{"title":"Fuel Line Connectors","description":"","products":[{"product_id":"qbp558128","title":"Attwood Marine Fuel Line Kit, For Yamaha Engines and Tanks, 3\/8 in x 6 ft, Low-Permeation Primer Bulb","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Attwood Marine 93806YLP7 is a Yamaha fuel line kit with a 3\/8 in. inside diameter hose, a 6 ft run, and a multi-layer low-permeation primer bulb. It is built for Yamaha engine and tank connections, so it works as a replacement when the existing setup uses this hose size and matching Yamaha ends.\u003c\/p\u003e\u003cp\u003eThe hose is fiber reinforced, made for ethanol-blended fuels, and rated up to 100 C and 600 psi. Stepless 360 degree stainless steel clamps and engineered hose barbs support pressurized fuel systems. A separate tank fitting and fuel demand valve are not included, which matters if your current rig depends on those parts.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e3\/8 in. inside diameter fuel hose in a 6 ft assembly for Yamaha engine and tank connections\u003c\/li\u003e\n\u003cli\u003eMulti-layer low-permeation primer bulb helps keep the fuel system primed while reducing fuel vapor loss\u003c\/li\u003e\n\u003cli\u003eFiber-reinforced hose is rated up to 100 C and 600 psi\u003c\/li\u003e\n\u003cli\u003eHose construction helps resist kinking and hardening when used with ethanol-blended fuels\u003c\/li\u003e\n\u003cli\u003eStepless 360 degree stainless steel clamps and engineered hose barbs are built for pressurized fuel systems\u003c\/li\u003e\n\u003cli\u003eIncludes two 8896LP6 hose fittings for the engine end and tank end\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis assembly is sized for 3\/8 in. fuel hose and Yamaha engine connections. Before ordering, check the inside diameter on your current line and confirm whether your tank side already has the fitting you need, because the kit does not include a separate tank fitting.\u003c\/p\u003e\u003cp\u003eThe 6 ft hose length suits many outboard layouts where the tank sits fairly close to the motor. On boats with a longer path from tank to engine, it is worth measuring the full route with the motor turned side to side so the hose does not pull tight or rub on corners and rigging points.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eThis kit is a sensible replacement when the old hose has gone stiff, the bulb no longer holds prime, or the end fittings have started to wear. It is also a good match for owners updating older fuel hose on Yamaha outboards and wanting a low-permeation line that handles ethanol-blended fuel without the hose hardening as quickly.\u003c\/p\u003e\u003cp\u003eFor day boats, skiffs, small center consoles, and similar outboard setups, the assembly covers the core pieces most owners replace first: hose, bulb, and hose-end fittings. If your system uses a fuel demand valve or a specific tank fitting, those parts need to stay in place or be matched separately.\u003c\/p\u003e\u003ch6\u003eWhat’s included\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e6 ft fuel hose with 3\/8 in. inside diameter\u003c\/li\u003e\n\u003cli\u003eMulti-layer low-permeation primer bulb\u003c\/li\u003e\n\u003cli\u003eTwo 8896LP6 hose fittings for the engine end and tank end\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Attwood Marine","offers":[{"title":"Default Title","offer_id":52023533109429,"sku":"QBP558128","price":64.99,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1329592_qbp558128.webp?v=1780191863"},{"product_id":"qbp798539","title":"Attwood Marine Universal Sprayless Fuel Line Connector, Check Valves","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Attwood Marine Universal Sprayless Connector is a fuel-line connector family made to reduce fuel spray when connecting or disconnecting pressurized marine fuel hoses during fueling or maintenance.\u003c\/p\u003e\u003cp\u003eThis system replaces traditional fuel tank fittings and uses integrated check valves that close when the connector is disconnected. The hose male and hose female fittings work with 5\/16\" and 3\/8\" fuel lines, while the tank male fitting fits standard 1\/4\" NPT tank connections and includes pre-applied fuel-grade thread sealant.\u003c\/p\u003e\u003cp\u003eIt is a practical upgrade for outboard fuel systems where cleaner hose changes, less deck cleanup, and controlled fuel handling matter. The fittings are compatible with ethanol blended fuels and OEM-brand engines, with a high-flow design rated at less than .25kPa restriction at 50 liters per hour.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eSprayless connector design helps prevent fuel spray when pressurized fuel hoses are connected or disconnected.\u003c\/li\u003e\n\u003cli\u003eIntegrated check valves close on disconnect to help control fuel flow during fueling and maintenance.\u003c\/li\u003e\n\u003cli\u003eHose male and hose female fittings are compatible with both 5\/16\" and 3\/8\" fuel lines.\u003c\/li\u003e\n\u003cli\u003eTank male fitting fits standard 1\/4\" NPT fuel tank outlets and uses pre-applied fuel-grade thread sealant.\u003c\/li\u003e\n\u003cli\u003eHigh-flow fitting design has less than .25kPa restriction at 50 liters per hour.\u003c\/li\u003e\n\u003cli\u003eCompatible with ethanol blended fuels and OEM-brand marine engines.\u003c\/li\u003e\n\u003cli\u003eEPA Certified and CARB Approved for applicable marine fuel system use.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eVariants\u003c\/h6\u003e\u003cp\u003eThe Universal Sprayless Connector range is offered in four configurations that cover common hose-end, tank-end, and combined connection needs in a portable or fixed marine fuel system.\u003c\/p\u003e\u003cp\u003eThe main differences are the connector interface and where the fitting is installed in the fuel line. The sprayless connection function and check-valve behavior are consistent across the male and female connector styles.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e8838HF6: Hose female connector. This version fits the hose side of the system and works with 5\/16\" and 3\/8\" fuel lines.\u003c\/li\u003e\n\u003cli\u003e8838HM6: Hose male connector. This version is used where a male hose connection is needed on 5\/16\" or 3\/8\" ID fuel hose.\u003c\/li\u003e\n\u003cli\u003e8838TM6: Tank male connector. This version fits standard 1\/4\" NPT fuel tank outlets and includes pre-applied fuel-grade thread sealant for the threaded connection.\u003c\/li\u003e\n\u003cli\u003e8838US6: Male and female connector set. This configuration pairs the tank-side male connector with the hose-side female connector for a matched sprayless connection.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and fit\u003c\/h6\u003e\u003cp\u003eMatch the fitting style to the point in the fuel system being updated: hose female or hose male for the fuel hose, tank male for the fuel tank outlet, or the male and female set when both ends of the connection are being replaced together.