit the light\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eMatch the bulb type and base to your existing lamp before ordering. The simplest check is the marking on the old bulb (H3) and the base style (PK22s). If your fixture uses a retaining clip or a specific lead connection inside the housing, make sure it lines up the same way before closing the lens.\u003c\/p\u003e\u003cp\u003eThis bulb is for 12V DC systems only. It should not be used on 24V circuits.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eShut off power at the breaker or pull the fuse, then let the light cool fully before opening it. Halogen bulbs run hot, and the reflector and lens area can stay warm for a while after use.\u003c\/p\u003e\u003cp\u003eAvoid touching the glass with bare fingers. If you do, wipe it clean before powering up so skin oils do not create hot spots on the quartz.\u003c\/p\u003e\u003cp\u003eAfter reassembly, check that the gasket and lens are seated correctly so spray and washdowns stay outside the housing.\u003c\/p\u003e\u003ch6\u003eElectrical and system integration\u003c\/h6\u003e\u003cp\u003eAt 100W, voltage drop becomes noticeable on long cable runs. Keep connections tight and corrosion-free, and size the circuit for the current draw of the lamp or lamps you are running. A quick functional check after install is steady brightness and no excessive heat at terminals or connectors.\u003c\/p\u003e\u003ch6\u003eUse on board\u003c\/h6\u003e\u003cp\u003eThis bulb is a good match for boats that already have an H3 halogen deck flood or spotlight installed and want a direct service replacement. It is commonly used for dockside lighting, cockpit work, deck loading, and short-duration spotlighting where the existing fixture is already set up for an H3 lamp.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eHalogen bulbs do not like moisture inside the housing. If you see condensation, address the seal or venting so the bulb is not stressed by repeated heat and cool cycles. Keeping the lens clean also helps the fixture run cooler for the same usable light.\u003c\/p\u003e","brand":"Hella Marine","offers":[{"title":"Default Title","offer_id":52269026476213,"sku":"QBP486856","price":4.9,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1298452_qbp486856.jpg?v=1771541500"},{"product_id":"qbp486919","title":"Hella Marine H3 Halogen Replacement Bulb, 24V, 70W, PK22s Base","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Hella Marine 178555241 is a 24V, 70W H3 halogen replacement bulb for deck floodlamps and search lights that run on a 24V system. At 70W it draws about 3A, so it is a good match when you need the same output your fixture was built around without changing wiring, fusing, or heat load.\u003c\/p\u003e\u003cp\u003eThis is an H3 lamp with a PK22s base, so fit is defined by the bulb type and base style as much as voltage and wattage. If your light calls out H3 24V 70W on the housing, manual, or existing bulb, this is the correct format to replace it.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e24V, 70W H3 halogen bulb for marine deck lights and search lights that specify this lamp format\u003c\/li\u003e\n\u003cli\u003ePK22s base style to match H3 fixtures that use the keyed metal base\u003c\/li\u003e\n\u003cli\u003eApproximately 3A draw at 24V, helpful for confirming circuit and switch loading\u003c\/li\u003e\n\u003cli\u003eHalogen light output that stays white and focused when used with the fixture reflector and lens\u003c\/li\u003e\n\u003cli\u003eDirect replacement when the existing lamp is marked H3 24V 70W, with no changes to the light housing\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eMatch three things before ordering: bulb type (H3), system voltage (24V), and wattage (70W). Swapping a 12V bulb into a 24V circuit can fail instantly, and fitting a different wattage can change beam performance and heat inside the housing.\u003c\/p\u003e\u003cp\u003eAlso confirm the base style. H3 bulbs commonly use a PK22s base and a lead connection, so check that your fixture uses the same keyed base and terminal arrangement as the bulb you are removing.\u003c\/p\u003e\u003ch6\u003eInstallation and handling\u003c\/h6\u003e\u003cp\u003eShut power off at the breaker and let the light cool before opening the housing. Halogen bulbs run hot, and a hot lens or reflector can hold heat longer than you expect in an enclosed flood or search light.\u003c\/p\u003e\u003cp\u003eHandle the bulb by the base. Avoid touching the glass with bare fingers; oils can create hot spots on the quartz envelope. Seat the base fully, secure the retainer, and make sure the lead connection is snug and routed so it cannot chafe against the reflector or pinch under the cover.\u003c\/p\u003e\u003ch6\u003eUse on board\u003c\/h6\u003e\u003cp\u003eThis bulb makes the most sense on boats and workboats with 24V lighting circuits where deck work lights or a search light need consistent output for docking, line handling, and spotting channel markers at night. Keeping a spare on board can cut downtime when a deck flood or search light is critical to your routine.\u003c\/p\u003e\u003ch6\u003eMaintenance and spares\u003c\/h6\u003e\u003cp\u003eAfter replacement, clean the lens and inspect gaskets so spray and washdowns do not leave salt inside the housing. If you see moisture or discoloration inside the lens, address the seal before the new bulb spends hours cooking trapped humidity.\u003c\/p\u003e","brand":"Hella Marine","offers":[{"title":"Default Title","offer_id":52269026672821,"sku":"QBP486919","price":3.06,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1298453_qbp486919.jpg?v=1771541502"},{"product_id":"qbp486953","title":"Hella Marine 6451 SV8.5-8 Incandescent Bulb, 12V, 15W, 17x41mm","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Hella Marine 358107592 is a 12V, 15W festoon replacement bulb in the SV8.5-8 (6451 \/ C5W) format.\u003c\/p\u003e\u003cp\u003eIt uses the common 41 mm festoon length found in many Hella Marine navigation, courtesy, and interior fixtures that clamp the bulb between spring contacts at each end. It is intended for 12V DC systems only, so confirm your light is not wired for 24V before installing.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e12V, 15W incandescent bulb for standard onboard DC lighting circuits\u003c\/li\u003e\n\u003cli\u003eSV8.5-8 festoon end caps (trade number 6451 \/ C5W) for fixtures that hold the bulb at both ends\u003c\/li\u003e\n\u003cli\u003e41 mm overall length for the common 15 x 41 mm festoon size used in many marine light housings\u003c\/li\u003e\n\u003cli\u003eClear glass for the familiar white incandescent light output\u003c\/li\u003e\n\u003cli\u003eNon-polarized fit, so it will light regardless of which way it is installed\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eMatch this bulb to your existing lamp by checking three things: system voltage, festoon end-cap style (SV8.5-8), and length. If your old bulb measures around 41 mm end-to-end and sits in spring clips, this is the same format. If your fixture takes a bayonet, wedge, or screw base, it will not fit.\u003c\/p\u003e\u003ch6\u003eInstallation and handling\u003c\/h6\u003e\u003cp\u003eSwitch the circuit off and let the lens cool before opening the fixture. Seat one end cap into the spring contact, compress slightly, then drop the other end into place so both contacts land squarely. Clean, dry fingers or a cloth help keep the glass free of oils that can bake on over time.\u003c\/p\u003e\u003ch6\u003eUse cases on board\u003c\/h6\u003e\u003cp\u003eThis bulb is a good match for boaters maintaining existing incandescent navigation or interior lights and for keeping a spare aboard for quick swaps at the dock or underway. It is also handy when troubleshooting a dim light, since a fresh bulb helps separate wiring issues from a tired lamp.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eIf a festoon lamp flickers on rough water, check that the spring contacts still grip the end caps firmly and that the contacts are clean. Any corrosion on the contacts should be removed carefully so the bulb seats tight and runs cooler.\u003c\/p\u003e","brand":"Hella Marine","offers":[{"title":"Default Title","offer_id":52269027295413,"sku":"QBP486953","price":1.47,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1298456_qbp486953.jpg?v=1771541504"},{"product_id":"qbp512557","title":"Hella Marine 2492 Deck Mount All-Round Navigation Light, 12V, 2NM Visibility, 10W Bulb, Black Base","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Hella Marine 002492201 is a 12V all-round white navigation light for deck mounting, rated for 2 nautical mile visibility on vessels up to 12 m (39.4 ft). It uses a single 10W bulb and draws 0.83A, which keeps load predictable on smaller DC systems.\u003c\/p\u003e\u003cp\u003eThis light mounts on a flat surface and takes up little space with a 2-5\/16 in diameter body that stands 2-5\/8 in high (59 x 67 mm). The polycarbonate housing and gasketed lens help keep spray out, and the unit is non-magnetic for cleaner installs around compasses and sensitive electronics.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eAll-round 360 degree white light with 2 nautical mile visibility\u003c\/li\u003e\n\u003cli\u003eFor vessels up to 12 m (39.4 ft)\u003c\/li\u003e\n\u003cli\u003e12V DC, 10W bulb, 0.83A current draw\u003c\/li\u003e\n\u003cli\u003ePolycarbonate housing with a gasketed lens to reduce water intrusion\u003c\/li\u003e\n\u003cli\u003eUV-resistant housing and lens for exposed mounting locations\u003c\/li\u003e\n\u003cli\u003eNon-magnetic construction\u003c\/li\u003e\n\u003cli\u003eTwo 6.3 mm flat plug connectors for straightforward wiring\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and wiring\u003c\/h6\u003e\u003cp\u003ePlan the mounting point so the lens has an unobstructed 360 degree view and sits clear of antennas, rails, rocket launchers, and canvas. Fasteners are not included, so match screw length and bedding method to your deck thickness and core type.\u003c\/p\u003e\u003cp\u003eWiring is via two 6.3 mm flat plug connectors. Tie it into a properly fused navigation or anchor-light circuit on your 12V panel, and seal any deck penetrations so water cannot track into the laminate.\u003c\/p\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis light is a good match for smaller powerboats and sailboats that need an all-round white light for anchoring or general all-round visibility. The black base blends in on dark hardware and painted surfaces without drawing attention during the day.\u003c\/p\u003e\u003ch6\u003eMaintenance and spares\u003c\/h6\u003e\u003cp\u003eRinse salt off the housing and lens after heavy spray or washdowns, and clean with mild soap to keep the optics clear. Replacement parts are available if needed, including bulb 288904 and replacement lens 63100.\u003c\/p\u003e\u003ch6\u003eWhat’s included\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eAll-round white navigation light assembly (black base and lens)\u003c\/li\u003e\n\u003cli\u003e10W bulb\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Hella Marine","offers":[{"title":"Default Title","offer_id":52269030899893,"sku":"QBP512557","price":39.17,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1298653_qbp512557.jpg?v=1771541525"},{"product_id":"qbp512637","title":"Hella Marine 3562 Stern Navigation Light, Incandescent, 2NM, 12V, White Housing","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Hella Marine 003562115 is a stern navigation lamp with a white housing for 12V boats, using an incandescent 12V 10W SV8.5 bulb and a 2 nautical mile visible range. It mounts vertically on a flat surface at the aft end of the boat and routes wiring through the base with a rubber-grommet entry.