{"title":"Fuel Systems","description":"","products":[{"product_id":"qbp906682","title":"Attwood Marine Round Vented Gas Deck Fill, Angled, Black Plastic, 1-1\/2 in Fill Hose, 5\/8 in Vent Hose","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Attwood Marine 99201GS1 is a vented gas deck fill with a round cap, an angled plastic neck, and hose connections for 1-1\/2 in. fuel fill hose and 5\/8 in. vent hose. It uses a cap made from stainless steel at deck level and an integrated vent arrangement inside the fill body.\u003c\/p\u003e\u003cp\u003eThis part is marked for gasoline service and uses a built-in vent path rather than relying on a separate deck vent fitting. For replacement work, the round cap measures 85 mm, with a 54 mm neck cutout and a 20 mm vent cutout. Installation uses four #8 screws.\u003c\/p\u003e\u003cp\u003eThis version belongs to Attwood's international gasoline deck fill range and is not for U.S. or Canada gasoline applications. That matters when you are matching it to the boat's fuel-system layout and local compliance requirements.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eFits standard 1-1\/2 in. fuel fill hose and 5\/8 in. vent hose.\u003c\/li\u003e\n\u003cli\u003eAngled neck helps where the hose run below deck does not line up straight under the fill point.\u003c\/li\u003e\n\u003cli\u003eWaterproof screen in the vent path blocks water from entering through the fill while the tank continues to vent.\u003c\/li\u003e\n\u003cli\u003eIntegral vent includes a flame arrestor and anti-surge feature inside the fill assembly.\u003c\/li\u003e\n\u003cli\u003eRound gasoline cap uses the fuel symbol on top and includes a beaded retaining chain and deck plate key.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis deck fill suits boats already rigged for 38 mm fill hose and 16 mm vent hose, especially when the original hardware used a round fill with the vent built into the filler body. It is a practical match for replacement work on runabouts, center consoles, small cruisers, and sailboats that carry gasoline and need an angled hose entry below deck.\u003c\/p\u003e\u003cp\u003eBefore ordering, check the hose sizes, the deck opening, the screw pattern, and the clearance needed for the angled neck and vent connection. On boats with tight access under side decks or coamings, the angled body can make hose routing easier than a straight fill.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eBecause the vent is part of the deck fill, the hose layout below deck needs to stay clean and unrestricted. The fill hose should run to the tank without a sharp pinch point, and the vent hose needs enough rise and space to avoid slow fueling or splash-back at the nozzle.\u003c\/p\u003e\u003cp\u003eThe round cap format keeps the top-side footprint familiar for many replacement jobs, while the stainless cap gives you a hard wearing surface at the deck. If you are replacing an older fill, it is worth checking that the cap can open freely and that the retaining chain has room to hang clear when fueling.\u003c\/p\u003e\n\u003cspan itemprop=\"mpn\" hidden\u003e99201GS1\u003c\/span\u003e","brand":"Attwood Marine","offers":[{"title":"Default Title","offer_id":53721526862005,"sku":"QBP906682","price":38.61,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1322205_qbp906682.webp?v=1794116280"},{"product_id":"qbp906722","title":"Attwood Marine Plastic Waste Deck Fill, For 38mm Hose, Scalloped Stainless Steel Cap","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Attwood Marine 99202WS1 is a waste deck fill with a plastic neck and a stainless steel cap for boats that use a 38 mm sanitation hose. It is a non-vented fitting, uses a 54 mm deck cutout, and has an 85 mm cap diameter, so the key fit checks are hose size, deck opening, and the flange footprint on the surface of the deck.\u003c\/p\u003e\u003cp\u003eThis fitting is for waste service, not fuel or freshwater, and the cap is marked accordingly to help keep deck fills clearly identified. That matters on boats with more than one fill point, especially when fuel, water, and sanitation access points are grouped in the same area.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eWaste deck fill for sanitation pump-out systems.\u003c\/li\u003e\n\u003cli\u003e38 mm hose connection size for matching existing waste hose runs.