\u003c\/p\u003e\u003cp\u003eFor hose installations, confirm that the fuel line is 5\/16\" or 3\/8\" before ordering. For tank installations, confirm a standard 1\/4\" NPT outlet. As with any fuel-system work, install with the system depressurized, check the routing for chafe points, and inspect the connection for leaks before running the engine.\u003c\/p\u003e\u003ch6\u003eUse cases on board\u003c\/h6\u003e\u003cp\u003eThis connector family is a good match for trailer boats, fishing boats, tenders, and other outboard-powered vessels where portable tanks or serviceable fuel hose connections are handled often. It is especially useful when fuel hoses are disconnected during storage, tank changes, dockside maintenance, or pre-trip checks.\u003c\/p\u003e","brand":"Attwood Marine","offers":[{"title":"Hose Female","offer_id":52023557980341,"sku":"QBP798539-V7","price":13.45,"currency_code":"USD","in_stock":true},{"title":"Hose Male","offer_id":52023558013109,"sku":"QBP798539-V0","price":17.12,"currency_code":"USD","in_stock":false},{"title":"Tank Male","offer_id":52023558045877,"sku":"QBP798539-V5","price":13.45,"currency_code":"USD","in_stock":false},{"title":"Male\/Female","offer_id":52023558078645,"sku":"QBP798539-V9","price":24.62,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1332520_qbp798539.webp?v=1780191874"},{"product_id":"qbp988621","title":"Attwood Marine Fuel Tank Fitting, For Yamaha, 1\/4 in NPT Male, Brass","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Attwood Marine 8897-6 is a tank-side fuel fitting for Yamaha portable fuel tank connections with a 1\/4 inch male NPT thread. It is made from solid machined brass and is built for gasoline fuel systems that may see leaded, unleaded, ethanol-blended, or alcohol-blended fuels.\u003c\/p\u003e\u003cp\u003eThis fitting connects at the tank, not at the engine or hose end, so it is the part to check when you are replacing a worn tank connector or matching a new hose assembly to an existing Yamaha-style tank outlet. It also fits some Mercury and Mariner applications that use the same connection pattern.\u003c\/p\u003e\u003cp\u003eFor hose-side connection, it mates with Attwood 8896LP6 and 88FHY516-6 fittings. That makes it a straightforward replacement when you want to keep the same tank layout and restore a secure quick-connect point between the portable tank and fuel line.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e1\/4 inch male NPT tank thread for Yamaha-style portable fuel tank connections\u003c\/li\u003e\n\u003cli\u003eSolid machined brass body that stands up well to fuel exposure in a marine setting\u003c\/li\u003e\n\u003cli\u003eWorks with leaded, unleaded, ethanol-blended, and alcohol-blended fuels\u003c\/li\u003e\n\u003cli\u003eTank-side quick-connect fitting that mates with Attwood 8896LP6 and 88FHY516-6 hose fittings\u003c\/li\u003e\n\u003cli\u003eAlso used on select Mercury and Mariner setups that share the Yamaha-style connector pattern\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis part is a good match when the tank has a female 1\/4 inch NPT port and the fuel line uses a Yamaha-style quick-connect at the tank. It is not a universal fuel connector, so the thread style and the quick-connect pattern both need to match before installation.\u003c\/p\u003e\u003cp\u003eOn older boats and portable tank setups, the quickest fit check is to confirm the tank-side thread size and compare the coupler style on the hose assembly. If your hose already uses the matching Attwood Yamaha-style fitting, this connector keeps the system consistent without changing the rest of the fuel line.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eBecause this is an NPT threaded fitting, the thread seal should be made with a fuel-safe sealant suited to marine fuel systems. The brass body is compact enough for typical portable tank installations, but the connection still needs enough clearance for the hose coupler to snap on and release cleanly.\u003c\/p\u003e\u003cp\u003eThis fitting makes sense for boaters replacing a corroded or leaking tank connector on a portable outboard fuel setup. It is especially relevant on small fishing boats, tenders, and other outboard-powered boats that rely on removable fuel tanks and quick-connect fuel lines.\u003c\/p\u003e","brand":"Attwood Marine","offers":[{"title":"Default Title","offer_id":52023561846965,"sku":"QBP988621","price":10.04,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1329579_qbp988621.webp?v=1780191882"},{"product_id":"qbp738247","title":"Attwood Marine Mercury Twist-Lock Female Fuel Tank Fitting, 1\/4 in NPT, 90 Degree Elbow, Nylon","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Attwood Marine 8882-6 is a Mercury\/Mariner twist-lock female tank fitting for the tank end of a fuel line. It uses a 1\/4-inch NPT threaded connection, a nylon body, and a 90-degree elbow in a 2-piece layout that helps when space around the tank outlet is limited.\u003c\/p\u003e\u003cp\u003eThis fitting is used on the tank side of a Mercury\/Mariner fuel line assembly and mates with Attwood 14532-6. It is also suitable for leaded, unleaded, ethanol-blended, and alcohol-blended fuels, which is useful on boats that see different fuel blends through the season.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eMercury\/Mariner twist-lock female fitting for the tank side of the fuel line\u003c\/li\u003e\n\u003cli\u003e1\/4-inch NPT threaded connection for tanks that use a standard threaded port\u003c\/li\u003e\n\u003cli\u003e90-degree elbow helps route the fuel line where a straight fitting would crowd the hose\u003c\/li\u003e\n\u003cli\u003e2-piece construction\u003c\/li\u003e\n\u003cli\u003eNylon material construction\u003c\/li\u003e\n\u003cli\u003eMates with Attwood 14532-6\u003c\/li\u003e\n\u003cli\u003eSuitable for leaded, unleaded, ethanol-blended, and alcohol-blended fuels\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis part belongs on Mercury\/Mariner twist-lock fuel systems and is intended for the tank side, not the engine side. Before ordering, check the connector style and confirm that your tank port is 1\/4-inch NPT. If your setup uses a different connector family or a hose barb instead of a threaded tank port, this fitting will not match.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eThe 90-degree elbow is useful where the outlet sits close to a tank handle, transom wall, or splashwell and the hose needs to turn cleanly without a hard bend. Apply thread sealant to the NPT threads during installation and orient the elbow so the fuel line leaves the tank without kinking or rubbing.\u003c\/p\u003e\u003cp\u003eThis fitting is a good match for boats that run a Mercury\/Mariner outboard and use a twist-lock tank connection. It also works well as a replacement when the existing tank fitting is worn, leaks at the connection point, or no longer locks onto the hose fitting cleanly.