{"title":"Trolling Motor Accessories","description":"","products":[{"product_id":"qbp426054","title":"MotorGuide Trolling Motor Power Plug, 2-Prong, 50A, 12-36V","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe MotorGuide 8M4000953 is a 2-prong trolling motor power plug rated for 50 amps for 12V, 24V, or 36V power systems.\u003c\/p\u003e\u003cp\u003eIt creates a clean disconnect point between your trolling motor and the boat’s power circuit, which is handy when you remove the motor for trailering, store the boat, or need to service wiring at the bow. If your current plug feels loose, shows heat marks, or cuts out when the boat bumps, replacing the connector is a smart place to start.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e2-prong trolling motor power plug format\u003c\/li\u003e\n\u003cli\u003e50 A rating for high-current trolling motor circuits\u003c\/li\u003e\n\u003cli\u003eWorks with 12V, 24V, and 36V trolling motor power setups\u003c\/li\u003e\n\u003cli\u003eBuilt to seat firmly in a matching receptacle for a steady connection\u003c\/li\u003e\n\u003cli\u003eMakes it easier to disconnect power at the bow for storage, trailering, or maintenance\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis plug is intended to mate with a matching 2-prong, 50 A trolling motor receptacle. Before ordering, compare the prong layout and housing style to what’s installed on your boat, since 2-prong plugs are not all interchangeable across brands and patterns.\u003c\/p\u003e\u003cp\u003eVoltage is not usually the limiting factor here since the plug supports 12V through 36V. The important checks are connector style and that your circuit protection and wiring are appropriate for a 50 A connector and your trolling motor’s current draw.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eDisconnect the batteries before any wiring work. Make electrical connections with marine-appropriate crimping and sealing so water and corrosion do not creep into the joint over time. Add strain relief and route the cable so the plug is not taking the load when the motor turns, stows, or gets bumped.\u003c\/p\u003e\u003cp\u003eOn open decks, place the connection point where it will not sit in standing water and where it is less likely to take direct washdowns. Keeping the contacts clean and the fit tight helps prevent heat build-up on high-current trolling motor runs.\u003c\/p\u003e\u003ch6\u003eUse on board\u003c\/h6\u003e\u003cp\u003eThis style of plug is commonly used on bow-mount trolling motor installs where you want a quick disconnect close to the motor bracket. It also fits small-boat and removable-motor setups where you regularly pull the motor between trips, as long as the mating receptacle matches the same 2-prong 50 A pattern.\u003c\/p\u003e\u003ch6\u003eCompliance and warnings\u003c\/h6\u003e\u003cp\u003eCalifornia Proposition 65 warning: This product can expose you to chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm. For more information, visit P65Warnings.ca.gov.\u003c\/p\u003e\n\u003cspan itemprop=\"mpn\" hidden\u003e8M4000953\u003c\/span\u003e","brand":"MotorGuide","offers":[{"title":"Default Title","offer_id":53721527091381,"sku":"QBP426054","price":31.0,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1280716_qbp426054.jpg?v=1794116309"},{"product_id":"qbp622994","title":"StrikeMaster Lazer™ Power 10\" Replacement Blades LPD-10PB","description":"\u003cp\u003e\u003cstrong\u003eLazer™ Power 10\" Replacement Blades\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eTwin Serrated, Stainless Steel Lazer Blades for Lazer Power Augers. Includes four blade screws and two blades. Lazer Mag, Lazer Mag Xpress, Lazer XL-3000, Electra Lazer, Lazer Pro, Lazer 224 \u0026amp; Lite-Flite.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eFeatures:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eTwin Serrated, Stainless Steel Lazer Blades for Lazer Power Augers\u003c\/li\u003e\n\u003cli\u003eIncludes four blade screws and two blades\u003c\/li\u003e\n\u003cli\u003eLazer Mag, Lazer Mag Xpress, Lazer XL-3000, Electra Lazer, Lazer Pro \u0026amp; Lazer 224 and Lite-Flite\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cimg src=\"https:\/\/productimageserver.com\/prop65\/6pt.png\" alt=\"Warning\"\u003e\u003cstrong\u003eWARNING:\u003c\/strong\u003e This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to \u003ca href=\"http:\/\/P65Warnings.ca.gov\"\u003eP65Warnings.ca.gov\u003c\/a\u003e.\u003c\/p\u003e\n\u003cspan itemprop=\"mpn\" hidden\u003eLPD-10PB\u003c\/span\u003e","brand":"StrikeMaster","offers":[{"title":"Default Title","offer_id":53721527386293,"sku":"QBP622994","price":69.12,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1110542_qbp622994jpg.jpg?v=1794116348"},{"product_id":"qbp417475","title":"MotorGuide Trolling Motor Power Receptacle, 50A, 2-Prong, 12\/24\/36V","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe MotorGuide 8M4000954 is a 50A trolling motor power receptacle that gives you a solid two-prong connection for 12V, 24V, or 36V systems.\u003c\/p\u003e\u003cp\u003eIt’s the boat-side connection point that pairs with the matching MotorGuide 50A trolling motor plug to make a clean quick-disconnect at the bow. That’s handy when you trailer often, pull the motor for storage, or want a simple way to isolate trolling motor power without leaving loose leads exposed.