{"title":"Audio Accessories","description":"","products":[{"product_id":"qbp346091","title":"JL Audio MTPOD-M100-CL Tweeter Mounting Pods, For M-Series Component Tweeters, Clear Anodized, Billet Aluminum, Surface or Deck Mount, Pair","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe JL Audio 010-13722-00 is a pair of billet aluminum tweeter mounting pods with a clear anodized finish for surface or deck installs on boats.\u003c\/p\u003e\u003cp\u003eEach pod is machined from a single piece of aluminum and uses a slightly up-angled base, which helps aim the highs toward the cockpit instead of straight across the deck. A dedicated wire pathway lets you route the tweeter leads out of sight so the install stays clean.\u003c\/p\u003e\u003cp\u003eFor layout and clearance, each pod measures 2.38 in (60 mm) in diameter with a mounted height of 2.50 in (64 mm) and a mounted depth of about 3.55 in (90 mm). Tweeters are not included.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eBillet aluminum pod with a clear anodized finish that resists corrosion in a saltwater environment\u003c\/li\u003e\n\u003cli\u003eSurface or deck mounting style for installs where a flush mount is not practical\u003c\/li\u003e\n\u003cli\u003eSlightly up-angled base to help spread high frequencies across seating areas\u003c\/li\u003e\n\u003cli\u003eInternal pathway to route and conceal tweeter wiring\u003c\/li\u003e\n\u003cli\u003eMade to house Legacy JL Audio M-Series component tweeters (sold separately)\u003c\/li\u003e\n\u003cli\u003ePod dimensions: 2.38 in (60 mm) diameter, 2.50 in (64 mm) mounted height, 3.55 in (90 mm) mounted depth\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eWhat's included\u003c\/h6\u003e\u003cul\u003e\u003cli\u003eTwo tweeter mounting pods (one pair)\u003c\/li\u003e\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThese pods are sized for Legacy JL Audio M-Series component tweeters. If you are pairing them with a different series or a different brand, confirm the tweeter body and flange dimensions before drilling so the tweeter seats correctly in the pod.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003ePick a mounting spot with enough backside clearance for the 3.55 in (90 mm) mounted depth and a protected route for the speaker wire. On thin fiberglass, aluminum, or composite panels, backing washers or a backing plate help keep the mount solid under vibration.\u003c\/p\u003e\u003cp\u003eAfter drilling, seal exposed core material and fastener holes to keep water out of the laminate. Route audio wiring away from high-current power runs and ignition components to help avoid noise in the system.\u003c\/p\u003e\u003ch6\u003eUse on board\u003c\/h6\u003e\u003cp\u003eCommon mounting locations include a T-top, hardtop, radar arch, wake tower, and under-gunwale areas where you want the highs aimed toward the cockpit. This is a good match for boats that get regular spray and need a clean, sturdy surface-mount option for component tweeters.\u003c\/p\u003e\n\u003cspan itemprop=\"mpn\" hidden\u003e010-13722-00\u003c\/span\u003e","brand":"JL Audio","offers":[{"title":"Default Title","offer_id":53721537478837,"sku":"QBP346091","price":193.0,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1281151_qbp346091.jpg?v=1794117128"},{"product_id":"qbp389913","title":"JL Audio XMD-PCS30A-1-L12 Single-Amplifier Power Connection Kit, 9 AWG, 12V, 30A MAXI Fuse","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe JL Audio 010-13400-00 is a 12-volt power and ground wiring kit for a single marine audio amplifier, sized for installs where the amplifier sits within 12 ft (3.7 m) of the battery and up to 30 A.\u003c\/p\u003e\u003cp\u003eIt uses 9 AWG tinned, oxygen-free copper conductors with ABYC-standard color coding, so the positive and negative runs stay easy to identify once everything is routed through rigging tubes and consoles. A 30 A MAXI fuse and fuse holder are included to protect the main feed, along with a separate 16 AWG remote turn-on lead for the amp trigger signal.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eFor 12V DC amplifier wiring runs up to 12 ft (3.7 m) from the battery to the amplifier location\u003c\/li\u003e\n\u003cli\u003e9 AWG tinned, oxygen-free copper power and ground conductors for corrosion resistance in wet lockers and salt-air environments\u003c\/li\u003e\n\u003cli\u003e30 A maximum system rating, with a 30 A MAXI fuse and fuse holder included for primary circuit protection\u003c\/li\u003e\n\u003cli\u003eABYC-standard wire colors to keep polarity clear during installation and future troubleshooting\u003c\/li\u003e\n\u003cli\u003eIncludes an 18 ft (5.5 m) 16 AWG remote turn-on wire for typical helm-to-amp routing\u003c\/li\u003e\n\u003cli\u003eMix of pre-terminated ring-end leads and unterminated wire length to fit different battery switch layouts and mounting distances\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eRoute the power and ground runs like any other primary DC feed on a boat: keep them supported, protect them from chafe where they pass through bulkheads, and avoid hot spots such as engine compartments and heater ducts unless the wiring is properly shielded and secured. Leave enough service loop at the amplifier so you can pull it for service without stressing the terminals.