{"title":"Vimar","description":"","products":[{"product_id":"qbp678969","title":"Vimar Rectangular Flush Mounting Box, 6-7 Module, For Masonry Walls, 174 x 59 mm, 50 mm Internal Depth, Black","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Vimar VM71306.AU is a flush-mount box with a rectangular 6 to 7-module format, finished in black, used behind device supports and cover plates for a clean recessed installation. The body measures 174 mm wide by 59 mm tall and gives about 50 mm of internal depth for wiring.\u003c\/p\u003e\u003cp\u003eIt has nine break-out inlets with knockouts sized for 20 mm or 25 mm conduit, so you can route cables neatly through a bulkhead or cabinet side and keep strain off the terminals. Switching equipment mounts by screws, and the box is supplied without screws and without a cover.\u003c\/p\u003e\u003cp\u003eThe housing is plastic that is halogen-free and tested to a 960 C glow-wire rating. The box carries an IP00 rating, so it is not a watertight enclosure and belongs in protected interior locations on board, behind the finished plate.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eUnified 6 to 7-module recessed box format for wall-plate installations\u003c\/li\u003e\n\u003cli\u003e174 mm x 59 mm body size with about 50 mm internal depth for wiring space\u003c\/li\u003e\n\u003cli\u003eNine break-out cable entries with knockouts for 20 mm or 25 mm conduit\u003c\/li\u003e\n\u003cli\u003eRear entry option for bringing wiring straight in from behind the panel\u003c\/li\u003e\n\u003cli\u003eProvision for a dividing screen via the internal rack (divider sold separately)\u003c\/li\u003e\n\u003cli\u003eConnectable box body for building multi-gang runs with coupling accessories\u003c\/li\u003e\n\u003cli\u003eSupport screw lugs have zinc plating to help keep threads clear during installation\u003c\/li\u003e\n\u003cli\u003eHalogen-free plastic with a 960 C glow-wire test rating; IP00 enclosure rating\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis box is intended for installations based on the Italian 6 to 7-module standard. Confirm your device support and cover plate are sized for a 6M or 7M opening and that your mounting surface has enough depth behind it to accommodate the box and cable bend radius.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eLay out cable routing before setting the box, then open only the knockouts you need to keep the fit tight around conduit or looms. When wiring comes from behind, using the rear entry helps reduce crowding at the sides. Since devices mount by screws, make sure the correct screws are available for the support you are installing.\u003c\/p\u003e\u003ch6\u003eUse on board\u003c\/h6\u003e\u003cp\u003eThis style of recessed back box is a good match for cabins, enclosed consoles, and interior joinery where switches and outlets need a flush finish and protection from bumps. Keep it out of areas exposed to washdowns or spray, and rely on the fitted device and cover plate for the finished front surface.\u003c\/p\u003e\n\u003cspan itemprop=\"mpn\" hidden\u003eVM71306.AU\u003c\/span\u003e","brand":"Vimar","offers":[{"title":"Default Title","offer_id":53721538658485,"sku":"QBP678969","price":19.34,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/0368804_qbp678969_jpeg.jpg?v=1794117238"},{"product_id":"qbp037511","title":"Vimar 5-Module Flush Mounting Box, For Masonry, Glow Wire 960C, Black","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Vimar VM71305.AU is a 5-module flush mounting box for recessed installations where you want Vimar electrical fittings to sit cleanly in a solid wall or bulkhead. The body measures 144 mm wide by 59 mm tall, with a 50 mm inner depth, which gives you working room for wiring behind a 5-module frame and faceplate.\u003c\/p\u003e\u003cp\u003eIt is made from halogen-free plastic and has a Glow Wire rating of 960 °C. Cable entry is handled through break-out openings sized for 20 mm and 25 mm conduit, with rear entry available as well, so you can route wiring the way your boat is built rather than forcing tight bends.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e5-module flush box for Vimar mounting frames and faceplates\u003c\/li\u003e\n\u003cli\u003eBox size: 144 x 59 mm footprint with 50 mm inner depth\u003c\/li\u003e\n\u003cli\u003eGlow Wire 960 °C rating\u003c\/li\u003e\n\u003cli\u003e16 break-out inlets, including rear entry; accepts 20 mm and 25 mm conduit\u003c\/li\u003e\n\u003cli\u003eCouplable format for side-by-side multi-gang runs\u003c\/li\u003e\n\u003cli\u003eIP00 enclosure; any sealing depends on the devices and front plate used\u003c\/li\u003e\n\u003cli\u003eSupplied without mounting screws\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis is a 5-module format box, so match it with a 5-module Vimar support frame and the correct series faceplate for the switches, sockets, or connectors you are installing. The box is specified for flush mounting in masonry and other solid walls; for thin liners or hollow panels, a different box style is typically used.