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e50A continuous rating for trolling motor power connections\u003c\/li\u003e\n\u003cli\u003eTwo-prong receptacle for 12V, 24V, or 36V setups\u003c\/li\u003e\n\u003cli\u003eMatches the MotorGuide 50A Trolling Motor Plug (8M4000953)\u003c\/li\u003e\n\u003cli\u003eCreates a quick-disconnect point near the trolling motor mount for faster rigging and removal\u003c\/li\u003e\n\u003cli\u003eFixed receptacle location helps keep the bow wiring tidy and easier to secure\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis receptacle is meant for trolling motor installations using a two-prong, 50A-style plug connection. Confirm your trolling motor lead uses the matching two-prong plug style and that the rest of your wiring and overcurrent protection are appropriate for a 50A connection point.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eMount the receptacle where the trolling motor lead can reach without being stretched during stow and deploy, commonly near the bow panel or close to a quick-release bracket location. Route the boat-side feed so it’s supported along the run, protected from chafe, and kept out of standing water.\u003c\/p\u003e\u003cp\u003eAfter wiring, keep the connection clean and dry in use, and periodically check for heat discoloration, looseness, or corrosion. A small amount of dielectric grease on the contact surfaces can help slow oxidation in humid or salt-affected environments.\u003c\/p\u003e\u003ch6\u003eSafety notice\u003c\/h6\u003e\u003cp\u003eWARNING: Cancer and reproductive harm - www.P65Warnings.ca.gov.\u003c\/p\u003e\n\u003cspan itemprop=\"mpn\" hidden\u003e8M4000954\u003c\/span\u003e","brand":"MotorGuide","offers":[{"title":"Default Title","offer_id":53721528402101,"sku":"QBP417475","price":31.0,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1280685_qbp417475.jpg?v=1794116446"},{"product_id":"qbp629675","title":"MotorGuide Telescoping Tiller Extension Handle, 24 in, Aluminum Tubing, Soft-Grip","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe MotorGuide MGA503A1 is a 24 inch telescoping extension handle that gives you extra reach when steering a transom-mounted tiller. It is a simple way to move your steering position forward in the boat while keeping your hand on the tiller where you need it during long trolling passes.\u003c\/p\u003e\u003cp\u003eThis extension locks in place once set, so the length stays put while you are underway. It uses aluminum tubing with a soft-grip handle, and the connector adjusts for a solid connection on many hand-steered trolling motor tillers and popular tiller kicker engines.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e24 inch telescoping tiller extension for hand-steered transom setups\u003c\/li\u003e\n\u003cli\u003eLocking length adjustment to keep the handle from creeping while you steer\u003c\/li\u003e\n\u003cli\u003eAluminum tubing construction with a soft-grip handle for better control with wet hands\u003c\/li\u003e\n\u003cli\u003eAdjustable connector that clamps down for a firm, no-wobble feel when installed correctly\u003c\/li\u003e\n\u003cli\u003eMade for trolling motors and commonly used on tiller-style kicker applications where extra reach helps\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis handle is meant for transom-mount, hand-steered tiller motors and similar tiller-style controls. Before ordering, check that your tiller has enough straight grip area for the connector to clamp securely, and confirm you have clearance for the extension to sweep through your steering arc without hitting a seat, gunwale, or console.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eFit the connector onto the tiller handle, adjust it for a snug clamp, and confirm the extension does not interfere with normal steering movement. Set the telescoping length where it feels natural from your usual driving position, then verify it locks firmly before running in chop or making tight turns.\u003c\/p\u003e\u003ch6\u003eUse on board\u003c\/h6\u003e\u003cp\u003eOn smaller fishing boats, skiffs, and utility hulls, an extension handle helps when you are trolling from a mid-boat seat or standing a bit forward for visibility and balance. It is a good match for anglers who run a hand-steered transom motor for slow trolling and want a more comfortable reach without changing the rest of the setup.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eAfter use, especially in saltwater, rinse the handle and connector with fresh water and let it dry before storage. Keep the telescoping section clean so it slides smoothly, and re-check clamp tightness periodically since vibration can loosen hardware over time.\u003c\/p\u003e\u003ch6\u003eSafety notice\u003c\/h6\u003e\u003cp\u003eWARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.\u003c\/p\u003e\n\u003cspan itemprop=\"mpn\" hidden\u003eMGA503A1\u003c\/span\u003e","brand":"MotorGuide","offers":[{"title":"Default Title","offer_id":53721530761397,"sku":"QBP629675","price":29.91,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1280726_qbp629675.jpg?v=1794116736"},{"product_id":"qbp623059","title":"StrikeMaster Lazer™ Power 8\" Replacement Blades LPD-8PB","description":"\u003cp\u003e\u003cstrong\u003eLazer™ Power 8\" Replacement Blades\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eTwin Serrated, Stainless Steel Lazer Blades for Lazer Power Augers. Includes four blade screws and two blades. Lazer Mag, Lazer Mag Xpress, Lazer XL-3000, Electra Lazer, Lazer Pro, Lazer 224 \u0026amp; Lite-Flite.