\u003c\/p\u003e\u003cp\u003eThe housing and lens are UV and impact resistant plastic with an IP54 rating, and the construction is non-magnetic and saltwater resistant. Its snap-lock housing opens for quick bulb access without tools, which is handy when a globe needs replacing at the dock or between night runs.\u003c\/p\u003e\u003cp\u003eAt roughly 3 in high, 2.5 in wide, and 2.06 in deep, it fits well on transoms and other tight stern locations where you want a clean, low-profile light that is easy to service.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eWhite stern navigation light rated for 2 nautical mile visibility\u003c\/li\u003e\n\u003cli\u003e12V incandescent lamp with a 12V 10W SV8.5 bulb\u003c\/li\u003e\n\u003cli\u003eVertical surface-mount format for transoms and other flat stern faces\u003c\/li\u003e\n\u003cli\u003eSnap-lock housing for tool-free bulb access\u003c\/li\u003e\n\u003cli\u003eCable entry through the base plate with a rubber grommet to protect wiring\u003c\/li\u003e\n\u003cli\u003eUV and impact resistant plastic housing and lens with an IP54 rating\u003c\/li\u003e\n\u003cli\u003eNon-magnetic, saltwater resistant build to reduce compass interference and stand up to marine exposure\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis light is for 12V DC navigation-light circuits. Plan the mounting position so the lens has a clear view aft and is not blocked by swim steps, davits, outboard cowls, or stern rails that could shadow the light underway.\u003c\/p\u003e\u003cp\u003eIt is a good match for boaters who want a vertical stern light in a compact footprint and prefer simple bulb access for routine maintenance.\u003c\/p\u003e\u003ch6\u003eInstallation and wiring\u003c\/h6\u003e\u003cp\u003eMount the base on a flat, vertical surface and route the conductors through the base opening. The through-base cable entry helps keep the wiring tidy and reduces exposure at the exit point, especially when paired with marine-grade cable protection and properly sealed fasteners.\u003c\/p\u003e\u003cp\u003eConnect to your existing navigation light switch or breaker and make terminations with marine-grade connectors and heat-shrink where appropriate. After installation, verify the light is secure and properly aligned, then check operation from the helm.\u003c\/p\u003e\u003ch6\u003eCompliance and approvals\u003c\/h6\u003e\u003cp\u003eThis stern lamp carries approvals for IMO Col Reg 72 and is also approved to USCG and ABYC A-16, with additional approval markings including RINA and Maritime NZ.\u003c\/p\u003e\u003ch6\u003eMaintenance and bulb service\u003c\/h6\u003e\u003cp\u003eKeep the lens clean so the light output stays crisp at night, especially after salt spray and soot from the exhaust settles on the stern. When the bulb needs replacement, open the snap-lock housing, swap the globe, and inspect the wiring entry and seals before closing the unit back up.\u003c\/p\u003e","brand":"Hella Marine","offers":[{"title":"Default Title","offer_id":52269033455797,"sku":"QBP512637","price":31.11,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1298655_qbp512637.jpg?v=1771541528"},{"product_id":"qbp512782","title":"Hella Marine Series 2984 All-Round Navigation Light, Red Light, 2 NM, 12V, Black Housing","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Hella Marine 002984525 is an all-round red navigation lamp with a 360 degree light arc, a black housing that is non-magnetic, and a 2 nautical mile visibility rating. It uses a replaceable 12V \/ 25W BAY15d incandescent bulb and carries an IP55 rating for rain and spray.\u003c\/p\u003e\u003cp\u003eThis style of 2 NM all-round lamp is commonly specified on vessels under 20 m when installed in the correct location and height. The housing and lens are made from plastic that stands up to sun exposure and onboard knocks, and the lamp body is built for saltwater use.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eAll-round red light (360 degree) with a 2 nautical mile visibility rating\u003c\/li\u003e\n\u003cli\u003eBlack housing that is non-magnetic and suited to saltwater exposure\u003c\/li\u003e\n\u003cli\u003eIP55-rated enclosure for wet weather and deck spray\u003c\/li\u003e\n\u003cli\u003eHorizontal surface mount with cable entry through the base plate and a rubber grommet\u003c\/li\u003e\n\u003cli\u003eBayonet-lock style housing for quick access, supplied with a 12V \/ 25W BAY15d bulb\u003c\/li\u003e\n\u003cli\u003eVertically hanging bulb layout with contacts positioned high in the lamp to help reduce corrosion at the terminals\u003c\/li\u003e\n\u003cli\u003eMeets IMO Col Reg 72 and USCG requirements, with ABYC A-16, BSH, and Maritime NZ approvals listed\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eMount the base on a flat horizontal surface where the lamp can show a full 360 degree arc without being shadowed by antennas, canvas, radar arches, or rigging. If it is being hoisted up a mast, make sure it stays upright so the lens and bulb orientation remain correct.\u003c\/p\u003e\u003cp\u003eThe cable routes through the base, so plan the run before fastening the unit down. Leave a drip loop, support the wire so vibration does not work it loose, and seal around fasteners and the cable pass-through as you would for any deck-mounted electrical fitting.\u003c\/p\u003e\u003ch6\u003eElectrical and bulb notes\u003c\/h6\u003e\u003cp\u003eThis is an incandescent navigation lamp that runs with a BAY15d bulb. The included lamp is 12V \/ 25W; on a 24V boat, the same fixture can be used by fitting a compatible 24V BAY15d bulb rather than feeding 24V to a 12V lamp.\u003c\/p\u003e\u003cp\u003eProtect the circuit with an appropriately sized fuse or breaker for the wiring and load, and keep connections dry and well-supported behind the mounting surface.\u003c\/p\u003e\u003ch6\u003eUse cases on board\u003c\/h6\u003e\u003cp\u003eThis lamp suits sailboats and powerboats that need an all-round red signal in a location like a mast, hardtop, or cabin roof, and want a serviceable bulb-type light in a black housing that does not stand out against dark rigging or hardware.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eRinse salt off the lens and housing during routine washdowns so light output stays consistent. When changing bulbs, check that the bayonet-lock housing seats cleanly and that the cable grommet remains snug to keep spray out of the wiring cavity.\u003c\/p\u003e","brand":"Hella Marine","offers":[{"title":"Default Title","offer_id":52269033914549,"sku":"QBP512782","price":116.98,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1298656_qbp512782.jpg?v=1771541532"},{"product_id":"qbp513235","title":"Hella Marine Mini LED Warning Lightbar, 10in, 12-24V, Fixed Mount, Clear Lens, Amber Light","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Hella Marine 014566111 is a low-profile LED warning light bar that throws a 360-degree amber signal on 10 to 30 V DC systems, so it works on both 12V and 24V boats.\u003c\/p\u003e\u003cp\u003eThis is the Micro Lightbar size with a clear dome and bracket mounting. It measures about 255 mm long by 156 mm wide and stands roughly 49 mm tall, and it weighs about 691 g, which helps it fit on a hardtop, cabin roof, radar arch, or equipment rack. Power draw is up to about 70 W (around 6.2 A at 12 V or 2.9 A at 24 V), and the housing and dome are polycarbonate with polarity-reversal protection. Ingress protection ratings include IP6X and IPX9K for heavy spray and high-pressure washdowns.\u003c\/p\u003e\u003cp\u003eThe selectable patterns include flashing and rotating modes. This type of light is used as an attention signal during towing, dock operations, deck work, and other situations where an amber warning beacon is appropriate. It is not a navigation light and it should not be used in place of required running lights.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eMulti-voltage 10 to 30 V DC input for 12V and 24V electrical systems\u003c\/li\u003e\n\u003cli\u003e360-degree amber warning output through a clear lens\u003c\/li\u003e\n\u003cli\u003eUser-selectable patterns, including flashing and rotating modes\u003c\/li\u003e\n\u003cli\u003eUp to about 70 W draw, with typical current around 6.2 A at 12 V or 2.9 A at 24 V\u003c\/li\u003e\n\u003cli\u003ePolycarbonate dome and housing with polarity-reversal protection and vibration protection\u003c\/li\u003e\n\u003cli\u003eProtection class listed as IP6X, IPX4K, and IPX9K for dust and water spray, including high-pressure cleaning\u003c\/li\u003e\n\u003cli\u003eBracket mounting configuration with a stainless steel mounting bracket and foam foot cushions to protect the mounting surface\u003c\/li\u003e\n\u003cli\u003eType approval and EMC notes: SAE J845 Class 1, ECE-R10, CISPR 25 Class 3\u003c\/li\u003e\n\u003cli\u003eOperating temperature range from -40 C to +65 C\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eMount the bracket on a flat, solid surface with enough clearance for a full 360-degree view. On boats, that usually means above head height on the hardtop, cabin roof, or an arch so antennas and rails do not block the signal.\u003c\/p\u003e\u003cp\u003ePlan wiring before you drill. Fixed-mount versions use a short lead (about 500 mm), so most installs land in a nearby junction box or under the headliner and then run a longer marine-grade cable back to the DC distribution. Protect the circuit with an appropriately sized fuse or breaker at the power source and switch it from the helm or a dedicated work panel.\u003c\/p\u003e\u003cp\u003eAfter the first few trips, recheck fasteners and cable support. Keeping the wiring strain-relieved matters on a boat where vibration and shock loads are routine.\u003c\/p\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eBecause it runs on 10 to 30 V DC, it can be wired into typical 12V center consoles and 24V commercial rigs without a converter. If you are adding it to a mixed-voltage boat, confirm the feed you are tapping matches the control switch and breaker panel.\u003c\/p\u003e\u003cp\u003eWith a footprint around 255 mm by 156 mm and a low overall height, it fits where full-size roof beacons do not. Keep it out of direct line-of-sight at the helm to avoid night glare, and leave room to remove the unit later for service.\u003c\/p\u003e\u003ch6\u003eUse cases on board\u003c\/h6\u003e\u003cp\u003eThis light makes sense for operators who need an amber attention signal for dock work, towing, patrol duties, or deck operations on workboats and tenders. It also works well on fishing boats that raft up or work gear at night and want a clear warning signal for nearby traffic, while still keeping proper navigation lights on.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eRinse salt off after use and clean the polycarbonate dome with mild soap and water. Avoid strong solvents and aggressive polishing compounds that can haze plastics. If the light sees regular washdowns, inspect the mounting surface seal and the cable entry point as part of your seasonal checks.