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eConfirm you have enough depth behind the finish surface for the box and for the wiring to land without being forced against the back. On boats, this type of box is commonly set into a solid timber, fiberglass, or composite bulkhead and secured so it stays tight under vibration.\u003c\/p\u003e\u003cp\u003eKnock out only the entries you need and keep the remaining openings intact. After pulling conductors through the chosen 20 mm or 25 mm entries, leave slack for servicing and make sure devices can be screwed down without pinching insulation.\u003c\/p\u003e\u003ch6\u003eUse notes on board\u003c\/h6\u003e\u003cp\u003eBecause the enclosure itself is IP00, it is best placed in dry interior areas unless the front devices and faceplate provide the protection needed for that location. It suits cabins, galleys, and nav stations where you want wiring contained behind the panel with a clean flush finish.\u003c\/p\u003e\n\u003cspan itemprop=\"mpn\" hidden\u003eVM71305.AU\u003c\/span\u003e","brand":"Vimar","offers":[{"title":"Default Title","offer_id":53721540853941,"sku":"QBP037511","price":16.22,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/0368803_qbp037511_jpeg.jpg?v=1794117446"},{"product_id":"qbp055855","title":"Vimar 4M Flush Mounting Box, Masonry Walls, Black, Glow Wire 960C","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Vimar VM71304.AU is a 4-module flush mounting box in black plastic for recessed installation, with a 121 x 59 mm footprint and a 50 mm inner depth. It gives you a clean back box for modular devices while leaving room for wiring behind the support frame.\u003c\/p\u003e\u003cp\u003eOn board, this style of box is most often used behind interior panels and bulkheads for switch banks, outlets, or control points in cabins, galleys, and navigation areas where the backside stays dry and protected. With an IP00 protection level, it is not meant for locations exposed to spray, washdowns, or condensation that can drip onto the wiring.\u003c\/p\u003e\u003cp\u003eThe body is halogen-free and carries a Glow Wire 960°C rating. Break-out openings help with cable entry and routing so you can keep conductors supported and serviceable once the front devices are installed.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e4-module recessed box format with 121 x 59 mm face footprint and 50 mm inner depth\u003c\/li\u003e\n\u003cli\u003eGlow Wire flammability rating of 960°C\u003c\/li\u003e\n\u003cli\u003eHalogen-free plastic body in black\u003c\/li\u003e\n\u003cli\u003eBreak-out openings for feed-throughs, including 20 mm and 25 mm conduit entries\u003c\/li\u003e\n\u003cli\u003eRack provision for fixing a dividing screen to separate wiring runs\u003c\/li\u003e\n\u003cli\u003eZinc-plated support-screw lugs to help keep threads clear during installation\u003c\/li\u003e\n\u003cli\u003eIP00 protection level for dry, protected mounting locations\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis box is built around a 4-module layout and is intended to house modular device inserts that match this footprint. Confirm the device support frame and cover plate you are using are intended for a 4-module recessed box, and check that your mounting surface allows the full depth behind the finished face.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eThe box is intended for recessed installation and is commonly set so the front edge finishes flush with the wall or panel face. Plan cable routing before the box is closed up, keep enough slack for servicing, and avoid packing the cavity so tightly that device terminals are under strain when the inserts are fastened.\u003c\/p\u003e\u003ch6\u003eOn-board use notes\u003c\/h6\u003e\u003cp\u003eFor marine installs, treat this as an interior back box: keep it out of wet lockers, exposed cockpits, and areas where washdowns can reach the wiring. It is a good match for refits where you want a tidy, modular control point in protected living spaces or behind a sheltered helm panel, and you already have Vimar-format devices that fit a 4-module recessed box.\u003c\/p\u003e\n\u003cspan itemprop=\"mpn\" hidden\u003eVM71304.AU\u003c\/span\u003e","brand":"Vimar","offers":[{"title":"Default Title","offer_id":53721541345461,"sku":"QBP055855","price":11.02,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/0370670_qbp055855_jpeg.jpg?v=1794117574"},{"product_id":"qbp600575","title":"Vimar Arke Axial 1-Way Switch, Single Pole, 16AX, 250V AC, Illuminable, 2-Module, Grey","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Vimar VM19101 is a 1-pole, 1-way axial switch mechanism for the Arké modular system, rated 16 AX at 250 V~ and suitable for loads up to 200 W for self-ballasted lamps.