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eFeatures:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eTwin Serrated, Stainless Steel Lazer Blades for Lazer Power Augers\u003c\/li\u003e\n\u003cli\u003eIncludes four blade screws and two blades\u003c\/li\u003e\n\u003cli\u003eLazer Mag, Lazer Mag Xpress, Lazer XL-3000, Electra Lazer, Lazer Pro \u0026amp; Lazer 224 and Lite-Flite\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cimg src=\"https:\/\/productimageserver.com\/prop65\/6pt.png\" alt=\"Warning\"\u003e\u003cstrong\u003eWARNING:\u003c\/strong\u003e This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to \u003ca href=\"http:\/\/P65Warnings.ca.gov\"\u003eP65Warnings.ca.gov\u003c\/a\u003e.\u003c\/p\u003e\n\u003cspan itemprop=\"mpn\" hidden\u003eLPD-8PB\u003c\/span\u003e","brand":"StrikeMaster","offers":[{"title":"Default Title","offer_id":53721536200885,"sku":"QBP623059","price":59.24,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1110542_qbp622994jpg.jpg?v=1794116348"},{"product_id":"qbp425590","title":"MotorGuide Xi Series Trolling Motor Foot Pedal, Wireless 2.4GHz","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe MotorGuide 8M0092069 is a 2.4 GHz wireless foot pedal for Xi series electric steer trolling motors, including Xi3 and Xi5 models. The heel-toe steering layout lets you turn right with toe-down and left with heel-down, then stop the turn by letting the pedal return to the center detent. Steering range allows you to rotate the motor past 360 degrees in either direction, which is handy when you are lining up on structure or following a contour.\u003c\/p\u003e\u003cp\u003eSpeed is set with the dial on the pedal, with both momentary run and constant on\/off control at the selected speed. The pedal runs on two AA alkaline batteries and syncs to the motor receiver, so it can be placed where your feet naturally land on a casting deck or bow platform without a cable run across the boat.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e2.4 GHz wireless foot control for compatible MotorGuide Xi series motors (Xi3 and Xi5)\u003c\/li\u003e\n\u003cli\u003eHeel-toe steering with a center detent to stop turning without hunting for a switch\u003c\/li\u003e\n\u003cli\u003eSteering range that can rotate the motor past 360 degrees in either direction\u003c\/li\u003e\n\u003cli\u003eSpeed control dial plus both momentary run and constant propeller on\/off at the selected speed\u003c\/li\u003e\n\u003cli\u003eAnchor button control on motors with GPS installed, and it also functions as the pedal on\/off control\u003c\/li\u003e\n\u003cli\u003eReceiver can sync up to 40 wireless controllers for multi-control setups\u003c\/li\u003e\n\u003cli\u003eUses two AA alkaline batteries with a gasketed cover to help keep the battery compartment sealed\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis pedal is intended for MotorGuide Xi series motors that support wireless controllers. It is commonly used with Xi3 and Xi5 models and communicates through the motor’s receiver once it is synced, so there is no hardwired foot pedal connection to route through the deck. If your boat runs multiple wireless controls, the receiver can store many devices, which is useful when you want both a foot pedal and other controls on board.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eSyncing is done at power-up. After connecting the trolling motor to its power source, press and hold the propeller and anchor buttons on the pedal within ten seconds, then listen for the multi-tone beep that confirms the receiver learned the pedal. When activating more than one pedal, unplug the motor from power and plug it back in between each device activation.\u003c\/p\u003e\u003cp\u003eBattery access is under the cover secured by two screws. Replace with two AA alkaline batteries in the correct polarity and make sure the rubber seal is seated before reinstalling the cover.\u003c\/p\u003e\u003ch6\u003eUse cases on board\u003c\/h6\u003e\u003cp\u003eThis setup makes sense for anglers who want their trolling motor to respond while they are moving around the bow, working a rod locker, or landing a fish, since the pedal is not tied to a fixed cable location. It is also a good match for boats where keeping the deck clear matters, such as bass boats, multispecies rigs, and open-bow skiffs with a busy casting area.\u003c\/p\u003e\u003ch6\u003eSafety and compliance\u003c\/h6\u003e\u003cp\u003eRotating propellers can cause serious injury or death. Never start or operate the trolling motor out of water.\u003c\/p\u003e\u003cp\u003eWhen activating the trolling motor with the foot pedal, the motor can start at the last selected speed and course settings. Before pressing the pedal, hold on to a seat or handhold and advise passengers to do the same.\u003c\/p\u003e\u003cp\u003eWARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.\u003c\/p\u003e\n\u003cspan itemprop=\"mpn\" hidden\u003e8M0092069\u003c\/span\u003e","brand":"MotorGuide","offers":[{"title":"Default Title","offer_id":53721537773749,"sku":"QBP425590","price":369.69,"currency_code":"USD","in_stock":false}]},{"product_id":"qbp629579","title":"MotorGuide Mounting Isolator Kit, 4-Pack, Stainless Steel Bolts","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe MotorGuide MGA015PB6 is a mounting isolator kit that helps absorb shock and cut down vibration when you bolt marine accessories in place. It is commonly used for trolling motor mounts and other deck mounted hardware where vibration can work fasteners loose over time and where you want a cleaner install without needing full access under the deck or behind the console.