\u003c\/p\u003e","brand":"Attwood Marine","offers":[{"title":"Default Title","offer_id":52023577772213,"sku":"QBP738247","price":14.99,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1329644_qbp738247.webp?v=1780191912"},{"product_id":"qbp824885","title":"Brp Gas Tank Connector (772681)","description":"\u003cp\u003eThe 772681 GAS TANK CONNECTOR is a machine brass fitting with 1\/4 inch NPT threads and an O-ring for increased resistance to reformulated fuels and alcohol. The Viton O-ring protects petroleum equipment against petrochemicals and other hazardous pollutants. The connection has a wide range of uses.\u003c\/p\u003e \u003cp\u003eFits:\u003c\/p\u003e \u003cul\u003e \u003cli\u003eEvinrude\u003c\/li\u003e \u003c\/ul\u003e \u003cp\u003e15 PORTABLE 2012\u003c\/p\u003e \u003cp\u003e35 2000 - 2001\u003c\/p\u003e \u003cp\u003e40 2000 - 2012\u003c\/p\u003e \u003cp\u003e50 2012\u003c\/p\u003e \u003cp\u003e55 2000\u003c\/p\u003e \u003cp\u003e60 2012\u003c\/p\u003e \u003cp\u003e65 2012\u003c\/p\u003e \u003cp\u003e6 PORTABLE 2012\u003c\/p\u003e \u003cp\u003e9.8 PORTABLE 2012\u003c\/p\u003e \u003cp\u003eAA 15 PORTABLE AA\u003c\/p\u003e \u003cp\u003eAA 6 PORTABLE AA\u003c\/p\u003e \u003cp\u003eAA 9.8 PORTABLE AA\u003c\/p\u003e \u003cp\u003eAB 15 PORTABLE AB\u003c\/p\u003e \u003cp\u003eAB 6 PORTABLE AB\u003c\/p\u003e \u003cp\u003eAB 9.8 PORTABLE AB\u003c\/p\u003e \u003cp\u003eAF 9.8 PORTABLE AF\u003c\/p\u003e \u003cul\u003e \u003cli\u003eJohnson\u003c\/li\u003e \u003c\/ul\u003e \u003cp\u003e25 2000 - 2006\u003c\/p\u003e \u003cp\u003e35 2000 - 2001\u003c\/p\u003e \u003cp\u003e40 2000 - 2005\u003c\/p\u003e \u003cp\u003e50 2000 - 2005\u003c\/p\u003e \u003cp\u003e55 2000 - 2005\u003c\/p\u003e \u003cp\u003e55 COMMERCIAL 2003\u003c\/p\u003e \u003cp\u003eRigging Accessories 2005-2010\u003c\/p\u003e \u003cp\u003eKey features:\u003c\/p\u003e \u003cul\u003e \u003cli\u003eMachine brass with 1\/4 inch NPT thread\u003c\/li\u003e \u003cli\u003eThe Viton O-ring provides increased resistance to reformulated fuels and alcohol.\u003c\/li\u003e \u003c\/ul\u003e \u003cp\u003eSpecifications:\u003c\/p\u003e \u003cul\u003e \u003cli\u003eSKU: 772681\u003c\/li\u003e \u003cli\u003eUPC: 745419247683\u003c\/li\u003e \u003cli\u003eWeight: 0.15 LBS\u003c\/li\u003e \u003cli\u003eAlternate Products SKU: \"033400-10\", \"18-8056\", \"775640\", \"033410-10\", \"22-00819\"\u003c\/li\u003e \u003cli\u003eManufacturer Part Number (MPN): 772681\u003c\/li\u003e \u003cli\u003eThis product replaces: BRP772681, 745419247683, 772681, 177007, BRP177007, BRP502867\u003c\/li\u003e \u003cli\u003eDimensions: 1.75” x 1”5.5”\u003c\/li\u003e \u003cli\u003eBrand: Bombardier Recreational Products (BRP)\u003c\/li\u003e \u003cli\u003eManufacturer: Bombardier Recreational Products (BRP)\u003c\/li\u003e \u003c\/ul\u003e \u003ch4\u003eThis product replaces:\u003c\/h4\u003e \u003cul\u003e \u003cli\u003eBRP772681, 745419247683, 772681, 177007, BRP177007, BRP502867\u003c\/li\u003e \u003c\/ul\u003e","brand":"BRP","offers":[{"title":"Default Title","offer_id":52023941398709,"sku":"QBP824885","price":11.75,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1234646_qbp824885.jpg?v=1763261234"},{"product_id":"qbp101835","title":"Brp Fuel Connector - Brp (775640)","description":"\u003cp\u003eSafety should always come first for boaters. A yacht fuel leak is a very harsh situation. Numerous horrible things may occur if a fuel leak gets out of control. It even sets on fire! It is best to carefully verify the connections before attaching the fuel line to the boat, as a result. Another consideration is the engine's lifespan since correct fuel line installation will help to guarantee that the engine consumes fuel as it should. With this BRP Fuel Connector, you may alter their gasoline line assemblies to match the current connectors on their fuel tanks! All fittings are made under OEM specifications and have an o-ring seal to provide a secure connection.\u003c\/p\u003e \u003cp\u003eKey Features:\u003c\/p\u003e \u003cul\u003e \u003cli\u003eIt connects to the fuel hose on the engine or fuel tank side.\u003c\/li\u003e \u003cli\u003eTank Connector and Fuel Line Engine Barb Female.\u003c\/li\u003e \u003cli\u003eThe O-ring structure ensures secure connections without leaks.\u003c\/li\u003e \u003cli\u003eViton gaskets are used with brass and stainless steel components to strengthen their resistance to ethanol fuels.\u003c\/li\u003e \u003cli\u003eFuel line connections from Scepter are ideal for ensuring a faultless tank-to-engine experience.\u003c\/li\u003e \u003cli\u003eTwo-prong, metal-clipped OEM-compatible tank to engine connector (BRP Johnson\/Evinrude).\u003c\/li\u003e \u003c\/ul\u003e \u003cp\u003eProduct Details:\u003c\/p\u003e \u003cul\u003e \u003cli\u003eSKU: 775640\u003c\/li\u003e \u003cli\u003eUPC: 745419285357\u003c\/li\u003e \u003cli\u003eWeight: 0.03 LBS\u003c\/li\u003e \u003cli\u003eUnit Of Measure: EA\u003c\/li\u003e \u003c\/ul\u003e \u003cbr\u003e\u003cbr\u003e \u003ch4\u003eThis product replaces:\u003c\/h4\u003e \u003cul\u003e \u003cli\u003eBRP775640\u003c\/li\u003e \u003cli\u003e745419285357\u003c\/li\u003e \u003cli\u003e777346\u003c\/li\u003e \u003cli\u003e775640\u003c\/li\u003e \u003cli\u003e176745\u003c\/li\u003e \u003cli\u003e174508\u003c\/li\u003e \u003cli\u003eBRP176745\u003c\/li\u003e \u003c\/ul\u003e","brand":"BRP","offers":[{"title":"Default Title","offer_id":52023941529781,"sku":"QBP101835","price":8.75,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1234652_qbp101835.jpg?v=1763261237"},{"product_id":"qbp158829","title":"Volvo Penta Fuel Pipe Volvo Penta - Volvo Penta (3860211)","description":"\u003cp\u003eVolvo Penta Exploded view \/ schematic Fuel Pump\u003c\/p\u003e","brand":"Volvo Penta","offers":[{"title":"Default Title","offer_id":52024137023669,"sku":"QBP158829","price":145.91,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1248615_qbp158829.jpg?v=1763265697"},{"product_id":"qbp851921","title":"Brp Fuel Connector - Brp (351399)","description":"\u003ch4\u003eThis product replaces:\u003c\/h4\u003e \u003cul\u003e \u003cli\u003eBRP351399\u003c\/li\u003e \u003c\/ul\u003e","brand":"BRP","offers":[{"title":"Default Title","offer_id":52024167628981,"sku":"QBP851921","price":6.09,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1250809_qbp851921.jpg?v=1763266429"},{"product_id":"qbp813005","title":"Garmin GFS 10 Fuel Flow Sensor, For Gasoline Engines, NMEA 2000\/CANet, 3\/8 in, 2-50 GPH, Fuel Level Sensing","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Garmin 010-00671-00 is an in-line fuel sensor that tracks gasoline fuel flow and can also read tank level when wired to an existing fuel gauge or resistive tank level sender. It communicates with compatible displays over NMEA 2000 or Garmin CANet and supports flow rates from 2 to 50 gal\/hr (7.5 to 190 L\/h).\u003c\/p\u003e\u003cp\u003eThis sensor installs into a 3\/8 in. (9.5 mm) fuel hose and should be mounted to the boat, not directly on the engine. It runs on 10 to 22 Vdc, uses a 0.25 A fuse, and has a unit size of 2 1\/8 in. (54 mm) W x 3 21\/32 in. (93 mm) H x 1 1\/4 in. (32 mm) D.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eOutputs fuel flow and fuel-used data to compatible chartplotters and instruments via NMEA 2000 or Garmin CANet.