\u003c\/p\u003e","brand":"Hella Marine","offers":[{"title":"Default Title","offer_id":52269034897589,"sku":"QBP513235","price":239.9,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1298662_qbp513235.jpg?v=1771541534"},{"product_id":"qbp513299","title":"Hella Marine Mini LED Warning Lightbar, 10in, 10-30V, IP67, Magnetic Mount, Amber Light, Clear Lens, Flashing\/Rotating Modes","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Hella Marine 014566121 is a 10 inch LED mini warning lightbar with a magnetic mount and an amber light output under a clear dome. It provides a 360-degree warning signal with user-selectable flashing and rotating patterns for situations where you need to be seen clearly on the water.\u003c\/p\u003e\u003cp\u003eIt accepts 10 to 30 V DC input for 12 V and 24 V systems, draws up to 70 W, and is rated for operation from -40°C to +65°C. The dome and housing are polycarbonate, the magnet version uses a 2.5 m cable, and the unit carries IP6K9K and IP6K4K protection ratings for wet conditions and high-pressure cleaning.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eMulti-voltage input (10 to 30 V DC) for 12 V and 24 V electrical systems\u003c\/li\u003e\n\u003cli\u003eMagnetic mounting for quick placement on a ferrous metal surface\u003c\/li\u003e\n\u003cli\u003eUser-selectable warning patterns, including flashing and rotating\u003c\/li\u003e\n\u003cli\u003eAmber LED output under a clear polycarbonate dome for all-around warning visibility\u003c\/li\u003e\n\u003cli\u003eUp to 70 W draw, with polarity reversal protection\u003c\/li\u003e\n\u003cli\u003eIP6K9K and IP6K4K protection ratings for wet environments and aggressive washdowns\u003c\/li\u003e\n\u003cli\u003eOperating temperature range: -40°C to +65°C\u003c\/li\u003e\n\u003cli\u003eApproximate size: 400 mm long, 218 mm wide, about 49 mm tall\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eThe magnetic base works best on clean, flat steel. On many boats, common mounting spots include a steel deck plate, a work platform, a service vehicle carried aboard, or a dedicated steel pad installed where you need temporary warning coverage. If the surface is painted, dirty, or curved, take a moment to wipe it down so the magnet can sit flat.\u003c\/p\u003e\u003cp\u003ePlan the cable run so it will not get pinched by a hatch, door, or sliding track, and keep it clear of hot surfaces. In rough water, it is smart practice to add a secondary restraint so the unit stays aboard if the mounting surface flexes or takes an impact.\u003c\/p\u003e\u003ch6\u003eElectrical and system integration\u003c\/h6\u003e\u003cp\u003eThis lightbar operates across 10 to 30 V DC, which makes it a straightforward fit on both 12 V and 24 V boats. Current draw is about 6.1 A at 12 V and about 2.8 A at 24 V, so confirm your outlet or circuit can supply the load without nuisance trips.\u003c\/p\u003e\u003cp\u003ePolarity reversal protection helps guard against accidental reverse connection, but you should still wire and fuse it correctly for your boat. If you are using it in exposed areas, keep connections dry and supported so vibration does not work the wiring loose over time.\u003c\/p\u003e\u003ch6\u003eUse cases on board\u003c\/h6\u003e\u003cp\u003eThis style of amber warning lightbar is commonly used on workboats, commercial vessels, and support craft when crew are working on deck, handling tow gear, servicing equipment at night, or operating in low-visibility situations where an attention-getting warning signal helps nearby traffic understand that something is happening.\u003c\/p\u003e\u003cp\u003eIt is a good match for boaters who want a removable warning beacon they can move between tasks and locations without committing to a permanent mount, while still keeping compatibility with both 12 V and 24 V electrical systems.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eRinse the unit after saltwater exposure and avoid abrasive cleaners on the clear dome. If you store it between uses, keep the magnetic base free of grit so it does not scratch mounting surfaces and so it can sit flat the next time you deploy it.\u003c\/p\u003e","brand":"Hella Marine","offers":[{"title":"Default Title","offer_id":52269034963125,"sku":"QBP513299","price":281.52,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1298664_qbp513299.jpg?v=1771541535"},{"product_id":"qbp513307","title":"Hella Marine Mini Lightbar LED Warning Light Bar, Bracket Mount, 10-30V, Clear Lens, Amber LED, 360 Degree Signal, Flashing and Rotating, SAE J845 Class 1, IP6X, IPX4K, IPX9K, 500mm Cable","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Hella Marine 014565111 is a 16 inch LED mini lightbar that outputs an amber warning signal through a clear lens for on-board visibility in working and maneuvering situations.\u003c\/p\u003e\u003cp\u003eIt runs on 10 to 30 V DC for 12 V and 24 V systems, with a maximum power consumption of 70 W. The dome and housing are polycarbonate, and the unit carries IP67 and IP6K9K protection for spray, washdowns, and high-pressure cleaning.\u003c\/p\u003e\u003cp\u003eThis is a warning beacon style lightbar, not a deck or spreader light. It makes sense on boats where an amber signal is used for deck operations, towing support, dockside work, or other situations where you want to be noticed without adding white forward lighting.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eOperating voltage: 10 to 30 V DC (supports 12 V and 24 V systems)\u003c\/li\u003e\n\u003cli\u003eAmber warning signal with clear cover lens\u003c\/li\u003e\n\u003cli\u003eFlashing and rotating light functions with user-selectable patterns\u003c\/li\u003e\n\u003cli\u003eBracket mounting format with an overall footprint around 400 mm x 218 mm and a weight of about 1,300 g\u003c\/li\u003e\n\u003cli\u003eFixed version connection: 500 mm cable\u003c\/li\u003e\n\u003cli\u003eRated for IP67 and IP6K9K, with polarity reversal protection\u003c\/li\u003e\n\u003cli\u003eOperating temperature range: -40°C to +65°C\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eThe bracket mount is intended for a surface that stays flat and rigid, with a clear 360 degree view around the boat. Typical mounting points include a pilothouse roof, hardtop, or an equipment rack where antennas and rods will not block the signal.\u003c\/p\u003e\u003cp\u003ePlan wiring and switching around the load. Current draw is about 6.1 A on 12 V systems and 2.8 A on 24 V systems, so it is usually wired on a dedicated, fused circuit with a switch rated for the current.\u003c\/p\u003e\u003cp\u003eThe fixed-mount lead is 500 mm, so it helps to place a cable pass-through close to the mounting point. Keep any splices inside a protected enclosure and use marine-grade sealing practices so the connection stays dry.\u003c\/p\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eAt roughly 400 mm long and 218 mm wide, this lightbar fits well on center consoles, pilothouses, and utility craft where space is limited but a full-size beacon still matters. The temperature range supports cold-weather storage and hot decks in summer.\u003c\/p\u003e\u003ch6\u003eMaterials and care\u003c\/h6\u003e\u003cp\u003eThe dome and housing are polycarbonate. The bracket system uses stainless steel mounting brackets with foam foot cushions to help protect the mounting surface. During regular washdowns, rinse salt from the lens and mounting points and re-check fasteners so the light stays secure and the optics stay clear.\u003c\/p\u003e\u003ch6\u003eUse cases on board\u003c\/h6\u003e\u003cp\u003eThis lightbar is a good match for workboats, support craft, and larger tenders that need an amber warning signal during loading, towing, or dockside operations. It also fits charter, fishing, and dive boats that want a conspicuous signal during low-light deck work.\u003c\/p\u003e","brand":"Hella Marine","offers":[{"title":"Default Title","offer_id":52269034995893,"sku":"QBP513307","price":274.18,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1298665_qbp513307.jpg?v=1771541537"},{"product_id":"qbp513398","title":"Hella Marine Mini Lightbar LED Warning Light Bar, Magnetic Mount, 10-30V, 16 in, Amber Light, Clear Lens, Flashing and Rotating, IP6K9K, SAE J845 Class 1","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Hella Marine 014565121 is a 16 inch LED mini lightbar that puts out an amber warning signal on 10 to 30 VDC (12V or 24V) systems. It supports flashing and rotating patterns and is sealed to IP67 and IP6K9K for rain, spray, and washdowns.\u003c\/p\u003e\u003cp\u003eThis version uses a magnetic mount for temporary placement and a 10 ft cord with an inline switch and DC plug, so it can be moved between the dock, the truck, and the boat as needed. At full output it draws up to 6.1 A on a 12 V system (2.8 A on 24 V), so plan power and circuit protection accordingly.\u003c\/p\u003e\u003cp\u003eOn board, it is commonly used as a supplemental warning light during towing, docking assistance, deck work, or when a service craft needs to be seen clearly in the marina. It is not a substitute for required navigation lights; use it only when appropriate for local rules and operating conditions.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eAmber LED warning output with a clear polycarbonate dome for wide-angle visibility.\u003c\/li\u003e\n\u003cli\u003e10 to 30 VDC input to suit both 12V and 24V electrical systems.\u003c\/li\u003e\n\u003cli\u003eMultiple user-selectable patterns, including flashing and rotating modes.\u003c\/li\u003e\n\u003cli\u003eMagnetic mounting base for quick, temporary placement on a steel surface.\u003c\/li\u003e\n\u003cli\u003e10 ft power cord with inline switch and DC plug for a power outlet connection.\u003c\/li\u003e\n\u003cli\u003eIP67 and IP6K9K sealing to handle heavy spray, rain, and washdowns.\u003c\/li\u003e\n\u003cli\u003ePolarity reversal protection and an operating temperature range from -40 C to +65 C.\u003c\/li\u003e\n\u003cli\u003eEMC protection to ECE-R10 and CISPR 25 Class 3 to help reduce electrical noise issues.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eWhat’s included\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e16 inch LED mini lightbar with magnetic mount\u003c\/li\u003e\n\u003cli\u003e10 ft power cord with inline switch and DC plug\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis is a portable magnetic-mount lightbar, so it needs a flat steel surface for the magnets to hold properly. Many boats have stainless hardware and rails, but fiberglass and aluminum decks will not provide a magnetic surface on their own. If you plan to use it on a fiberglass or aluminum area, allow for a suitable steel mounting plate or another secure mounting approach.\u003c\/p\u003e\u003cp\u003eCheck clearance for the 16 inch length where you intend to place it so it does not interfere with lines, hatches, outriggers, antennas, or cockpit movement.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eSet the base down on a clean surface so the magnets seat fully, then route the cord so it cannot chafe or get pinched by hatches, doors, or seat bases. Leave enough slack for vibration and steering movement if used on a console area.\u003c\/p\u003e\u003cp\u003eKeep the unit and its magnets away from a magnetic compass and other sensitive instruments. A quick check before heading out can save a lot of confusion on the water.\u003c\/p\u003e\u003ch6\u003eElectrical and system integration\u003c\/h6\u003e\u003cp\u003ePower is 10 to 30 VDC, making it suitable for typical 12V and 24V onboard systems. Full-load draw is up to 6.1 A at 12 V (2.8 A at 24 V), so make sure the outlet and wiring feeding it are in good condition and protected by an appropriately rated circuit.