\u003c\/p\u003e\u003cp\u003eThe kit uses rubber isolators with a molded-in nut and stainless steel bolts. As the bolts are tightened, the isolators expand into a mushroom shape under the mounting surface, helping the mount clamp down securely while the rubber takes the edge off impacts and vibration.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eRubber isolators help reduce vibration transfer into mounted electronics and accessories.\u003c\/li\u003e\n\u003cli\u003eMolded-in nut in each isolator simplifies tightening from the topside.\u003c\/li\u003e\n\u003cli\u003eIsolator expands into a mushroom shape as it is tightened to help hold the mount in place.\u003c\/li\u003e\n\u003cli\u003eUseful for installs with limited underside access under decks or behind consoles.\u003c\/li\u003e\n\u003cli\u003eStainless steel mounting bolts included for a clean bolt-through installation.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eWhat’s included\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e4 rubber isolators\u003c\/li\u003e\n\u003cli\u003e4 stainless steel bolts\u003c\/li\u003e\n\u003cli\u003eMounting instructions\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eLay out the mount, bracket, or accessory base and confirm your hole pattern and clearance before drilling. Insert the rubber isolators through the mounting holes, start the stainless bolts, then tighten until the rubber mushrooms under the surface and the assembly feels firm. The goal is a stable clamp with the rubber still doing its job, not crushing the isolator.\u003c\/p\u003e\u003cp\u003eAfter the first run, recheck fastener tightness. Vibration and deck materials can settle slightly, especially on the first outing after installation.\u003c\/p\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis kit is intended for bolt-through mounting applications where you want some isolation between the mount and the boat structure. It is a good match for trolling motor mounts and many other marine accessories that use standard bolts and washers for deck mounting. Confirm your deck thickness, hole size, and the space available below the mounting surface so the isolators can expand properly.\u003c\/p\u003e\u003ch6\u003eUse cases on board\u003c\/h6\u003e\u003cp\u003eIt is a practical choice for bass boats, bay boats, and center consoles where you are installing gear on the bow deck or near the console and access is tight. It can also be helpful on boats that see chop regularly and where sensitive electronics benefit from reduced shock transfer.\u003c\/p\u003e\u003ch6\u003eMaterials and corrosion resistance\u003c\/h6\u003e\u003cp\u003eThe isolators are rubber and the fasteners are stainless steel. The rubber helps isolate vibration at the mounting points while the stainless hardware suits typical wet, salt, and washdown conditions when installed with normal marine best practices.\u003c\/p\u003e\u003ch6\u003eSafety information\u003c\/h6\u003e\u003cp\u003eWARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.\u003c\/p\u003e\n\u003cspan itemprop=\"mpn\" hidden\u003eMGA015PB6\u003c\/span\u003e","brand":"MotorGuide","offers":[{"title":"Default Title","offer_id":53721538789557,"sku":"QBP629579","price":21.36,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1280717_qbp629579.jpg?v=1794117280"},{"product_id":"qbp417557","title":"MotorGuide Garmin 8-Pin HD+ Sonar Adapter Cable, Tour\/Tour Pro HD+","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe MotorGuide 8M4004178 is an HD+ sonar adapter cable that connects a Tour or Tour Pro HD+ trolling motor to a Garmin fishfinder that uses an 8-pin transducer port. It carries traditional 83\/200 kHz 2D sonar and 455\/800 kHz high-definition down-looking sonar signals so you can read bottom and structure directly under the trolling motor.\u003c\/p\u003e\u003cp\u003eThis is the clean way to use the trolling motor’s built-in sonar without adding an external transducer to the bracket. It is meant for HD+ enabled motors and it is not compatible with Xi Series motors.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eConnects MotorGuide Tour and Tour Pro HD+ sonar output to a Garmin 8-pin transducer port\u003c\/li\u003e\n\u003cli\u003ePasses 83\/200 kHz 2D sonar and 455\/800 kHz high-definition down-looking sonar signals from the trolling motor\u003c\/li\u003e\n\u003cli\u003eCompatible with Garmin GPSMAP and echoMAP series that use the Garmin 8-pin transducer connector\u003c\/li\u003e\n\u003cli\u003eGarmin SV models that use a 12-pin sounder connection require Garmin 8-pin transducer to 12-pin Sounder Adapter Cable with XID (010-12122-10), sold separately\u003c\/li\u003e\n\u003cli\u003eNot compatible with Xi Series motors\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eUse this cable only when you have a MotorGuide Tour or Tour Pro that is HD+ enabled and you want to plug that sonar into a Garmin unit with an 8-pin transducer input. If your Garmin unit does not have an 8-pin transducer port, confirm what adapter your display needs before ordering.