\u003c\/li\u003e\n\u003cli\u003eOptional fuel level input from an existing fuel gauge circuit or tank level sensor for on-screen tank level information.\u003c\/li\u003e\n\u003cli\u003eWorks in 3\/8 in. (9.5 mm) fuel hose runs, with 2 to 50 gal\/hr (7.5 to 190 L\/h) operating flow range.\u003c\/li\u003e\n\u003cli\u003eSingle-line fuel system use; not for installations where fuel returns to the tank through a return line.\u003c\/li\u003e\n\u003cli\u003e10 to 22 Vdc power requirement with a 0.25 A fuse and NMEA 2000 LEN of 1 for network planning.\u003c\/li\u003e\n\u003cli\u003eInstallation guidance that helps reduce air-bubble errors, including mounting so fuel flows upward through the sensor and following the flow-direction arrow.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eWhat’s included\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eGFS 10 fuel sensor unit\u003c\/li\u003e\n\u003cli\u003e4 reusable stainless-steel hose clamps\u003c\/li\u003e\n\u003cli\u003e3\/8 in. in-line fuel filter\u003c\/li\u003e\n\u003cli\u003eMounting hardware\u003c\/li\u003e\n\u003cli\u003eCANet adapter\u003c\/li\u003e\n\u003cli\u003eNMEA 2000 T-connector\u003c\/li\u003e\n\u003cli\u003eInstallation instructions\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis sensor is for gasoline-engine fuel systems and is not for diesel fuel systems. It is intended for single-line fuel systems; do not install it on engines that have a return line back to the fuel tank. Fuels with more than 10% ethanol (such as E85) are not supported.\u003c\/p\u003e\u003cp\u003eOn pressurized fuel-injected systems, the sensor must be installed on the low-pressure side of the high-pressure fuel pump. Systems with large engine-mounted fuel reservoirs can cause erratic flow readings, so it is a better match for typical marine setups that feed the engine without a large reservoir between the sensor and the engine.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003ePlan the install location so the sensor sits as far from the engine as practical and is not exposed to excess heat or vibration. Avoid placing it between the engine and the priming bulb (when a priming bulb is used). Install it above the maximum fuel level of the tank and mount the sensor and filter to a solid structure so the fuel hose is supported and does not hang on the fittings.\u003c\/p\u003e\u003cp\u003eFollow the flow arrow on the housing and mount the sensor so fuel flows upward through it to help prevent air-bubble related errors. Keep a clean, dry work area, drain the hose where possible, and check the installation for leaks periodically.\u003c\/p\u003e\u003ch6\u003eElectrical and network integration\u003c\/h6\u003e\u003cp\u003ePower is supplied through the bare-wire power\/data cable and should be protected by a 0.25 A fuse installed close to the battery. The unit draws up to 0.5 W. If you choose to connect tank level, it can be wired into the existing fuel gauge circuit or to the tank level sensor where applicable.\u003c\/p\u003e\u003cp\u003eFor data, connect through NMEA 2000 using the included T-connector and the built-in NMEA 2000 drop cable (6 ft \/ 1.8 m). The power\/data cable is 25 ft (7.6 m) to help reach typical helm or distribution locations, and the sensor can also connect via Garmin CANet using the included adapter when that network is used onboard.\u003c\/p\u003e\u003ch6\u003eUse cases on board\u003c\/h6\u003e\u003cp\u003eThis is a practical add-on when you want fuel burn and fuel-used information visible at the helm, especially on boats where range planning matters on longer runs. It fits well on single-outboard, twin-outboard, and inboard gasoline setups where the fuel line routing allows the sensor and filter to be mounted securely away from engine heat and vibration.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eInspect hose clamps, filter connections, and mounting points regularly, especially after the first few outings and after winter layup. Replace the in-line fuel filter at the start of each season or about every 2,600 gallons (10,000 L), and re-check for seepage whenever the fuel system has been serviced.\u003c\/p\u003e","brand":"Garmin","offers":[{"title":"Default Title","offer_id":52269001769141,"sku":"QBP813005","price":209.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1298740_qbp813005.jpg?v=1771541407"},{"product_id":"qbp595698","title":"Attwood Marine Johnson\/Evinrude Fuel Line Kit, 6 ft x 3\/8 in","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Attwood Marine Johnson\/Evinrude Fuel Line Kit is a 6 ft x 3\/8 in outboard fuel line assembly for Johnson and Evinrude fuel systems, offered with different tank-end connector setups and with or without a fuel demand valve. It is built around a low-permeation, fiber-reinforced fuel hose with a multi-layer primer bulb, giving boat owners a practical replacement line for portable tank and outboard connections.\u003c\/p\u003e\u003cp\u003eThe hose is compatible with ethanol-blended fuel and is rated for use up to 100 C. EPA certified and CARB approved construction helps meet current requirements for marine fuel systems, while the 3\/8 in inside diameter supports the fuel flow commonly needed by larger outboards.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e6 ft fuel line length gives enough reach for many portable tank layouts without leaving excessive hose loose in the cockpit or splashwell.\u003c\/li\u003e\n\u003cli\u003e3\/8 in hose diameter supports strong fuel flow for Johnson and Evinrude outboard applications.\u003c\/li\u003e\n\u003cli\u003eLow-permeation, fiber-reinforced hose resists kinking and hardening when used with ethanol-blended fuel.\u003c\/li\u003e\n\u003cli\u003eMulti-layer primer bulb helps with quick manual priming before startup after storage, refueling, or line replacement.\u003c\/li\u003e\n\u003cli\u003eVariant options include tank-end connector differences and a fuel demand valve option for systems that need added protection against pressure-related engine flooding.\u003c\/li\u003e\n\u003cli\u003eSprayless tank connector configurations help reduce fuel spray when connecting or disconnecting a pressurized fuel line.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eVariants\u003c\/h6\u003e\u003cp\u003eThis fuel line kit is offered in three configurations. The main differences are the tank-end connection and whether a fuel demand valve is included.\u003c\/p\u003e\u003cp\u003eAcross the range, the kit is based on a 6 ft x 3\/8 in low-permeation fuel hose with a primer bulb for Johnson and Evinrude fuel systems. Match the tank-end fitting and fuel demand valve option to the fuel tank and outboard setup already on the boat.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e93806EUS7: Tank end 8838TM6 + 8838HF6, fuel demand valve no. This configuration uses the sprayless tank fitting and hose fitting setup without adding a fuel demand valve.