{"title":"Boat Trailering","description":"","products":[{"product_id":"qbp629688","title":"MotorGuide Trolling Motor Tie-Down Strap, For Gator Mounts, 2 x 28 in","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe MotorGuide MGA507A1 is a hook-and-loop tie down strap that secures a stowed trolling motor to its mount to help stop bounce during trailering and on rough-water runs. It measures 2 in wide by 28 in long, giving you enough wrap to cinch the shaft down without having to fight with knots or ratchets.\u003c\/p\u003e\u003cp\u003eOn a boat, this strap is used as a secondary hold-down after you stow the motor. It lays over the shaft and fastens back onto itself, keeping the motor from lifting or chattering against the bracket when the hull is taking waves, wakes, or potholes on the road.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e2 in x 28 in strap size for a secure wrap over the trolling motor shaft\u003c\/li\u003e\n\u003cli\u003eHook-and-loop closure for quick tightening, removal, and re-tensioning at the ramp\u003c\/li\u003e\n\u003cli\u003eMade to work with MotorGuide Gator mount setups, including common X3 and X5 applications\u003c\/li\u003e\n\u003cli\u003eHelps reduce stow bounce that can scuff decks, stress brackets, and wear mount hardware\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eWith the trolling motor fully stowed, run the strap over the shaft and anchor it down to the mount base, then pull it snug and press the hook-and-loop surfaces together. Set it tight enough that the shaft cannot hop in chop, but not so tight that it twists the shaft sideways or interferes with the latch mechanism. After the first run, recheck tension and adjust as the strap beds in.\u003c\/p\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis strap is intended for MotorGuide trolling motors that use a Gator-style mount. If your mount has a clear strap path over the shaft and a solid point on the base to secure to, it will function as a straightforward hold-down. For the cleanest fit, confirm you have room to route the strap without pinching cables, steering linkages, or lift-assist components.\u003c\/p\u003e\u003ch6\u003eUse on board\u003c\/h6\u003e\u003cp\u003eIt is a practical add-on for anglers who trailer frequently, run big water, or make long moves between spots where the bow takes repeated impacts. It also helps when the boat is stored on a lift or at the dock and you want the stowed motor held down against wind-driven movement.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eRinse the strap after saltwater use, especially around the hook-and-loop area where grit can reduce grip. Inspect the strap and closure periodically for fraying or debris buildup, and replace it if the fastening surfaces no longer hold firmly.\u003c\/p\u003e\n\u003cspan itemprop=\"mpn\" hidden\u003eMGA507A1\u003c\/span\u003e","brand":"MotorGuide","offers":[{"title":"Default Title","offer_id":53721528336565,"sku":"QBP629688","price":20.96,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1280727_qbp629688.jpg?v=1794116441"},{"product_id":"qbp262977","title":"Attwood Marine Cover Support Bow Sockets, Angled, ZAMAK, Pair","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Attwood Marine 10796-3 is a pair of angled slat sockets for mounting boat cover support bows made from fiberglass, aluminum, or wood. The sockets are made from ZAMAK, installation uses #10 fasteners, and each socket sits against a plastic backing plate that helps protect the boat finish at the mounting point.\u003c\/p\u003e\u003cp\u003eThis hardware gives a cover support bow a fixed place to land so the bow can hold shape under a mooring or storage cover. When an old socket is cracked, loose, or rubbing the gelcoat, replacing it can help the bow sit correctly again and keep the cover from sagging across the cockpit or bow seating area.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eAngled socket shape for boat cover support bows\u003c\/li\u003e\n\u003cli\u003eFits fiberglass, aluminum, and wood bows\u003c\/li\u003e\n\u003cli\u003eZAMAK construction with plastic backing plate to reduce contact against the boat finish\u003c\/li\u003e\n\u003cli\u003eSold as a pair for two-point bow mounting\u003c\/li\u003e\n\u003cli\u003eInstallation uses #10 fasteners\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThese sockets are for cover-support hardware, not for seat mounts, rail fittings, or bimini frame hardware. Fit depends on the bow material and the shape of the bow end, so it helps to match the angled socket style to the hardware already on the boat before drilling new holes.\u003c\/p\u003e\u003cp\u003eBecause the socket accepts fiberglass, aluminum, and wood bows, it suits many runabouts, fishing boats, and older trailer boats that use a removable support bow under the cover. It is a sensible replacement when the bow itself is still usable and the mounting sockets are the worn part.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eMount the plastic backing plate against the finished surface so the socket does not rub directly on gelcoat or paint. Keep the socket aligned with the natural angle of the support bow so the bow seats fully without side load on the fasteners.\u003c\/p\u003e\u003cp\u003eBefore installation, check the mounting area for enlarged holes, surface cracks, or a weak substrate left by loose cover hardware. A sound mounting surface and correctly sized #10 fasteners help the socket stay in place as the boat moves on the trailer, at the dock, or under a cover in storage.\u003c\/p\u003e\n\u003cspan itemprop=\"mpn\" hidden\u003e10796-3\u003c\/span\u003e","brand":"Attwood Marine","offers":[{"title":"Default Title","offer_id":53721611894965,"sku":"QBP262977","price":8.96,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1322085_qbp262977.webp?v=1794120132"}],"url":"https:\/\/www.qualityboatparts.com\/collections\/cat-boat-trailering.oembed","provider":"Quality Boat Parts","version":"1.0","type":"link"}