\u003c\/p\u003e\u003cp\u003eIt takes up two modules in a Vimar Arké frame and sits behind your chosen cover plate to build consistent switch banks around the boat, such as at a cabin entry panel, at the helm console, or in a galley switch cluster. The axial rocker action feels familiar in use, and the button is replaceable, which helps when you are matching surrounding devices or updating legends during a refit.\u003c\/p\u003e\u003cp\u003eThis is a standard in-panel switching mechanism, so plan to mount it in a protected location inside an electrical panel or enclosure, away from direct spray and routine washdowns.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e1P\/1-way (on\/off) switching for controlling a single circuit from one location\u003c\/li\u003e\n\u003cli\u003e16 AX, 250 V~ rating; supports up to 200 W self-ballasted lamps\u003c\/li\u003e\n\u003cli\u003e2-module format to lay out multi-gang panels within the Vimar Arké modular system\u003c\/li\u003e\n\u003cli\u003eLightable mechanism so a compatible locator or indicator light can be added when needed\u003c\/li\u003e\n\u003cli\u003eReplaceable rocker button for cleaner labeling and a consistent look across the panel\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eThis mechanism installs into a Vimar Arké mounting frame and back box like other Arké devices, then is finished with a matching cover plate. Wiring is the standard 1-way arrangement (line in and switched line out); verify conductor sizing and overcurrent protection match the circuit and your vessel’s electrical practices.\u003c\/p\u003e\u003cp\u003eWhen planning a multi-device panel, keep module count in mind: this switch uses two modules, so it pairs cleanly with other 2-module Arké components in shared cover plates.\u003c\/p\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eA good match for boats already built out with Vimar Arké, or for new interior panels where you want the same frames, devices, and cover plates throughout. If you need switching in an exposed exterior location, use an appropriate sealed switch or relocate the device to a protected panel.\u003c\/p\u003e\u003ch6\u003eUse on board\u003c\/h6\u003e\u003cp\u003eCommon uses include interior lighting circuits, ventilation controls, and other on\/off loads where you want a tidy, flush panel. The illumination capability is handy on night passages when you want to find the switch quickly without turning on overhead lights.\u003c\/p\u003e\n\u003cspan itemprop=\"mpn\" hidden\u003eVM19101\u003c\/span\u003e","brand":"Vimar","offers":[{"title":"Default Title","offer_id":53721558909109,"sku":"QBP600575","price":9.5,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1281427_qbp600575_jpeg.jpg?v=1794118159"},{"product_id":"qbp191822","title":"Vimar 3-Module Flush Mounting Box, Masonry Walls, Glow Wire 960C","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Vimar VM71303.AU is a 3-module flush mounting box for masonry walls, molded in black technopolymer plastic and sized around 96 x 59 x 49.8 mm.\u003c\/p\u003e\u003cp\u003eIt gives you a recessed cavity for Vimar modular wiring devices while leaving room for cable bends and terminations, which matters when you are running heavier marine-grade conductors. The body is Glow Wire tested to 960 °C for added resistance to abnormal heat.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e3-module format for Vimar modular devices when paired with the matching support frame and cover plate\u003c\/li\u003e\n\u003cli\u003eRectangular masonry box footprint around 96 x 59 mm with about 49.8 mm depth to sit flush behind finished surfaces\u003c\/li\u003e\n\u003cli\u003eGlow Wire rating 960 °C for improved resistance to abnormal heat and ignition\u003c\/li\u003e\n\u003cli\u003eExpanded internal volume (about 20% more space) to help with wiring, splices, and cable bend radius\u003c\/li\u003e\n\u003cli\u003eKnockouts on multiple sides for conduit entry; knockouts can be opened without tools\u003c\/li\u003e\n\u003cli\u003eZinc-plated fixing lugs for the support screws to reduce thread clogging during installation and plastering\u003c\/li\u003e\n\u003cli\u003eProvision for a dividing screen accessory to separate compartments when you need physical cable segregation\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eThis box is intended for solid walls. In a boat context, it fits best where you have a masonry-style substrate or a solid bulkhead build-up that can be chased or cut to accept a rectangular box. Set it level and flush to the finished surface so the faceplate sits flat once the modules are installed.