\u003c\/li\u003e\n\u003cli\u003e93806EUSD7: Tank end 8838TM6 + 8838HF6, fuel demand valve yes. This version keeps the same sprayless tank-end setup and adds a fuel demand valve for systems where pressure control is part of the fuel line setup.\u003c\/li\u003e\n\u003cli\u003e93806ELP7: Tank end 8889LP6, fuel demand valve no. This configuration uses the 8889LP6 tank-end option and does not include a fuel demand valve.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and fit\u003c\/h6\u003e\u003cp\u003eCheck the tank connection, engine connection, and hose routing before installation. The 6 ft length works well when the portable tank is near the transom, under a seat, or in a nearby fuel locker, but it should still route without sharp bends, pinching, or contact with hot engine surfaces.\u003c\/p\u003e\u003cp\u003eOn sprayless connector versions, the tank fitting is intended for standard 1\/4 in NPT fuel tank outlets. Threaded fuel fittings should be installed carefully so the connection seals without stressing the tank outlet or hose fitting.\u003c\/p\u003e\u003ch6\u003eFuel system use\u003c\/h6\u003e\u003cp\u003eThis kit is a good match for boat owners replacing an aging Johnson or Evinrude outboard fuel line where the hose has become stiff, cracked, swollen, or slow to prime. It suits fishing boats, runabouts, tenders, and small cruising boats that use portable or accessible fuel tanks and need a ready-to-install line assembly.\u003c\/p\u003e\u003cp\u003eAfter installation, prime the bulb and inspect every connection before running the engine. Any smell of fuel, visible wetness, or loss of prime should be corrected before the boat leaves the dock or ramp.\u003c\/p\u003e","brand":"Attwood Marine","offers":[{"title":"8838TM6 + 8838HF6 \/ No","offer_id":52581862113461,"sku":"QBP595698-V1","price":74.99,"currency_code":"USD","in_stock":false},{"title":"8838TM6 + 8838HF6 \/ Yes","offer_id":52581862146229,"sku":"QBP595698-V2","price":89.99,"currency_code":"USD","in_stock":true},{"title":"8889LP6 \/ No","offer_id":52581862178997,"sku":"QBP595698-V3","price":64.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1332802_qbp595698.jpg?v=1780200832"},{"product_id":"qbp563212","title":"Attwood Marine Straight Fuel Tank Vent, Black Housing, Polypropylene, 5\/8 in Hose","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Attwood Marine 1607-1 is a straight black fuel tank vent for boats that use 5\/8 inch I.D. vent hose. It has a splash-resistant polypropylene body, meets ABYC ventilation specifications, and installs in a 7\/8 inch hole on hull sections up to 5\/8 inch thick.\u003c\/p\u003e\u003cp\u003eThis vent handles the airflow a fuel tank needs while filling and during normal tank breathing on the water. The straight layout works where the vent line can run cleanly to the hull side, and the polypropylene construction resists corrosion in wet marine service.\u003c\/p\u003e\u003cp\u003eIt is a practical replacement when an older vent is cracked, faded, or no longer sealing well at the hull. Boats with aluminum construction or owners trying to avoid extra metal hardware on the exterior often prefer this style for the same reason.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eStraight fuel tank vent layout for installations that do not need an angled fitting\u003c\/li\u003e\n\u003cli\u003eFits 5\/8 inch I.D. fuel tank vent hose\u003c\/li\u003e\n\u003cli\u003eBlack polypropylene body with splash-resistant construction\u003c\/li\u003e\n\u003cli\u003eCorrosion-resistant material for saltwater spray and wet cockpit or hull-side locations\u003c\/li\u003e\n\u003cli\u003eMeets ABYC ventilation specifications\u003c\/li\u003e\n\u003cli\u003eInstalls in a 7\/8 inch hole and suits hull thickness up to 5\/8 inch\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and fit\u003c\/h6\u003e\u003cp\u003eBefore ordering, check the inside diameter of the vent hose, the hull thickness where the vent passes through, and whether your existing setup uses a straight vent rather than a 90 degree body. Those three points matter more than the outside appearance when matching a replacement.\u003c\/p\u003e\u003cp\u003eOn most boats, installation is straightforward: the vent passes through the hull side, the retaining hardware secures it in place, and the vent hose clamps to the 5\/8 inch connection on the inside. This style is a good match where the hose run stays fairly direct and does not need a sharp turn right behind the fitting.\u003c\/p\u003e\u003ch6\u003eUse on board\u003c\/h6\u003e\u003cp\u003eThis vent suits small powerboats, aluminum boats, center consoles, and similar layouts where the fuel vent exits on the hull side and needs a simple straight fitting. It also makes sense for owners replacing aged plastic vents during fuel system service without changing the hose size or hull cutout.\u003c\/p\u003e","brand":"Attwood Marine","offers":[{"title":"Default Title","offer_id":52581866307765,"sku":"QBP563212","price":6.03,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1329621_qbp563212.webp?v=1780200918"},{"product_id":"qbp579146","title":"Attwood Marine Honda Fuel Line Fittings, Quick-Connect","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Attwood Marine Honda Fuel Tank and Hose Fittings is a range of Honda-style fuel line connectors for matching the fuel hose, portable tank, or engine end of an outboard fuel system. The available fittings cover 3\/8 inch I.D. fuel hose connections, a 1\/4 inch male NPT tank thread, and engine-end hose attachment depending on the selected configuration.\u003c\/p\u003e\u003cp\u003eThese fittings are made for use with leaded, unleaded, ethanol-blended, and alcohol-blended fuels. The range includes chrome-plated brass options for large-bore 90HP+ Honda tank and hose connections, plus an acetal engine-end fitting for Honda outboard fuel hose setups.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eHonda fuel connector options for tank, hose, and engine-end fuel line connection points.\u003c\/li\u003e\n\u003cli\u003e3\/8 inch hose barb configuration available for fuel lines with 3\/8 inch I.D. hose.\u003c\/li\u003e\n\u003cli\u003e1\/4 inch male NPT tank fitting available for large-bore 90HP+ Honda fuel tank applications.\u003c\/li\u003e\n\u003cli\u003eChrome-plated brass variants support the tank and hose fittings used together on 90HP+ large-bore setups.\u003c\/li\u003e\n\u003cli\u003eAcetal engine-end variant fits the Honda engine-side hose connection and uses a rectangular locking post style.\u003c\/li\u003e\n\u003cli\u003eCompatible with leaded, unleaded, ethanol-blended, and alcohol-blended marine fuels.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eVariants\u003c\/h6\u003e\u003cp\u003eThis product is offered in three configurations so the connection point can match the fuel system layout on board.\u003c\/p\u003e\u003cp\u003eThe variants differ by fitting type, material, and application. The 8902-6 hose fitting and 8901-6 tank fitting are the matching large-bore 90HP+ chrome-plated brass pair, while the 8900-6 is the acetal engine-end hose fitting.