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eConnect the motor end to the HD+ sonar lead from the trolling motor, then connect the Garmin end to the display’s 8-pin transducer port. Route the cable with a gentle drip loop and secure it so it cannot rub on the shaft, hinge points, or steering cables when stowing and deploying.\u003c\/p\u003e\u003cp\u003eFor the cleanest sonar picture, keep sonar cabling separated from high-current trolling motor power wiring where possible, and use strain relief at the head unit so vibration and trailering do not pull on the connector.\u003c\/p\u003e\u003ch6\u003eUse cases on board\u003c\/h6\u003e\u003cp\u003eThis is a good match for bow-mount setups where the angler wants sonar that tracks exactly where the trolling motor points, especially on bass boats and multi-species rigs that run Garmin electronics at the bow. It also helps on boats where you want fewer exposed transducer mounts and a simpler rigging layout.\u003c\/p\u003e\n\u003cspan itemprop=\"mpn\" hidden\u003e8M4004178\u003c\/span\u003e","brand":"MotorGuide","offers":[{"title":"Default Title","offer_id":53721540952245,"sku":"QBP417557","price":77.54,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1280691_qbp417557.jpg?v=1794117497"},{"product_id":"qbp425406","title":"MotorGuide Medium-Duty Trolling Motor Receptacle, 12\/24\/36V, 2\/3-Wire, 1-1\/8in Mounting Hole, 8\/10 AWG, Watertight Sealing Cap","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe MotorGuide 8M0092066 is a medium-duty trolling motor receptacle that mounts through a panel and gives you a quick disconnect point for trolling motor power.\u003c\/p\u003e\u003cp\u003eIt works with 12, 24, and 36 volt trolling motor systems and supports 2-wire or 3-wire configurations. The body installs through a standard 1-1\/8\" diameter mounting hole and accepts 8 AWG or 10 AWG wire.\u003c\/p\u003e\u003cp\u003eA sealing cap closes the opening when the plug is removed, and drain holes in the receptacle help keep water from sitting around the electrical contacts.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eCompatible with 12, 24, and 36 volt trolling motor power circuits\u003c\/li\u003e\n\u003cli\u003eWorks with 2-wire or 3-wire wiring layouts\u003c\/li\u003e\n\u003cli\u003eFits a standard 1-1\/8\" diameter mounting hole\u003c\/li\u003e\n\u003cli\u003eAccepts 8 AWG and 10 AWG wire\u003c\/li\u003e\n\u003cli\u003eCap seals the receptacle when not in use to help keep spray and rain out\u003c\/li\u003e\n\u003cli\u003eDrain holes help move water away from the electrical components\u003c\/li\u003e\n\u003cli\u003ePlated brass electrical components for consistent contact in a wet environment\u003c\/li\u003e\n\u003cli\u003eConstruction resists corrosion during marine use\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and wiring\u003c\/h6\u003e\u003cp\u003eMount the receptacle where you can reach it on the bow and where the back side stays accessible for wiring. After drilling the 1-1\/8\" hole, dry-fit the body so the cap can open fully and the cable can route without a tight bend.\u003c\/p\u003e\u003cp\u003eUse the wire gauge your trolling motor circuit calls for and keep connections tight so vibration does not work them loose over time. Circuit protection and conductor sizing should follow the trolling motor manufacturer guidance and your boat's electrical standards.\u003c\/p\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis is the receptacle side of a trolling motor quick-disconnect. Pair it with a matching trolling motor plug and confirm your system voltage and wire count before cutting the panel.\u003c\/p\u003e\u003ch6\u003eUse on board\u003c\/h6\u003e\u003cp\u003eA good match for boats that remove the trolling motor for trailering, storage, or service and want a consistent disconnect at the bow instead of hardwiring the leads.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eKeep the cap closed when the plug is removed, and rinse spray off the exterior after a day on the water. Periodically check terminal tightness and look for heat discoloration that can point to a loose connection.\u003c\/p\u003e\u003ch6\u003eRegulatory notice\u003c\/h6\u003e\u003cp\u003eWARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.\u003c\/p\u003e\n\u003cspan itemprop=\"mpn\" hidden\u003e8M0092066\u003c\/span\u003e","brand":"MotorGuide","offers":[{"title":"Default Title","offer_id":53721571852469,"sku":"QBP425406","price":45.34,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1280695_qbp425406.jpg?v=1794118544"},{"product_id":"qbp425717","title":"MotorGuide Universal Quick Release Mounting Bracket, For Cable \u0026 Electric-Steer Motors, Slides Inboard 5-3\/4 in, Anodized Aluminum","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe MotorGuide 8M0095972 is a universal quick-release mounting bracket that lets you remove and reinstall a MotorGuide trolling motor without unbolting the mount from the deck.\u003c\/p\u003e\u003cp\u003eThe two-plate system locks with a cam handle and a sliding wedge fit, and the base can shift the motor up to 5-3\/4 in. inboard for extra clearance when launching or loading.\u003c\/p\u003e\u003cp\u003eWith anodized aluminum plates and stainless mounting hardware, it holds up better around salt spray and routine washdowns.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eQuick-release two-plate bracket with a cam-lock handle for fast removal and reattachment.\u003c\/li\u003e\n\u003cli\u003eWorks with MotorGuide cable-steer and electric-steer trolling motors.