\u003c\/li\u003e\n\u003cli\u003e54 mm deck cutout requirement for replacement planning or new installation.\u003c\/li\u003e\n\u003cli\u003e85 mm cap diameter for checking flange coverage at the deck surface.\u003c\/li\u003e\n\u003cli\u003ePlastic neck with a stainless steel cap.\u003c\/li\u003e\n\u003cli\u003eNon-vented body for systems where tank venting is handled through a separate vent line.\u003c\/li\u003e\n\u003cli\u003eWaste marking on the cap helps avoid confusion with fuel or water fills.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and fit\u003c\/h6\u003e\u003cp\u003eOn a replacement job, the practical checks are straightforward: confirm the hose is 38 mm, measure the existing deck opening, and make sure the 85 mm cap will sit cleanly over the area on deck. It also helps to check clearance below the mounting point so the hose can run without a sharp bend right under the fitting.\u003c\/p\u003e\u003cp\u003eThis is a good match for cruisers, fishing boats, and sailboats with an onboard head and holding tank where you need a clearly marked waste pump-out point on deck. If your boat already has a separate tank vent and you are matching a non-vented waste fill in this size, this fitting lines up with that type of setup.\u003c\/p\u003e\n\u003cspan itemprop=\"mpn\" hidden\u003e99202WS1\u003c\/span\u003e","brand":"Attwood Marine","offers":[{"title":"Default Title","offer_id":53721529122997,"sku":"QBP906722","price":66.4,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1322207_qbp906722.webp?v=1794116576"},{"product_id":"qbp456707","title":"Attwood Marine 90 Degree P-Trap Fuel Tank Vent Replacement Cover","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Attwood Marine 90° P-Trap Fuel Tank Vent is a replacement cover range for Attwood P-Trap fuel tank vents used in boat fuel venting systems. These covers are meant for existing Attwood vent installations where the exterior cap or trim has been damaged, weathered, or lost, while the vent body and hose connection remain serviceable.\u003c\/p\u003e\u003cp\u003eThe matching P-Trap vent family is made for 5\/8 in. I.D. fuel vent hose and is specified to meet ABYC standard. The P-Trap layout helps keep water from reaching the fuel tank vent line during normal sea conditions and washdowns, while still allowing air to move as the tank is filled.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eReplacement cover range for Attwood 90° P-Trap fuel tank vent installations.\u003c\/li\u003e\n\u003cli\u003eHelps restore the exterior vent cover without replacing the full vent assembly when the existing body is in good condition.\u003c\/li\u003e\n\u003cli\u003eSupports the P-Trap vent layout that allows tank ventilation during fueling while helping reduce water entry through the vent path.\u003c\/li\u003e\n\u003cli\u003eAssociated with Attwood P-Trap vents for 5\/8 in. I.D. fuel vent hose.\u003c\/li\u003e\n\u003cli\u003eWorks with the vent family specified to meet ABYC standard.\u003c\/li\u003e\n\u003cli\u003eAvailable in configurations for different existing Attwood vent cover styles.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eVariants\u003c\/h6\u003e\u003cp\u003eThis product is offered in two replacement cover configurations. The correct choice depends on the Attwood vent already installed on the boat, so the existing vent body, cover shape, and visible trim should be checked before ordering.\u003c\/p\u003e\u003cp\u003eThe two listings separate the replacement by mount style and by the original Attwood vent model. Part 911526-1 is tied to the 1670 P-Trap vent, while part 911528-1 is tied to the 66419 P-Trap vent with stainless steel trim cover.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e911526-1, Mount Style Standard: black replacement cover for the Attwood 1670 P-Trap fuel tank vent. This suits installations where the existing black exterior cover needs to be renewed while the standard vent body remains in place.\u003c\/li\u003e\n\u003cli\u003e911528-1, Mount Style Flush: stainless steel replacement cover kit associated with the Attwood 66419 P-Trap fuel tank vent. This keeps the stainless trim appearance at the vent opening and should be matched to the existing Attwood vent body before installation.