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e8902-6: Hose female fitting in chrome-plated brass for 90HP+ large-bore applications. This version fits 3\/8 inch I.D. fuel hose and mates with the 8901-6 tank fitting.\u003c\/li\u003e\n\u003cli\u003e8900-6: Hose female fitting in acetal for the engine end. This version is used at the Honda outboard side of the fuel hose and has the rectangular locking post style.\u003c\/li\u003e\n\u003cli\u003e8901-6: Tank male fitting in chrome-plated brass for 90HP+ large-bore applications. This version uses a 1\/4 inch male NPT thread and mates with the 8902-6 hose fitting.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and fit\u003c\/h6\u003e\u003cp\u003eMatch the fitting to the exact connection point before installation: hose female for the fuel line, tank male for the tank outlet, or engine-end hose female for the outboard connection. The hose barb versions are intended for 3\/8 inch I.D. fuel hose, so the hose size should be confirmed before replacing an existing connector.\u003c\/p\u003e\u003cp\u003eThreaded fuel fittings should be installed with fuel-compatible thread sealant on the threads. Hose clamps are not included, so the correct clamps for the fuel hose and installation method need to be supplied separately.\u003c\/p\u003e\u003ch6\u003eUse cases on board\u003c\/h6\u003e\u003cp\u003eThis range is a practical match for replacing worn Honda fuel connectors, setting up a spare fuel line, or pairing a portable tank with the correct large-bore fitting. It suits small-boat and outboard installations where the buyer needs to match the connector location and fuel hose size rather than replace the full fuel system.\u003c\/p\u003e","brand":"Attwood Marine","offers":[{"title":"Tank Male \/ Chrome-Plated Brass \/ 90HP+ (Large Bore)","offer_id":52581894291637,"sku":"QBP579146-V1","price":7.99,"currency_code":"USD","in_stock":true},{"title":"Hose Female \/ Chrome-Plated Brass \/ 90HP+ (Large Bore)","offer_id":52581894324405,"sku":"QBP579146-V2","price":14.99,"currency_code":"USD","in_stock":true},{"title":"Hose Female \/ Acetal \/ Engine End","offer_id":52581894357173,"sku":"QBP579146-V3","price":7.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1332681_qbp579146.png?v=1780201340"},{"product_id":"qbp877189","title":"Attwood Marine Yamaha Female Fuel Hose Fitting, Acetal, Tank or Engine End","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Attwood Marine Yamaha Hose Female Fuel Fitting is a female quick-connect hose-end fitting for Yamaha-style outboard fuel systems, used at the tank or engine end depending on the setup. This parent product covers two barb sizes, 5\/16 in and 3\/8 in, so the fitting can be matched to the inside diameter of the fuel hose already on the boat.\u003c\/p\u003e\u003cp\u003eIt is made for portable tank and outboard fuel line connections where a clean, secure hose-to-fitting transition matters, especially on small boats, tenders, fishing boats, and repower or fuel-line replacement jobs. The fitting mates with the Attwood 8897-6 Yamaha tank fitting and is suitable for leaded, unleaded, ethanol-blended, and alcohol-blended fuels.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eFemale Yamaha-style quick-connect fitting for fuel hose assemblies at the tank or engine end.\u003c\/li\u003e\n\u003cli\u003eAvailable with 5\/16 in or 3\/8 in barb sizes to match common marine fuel hose inside diameters.\u003c\/li\u003e\n\u003cli\u003eAcetal construction helps keep the fitting light and practical for exposed fuel-line connections on board.\u003c\/li\u003e\n\u003cli\u003eCompatible with Attwood 8897-6 Yamaha tank fitting for matching quick-connect fuel system setups.\u003c\/li\u003e\n\u003cli\u003eSuitable for leaded, unleaded, ethanol-blended, and alcohol-blended marine fuels.\u003c\/li\u003e\n\u003cli\u003eHose clamps are not included, so the installation can be completed with clamps sized for the selected hose.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eVariants\u003c\/h6\u003e\u003cp\u003eThis fitting is offered in two hose barb configurations for matching the fuel hose size used on the boat.\u003c\/p\u003e\u003cp\u003eThe connection style and Yamaha-style female fuel fitting function are consistent across the range, while the barb size changes to suit 5\/16 in or 3\/8 in hose.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e88FHY516-6: Hose size 5\/16 in barb. This size fits 5\/16 in inside-diameter fuel hose and is a common choice when replacing or building a smaller outboard fuel line assembly.\u003c\/li\u003e\n\u003cli\u003e8896LP6: Hose size 3\/8 in barb. This size fits 3\/8 in inside-diameter fuel hose and works for fuel line setups that use the larger hose size.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and fit\u003c\/h6\u003e\u003cp\u003eMatch the barb size to the fuel hose inside diameter before installation. The fitting should be secured with fuel-line clamps, and any threaded connection in the matching fuel system should be assembled with fuel-compatible thread sealant where threads are used.\u003c\/p\u003e\u003cp\u003eBefore running the engine, check the connection by priming the fuel line and inspecting for leaks at the barb, clamp area, and quick-connect interface. This is especially important after replacing old hose, changing tanks, or servicing a fuel line that has been exposed to sun, salt, or repeated removal.\u003c\/p\u003e\u003ch6\u003eUse cases on board\u003c\/h6\u003e\u003cp\u003eThis fitting is a practical replacement part for portable outboard fuel lines, spare tank setups, and routine maintenance on Yamaha-style fuel systems. It suits boaters who need to refresh a worn connector, build a new fuel hose assembly, or keep a properly sized spare fitting on board for dockside or ramp-side repairs.\u003c\/p\u003e","brand":"Attwood Marine","offers":[{"title":"5\/16\" Barb","offer_id":52581894946997,"sku":"QBP877189-V1","price":4.99,"currency_code":"USD","in_stock":true},{"title":"3\/8\" Barb","offer_id":52581894979765,"sku":"QBP877189-V2","price":5.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1332704_qbp877189.webp?v=1780201347"},{"product_id":"qbp749094","title":"Attwood Marine Fuel Line Kit, For Honda Engines, 3\/8 in x 6 ft, EPA Compliant","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThis Attwood Marine Honda fuel line kit is a 6 ft. x 3\/8 in. outboard fuel line assembly for Honda brand engines and tanks. It gives boat owners a ready fuel hose setup for portable tank installations, replacement fuel lines, and engine rigging where a 3\/8 in. line is the correct size.\u003c\/p\u003e\u003cp\u003eThe kit uses a low-permeation fuel line with a multi-layer primer bulb and is listed as EPA certified and CARB approved. It is also compatible with ethanol blended fuels, which matters for many trailer boats, fishing boats, tenders, and other small craft that run pump gasoline.