\u003c\/p\u003e\u003cp\u003eIf you see interference on radios or electronics, increasing separation between the lightbar wiring and antenna coax, VHF wiring, or instrument harnesses often helps.\u003c\/p\u003e\u003ch6\u003eUse on board\u003c\/h6\u003e\u003cp\u003eThis setup is a good match for workboats, patrol and service craft, marina operations, and support boats that need a temporary amber warning signal during deck work, towing, or low-speed maneuvering in tight quarters. It is also handy for dockside tasks where visibility matters but you do not want a permanent install.\u003c\/p\u003e\u003cp\u003eUse it as a supplemental warning signal only, and avoid using it in a way that could be confused with required navigation lighting.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eRinse with fresh water after salt exposure and wipe down the polycarbonate dome to keep it clear. Avoid harsh solvents that can haze plastics over time.\u003c\/p\u003e\u003cp\u003ePeriodically inspect the cord, plug, and the magnet contact area for wear or grit so the unit sits flat and stays secure in vibration.\u003c\/p\u003e","brand":"Hella Marine","offers":[{"title":"Default Title","offer_id":52269035192501,"sku":"QBP513398","price":320.69,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1298666_qbp513398.jpg?v=1771541538"},{"product_id":"qbp513589","title":"Hella Marine 4-Pole Plug \u0026 Socket, Water-Resistant, Chrome-Plated Brass, Socket Cap, For 6.5mm Cable","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Hella Marine 002957801 is a 4-pole plug and socket deck connector for bringing four conductors through a deck or bulkhead and disconnecting them cleanly for service or removal. It is rated for a maximum load of 10A at 12V and uses chrome-plated brass housings with brass contacts for a connection that stands up well in a damp marine environment.\u003c\/p\u003e\u003cp\u003eThe socket is supplied with a protective cover for when the plug is not in place, and the plug is sized for cables up to 6.5 mm outer diameter. Wiring is via screw terminals, so you can land your conductors without special crimp pins and re-terminate later if your rigging changes.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e4-pole plug and socket set for four separate circuits through a deck or bulkhead pass-through\u003c\/li\u003e\n\u003cli\u003eMaximum load rating of 10A at 12V for typical onboard accessory circuits\u003c\/li\u003e\n\u003cli\u003eChrome-plated brass housings with brass contacts\u003c\/li\u003e\n\u003cli\u003eScrew terminal connections for straightforward installation and servicing\u003c\/li\u003e\n\u003cli\u003eProtective cover on the socket to help keep spray out when disconnected\u003c\/li\u003e\n\u003cli\u003ePlug accepts cable jackets up to 6.5 mm outer diameter\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eThis connector is commonly mounted where you need a tidy disconnect point, such as a transom, hardtop, deck edge, or mast base. Bed the socket properly and route wiring with a drip loop on the interior side so water cannot track along the conductors into the boat.\u003c\/p\u003e\u003cp\u003eLabel the four conductors before termination, tighten the screw terminals firmly, and add strain relief so vibration and cable movement are not carried by the terminals.\u003c\/p\u003e\u003ch6\u003eCompatibility and electrical use\u003c\/h6\u003e\u003cp\u003eUse it on 12V DC circuits up to the 10A maximum load rating. It suits lighting circuits, low-current accessories, and control wiring, rather than high-draw loads with large inrush currents.\u003c\/p\u003e\u003cp\u003eBefore ordering, confirm you need four conductors and that your cable jacket fits the 6.5 mm maximum outer diameter at the plug.\u003c\/p\u003e\u003ch6\u003eUse cases on board\u003c\/h6\u003e\u003cp\u003eIt is a solid fit for sailboats with a removable mast wiring harness, powerboats with detachable hardtops, and any installation where a light bar, deck wash, or accessory panel needs to unplug for service. It also works well for connections that are unplugged regularly, where keeping wiring organized matters.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eKeep the cover closed when the connector is not in use and rinse away salt after heavy exposure. If the connection ever feels gritty or intermittent, disconnect and clean the contacts before reassembling.\u003c\/p\u003e","brand":"Hella Marine","offers":[{"title":"Default Title","offer_id":52269035389109,"sku":"QBP513589","price":53.86,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1298667_qbp513589.jpg?v=1771541540"},{"product_id":"qbp482554","title":"Hella Marine LED Recess Strip Lamp, 12V, White LED, Wide Rim, 265mm","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Hella Marine 959073001 is a white LED recess strip courtesy lamp for 12V DC systems, built with a wide rim for a tidy flush finish. It draws under 2.0W (under 0.16A at 12V), so it can stay on for dockside or night moves without putting much load on the house bank.\u003c\/p\u003e\u003cp\u003eThis strip format is a practical fit for steps, toe-kicks, companionways, lockers, and other spots where you want light close to the deck. The lamp comes pre-wired with 2.5 m of cable, which helps when the nearest bus bar or switch panel is not right behind the mounting surface.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e12V DC white LED strip lamp with power draw under 2.0W (under 0.16A at 12V)\u003c\/li\u003e\n\u003cli\u003eTwo-hole recess mount with a wide rim and screw caps for a clean finished look\u003c\/li\u003e\n\u003cli\u003eMounting footprint: 265 mm overall length, 33 mm overall width, 237.5 mm mounting hole centres\u003c\/li\u003e\n\u003cli\u003eCut-out size: 217 mm x 20 mm, with about 29 mm clearance needed behind the panel\u003c\/li\u003e\n\u003cli\u003eIP6K7 and IP6K9K protection for dust, temporary immersion, and high-pressure washdowns\u003c\/li\u003e\n\u003cli\u003ePre-wired with 2.5 m cable and reverse polarity protection for easier installs\u003c\/li\u003e\n\u003cli\u003ePMMA lens material for resistance to UV exposure and common cleaning chemicals\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and fit\u003c\/h6\u003e\u003cp\u003ePlan the cut-out (217 mm x 20 mm) and confirm you have room behind the mounting surface for the lamp body (about 29 mm). The wide rim covers the edge of the cut-out, then the lamp secures with two screws on 237.5 mm centres. Avoid over-tightening the mounting screws into the lens area.\u003c\/p\u003e\u003ch6\u003eElectrical and wiring notes\u003c\/h6\u003e\u003cp\u003eThis lamp is polarity conscious. Connect the cable with the red stripe to positive (+) and the black cable to negative (-). Protect the circuit with a fuse rated at 2A maximum.\u003c\/p\u003e\u003cp\u003eLight output reduces as input voltage is lowered, which works well with analogue dimming approaches that drop DC input. For 12V installations, avoid continuous supply voltage above 16V.\u003c\/p\u003e\u003ch6\u003eOn-board use\u003c\/h6\u003e\u003cp\u003eThis style of strip lamp suits boats that need low-glare courtesy lighting along steps, under-gunwale storage, or around the cockpit and cabin where you want visibility without flooding the space with light. It is a good match for owners running long wire routes who still want a clean recessed install and sealed protection for wet areas.\u003c\/p\u003e\u003ch6\u003eWhat’s included\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e1 lamp with 2.5 m cable\u003c\/li\u003e\n\u003cli\u003e2 black stainless steel screws\u003c\/li\u003e\n\u003cli\u003e2 screw caps\u003c\/li\u003e\n\u003cli\u003e2 cable connectors\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Hella Marine","offers":[{"title":"Default Title","offer_id":52269049643189,"sku":"QBP482554","price":93.02,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1298412_qbp482554.jpg?v=1771541624"},{"product_id":"qbp482555","title":"Hella Marine 9073 LED Interior Lamp, 24V, 2W, 10 White LEDs, Crystal Clear Lens, Black Housing, 265mm Length, 2500mm Cable, Screw Connection","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Hella Marine 959073201 is a recessed LED courtesy strip lamp for 24V DC boats, using white LEDs behind a clear lens for clean step and walkway lighting. It draws about 2W and is sealed to IP6K7 and IP6K9K, so it holds up in lockers, companionways, cockpits, and other areas that see moisture and washdowns.\u003c\/p\u003e\u003cp\u003eThis is a two-hole recess mount light with a long, slim footprint (about 265 mm overall length) and a pre-wired 2.5 m cable to make routing back to a switch straightforward.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e24V DC, about 2W power draw for low electrical load\u003c\/li\u003e\n\u003cli\u003eIP6K7 and IP6K9K sealing for dust protection, temporary immersion, and high-pressure washdowns\u003c\/li\u003e\n\u003cli\u003eReverse polarity protection to help protect the light if wiring is accidentally swapped\u003c\/li\u003e\n\u003cli\u003eTwo-hole recess mount format with a slim bar shape (about 265 mm long and 33 mm wide)\u003c\/li\u003e\n\u003cli\u003eApprox. 237.5 mm mounting hole spacing center-to-center for layout checks before drilling\u003c\/li\u003e\n\u003cli\u003ePMMA lens material that stands up to UV exposure and common cleaning chemicals\u003c\/li\u003e\n\u003cli\u003ePre-wired with 2.5 m of cable to reduce the need for splices in damp areas\u003c\/li\u003e\n\u003cli\u003eRFCommSafe design to avoid interference with onboard communications and electronics\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and fit\u003c\/h6\u003e\u003cp\u003ePlan the mounting location so the light can sit flush and the back of the housing has room behind the panel. With an overall length of about 265 mm and hole spacing around 237.5 mm, it works well on steps, bulkheads, and under-seat faces where a long, low-profile light looks tidy. Allow roughly 25.5 mm of depth behind the mounting surface for the body.\u003c\/p\u003e\u003cp\u003eIn wet areas, keep the sealing surface clean and route the cable with a drip loop so water does not track into the wiring run. Use tinned marine-grade connections and support the cable so vibration does not work-harden the conductors over time.\u003c\/p\u003e\u003ch6\u003eElectrical and system integration\u003c\/h6\u003e\u003cp\u003eWire the lamp to a switched 24V DC circuit with appropriate circuit protection for the wire size and run length. Light output drops as input voltage is reduced below its operating voltage, which can be useful if your boat uses analogue voltage-reduction dimming on courtesy circuits.\u003c\/p\u003e\u003ch6\u003eUse on board\u003c\/h6\u003e\u003cp\u003eThis style of strip light is a good match for 24V cruising and commercial-style electrical systems where you want low-draw courtesy lighting that can handle routine washdowns. Common placements include companionway steps, cockpit footwells, engine room access steps, and storage lockers where you want light right where you are standing without taking up much space.