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eBecause these are replacement covers, fit is driven by the existing Attwood vent model rather than by hose size alone. Before installation, compare the old cover and vent body with the selected replacement part, and confirm that the fuel vent assembly itself is not cracked, loose, or damaged.\u003c\/p\u003e\u003cp\u003eFor boats used in saltwater, exposed slips, or washdown-heavy fishing use, the vent cover is a small part that still matters. A missing or damaged cover can leave the vent opening more exposed, so replacement should be handled before regular spray, rain, or deck washdowns become a problem.\u003c\/p\u003e\u003ch6\u003eInstallation and care\u003c\/h6\u003e\u003cp\u003eInstall the replacement cover with the fuel system area well ventilated and away from ignition sources. If the old cover failed because of impact, corrosion around surrounding hardware, or movement in the vent body, inspect the hose, clamps, and mounting area before putting the boat back into service.\u003c\/p\u003e\u003cp\u003eRoutine cleaning with fresh water helps remove salt and deck grime from the vent area. Avoid sealing or coating over the vent opening, since the tank still needs clear air movement during fueling and normal operation.\u003c\/p\u003e\n\u003cspan itemprop=\"mpn\" hidden\u003e911526-1\u003c\/span\u003e\n\u003cspan itemprop=\"mpn\" hidden\u003e911528-1\u003c\/span\u003e","brand":"Attwood Marine","offers":[{"title":"Standard","offer_id":53721603539125,"sku":"QBP456707-V1","price":7.74,"currency_code":"USD","in_stock":false},{"title":"Flush","offer_id":53721603571893,"sku":"QBP456707-V2","price":25.35,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1327625_qbp456707.webp?v=1794119129"},{"product_id":"qbp826359","title":"Attwood Marine Cowl Vent, 3 in Ventilation Hose, Chrome-Plated ZAMAK","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Attwood Marine 1364A1 is a deck-mount cowl vent for standard 3 inch ventilation hose. It can be set up as either an intake or an exhaust, so it works where you need passive airflow through an enclosed space rather than a powered blower.\u003c\/p\u003e\u003cp\u003eThis vent uses a flexible flange attachment that connects to the hose below deck, then accepts the vent head once the base is mounted. The vent body is die-cast ZAMAK with a chrome finish, and the flange is black plastic. For the installation shown in the instructions, the deck opening is 3-1\/2 inches when a nylon wire tie is used as the hose clamp.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eFits any standard 3 inch ventilation hose\u003c\/li\u003e\n\u003cli\u003eCan be used for either intake or exhaust airflow\u003c\/li\u003e\n\u003cli\u003eDie-cast ZAMAK vent head with chrome finish\u003c\/li\u003e\n\u003cli\u003eBlack plastic flange attaches the hose below deck\u003c\/li\u003e\n\u003cli\u003eFlexible flange-and-head design allows the vent head to snap onto the mounted base\u003c\/li\u003e\n\u003cli\u003eInstallation uses three #8 countersunk screws and a hose clamp or 15 inch nylon wire tie\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and fit\u003c\/h6\u003e\u003cp\u003eThis is a straightforward replacement part when your boat already uses a 3 inch vent hose and a deck cowl in this style. The base is used as the drilling template, the hose slides up through the deck cutout and over the flange, and the vent head attaches after the base is fastened down. It is worth checking the deck opening before ordering, since the stated 3-1\/2 inch hole size is tied to the clamp method used during installation.\u003c\/p\u003e\u003ch6\u003eUse on board\u003c\/h6\u003e\u003cp\u003eThis vent suits refit work on boats that need passive deck ventilation through a hose-fed run below deck. It makes sense for owners replacing an older cowl vent on a sailboat, runabout, or classic fiberglass boat where the existing hose size and mounting style need to stay the same.\u003c\/p\u003e\n\u003cspan itemprop=\"mpn\" hidden\u003e1364A1\u003c\/span\u003e","brand":"Attwood Marine","offers":[{"title":"Default Title","offer_id":53721615302837,"sku":"QBP826359","price":39.0,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1322187_qbp826359.webp?v=1794120696"}],"url":"https:\/\/www.qualityboatparts.com\/collections\/cat-fuel-systems.oembed","provider":"Quality Boat Parts","version":"1.0","type":"link"}