\u003c\/li\u003e\n\u003cli\u003eSlide base repositions the motor up to 5-3\/4 in. inboard for clearance at the ramp, dock, or trailer.\u003c\/li\u003e\n\u003cli\u003eAnodized aluminum construction with stainless hardware to resist corrosion.\u003c\/li\u003e\n\u003cli\u003eHandle can be secured with the included clip or a padlock (padlock sold separately).\u003c\/li\u003e\n\u003cli\u003eExtra top plates are available separately for swapping between multiple motors.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eUse the bottom plate as a template, then drill four 17\/64 in. holes and through-bolt the base to the deck with the supplied 1\/4-20 x 3 in. hardware. Rubber washers sit between the plate and the deck, with flat washers and nylock nuts underneath.\u003c\/p\u003e\u003cp\u003eAttach your trolling motor mount bracket to the top plate using the provided 1\/4-20 screws. Two screw lengths are included so you can match the thickness of your motor mount and still get full thread engagement without the fasteners poking through the plate.\u003c\/p\u003e\u003cp\u003eTo attach the motor, leave the handle open, set the top plate onto the base, slide it toward port until the wedges engage, then close the handle. For removal, open the handle, slide toward starboard, and lift the motor straight up.\u003c\/p\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis setup works best when you can reach the underside of the mounting area to install washers and nylock nuts. Before drilling, confirm the bracket has room to slide and that the motor clears the rub rail and bow hardware in the stowed position.\u003c\/p\u003e\u003cp\u003eIt suits anglers who take the trolling motor off the boat for storage or security, and anyone who wants the option to move between MotorGuide cable-steer and electric-steer setups.\u003c\/p\u003e\u003ch6\u003eWhat's included\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eBase plate\u003c\/li\u003e\n\u003cli\u003eMounting plate (top plate)\u003c\/li\u003e\n\u003cli\u003eHardware pack: 4 x 1\/4-20 x 3 in. mounting bolts, 4 x 1\/4 in. flat washers, 4 x 1\/4 in. rubber washers, 4 x 1\/4-20 nylock nuts\u003c\/li\u003e\n\u003cli\u003eFasteners for top plate: 6 x 1\/4-20 x 7\/16 in. socket head cap screws, 6 x 1\/4-20 x 3\/8 in. Phillips pan head screws\u003c\/li\u003e\n\u003cli\u003eRetaining clip for securing the handle\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eSafety and compliance\u003c\/h6\u003e\u003cp\u003eCalifornia Proposition 65 warning: This product can expose you to chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm. For more information, visit P65Warnings.ca.gov.\u003c\/p\u003e\n\u003cspan itemprop=\"mpn\" hidden\u003e8M0095972\u003c\/span\u003e","brand":"MotorGuide","offers":[{"title":"Default Title","offer_id":53721590923445,"sku":"QBP425717","price":280.48,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1280714_qbp425717.jpg?v=1794118900"},{"product_id":"qbp425377","title":"MotorGuide Xi Series Quick-Release Bracket, For Xi5 Trolling Motors, White Composite Nylon, Stainless Steel Hardware, Security Clasp for Padlock","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe MotorGuide 8M0092063 is a quick-release bracket that lets you remove an Xi series bow-mount trolling motor from the deck without unbolting the base every time.\u003c\/p\u003e\u003cp\u003eIt’s a two-plate setup: one plate stays attached to the trolling motor mount, and the other stays fastened to the boat. When you need the bow clear for storage, trailering, service, or security, you pull the release pin and lift the motor and top plate off as a single unit.\u003c\/p\u003e\u003cp\u003eThis is the white composite version, built to keep the footprint low on the bow. The mounting hardware is stainless steel, which matters when the bracket lives in spray, washdowns, and day-to-day vibration.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eTwo-plate quick-release system so the deck plate can stay installed while the motor removes cleanly.\u003c\/li\u003e\n\u003cli\u003eWhite composite plates with stainless steel mounting hardware.\u003c\/li\u003e\n\u003cli\u003ePin-lock attachment for fast on-and-off at the dock, at the ramp, or in the garage.\u003c\/li\u003e\n\u003cli\u003eLocking clip can be secured with a padlock to help deter theft and keep the release pin from being pulled (padlock not included).\u003c\/li\u003e\n\u003cli\u003eMounting layout uses M6 hardware and a 6 mm drilled hole pattern, which helps when planning backing plates and under-deck access.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis bracket is intended for MotorGuide Xi series bow-mount trolling motor installations. Fit is determined by the mount’s bolt pattern and the available flat surface area on the bow deck, so it’s worth confirming you have room for the bottom plate and access below the deck for washers and locknuts.\u003c\/p\u003e\u003cp\u003eIf your boat has a thin deck, a backing plate underneath helps spread the load and keeps the mount from working the fasteners loose over time. Also confirm the stowed and deployed positions of the motor still clear rails, hatches, and nav lights once the mount height changes slightly.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eInstallation is straightforward: separate the plates, fasten the top plate to the trolling motor mount, then use the bottom plate as the drill template on the deck. Plan the location so you can reach the release pin and locking clip without leaning over the bow.