\u003c\/p\u003e\u003cp\u003eTwo configurations are available, with the main difference being the tank-end fitting arrangement and whether the tank fitting is included. This lets the same fuel line kit family cover setups that need a tank-side fitting and setups where the tank already has the required connection.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e6 ft. fuel hose length with 3\/8 in. inside diameter for Honda outboard fuel supply setups that use this line size.\u003c\/li\u003e\n\u003cli\u003eLow-permeation hose construction helps reduce fuel vapor loss compared with older conventional fuel lines.\u003c\/li\u003e\n\u003cli\u003eMulti-layer primer bulb supports manual priming at startup and after the fuel line has been disconnected or serviced.\u003c\/li\u003e\n\u003cli\u003eEPA certified and CARB approved configuration for current marine fuel system requirements.\u003c\/li\u003e\n\u003cli\u003eCompatible with ethanol blended fuels commonly used in portable marine gasoline systems.\u003c\/li\u003e\n\u003cli\u003eAvailable with or without the tank fitting, depending on how the boat’s portable fuel tank is already equipped.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eVariants\u003c\/h6\u003e\u003cp\u003eThis product is offered in two configurations for Honda fuel systems. Both use the same 6 ft. x 3\/8 in. fuel line format, while the tank-end fittings and included tank fitting differ by variant.\u003c\/p\u003e\u003cp\u003eThe tank-end choice matters when replacing an existing hose or setting up a new portable tank. A kit with the tank fitting is useful when the tank side needs to be completed, while the no-tank-fitting version suits installations where the matching tank connection is already in place.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e93806HUS7 includes tank end fittings 8838TM6 and 8838HF6, with the tank fitting included. This configuration fits a setup where the tank-side connection needs both the tank fitting and the hose-side fitting.\u003c\/li\u003e\n\u003cli\u003e93806HLP7 includes tank end fitting 8902-6, with no tank fitting included. This configuration is for installations where the tank fitting is already present and only the hose-side tank connection is needed.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and fit\u003c\/h6\u003e\u003cp\u003eBefore installation, confirm that the engine and tank are Honda-compatible and that a 3\/8 in. fuel line is appropriate for the outboard’s fuel demand and the existing fittings. Check the routing from the portable tank to the engine so the 6 ft. length can reach without tight bends, pinch points, or contact with hot engine parts.\u003c\/p\u003e\u003cp\u003eUse a route that lets the primer bulb sit where it can be reached and oriented correctly during priming. After connecting the line, prime the system and inspect every connection for leaks before running the engine away from the dock or ramp.\u003c\/p\u003e\u003ch6\u003eUse cases on board\u003c\/h6\u003e\u003cp\u003eThis kit is a practical match for small boats, tenders, skiffs, and fishing boats using Honda portable fuel tanks or Honda-compatible fuel connections. It is also useful as a replacement line when an older hose has hardened, kinked, or no longer primes cleanly.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eInspect the hose, primer bulb, and fittings regularly for cracking, stiffness, fuel odor, or seepage. Salt, sunlight, fuel residue, and storage heat can shorten the life of fuel system parts, so replacing a worn line before it fails is a smart part of routine boat maintenance.\u003c\/p\u003e","brand":"Attwood Marine","offers":[{"title":"8838TM6 + 8838HF6 \/ Yes","offer_id":52581897994421,"sku":"QBP749094-V1","price":74.99,"currency_code":"USD","in_stock":true},{"title":"8902-6 \/ No","offer_id":52581898027189,"sku":"QBP749094-V2","price":0.0,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1332828_qbp749094.webp?v=1780201406"},{"product_id":"qbp876216","title":"Attwood Marine Universal Fuel Tank \u0026 Hose Fittings","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Attwood Marine Universal Fuel Tank \u0026amp; Hose Fittings is a range of replacement fuel system connectors for matching marine fuel tanks, hoses, elbows, anti-siphon valve locations, and in-line hose repair points. The range covers common small-boat fuel plumbing sizes, including 1\/4 in. NPT, 1\/4 in. NPTF, 3\/8 in. NPT, 5\/16 in. barb, 3\/8 in. barb, and a 3\/8 in. hose mender configuration.\u003c\/p\u003e\u003cp\u003eThese fittings are used where the fuel line needs a threaded tank connection, a hose barb transition, a 90-degree change in direction, an anti-siphon valve, or a splice for a 3\/8 in. fuel hose. Depending on the configuration, the fitting is made from brass or aluminum, with the in-line splice kit using a brass mender and stainless steel clamps.\u003c\/p\u003e\u003cp\u003eThe fittings are suitable for leaded, unleaded, ethanol-blended, and alcohol-blended fuels. Threaded connections should be installed with thread sealant on the threads, and the final installation should be checked for fuel leaks before the boat is put back in service.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eRange includes a 90-degree elbow, hose-barb fittings, anti-siphon valves, and an in-line fuel splice kit for 3\/8 in. hose repair.\u003c\/li\u003e\n\u003cli\u003eConnection options cover 1\/4 in. NPT, 1\/4 in. NPTF, 3\/8 in. NPT, 5\/16 in. barb, 3\/8 in. barb, and 3\/8 in. hose mender applications.\u003c\/li\u003e\n\u003cli\u003eBrass configurations are available for selected elbows, hose-barb fittings, and the in-line splice kit.\u003c\/li\u003e\n\u003cli\u003eAluminum configurations are available for selected hose-barb fittings and anti-siphon valve fittings.\u003c\/li\u003e\n\u003cli\u003eSuitable for leaded, unleaded, ethanol-blended, and alcohol-blended fuels used in marine fuel systems.\u003c\/li\u003e\n\u003cli\u003eThreaded versions use male thread connections, with sealant required on the threads during installation.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eVariants\u003c\/h6\u003e\u003cp\u003eThis product family is offered in several configurations, with the main differences being fitting type, thread size, barb or mender size, and material. The range includes elbow, hose barb, anti-siphon valve, and in-line splice kit versions, so the correct option depends on the tank outlet, hose inside diameter, and whether the installation needs a straight connection, a 90-degree connection, a siphon-control valve, or a hose repair splice.\u003c\/p\u003e\u003cp\u003eAcross the range, the verified connection sizes include 1\/4 in. NPT x 1\/4 in. NPTF, 1\/4 in. NPT x 5\/16 in. barb, 1\/4 in. NPT x 3\/8 in. barb, 3\/8 in. NPT x 3\/8 in. barb, and 3\/8 in. hose mender. Material varies by configuration, with brass and aluminum options available.\u003c\/p\u003e\u003ch6\u003eInstallation and fit\u003c\/h6\u003e\u003cp\u003eMatch the threaded side to the tank or fuel system port and match the barb or mender side to the fuel hose size. A 5\/16 in. barb is not interchangeable with a 3\/8 in. barb, and NPT thread size should be checked before installation rather than forced into an unmatched port.