\u003c\/p\u003e\u003cp\u003ePlan your conduit runs before you set the box, and keep the screw points clear during plastering or fairing work. Installation temperature range is -15 °C to +60 °C.\u003c\/p\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eConfirm that your device family uses a 3-module mounting box in the Vimar system, then match the correct support frame and cover plate to your chosen devices. If you are mounting into thin panels or hollow joinery, a hollow-wall style mounting box is the better match than a masonry box.\u003c\/p\u003e\u003cp\u003eThis is an in-wall mounting box and does not provide a sealed enclosure, so it belongs in protected interior locations rather than areas exposed to washdowns or direct spray.\u003c\/p\u003e\u003ch6\u003eUse on board\u003c\/h6\u003e\u003cp\u003eIt suits refits and new builds where you want a tidy, recessed installation for switch groups, outlets, or data sockets in cabins, saloons, and nav stations. When routing cables on a moving vessel, leave service loops and strain relief in the wall space so the device terminations are not carrying vibration loads.\u003c\/p\u003e\n\u003cspan itemprop=\"mpn\" hidden\u003eVM71303.AU\u003c\/span\u003e","brand":"Vimar","offers":[{"title":"Default Title","offer_id":53721604817077,"sku":"QBP191822","price":2.45,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/0370663_qbp191822_jpeg.jpg?v=1794119317"},{"product_id":"qbp532704","title":"Vimar Idea Dimmer Switch, 230V, 60-900W, Illuminable, White","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe Vimar VM16556.B is a 230 V AC rotary dimmer module for controlling the brightness of incandescent and halogen lighting on board. It is rated for 230 V~ 50-60 Hz and supports 60-900 W lamp loads, plus 60-300 VA when dimming through a ferromagnetic (magnetic) transformer.\u003c\/p\u003e\u003cp\u003eIt is part of the Vimar IDEA modular switching format and uses a white front that suits most cabin, saloon, and guest-area interiors. The control is a rotary potentiometer, and the control point is visible in darkness so it is easier to find during night watches.\u003c\/p\u003e\u003cp\u003eBecause this is a 230 V device, it belongs on the vessel's AC distribution (shore power or inverter output), not on a 12 V or 24 V DC lighting circuit.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e230 V~ 50-60 Hz rotary dimmer module for AC lighting circuits\u003c\/li\u003e\n\u003cli\u003eRated for 60-900 W incandescent and halogen lamp loads\u003c\/li\u003e\n\u003cli\u003eSupports 60-300 VA ferromagnetic (magnetic) transformers for low-voltage halogen circuits\u003c\/li\u003e\n\u003cli\u003eControl and regulation via rotary potentiometer\u003c\/li\u003e\n\u003cli\u003eVisible-in-darkness locator feature for low-light cabins\u003c\/li\u003e\n\u003cli\u003eWhite finish in the Vimar modular style for consistent panel layouts\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and load guidance\u003c\/h6\u003e\u003cp\u003eThis dimmer is intended for traditional incandescent or halogen lamps, and for low-voltage halogen circuits when the lamps are fed by a magnetic transformer. It is not the right choice for circuits using electronic transformers, CFL, or LED lamps unless the lamp and driver are specifically rated to work with this dimmer type.\u003c\/p\u003e\u003cp\u003eThe minimum connected load starts at 60 W. On very small lighting loads, expect limited adjustment range or unstable dimming behavior.\u003c\/p\u003e\u003ch6\u003eInstallation and onboard notes\u003c\/h6\u003e\u003cp\u003eInstall it as part of a 230 V AC circuit with power isolated at the breaker and shore power disconnected. On boats it is typically mounted in a dry interior bulkhead or panel, behind a compatible Vimar modular frame and cover plate, then finished with the matching knob and trim.\u003c\/p\u003e\u003cp\u003eThis is a good match for yachts that already use Vimar IDEA hardware and need straightforward dimming for 230 V cabin lighting or transformer-fed halogen runs.\u003c\/p\u003e\n\u003cspan itemprop=\"mpn\" hidden\u003eVM16556.B\u003c\/span\u003e","brand":"Vimar","offers":[{"title":"Default Title","offer_id":53721611305141,"sku":"QBP532704","price":68.18,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/0368801_qbp532704_jpeg.jpg?v=1794120074"}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/collections\/c969a23c-89c1-5a3a-8f37-03c939cffc68.webp?v=1794118121","url":"https:\/\/www.qualityboatparts.com\/collections\/brand-vimar.oembed","provider":"Quality Boat Parts","version":"1.0","type":"link"}