\u003c\/p\u003e","brand":"Hella Marine","offers":[{"title":"Default Title","offer_id":52269049872565,"sku":"QBP482555","price":93.02,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1298414_qbp482555.jpg?v=1771541626"},{"product_id":"qbp482830","title":"Hella Marine MST3 LED Lighthead, Amber Light, 10-30V, Self-Adhesive Mount, Selectable Flash Patterns","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Hella Marine 358111001 is an amber LED navigation and signal light for 12 to 24V DC systems. It is typically used where an amber indication is required on board, such as special-purpose signaling, marking an operating area, or showing equipment status.\u003c\/p\u003e\u003cp\u003eAmber is not a standard port, starboard, stern, or anchor color, so it is usually fitted as an auxiliary light. Confirm the intended use for your vessel, then mount it where the lens stays visible and is not blocked by rails, rod holders, antennas, or canvas.\u003c\/p\u003e\u003cp\u003eThis is a good match for commercial and private boats that need a dedicated amber signal point and want a single light that works across both 12V and 24V electrical systems.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eAmber LED output for auxiliary signaling or marking on board\u003c\/li\u003e\n\u003cli\u003e12 to 24V DC input range for compatibility with common marine electrical systems\u003c\/li\u003e\n\u003cli\u003eLED light source with no filament to shake loose in a vibrating hull\u003c\/li\u003e\n\u003cli\u003eSuited to installations where you want a dedicated amber indication separate from red, green, or white navigation lights\u003c\/li\u003e\n\u003cli\u003eCommon fit for workboats, fishing boats, and utility setups that need an amber signal point during operations\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eChoose a mounting surface that stays rigid underway and gives the light a clear line of sight from the direction you need. Leave enough clearance to route the wiring without sharp bends, and plan for service access so the unit can be removed later without cutting the harness.\u003c\/p\u003e\u003cp\u003eConnect to a switched 12V or 24V DC circuit using tinned marine wire and sealed terminals. Protect the circuit with an appropriately sized fuse or breaker, keep splices above bilge level, and add chafe protection anywhere the wiring passes through fiberglass, aluminum, or bulkheads.\u003c\/p\u003e\u003ch6\u003eCompatibility and compliance\u003c\/h6\u003e\u003cp\u003eBefore treating this as a navigation-related light, confirm the color and placement rules that apply to your vessel and operating area. If your intent is general signaling or equipment indication, mount it where it is noticeable without creating glare at the helm.\u003c\/p\u003e\u003ch6\u003eOn-board use notes\u003c\/h6\u003e\u003cp\u003eAn amber signal light can be a useful visual cue during dockside work, night operations, and gear handling, especially when you want something that stands out from standard white deck lighting. It also suits operators who want clear status indication without adding another voltage-specific part to the boat.\u003c\/p\u003e","brand":"Hella Marine","offers":[{"title":"Default Title","offer_id":52269050003637,"sku":"QBP482830","price":68.54,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1298415_qbp482830.png?v=1771541628"},{"product_id":"qbp483027","title":"Hella Marine MST6E LED Lighthead, Blue Light, 12-24V, 21 Flash Patterns","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Hella Marine 358111701 is a surface-mount LED blue lighthead that runs on 11 to 30 VDC for use on both 12V and 24V electrical systems. It uses six 1W LEDs with an average power draw of about 5.5W and a listed maximum of 10.5W, which helps when you are planning loads on a small boat battery bank.\u003c\/p\u003e\u003cp\u003eThis is a low-profile lighthead intended for locations where you want a clean mount and dependable operation through vibration. It supports selectable flash patterns, stores the last-used pattern, and can be synchronized with additional units so multiple lightheads can flash together or alternate when wired for it.\u003c\/p\u003e\u003cp\u003eBlue lighting is often restricted to specific vessel types and operational uses. Confirm local requirements and onboard operating procedures before installing it as an externally visible signal light.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e11 to 30 VDC input for 12V and 24V systems\u003c\/li\u003e\n\u003cli\u003eBlue LED lighthead with selectable flash patterns and memory recall of the last-used setting\u003c\/li\u003e\n\u003cli\u003eSix 1W LEDs with average power around 5.5W and listed maximum power of 10.5W\u003c\/li\u003e\n\u003cli\u003eSynchronization support for multi-light installs (simultaneous or alternating flash behavior when wired accordingly)\u003c\/li\u003e\n\u003cli\u003eReverse polarity protection to help prevent damage from accidental wiring reversal\u003c\/li\u003e\n\u003cli\u003eWeatherproof and vibration resistant construction for exterior or interior mounting locations\u003c\/li\u003e\n\u003cli\u003eAluminum base to help shed heat when mounted to a solid surface\u003c\/li\u003e\n\u003cli\u003eWire leads included for power, ground, and pattern or sync control\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eMount the lighthead to a solid, flat area where the lens is not blocked by rails, canvas, or deck gear. On boats, choose a location that stays out of constant spray and direct impact, and route wiring so it is supported and protected from chafe. If you pass wiring through a bulkhead or hardtop, use a grommet and seal the opening so water cannot track along the cable into the structure.\u003c\/p\u003e\u003cp\u003eFor best results in saltwater environments, keep splices above the bilge and use marine-grade heat-shrink connections. Leave a small drip loop before the cable enters a console, cabin top, or junction box so water runs off instead of into the enclosure.\u003c\/p\u003e\u003ch6\u003eElectrical and system integration\u003c\/h6\u003e\u003cp\u003eThis lighthead is built for multi-voltage DC systems (11 to 30 VDC). Typical current draw is about 0.4A average at 12.8V and about 0.22A average at 24V, with listed maximum current of about 0.8A at 12.8V and about 0.44A at 24V. Plan circuit sizing and switch gear with those loads in mind.\u003c\/p\u003e\u003cp\u003eUse a dedicated, properly protected circuit and place a fuse close to the power source; a 3A fuse is a common match for this unit. Power and ground are handled through the primary leads, and the control lead is used for flash-pattern selection and synchronization when installing multiple lightheads.\u003c\/p\u003e\u003ch6\u003eUse cases on board\u003c\/h6\u003e\u003cp\u003eThis style of lighthead is commonly used as a compact warning or marker light on workboats, patrol and security craft, and support vessels that need a blue signal light while operating near docks, ramps, or in controlled areas. It can also be useful on trailers or shore-side support equipment that shares power with the vessel.\u003c\/p\u003e\u003cp\u003eIt is a good match for operators who want a low-profile blue lighthead that can be used across both 12V and 24V boats without adding voltage conversion hardware.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eRinse the lens and housing with fresh water after salt exposure and check the wiring exit point for strain or chafe. Periodically confirm mounting fasteners stay tight, especially on hardtops and other areas that see constant vibration.\u003c\/p\u003e","brand":"Hella Marine","offers":[{"title":"Default Title","offer_id":52269050167477,"sku":"QBP483027","price":78.34,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1298416_qbp483027.jpg?v=1771541629"},{"product_id":"qbp483055","title":"Hella Marine MST6E Mini LED Lighthead, 12-24V, White Light, 21 Flash Patterns, IP67, SAE J595 Class I","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Hella Marine 358111711 is a compact MST6E LED lighthead that runs on 12V and 24V DC systems and outputs white warning light in 21 selectable patterns, including steady-on.\u003c\/p\u003e\u003cp\u003eIt mounts as a low-profile lighthead with self-adhesive backing, and the 5.1 in (130 mm) length helps when space is limited on a hardtop, radar arch, equipment box, or transom area. The build is weatherproof and vibration resistant, and it carries SAE J595 Class 1 approval for warning-light applications.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e12V\/24V DC input for common onboard electrical systems\u003c\/li\u003e\n\u003cli\u003e21 user-selectable flash patterns, including steady-on\u003c\/li\u003e\n\u003cli\u003eSelf-adhesive backing for clean surface mounting\u003c\/li\u003e\n\u003cli\u003e5.1 in (130 mm) lighthead length for tight mounting locations\u003c\/li\u003e\n\u003cli\u003eFrosted lens that creates a glowing-body effect for better noticeability\u003c\/li\u003e\n\u003cli\u003eWeatherproof and vibration-resistant construction for exposed installs\u003c\/li\u003e\n\u003cli\u003eSAE J595 Class 1 approval for warning-light use\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003ePick a flat mounting spot where the light is easy to see and the wiring can be routed without chafe. For adhesive mounting to hold up long-term, clean and degrease the surface thoroughly, then press and hold per the tape’s requirements before putting the boat back into heavy spray or washdowns.\u003c\/p\u003e\u003cp\u003eWire it to a switched 12V or 24V DC feed using marine-grade connections and heat-shrink sealing, and protect the circuit with an appropriately sized fuse close to the power source. If you are installing multiple lightheads, the grouping function supports coordinated flashing, so it is worth planning your switching and control layout before you start pulling wire.\u003c\/p\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis lighthead is intended for DC systems found on most boats, including mixed fleets where some vessels are 12V and others are 24V. It is a warning-light style output and should not be treated as a replacement for required navigation lights; keep your COLREG and USCG-required running lights separate and compliant for your vessel class.\u003c\/p\u003e\u003ch6\u003eUse cases on board\u003c\/h6\u003e\u003cp\u003eThis style of lighthead is a practical add-on for workboats, tow or assist rigs, and fishing boats that need an attention-getting signal during dockside operations, restricted maneuvering, or deck work after dark. It is also a good match for skippers who want a compact auxiliary warning light that fits where a full beacon or larger fixture will not.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eRinse salt off with fresh water after runs, especially if the unit is mounted where it gets regular spray. Periodically inspect the wiring for strain, confirm the mounting surface remains secure, and avoid harsh solvents that can haze lenses or soften adhesives.\u003c\/p\u003e","brand":"Hella Marine","offers":[{"title":"Default Title","offer_id":52269050462389,"sku":"QBP483055","price":78.34,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1298417_qbp483055.jpg?v=1771541631"},{"product_id":"qbp483324","title":"Hella Marine MST6E Red LED Strobe Lighthead, 12-24V, Bolt-On Mount","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Hella Marine 358111721 is a red MST6E LED lighthead for 12-24V DC systems, built for surface mounting when you need a compact signal or warning light on a boat.