\u003c\/p\u003e\u003cp\u003eFor threaded fittings, apply a fuel-compatible thread sealant to the threads and tighten the fitting so it seats securely without over-stressing the tank fitting or adapter. Hose-barb connections should be secured with the proper fuel-line clamp for the hose type and installation location.\u003c\/p\u003e\u003ch6\u003eUse cases on board\u003c\/h6\u003e\u003cp\u003eThese fittings are a practical match for maintenance work on small gasoline-powered boats, outboard fuel systems, portable or fixed tank connections, and dockside fuel line repairs where the existing hose or tank fitting size is already known. The anti-siphon valve options are used where the fuel system requires siphon control at the tank connection.\u003c\/p\u003e\u003cp\u003eThe in-line splice configuration is useful for repairing a damaged section of 3\/8 in. fuel hose when replacing the full hose run is not practical at the time. After any fuel system work, the line should be inspected under normal operating conditions and any sign of seepage, odor, or soft hose should be addressed before use.\u003c\/p\u003e","brand":"Attwood Marine","offers":[{"title":"Elbow \/ 1\/4\" NPT x 1\/4\" NPTF \/ Brass","offer_id":52581912051893,"sku":"QBP876216-V1","price":7.99,"currency_code":"USD","in_stock":false},{"title":"Hose Barb \/ 1\/4\" NPT x 5\/16\" Barb \/ Male Thread","offer_id":52581912084661,"sku":"QBP876216-V2","price":4.99,"currency_code":"USD","in_stock":true},{"title":"Hose Barb \/ 1\/4\" NPT x 3\/8\" Barb \/ Male Thread","offer_id":52581912117429,"sku":"QBP876216-V3","price":7.99,"currency_code":"USD","in_stock":true},{"title":"Hose Barb \/ 3\/8\" NPT x 3\/8\" Barb \/ Male Thread","offer_id":52581912150197,"sku":"QBP876216-V4","price":5.99,"currency_code":"USD","in_stock":true},{"title":"Anti-Siphon Valve \/ 1\/4\" NPT x 3\/8\" Barb \/ Aluminum","offer_id":52581912182965,"sku":"QBP876216-V5","price":12.99,"currency_code":"USD","in_stock":false},{"title":"Anti-Siphon Valve \/ 3\/8\" NPT x 3\/8\" Barb \/ Aluminum","offer_id":52581912215733,"sku":"QBP876216-V6","price":24.99,"currency_code":"USD","in_stock":false},{"title":"In-Line Fuel Splice Kit \/ 3\/8\" Hose Mender \/ Brass","offer_id":52581912248501,"sku":"QBP876216-V7","price":7.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1333103_qbp876216.webp?v=1780201488"},{"product_id":"qbp306334","title":"Perko Pipe to Hose Adapter, Cast Bronze, Cast Hex, Machined Hose Barb, 1 Pc","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Perko Figure No. 0076 is a cast bronze pipe to hose adapter for connecting matching pipe-size fittings to marine hose in boat plumbing or gasoline fuel system installations. It uses a straight adapter format with a precision-machined hose barb and a cast hex section that gives a wrench a clean contact point during installation.\u003c\/p\u003e\u003cp\u003eThis range covers 2 inch, 2-1\/2 inch, and 3 inch pipe-to-hose sizes, with overall lengths from 2-5\/8 inches to 4-3\/4 inches depending on the variant. The fitting is part of Perko underwater hardware and meets the requirements of U.S.C.G. Safety Standards for gasoline fuel systems, 33 CFR 183, dated January 31, 1977.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eCast bronze construction for marine plumbing environments where corrosion resistance matters.\u003c\/li\u003e\n\u003cli\u003eStraight pipe-to-hose adapter format for joining same-size pipe and hose connections.\u003c\/li\u003e\n\u003cli\u003ePrecision-machined hose barb helps the hose seat properly when installed with the correct marine hose and clamps.\u003c\/li\u003e\n\u003cli\u003eCast hex section gives a wrench a solid contact point and makes installation easier in tight bilge, engine room, or machinery-space locations.\u003c\/li\u003e\n\u003cli\u003eAvailable in 2 inch, 2-1\/2 inch, and 3 inch sizes to match larger onboard plumbing and fuel-system layouts.\u003c\/li\u003e\n\u003cli\u003eMeets U.S.C.G. Safety Standards for gasoline fuel systems under 33 CFR 183.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eVariants\u003c\/h6\u003e\u003cp\u003eThis Perko pipe to hose adapter is offered in multiple size configurations for matching the pipe side, hose side, and available installation space.\u003c\/p\u003e\u003cp\u003eThe size, hose connection, pipe connection, overall length, and shipping weight vary by variant. The cast bronze construction, straight adapter style, cast hex, precision-machined hose barb, and U.S.C.G. gasoline fuel system compliance are consistent across these listed variants.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e0076009PLB: 2 inch pipe size, 2 inch hose size, and 2-5\/8 inch overall length. This is the shortest option in this group, useful where the plumbing run needs a 2 inch connection with limited straight-line space.\u003c\/li\u003e\n\u003cli\u003e0076010PLB: 2-1\/2 inch pipe size, 2-1\/2 inch hose size, and 4 inch overall length. This size fits installations that step up to 2-1\/2 inch hose and pipe while keeping the same straight adapter layout.\u003c\/li\u003e\n\u003cli\u003e0076011PLB: 3 inch pipe size, 3 inch hose size, and 4-3\/4 inch overall length. This is the largest option in the group, suited to larger hose runs where the system is built around 3 inch connections.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and fit\u003c\/h6\u003e\u003cp\u003eMatch the adapter size to both sides of the system before ordering. The pipe size and hose size are intended to correspond on each variant, so the fitting should be selected by the vessel’s existing pipe connection, hose inside diameter, and the straight length available around the fitting.\u003c\/p\u003e\u003cp\u003eDuring installation, the hose barb should be fully seated in the hose and secured with marine clamps appropriate for the application. The cast hex helps with tightening the pipe side without using the hose barb as the wrenching surface.\u003c\/p\u003e\u003ch6\u003eUse on board\u003c\/h6\u003e\u003cp\u003eThis adapter is a practical fit for boat owners, yards, and technicians working on larger plumbing connections where a cast bronze fitting is preferred over lighter-duty hardware. It is especially relevant in bilge, engine room, and fuel-system service areas where the fitting size, material, and compliance standard need to be checked before installation.\u003c\/p\u003e","brand":"Perko","offers":[{"title":"2-5\/8","offer_id":52581921423541,"sku":"QBP306334-V1","price":65.26,"currency_code":"USD","in_stock":false},{"title":"4","offer_id":52581921456309,"sku":"QBP306334-V2","price":0.0,"currency_code":"USD","in_stock":false},{"title":"4-3\/4","offer_id":52581921489077,"sku":"QBP306334-V3","price":0.0,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1334726_qbp306334.webp?v=1780201568"}],"url":"https:\/\/www.qualityboatparts.com\/collections\/fuel-line-connectors.oembed","provider":"Quality Boat Parts","version":"1.0","type":"link"}