\u003c\/p\u003e\u003cp\u003eA 6 mm drill bit is used for the deck holes, and common hand tools cover the rest. Seal the holes with marine sealant to protect the core and hardware, and recheck fastener torque after the first few trips as the deck bedding settles.\u003c\/p\u003e\u003ch6\u003eWhat’s included\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eTop plate\u003c\/li\u003e\n\u003cli\u003eBottom plate\u003c\/li\u003e\n\u003cli\u003eRelease pin\u003c\/li\u003e\n\u003cli\u003eLocking clip\u003c\/li\u003e\n\u003cli\u003eStainless steel mounting hardware package\u003c\/li\u003e\n\u003cli\u003e5 mm Allen wrench\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eUse on board\u003c\/h6\u003e\u003cp\u003eThis bracket is a good match for anglers who trailer often, store the motor indoors between trips, or want a cleaner bow when the trolling motor is not needed. It also helps when you need quick access for wiring checks, transducer cable routing, or seasonal maintenance without tearing up the deck fasteners.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eRinse the bracket and hardware after saltwater use, especially around the pin and locking clip. A light wipe-down keeps grit from building up where the plates meet, and a quick inspection of the fasteners during routine checks helps prevent loosening from vibration.\u003c\/p\u003e\u003ch6\u003eSafety and compliance\u003c\/h6\u003e\u003cp\u003eWARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.\u003c\/p\u003e\n\u003cspan itemprop=\"mpn\" hidden\u003e8M0092063\u003c\/span\u003e","brand":"MotorGuide","offers":[{"title":"Default Title","offer_id":53721603244213,"sku":"QBP425377","price":134.42,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1280694_qbp425377.jpg?v=1794119037"},{"product_id":"qbp425889","title":"MotorGuide Xi Series Quick-Release Bracket, For Xi3\/Xi5, Black Composite, Low-Profile, Thread-Locking Clamp, Padlock Security Clasp","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe MotorGuide 8M0120717 is a Xi Series quick-release bracket that lets you mount a bow trolling motor and remove it without unbolting the base.\u003c\/p\u003e\u003cp\u003eThe bracket uses a black composite body with a thread-locking clamp style that helps eliminate noise and movement once it is locked down. It is built for MotorGuide Xi3 and Xi5 bow-mount trolling motors, and the low profile with a small footprint helps keep bow space open.\u003c\/p\u003e\u003cp\u003eA security clasp accepts a padlock so the motor can be locked to the bracket when the boat is unattended.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eFits MotorGuide Xi3 and Xi5 bow-mount trolling motors\u003c\/li\u003e\n\u003cli\u003eQuick-release design for fast removal and reinstallation without pulling deck bolts\u003c\/li\u003e\n\u003cli\u003eThread-locking clamp style helps eliminate noise and movement in use\u003c\/li\u003e\n\u003cli\u003eLow profile with a small footprint to save space on the bow\u003c\/li\u003e\n\u003cli\u003eSecurity clasp accepts a padlock for theft deterrence\u003c\/li\u003e\n\u003cli\u003eCast aluminum and stainless steel hardware used in the bracket assembly\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eWhat’s included\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eQuick-release bracket\u003c\/li\u003e\n\u003cli\u003eMounting hardware\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis bracket is intended for the Xi Series platform and is used with MotorGuide Xi3 and Xi5 bow-mount motors. If you are swapping from a different mount or updating an older bracket, confirm the deck area has clearance for the motor to stow and deploy and that the mounting surface is flat and well supported.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003ePlan the location so the motor can stow cleanly without contacting rub rail, cleats, or bow lights. A solid backing plate under the deck helps spread load on thinner fiberglass and reduces flex over time. After mounting, set the clamp tension so the bracket locks down firmly without forcing the mechanism.\u003c\/p\u003e\u003cp\u003eOn saltwater boats or any deck that sees frequent spray, rinsing the bracket after use and keeping the locking surfaces clean helps the quick-release action stay smooth.\u003c\/p\u003e\u003ch6\u003eSafety and compliance\u003c\/h6\u003e\u003cp\u003eWARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.\u003c\/p\u003e\n\u003cspan itemprop=\"mpn\" hidden\u003e8M0120717\u003c\/span\u003e","brand":"MotorGuide","offers":[{"title":"Default Title","offer_id":53721612812469,"sku":"QBP425889","price":134.42,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1280715_qbp425889.jpg?v=1794120255"},{"product_id":"qbp417531","title":"MotorGuide Lowrance 9-Pin HD+ Sonar Adapter Cable, For Tour \u0026 Tour Pro HD+ Motors, For Lowrance HDS Live\/Carbon \u0026 Elite Ti\/Ti2 \u0026 Elite FS, Black 9-Pin Xsonic Port, 83\/200 \u0026 455\/800 kHz, Not for Xi Series Motors","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe MotorGuide 8M4004174 is a Lowrance 9-pin HD+ sonar adapter cable for Tour and Tour Pro HD+ enabled trolling motors, letting your Lowrance display read sonar from the transducer beneath the motor.\u003c\/p\u003e\u003cp\u003eIt supports 83\/200 kHz and 455\/800 kHz sonar frequencies for clear 2D and HD views under the bow, using the black 9-pin Xsonic transducer port found on compatible Lowrance units.