\u003c\/p\u003e\u003cp\u003eThe housing sits low against the mounting surface and measures about 5.1 in long, 1.1 in tall, and 0.26 in thick, which helps when space is tight on a hardtop, cabin side, transom, trailer, or utility bracket. Six LEDs sit behind a frosted lens that lights across the face, with selectable flash patterns plus a steady-on mode for a constant red marker.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e12-24V DC operation for common boat electrical systems\u003c\/li\u003e\n\u003cli\u003eRed LED lighthead with a 6-LED layout\u003c\/li\u003e\n\u003cli\u003eLow profile body, roughly 5.1 in long, 1.1 in tall, and 0.26 in thick\u003c\/li\u003e\n\u003cli\u003eSelectable flash patterns, with a steady-on option\u003c\/li\u003e\n\u003cli\u003eSupports grouping and synchronization when multiple lightheads are installed\u003c\/li\u003e\n\u003cli\u003eReverse polarity protection to help prevent damage from accidental wiring mistakes\u003c\/li\u003e\n\u003cli\u003eMaximum power: 6W\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and wiring\u003c\/h6\u003e\u003cp\u003eMount it on a flat, solid surface where the light can be seen from the direction you need, then seal any fasteners and cable pass-throughs to keep water out of the laminate or core. Wire it to DC power and ground using marine-grade tinned conductors and heat-shrink terminations, and route the harness away from high-heat areas, sharp edges, and moving hardware.\u003c\/p\u003e\u003cp\u003eWhen multiple lightheads are fitted on the same vessel, they can be set up to flash together or alternate as a group so the pattern stays consistent.\u003c\/p\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis unit is intended for auxiliary signalling and attention lighting. If you are outfitting required navigation lighting, confirm the approvals, visibility range, and mounting angles that apply to your vessel and operating area.\u003c\/p\u003e\u003ch6\u003eOn-board use\u003c\/h6\u003e\u003cp\u003eIt suits workboats, tow and service craft, and anglers who want a small red light for low-speed operations, dockside loading, or marking equipment on deck at night without adding a bulky fixture.\u003c\/p\u003e","brand":"Hella Marine","offers":[{"title":"Default Title","offer_id":52269050790069,"sku":"QBP483324","price":78.34,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1298418_qbp483324.jpg?v=1771541632"},{"product_id":"qbp483338","title":"Hella Marine MST6E LED Warning Lighthead, 12-24V, Green","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Hella Marine 358111731 is a green LED lighthead for 12V and 24V DC systems, commonly used as an auxiliary signal or marker light on boats. It runs on a multi-voltage 11-30 VDC input range, which makes it a straightforward fit on most modern DC electrical systems.\u003c\/p\u003e\u003cp\u003eThis style of lighthead is used when you want a focused, attention-grabbing indicator rather than general area lighting. It supports selectable operating patterns, including a steady mode, and can be set up so multiple lightheads flash together or alternate when installed as a set.\u003c\/p\u003e\u003cp\u003eBecause this is a lighthead, treat it as an add-on signaling component. If you are shopping for required navigation lights, confirm your vessel’s running-light compliance separately and use a dedicated, approved navigation light assembly for that role.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eMulti-voltage input (11-30 VDC) for use on 12V and 24V battery systems\u003c\/li\u003e\n\u003cli\u003eGreen LED output for clear visual identification in low light and nighttime conditions\u003c\/li\u003e\n\u003cli\u003eSelectable operating patterns, including a steady setting, for different onboard signaling needs\u003c\/li\u003e\n\u003cli\u003eMulti-unit synchronization support when installing several heads on the same vessel\u003c\/li\u003e\n\u003cli\u003eReverse polarity protection to help prevent damage from accidental wiring mistakes\u003c\/li\u003e\n\u003cli\u003eHousing built for exterior mounting where spray, washdowns, and vibration are part of normal boat life\u003c\/li\u003e\n\u003cli\u003eAluminum base to help manage heat during extended operation\u003c\/li\u003e\n\u003cli\u003eLow-profile, surface-mount form factor that fits well on hardtops, cabin sides, arches, and transom structures\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003ePlan the mounting location the same way you would any exterior light on a boat: pick a flat, supported surface and leave room behind the panel for wiring bends, drip loops, and service access. On cored fiberglass, seal any penetrations properly so moisture cannot reach the core.\u003c\/p\u003e\u003cp\u003eWire it to a switched DC feed with appropriate circuit protection, and use marine-grade tinned copper wire with sealed connectors or adhesive-lined heat shrink. If you are installing multiple lightheads, keep runs tidy, label conductors, and route wiring away from sharp edges, steering linkages, and hot engine-room surfaces.\u003c\/p\u003e\u003ch6\u003eUse cases on board\u003c\/h6\u003e\u003cp\u003eThis lighthead is a good match for commercial-style boats, tow rigs, and anglers who want an extra visual indicator for deck activity, dockside operations, or low-speed work situations where being noticed matters. It is also useful on larger vessels where a row of synchronized lights is easier to see from different angles around the boat.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eRinse salt residue off with fresh water as part of routine washdowns, especially if the light is mounted where spray dries on the lens. Periodically inspect the mounting fasteners and wiring terminations for loosening or corrosion, and re-seal any disturbed penetrations during seasonal maintenance.\u003c\/p\u003e","brand":"Hella Marine","offers":[{"title":"Default Title","offer_id":52269051084981,"sku":"QBP483338","price":78.34,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1298419_qbp483338.jpg?v=1771541633"},{"product_id":"qbp483402","title":"Hella Marine MST6E LED Warning Lighthead, 12\/24V, Amber\/White Light, IP67, 21 Flash Patterns","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Hella Marine 358111741 is an MST6E mini LED lighthead that flashes amber and white warning light on 12\/24 VDC systems. It includes 21 selectable flash patterns, including steady on, so you can match the signal to the situation on board.\u003c\/p\u003e\u003cp\u003eOn a boat, this type of light is commonly used as an auxiliary attention light for dockside work, deck operations at night, towing and service tasks, or marking a temporary work zone where you want the crew and nearby traffic to notice you quickly.\u003c\/p\u003e\u003cp\u003eThis is a warning lighthead and it is not a replacement for required red, green, and white navigation lights.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eMulti-voltage input for 12\/24 VDC electrical systems\u003c\/li\u003e\n\u003cli\u003eAmber and white output from a single lighthead\u003c\/li\u003e\n\u003cli\u003e21 user-selectable flash patterns, including steady on\u003c\/li\u003e\n\u003cli\u003eSelf-adhesive backing for quick, simple surface mounting on a properly prepared substrate\u003c\/li\u003e\n\u003cli\u003eFrosted lens that spreads the light for broad visibility\u003c\/li\u003e\n\u003cli\u003eNon-volatile memory that retains the last selected pattern\u003c\/li\u003e\n\u003cli\u003eMultiple units can be grouped to flash together\u003c\/li\u003e\n\u003cli\u003eWeatherproof and vibration-resistant build for exposed mounting locations\u003c\/li\u003e\n\u003cli\u003eSAE J595 Class 1 approval\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eChoose a location where the light is visible but does not reflect into the helm at night, such as a hardtop face, radar arch, transom panel, or a service area on a work platform. Because the lighthead uses a self-adhesive backing, surface prep matters: clean, degrease, and dry the mounting area, then press firmly and allow time for the bond to set before heavy washdowns or sustained spray.\u003c\/p\u003e\u003ch6\u003eElectrical and system integration\u003c\/h6\u003e\u003cp\u003eConnect the lighthead to a switched DC feed on your 12V or 24V distribution and protect the circuit with a fuse or breaker sized for the wiring run. When installing multiple lightheads, route and secure the wiring so it is strain-relieved and supported, and plan the layout so grouped units remain visible from the angles you care about around the dock or on deck.\u003c\/p\u003e\u003ch6\u003eUse cases on board\u003c\/h6\u003e\u003cp\u003eThis lighthead is a good fit for commercial and service-style use on workboats, tenders, and utility craft, as well as for recreational owners who want an auxiliary warning signal for nighttime maintenance or busy marina conditions. It also suits mixed fleets where both 12V and 24V boats need the same style of warning light without changing hardware.\u003c\/p\u003e","brand":"Hella Marine","offers":[{"title":"Default Title","offer_id":52269051445429,"sku":"QBP483402","price":78.34,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1298420_qbp483402.jpg?v=1771541635"},{"product_id":"qbp483984","title":"Hella Marine Thru-Deck Cable Gland, Chrome Brass, Up to 8mm Cable","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Hella Marine 004208001 is a chrome plated brass deck gland for running a cable through a deck, hardtop, or cabin roof while keeping the entry point waterproof.\u003c\/p\u003e\u003cp\u003eIt is sized for a single cable up to 8 mm in diameter and keeps a low profile on deck, with an 18 mm overall height and a 32 mm base diameter. Use it anywhere you need a clean, sealed pass-through for wiring to spreader lights, deck lights, antennas, or other top-side accessories.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eWaterproof cable entry for a single cable up to 8 mm diameter\u003c\/li\u003e\n\u003cli\u003eChrome plated brass body for a bright finish that matches common deck hardware\u003c\/li\u003e\n\u003cli\u003eLow profile footprint: 18 mm high with a 32 mm base diameter\u003c\/li\u003e\n\u003cli\u003eTwo-screw flange style mount for securing the gland to the surface\u003c\/li\u003e\n\u003cli\u003eWorks with any onboard voltage since it is a mechanical pass-through, not an electrical connector\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eMeasure the outside diameter of the cable jacket, including any chafe sleeve or heat-shrink that needs to pass through the gland. If a molded plug or large connector is already on the cable, plan the routing so the largest section does not need to pass through the deck entry.\u003c\/p\u003e\u003cp\u003eCheck the 32 mm base diameter against the available flat mounting area, especially near curved cabin tops, handrails, or light brackets.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003ePick a location where water can shed away from the penetration and leave enough slack below deck to form a drip loop. Drill the cable pass-through and the mounting holes, then bed the flange with a marine sealant suited to your deck material and fasteners.\u003c\/p\u003e\u003cp\u003eAfter the cable is in place, snug the gland so it seals around the cable without crushing the jacket. On exposed runs, add chafe protection where the cable transitions into the deck and secure the cable below deck so vibration does not work the fitting loose over time.