\u003c\/p\u003e\u003cp\u003eMount the fuse holder on the positive feed as close to the battery connection point as practical, then finish terminations with marine-grade crimping and sealing practices suited for the bilge and console environment. If the boat is on a 24V system, this kit belongs on a properly protected 12V feed used for the audio system.\u003c\/p\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis kit matches 12V marine audio installations that stay within the stated distance and current limit. If your amplifier draw is higher than 30 A, or the run to the battery is longer than 12 ft (3.7 m), plan for heavier-gauge conductors and protection sized to the full load and routing distance.\u003c\/p\u003e\u003ch6\u003eUse cases on board\u003c\/h6\u003e\u003cp\u003eThis is a practical match for center consoles, runabouts, towboats, and pontoons where the amplifier is mounted in a console, helm area, or inboard storage space near the battery compartment. It also suits refits where the existing audio wiring needs to be cleaned up with consistent color coding and proper primary fuse protection.\u003c\/p\u003e\u003ch6\u003eWhat's included\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eRed 9 AWG tinned power wire with one power ring, 2 ft (0.6 m)\u003c\/li\u003e\n\u003cli\u003eRed 9 AWG tinned power wire, unterminated, 10 ft (3 m)\u003c\/li\u003e\n\u003cli\u003eYellow 9 AWG tinned ground wire with one power ring, 12 ft (3.7 m)\u003c\/li\u003e\n\u003cli\u003eBlue 16 AWG remote turn-on wire, 18 ft (5.5 m)\u003c\/li\u003e\n\u003cli\u003e30 A MAXI fuse and fuse holder (XD-MFBW-MAXI)\u003c\/li\u003e\n\u003cli\u003eFour 4-inch wire ties\u003c\/li\u003e\n\u003cli\u003e4 mm hex wrench\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cspan itemprop=\"mpn\" hidden\u003e010-13400-00\u003c\/span\u003e","brand":"Garmin","offers":[{"title":"Default Title","offer_id":53721538494645,"sku":"QBP389913","price":181.71,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1281205_qbp389913.jpg?v=1794117221"},{"product_id":"qbp951093","title":"Plash - WetSounds 10\" (SINGLE) (Powered Sub Only) LED Speaker Ring - RGB, 12V, IP67 (SPKR-WS10)","description":"\u003cp\u003eIntroducing the Plash LED Speaker Rings - the perfect addition to your marine audio system! These innovative rings are designed to enhance the visual appeal of your boat's sound system while providing high-quality sound output.\u003c\/p\u003e\n\u003cp\u003eEquipped with RGB LED lights, the Plash Speaker Rings can add a vibrant burst of color to your marine audio experience. With the ability to choose from a wide range of colors and lighting effects, you can easily customize the ambiance of your boat's sound system to fit any mood or occasion.\u003c\/p\u003e\n\u003cp\u003eNot only do these speaker rings look great, but they are also built to last. The Plash Speaker Rings are rated IP67, meaning they are fully waterproof and can withstand exposure to saltwater, rain, and other harsh marine environments. Whether you're out on the open ocean or cruising on a lake, you can trust the Plash Speaker Rings to deliver high-quality sound and lighting performance.\u003c\/p\u003e\n\u003cp\u003eWith a 12V power supply, the Plash Speaker Rings are easy to install and integrate seamlessly with your boat's existing audio system. Simply connect the wires and you're ready to go! Whether you're a seasoned boater or just starting out, the Plash LED Speaker Rings are a must-have accessory for any marine audio system.\u003c\/p\u003e\n\u003cspan itemprop=\"mpn\" hidden\u003eSPKR-WS10\u003c\/span\u003e","brand":"Plash","offers":[{"title":"Default Title","offer_id":53721615073461,"sku":"QBP951093","price":104.95,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/0371557_qbp063782_jpeg.jpg?v=1794120626"}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/collections\/8e0e4b4a-735a-5137-86e0-d335d0bc0a98.webp?v=1794118120","url":"https:\/\/www.qualityboatparts.com\/collections\/cat-audio-accessories.oembed","provider":"Quality Boat Parts","version":"1.0","type":"link"}