\u003c\/p\u003e\u003cp\u003eThis adapter is only for Tour and Tour Pro motors with HD+ sonar support, and it is not compatible with Xi Series motors.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eConnects HD+ sonar from Tour and Tour Pro trolling motors to a Lowrance black 9-pin Xsonic transducer port\u003c\/li\u003e\n\u003cli\u003eSupports 83\/200 kHz and 455\/800 kHz sonar frequencies for 2D and HD views beneath the trolling motor\u003c\/li\u003e\n\u003cli\u003eCompatible with Lowrance HDS and Elite Ti2 displays that use the black 9-pin Xsonic transducer connector\u003c\/li\u003e\n\u003cli\u003eNot compatible with Xi Series motors\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis cable is a match when your boat is rigged with a Tour or Tour Pro motor that is HD+ sonar enabled, and your Lowrance display has the black 9-pin Xsonic transducer port. If your display uses a different transducer connector style, this adapter will not plug in.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eRoute the cable along the trolling motor harness so it can stow and deploy without pulling on the connectors. Keep the connection point where it stays out of standing water, and leave a small drip loop so water does not track into the plug during washdowns or rain.\u003c\/p\u003e\u003cp\u003eAfter installation, set the sonar source on the display to the trolling motor transducer so readings come from beneath the bow rather than another transducer on the boat.\u003c\/p\u003e\u003ch6\u003eOn-board use\u003c\/h6\u003e\u003cp\u003eThis adapter makes sense for anglers running a bow-mounted Lowrance unit who want sonar under the trolling motor for positioning on structure, staying on contour, and watching bottom changes while they work the front deck.\u003c\/p\u003e\u003ch6\u003eSafety note\u003c\/h6\u003e\u003cp\u003eCalifornia Proposition 65 warning: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.\u003c\/p\u003e\n\u003cspan itemprop=\"mpn\" hidden\u003e8M4004174\u003c\/span\u003e","brand":"MotorGuide","offers":[{"title":"Default Title","offer_id":53721614844085,"sku":"QBP417531","price":77.54,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1280689_qbp417531.jpg?v=1794120585"},{"product_id":"qbp417630","title":"MotorGuide Raymarine Axiom HD+ Sonar Adapter Cable, For Tour\/Tour Pro HD+, 2D 83\/200 kHz","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe MotorGuide 8M4004180 is a sonar adapter cable that lets a Raymarine Axiom display read the 2D 83\/200 kHz sonar signal from a MotorGuide Tour or Tour Pro HD+ trolling motor.\u003c\/p\u003e\u003cp\u003eIt is meant for setups where the sonar source is at the bow under the trolling motor, and you want that return on an Axiom (including Axiom Pro) without changing transducers or cutting wiring. This connection is for 2D sonar only, so you will be working with traditional depth and fish-arch views at 83\/200 kHz.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eConnects MotorGuide Tour and Tour Pro HD+ enabled motors to Raymarine Axiom and Axiom Pro sonar inputs\u003c\/li\u003e\n\u003cli\u003e2D sonar only at 83\/200 kHz\u003c\/li\u003e\n\u003cli\u003eInterfaces through the standard MotorGuide blue\/gray 7-pin sonar connector on the motor side\u003c\/li\u003e\n\u003cli\u003eSimple plug connection with no splicing required\u003c\/li\u003e\n\u003cli\u003eNot compatible with MotorGuide Xi Series motors\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis adapter is intended for Tour and Tour Pro models that are HD+ enabled. It is not a match for Xi Series motors, and it is not meant for non HD+ trolling motor sonar setups. On the display side, it is built for the Raymarine Axiom family, including Axiom Pro, for 2D sonar viewing.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eConnect the MotorGuide end to the trolling motor sonar lead, then connect the Raymarine end to the Axiom transducer port. After powering up, select a 2D sonar view and confirm the frequency options are set up for 83\/200 kHz so the unit is looking at the right channel.\u003c\/p\u003e\u003cp\u003eRoute the cable so it can move with the shaft when you deploy and stow the motor. Leave a little slack at the pivot points and secure the run so it will not get pinched by the mount, rub on the steering collar, or snag when the motor is trimmed and strapped down for a run across chop.\u003c\/p\u003e\u003ch6\u003eUse on board\u003c\/h6\u003e\u003cp\u003eThis is a good fit for anglers running a bow-mounted Tour or Tour Pro HD+ who want their Raymarine Axiom at the bow to show bottom tracking and fish targets directly under the trolling motor. It also works well for boats where you want a clean install with the sonar source up front, rather than adding a second transducer and cable run.\u003c\/p\u003e\n\u003cspan itemprop=\"mpn\" hidden\u003e8M4004180\u003c\/span\u003e","brand":"MotorGuide","offers":[{"title":"Default Title","offer_id":53721616842933,"sku":"QBP417630","price":93.04,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1280693_qbp417630.jpg?v=1794120809"}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/collections\/56b3da80-fd50-5304-8618-d0747a49dd15.webp?v=1794118086","url":"https:\/\/www.qualityboatparts.com\/collections\/cat-trolling-motor-accessories.oembed","provider":"Quality Boat Parts","version":"1.0","type":"link"}