\u003c\/p\u003e\u003ch6\u003eUse on board\u003c\/h6\u003e\u003cp\u003eThis style of deck gland is a good match for clean top-side wiring on sailboats and powerboats where you want a neat cable entry for exterior lights and accessories. It also works well on cockpit coamings, hardtops, radar arches, and mast bases when keeping water out of the deck core and headliner matters.\u003c\/p\u003e","brand":"Hella Marine","offers":[{"title":"Default Title","offer_id":52269052068021,"sku":"QBP483984","price":12.24,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1298422_qbp483984.webp?v=1771541637"},{"product_id":"qbp484803","title":"Hella Marine 7-Pole Waterproof Plug \u0026 Socket Connector, Threaded, Sealing Cap, Up to 8 mm Cable OD, Silver-Plated Contacts, Impact-Resistant Plastic Housing","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Hella Marine 006807801 is a 7-pin waterproof plug and socket connection for extra-low voltage wiring on boats, giving you a clean disconnect point where equipment needs to be removable or a harness needs to pass through a panel. The connector is IP67-rated and uses a surface-mount socket with a threaded coupling so the plug stays locked in place when the boat is vibrating or taking spray.\u003c\/p\u003e\u003cp\u003eThis 7-pin version uses solder terminals and is typically paired with about 0.75 mm² conductors. It is rated up to 10A at 12V or 5A at 24V, which suits lighting, small accessory circuits, and multi-wire control runs rather than high-draw loads.\u003c\/p\u003e\u003cp\u003eThe housing is impact-resistant plastic with silver-plated contacts, and the socket includes a protective cap to keep the connection covered when unplugged.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e7-pole plug and socket connector with threaded coupling to help prevent accidental unplugging\u003c\/li\u003e\n\u003cli\u003eIP67 sealing for spray, washdowns, and brief submersion\u003c\/li\u003e\n\u003cli\u003eSurface-mount socket includes a protective cap to cover the contacts when disconnected\u003c\/li\u003e\n\u003cli\u003eImpact-resistant plastic housing with silver-plated contacts\u003c\/li\u003e\n\u003cli\u003e7-pin version uses solder terminals for secure wire attachment\u003c\/li\u003e\n\u003cli\u003eDesigned for cable jackets up to 8.0 mm diameter\u003c\/li\u003e\n\u003cli\u003eMaximum load up to 10A at 12V or 5A at 24V in extra-low voltage systems\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eMount the socket on a flat area with enough clearance behind the panel for wiring and strain relief. Use a proper marine sealant at the mounting surface if the location sees washdowns, then solder each conductor to the correct terminal and seal the connections with heat shrink where appropriate. Leave enough service loop so the plug can be connected and disconnected without pulling on the soldered joints.\u003c\/p\u003e\u003cp\u003eOnce connected, the threaded coupling keeps the plug seated, which is helpful on center consoles, cockpit panels, transoms, and other areas that see vibration.\u003c\/p\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis connector is meant for multi-circuit DC connections in extra-low voltage systems, not for shore power, inverters, or other AC wiring. Confirm you have seven conductors to carry, your cable jacket is within the 8.0 mm limit, and the circuit current stays within the 12V or 24V load rating.\u003c\/p\u003e\u003ch6\u003eUse cases on board\u003c\/h6\u003e\u003cp\u003eThis style of connector makes sense for removable deck or cockpit accessories, transom-mounted add-ons, or any install where you want to unplug a harness without opening junction boxes. It is a good match for boats that need a tidy, weatherproof disconnect for small accessory circuits that still have to survive salt spray and routine washdowns.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eKeep the cap on the socket whenever the plug is not connected. If the connector lives in an exposed area, a light wipe-down and an occasional check for salt buildup around the sealing surfaces helps the threads turn smoothly and keeps the connection easy to service.\u003c\/p\u003e","brand":"Hella Marine","offers":[{"title":"Default Title","offer_id":52269053313205,"sku":"QBP484803","price":80.78,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1298427_qbp484803.jpg?v=1771541642"},{"product_id":"qbp485340","title":"Hella Marine 2 Group Light Dimmer, For LED \u0026 Halogen Lamps, 8-30V DC, PWM, Soft-Start, Low Voltage Battery Protection","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Hella Marine 998572001 is a two-group light dimmer for 12V and 24V DC systems, with an 8 to 30 V DC input range.\u003c\/p\u003e\u003cp\u003eIt uses PWM dimming for one or two separate lighting groups, with a jumper that sets one-group mode (both outputs controlled together) or two-group mode (each output controlled independently). Each output is rated for up to 100W on a 12V system or 200W on a 24V system, and when both groups are combined into one the unit supports up to 200W at 12V or 400W at 24V.\u003c\/p\u003e\u003cp\u003eSoft-start and internal voltage regulation help protect filament and halogen bulbs when charging voltage climbs above nominal system voltage, and the built-in low-voltage protection shuts the lights off to reduce the chance of deep battery discharge.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e8 to 30 V DC input for use on 12V or 24V boats\u003c\/li\u003e\n\u003cli\u003eTwo dimming outputs with jumper-selectable one-group or two-group operation\u003c\/li\u003e\n\u003cli\u003eLoad capacity: 100W per output at 12V (200W total) or 200W per output at 24V (400W total)\u003c\/li\u003e\n\u003cli\u003ePWM dimming for compatible LED loads and for filament or halogen bulbs\u003c\/li\u003e\n\u003cli\u003eSoft-start to reduce start-up surge on halogen and help extend bulb life\u003c\/li\u003e\n\u003cli\u003eLow-voltage cutoff turns lights off below 9V (12V system) or 18V (24V system); re-enables when battery reaches 12V or 24V\u003c\/li\u003e\n\u003cli\u003eProtection and fusing: 2 x 10A fuses, plus overload and temperature protection\u003c\/li\u003e\n\u003cli\u003eCompact module size: 99 x 89 x 41 mm; weight 140 g\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eMount the module on a solid surface in a dry, ventilated location. The unit is controlled by momentary, normally-open pulse switches, and multiple switches can be wired in parallel per group when you want control from more than one location.\u003c\/p\u003e\u003cp\u003eSelect one-group or two-group operation by setting the onboard jumper. In either mode, plan your wiring so the lighting load is divided across the two outputs rather than piling everything onto one circuit.\u003c\/p\u003e\u003ch6\u003eElectrical and lighting compatibility\u003c\/h6\u003e\u003cp\u003eThis dimmer outputs PWM, so the connected lights need to be compatible with PWM dimming. With LED lighting, that usually means the lamp or driver accepts PWM input; if a fixture has an external driver, confirm the driver supports PWM to avoid flicker or limited dimming range.\u003c\/p\u003e\u003cp\u003eFor boats that still run filament or halogen bulbs, the soft-start function helps manage inrush current at switch-on, and the internal regulation helps keep the lighting circuit closer to nominal 12V or 24V when the alternator or charger is pushing the system higher.\u003c\/p\u003e\u003ch6\u003eUse on board\u003c\/h6\u003e\u003cp\u003eThis setup fits well when you want separate control of two zones such as cabin and cockpit, or saloon lighting and berth lighting, while keeping the switching simple with momentary push buttons. It also suits mixed refit jobs where some circuits are LED and others are still bulb-based, as long as the LED fixtures are PWM-dimmable.\u003c\/p\u003e","brand":"Hella Marine","offers":[{"title":"Default Title","offer_id":52269054230709,"sku":"QBP485340","price":205.63,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1298429_qbp485340.jpg?v=1771541645"},{"product_id":"qbp485818","title":"Hella Marine 4-Way Compact Toggle Switch Panel, 12V, 20A Switches, In-Line Spade Fuses, Splash Proof, White Housing","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Hella Marine 358114301 is a 4-way compact toggle switch panel for 12V DC boats, rated up to 20A with inline fuse holders and fuses mounted behind the panel. Each toggle is covered by a neoprene rubber boot, so it stays usable at an open helm where spray and routine washdowns happen.\u003c\/p\u003e\u003cp\u003eThe panel measures 95 x 107 x 55mm (H x W x D), which helps when dash space is tight or you are adding a small switch bank to a console, flybridge, or secondary control location. The white housing keeps the look clean and makes the circuit labels easy to read at a glance.\u003c\/p\u003e\u003cp\u003eThis style of panel is a solid fit for boats that need straightforward ON\/OFF control over common accessories like deck or cockpit lights, livewell pumps, washdown pumps, electronics power, or other 12V loads that belong on their own fused circuit.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eFour ON\/OFF toggle switches with neoprene rubber boots that help keep spray out\u003c\/li\u003e\n\u003cli\u003eRated up to 20A at 12V DC\u003c\/li\u003e\n\u003cli\u003eInline fuse holders and fuses located behind the panel for circuit protection\u003c\/li\u003e\n\u003cli\u003eCompact footprint: 95 x 107 x 55mm (H x W x D)\u003c\/li\u003e\n\u003cli\u003eImpact resistant plastic housing that holds up well in high vibration areas\u003c\/li\u003e\n\u003cli\u003eSupplied with a mounting gasket, screws, and a label set for identifying each circuit\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eWhat’s included\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e4-way switch panel\u003c\/li\u003e\n\u003cli\u003eMounting gasket\u003c\/li\u003e\n\u003cli\u003eMounting screws\u003c\/li\u003e\n\u003cli\u003eLabel set\u003c\/li\u003e\n\u003cli\u003eInline fuse holders and fuses (mounted behind the panel)\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003ePlan the mounting spot so you have rear access for wiring and for servicing the fuses. The 55mm depth is a helpful check before cutting or committing to a location, especially on center consoles with tight clearance behind the dash.\u003c\/p\u003e\u003cp\u003eThe included gasket is there to sit between the panel and the mounting surface. On boats that see frequent spray, taking the time to seat the gasket evenly and seal any cable pass-throughs nearby helps keep water where it belongs.\u003c\/p\u003e\u003ch6\u003eElectrical and system integration\u003c\/h6\u003e\u003cp\u003eThis panel is for 12V DC circuits. Size each fused circuit for the actual load and wiring run, and keep connections clean with tinned marine wire and sealed terminals where possible. If you are feeding higher draw loads, consider switching a relay from the panel and keeping the heavy current path short and properly protected.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eGive the toggle boots and rear connections a quick look as part of routine electrical checks. If the panel lives in an exposed spot, a fresh water rinse after salty runs helps, and keeping a few spare fuses onboard can save a trip when something pops mid-day.\u003c\/p\u003e\u003ch6\u003eUse cases on board\u003c\/h6\u003e\u003cp\u003eThis panel makes sense for smaller powerboats, fishing rigs, and sailboats that want four simple circuits grouped together without taking over the dash. It also works well as a secondary switch station where you need quick access to a handful of 12V accessories.\u003c\/p\u003e","brand":"Hella Marine","offers":[{"title":"Default Title","offer_id":52269054754997,"sku":"QBP485818","price":105.26,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1298431_qbp485818.png?v=1771541648"},{"product_id":"qbp486042","title":"Hella Marine 6-Way Compact Switch Panel, 12V, 20A, Inline Fuses","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Hella Marine 358114291 is a 6-way compact switch panel for 12V DC circuits, with a maximum load of 20A. It gives you six on\/off toggle switches in a two-row layout, which is a tidy way to group common helm and console accessories without taking up much space.\u003c\/p\u003e\u003cp\u003eThe face measures 95 x 107 mm and the panel depth is 55 mm, so it fits well on smaller dashes and side consoles where clearance matters. Each switch is protected by a neoprene rubber boot to handle spray, and the inline fuses sit behind the panel for circuit protection without adding separate fuse blocks for these six runs.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eSix on\/off toggle switches in a two-row layout for clean, easy labeling at the helm\u003c\/li\u003e\n\u003cli\u003eSplash-proof switch boots made from neoprene rubber for wet console conditions\u003c\/li\u003e\n\u003cli\u003eInline fuse holders with fuses located behind the panel for built-in circuit protection\u003c\/li\u003e\n\u003cli\u003eRated for 12V DC use with a maximum load of 20A\u003c\/li\u003e\n\u003cli\u003eCompact size: 95 x 107 x 55 mm (H x W x D) to suit tight mounting locations\u003c\/li\u003e\n\u003cli\u003eImpact-resistant plastic housing in a gray finish\u003c\/li\u003e\n\u003cli\u003eIncludes a label set plus gasket and mounting hardware to finish the install neatly\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eThis panel is typically installed at the helm, in a side console, or on an electrical switch pod where it stays within reach but out of direct washdown streams. The gasket helps the panel sit cleanly against the mounting surface, and the included template makes it easier to lay out the mounting and panel opening accurately.\u003c\/p\u003e\u003cp\u003ePlan for rear clearance so the wiring and fuse access stay serviceable after installation. Leave enough slack to pull the panel forward when you need to inspect or replace fuses.\u003c\/p\u003e\u003ch6\u003eElectrical and circuit planning\u003c\/h6\u003e\u003cp\u003eUse this panel on 12V DC systems and keep each circuit sized appropriately for the load and wiring run. High-draw gear that exceeds the panel rating should be switched through a relay or contactor, with the panel used as the control point.\u003c\/p\u003e\u003cp\u003eIt is a solid match for typical helm and utility loads such as navigation lights, cockpit or deck lights, electronics power feeds, pumps that fall within the rating, and other small onboard accessories where quick identification and fused protection matter.\u003c\/p\u003e\u003ch6\u003eWhat’s included\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e6-way compact switch panel (gray) with inline fuse holders and fuses\u003c\/li\u003e\n\u003cli\u003eLabel set\u003c\/li\u003e\n\u003cli\u003eMounting gasket\u003c\/li\u003e\n\u003cli\u003eMounting screws\u003c\/li\u003e\n\u003cli\u003eMounting template\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Hella Marine","offers":[{"title":"Default Title","offer_id":52269055082677,"sku":"QBP486042","price":117.5,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1298432_qbp486042.png?v=1771541649"},{"product_id":"qbp486237","title":"Hella Marine Mini ISO Relay, 12V, SPDT\/Form C, 40A NO\/20A NC, IP54, Resistor Coil Suppression, Mounting Bracket","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Hella Marine 933332181 is a 12V Mini ISO SPDT (Form C) relay with a mounting bracket for switching higher-current onboard circuits from a low-current switch or control output. It is rated for 40A continuous on the normally open contact and 20A continuous on the normally closed contact (at 85°C), with up to 150A inrush capacity for loads that hit hard at startup.\u003c\/p\u003e\u003cp\u003eThis relay uses a standard 5-terminal layout (30 common, 87 normally open, 87a normally closed, 85\/86 coil) with 6.3 x 0.8 mm blade terminals. The coil includes resistor suppression to help tame voltage spikes at turn-off, which is useful when the trigger side is coming from sensitive electronics.\u003c\/p\u003e\u003cp\u003eWith an IP54 rating and an operating range from -40°C to +85°C, it fits well behind a helm panel, in a dry locker, or inside an electrical enclosure where it is protected from direct washdown and bilge spray. It is a solid match for boats that need a clean way to control deck or spreader lights, horns, pumps, or other accessories without running full load current through a dash switch.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e12V nominal Mini ISO relay in SPDT (Form C) configuration with 5 terminals\u003c\/li\u003e\n\u003cli\u003eContinuous rating: 40A on N\/O contact and 20A on N\/C contact (at 85°C)\u003c\/li\u003e\n\u003cli\u003eHandles up to 150A inrush for high-startup loads\u003c\/li\u003e\n\u003cli\u003eIntegrated coil suppression resistor (560 ohm) for cleaner switching on the control side\u003c\/li\u003e\n\u003cli\u003eIP54-rated housing for locations exposed to dust and splashing water\u003c\/li\u003e\n\u003cli\u003e6.3 x 0.8 mm blade terminals (ISO 8092) for common relay sockets and crimp terminals\u003c\/li\u003e\n\u003cli\u003eMounting bracket for securing the relay to a bulkhead or panel inside an enclosure\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis relay is intended for 12V DC systems. It pulls in at 8.0V or less and drops out at 1.0V or higher, which helps it stay engaged during brief voltage dips. For resistive loads, use the continuous ratings as the main guide; for inductive loads like motors and solenoids, plan around the lower inductive switching ratings and always manage load-side kickback with appropriate suppression at the load.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eMount the relay by the bracket in a protected location and keep wiring supported so vibration does not work the terminals loose over time. Use properly crimped 6.3 mm female spade terminals or a matching Mini ISO relay socket, and protect the connection area from moisture and corrosion. Fuse the load circuit appropriately and keep high-current runs short to reduce voltage drop, especially when switching lighting where brightness matters.\u003c\/p\u003e\u003ch6\u003eElectrical and system integration\u003c\/h6\u003e\u003cp\u003eThe coil resistance is 73.8 ohm (plus or minus 10%), so the trigger side draws modest current and can be driven by many helm switches or control outputs when wired correctly. Switching time is fast (10 ms or less for operate and release), which is helpful when the relay is used as part of a control chain. Dielectric strength is rated to 1,000 VDC.\u003c\/p\u003e\u003ch6\u003eUse cases on board\u003c\/h6\u003e\u003cp\u003eThis relay is commonly used to let a small dash switch control a high-current accessory circuit. Typical placements are behind the helm, in a flybridge console, or inside a protected electrical locker close to the load feed for deck and spreader lighting circuits.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003ePeriodically check that terminals stay tight, clean, and free of heat discoloration, especially on high-load circuits. In saltwater environments, keeping the relay inside a covered enclosure and protecting the terminals with corrosion control practices can go a long way toward preventing intermittent faults.\u003c\/p\u003e","brand":"Hella Marine","offers":[{"title":"Default Title","offer_id":52269055410357,"sku":"QBP486237","price":12.24,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1298433_qbp486237.jpg?v=1771541651"},{"product_id":"qbp486288","title":"Hella Marine SPDT Mini Relay, 12V, 20\/40A, 5-Pin, Dust Cover","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Hella Marine 933332051 is a 12V Mini ISO changeover relay (SPDT\/Form C) rated for 40A continuous on the normally open circuit and 20A on the normally closed circuit at 85°C.\u003c\/p\u003e\u003cp\u003eIt is a straightforward way to switch higher-current accessories without running full load current through a small helm switch. On board, that often means deck and spreader lights, horns, washdown pumps, or other loads where keeping voltage drop down matters.\u003c\/p\u003e\u003cp\u003eThe relay uses five 6.3 mm blade terminals in the standard 30\/87\/87a (load) and 85\/86 (coil) layout, and it includes a dust cover with an IP54 rating for basic splash and dust protection.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e12V nominal coil with max coil voltage of 20V\u003c\/li\u003e\n\u003cli\u003eSPDT\/Form C contacts with 40A continuous rating on N\/O and 20A on N\/C (at 85°C)\u003c\/li\u003e\n\u003cli\u003eMax inrush load rated to 150A for short startup surges\u003c\/li\u003e\n\u003cli\u003eOperate time = 10 ms and release time = 5 ms\u003c\/li\u003e\n\u003cli\u003eAmbient temperature range -40°C to +85°C\u003c\/li\u003e\n\u003cli\u003eMini ISO footprint with 6.3 mm blade terminals for common 5-pin relay sockets\u003c\/li\u003e\n\u003cli\u003eIP54 dust cover to help keep spray and debris off the terminals in sheltered mounting spots\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eMount the relay in a dry, protected area such as behind the dash, inside a console, or in a covered locker. Use a properly sized fuse or breaker on the feed to terminal 30, and keep the high-current run as short as practical between the power source, relay, and load.\u003c\/p\u003e\u003cp\u003eTerminal 87 is the normally open output, and 87a is the normally closed output. Terminals 85 and 86 are the coil connections that can be switched by a low-current control circuit.\u003c\/p\u003e\u003cp\u003eThis relay has no built-in coil suppression, so if the trigger circuit is connected to sensitive electronics, add the suppression method your system requires.\u003c\/p\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis is a 12V relay, so it matches 12V DC boats and accessories. It uses the standard 5-terminal Mini ISO\/SPDT layout with 6.3 mm blades, which keeps it compatible with many off-the-shelf relay bases and harness sockets. For longevity, avoid mounting locations that see regular washdowns or bilge water.\u003c\/p\u003e\u003ch6\u003eUse on board\u003c\/h6\u003e\u003cp\u003eIt suits boats where a small switch or control output needs to command a heavier load, like spreader lights on a mast, deck floods on a hardtop, or an accessory circuit that you want switched from a protected control point. It is a practical fit when you need a changeover relay with a 40A normally open rating on a 12V system.\u003c\/p\u003e","brand":"Hella Marine","offers":[{"title":"Default Title","offer_id":52269055705269,"sku":"QBP486288","price":12.24,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1298434_qbp486288.jpg?v=1771541652"}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/collections\/1278943_hella-marine.webp?v=1768106186","url":"https:\/\/www.qualityboatparts.com\/collections\/hella-marine.oembed?page=7","provider":"Quality Boat Parts","version":"1.0","type":"link"}