{"title":"MotorGuide","description":"","products":[{"product_id":"qbp426054","title":"MotorGuide Trolling Motor Power Plug, 2-Prong, 50A, 12-36V","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe MotorGuide 8M4000953 is a 2-prong trolling motor power plug rated for 50 amps for 12V, 24V, or 36V power systems.\u003c\/p\u003e\u003cp\u003eIt creates a clean disconnect point between your trolling motor and the boat’s power circuit, which is handy when you remove the motor for trailering, store the boat, or need to service wiring at the bow. If your current plug feels loose, shows heat marks, or cuts out when the boat bumps, replacing the connector is a smart place to start.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e2-prong trolling motor power plug format\u003c\/li\u003e\n\u003cli\u003e50 A rating for high-current trolling motor circuits\u003c\/li\u003e\n\u003cli\u003eWorks with 12V, 24V, and 36V trolling motor power setups\u003c\/li\u003e\n\u003cli\u003eBuilt to seat firmly in a matching receptacle for a steady connection\u003c\/li\u003e\n\u003cli\u003eMakes it easier to disconnect power at the bow for storage, trailering, or maintenance\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis plug is intended to mate with a matching 2-prong, 50 A trolling motor receptacle. Before ordering, compare the prong layout and housing style to what’s installed on your boat, since 2-prong plugs are not all interchangeable across brands and patterns.\u003c\/p\u003e\u003cp\u003eVoltage is not usually the limiting factor here since the plug supports 12V through 36V. The important checks are connector style and that your circuit protection and wiring are appropriate for a 50 A connector and your trolling motor’s current draw.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eDisconnect the batteries before any wiring work. Make electrical connections with marine-appropriate crimping and sealing so water and corrosion do not creep into the joint over time. Add strain relief and route the cable so the plug is not taking the load when the motor turns, stows, or gets bumped.\u003c\/p\u003e\u003cp\u003eOn open decks, place the connection point where it will not sit in standing water and where it is less likely to take direct washdowns. Keeping the contacts clean and the fit tight helps prevent heat build-up on high-current trolling motor runs.\u003c\/p\u003e\u003ch6\u003eUse on board\u003c\/h6\u003e\u003cp\u003eThis style of plug is commonly used on bow-mount trolling motor installs where you want a quick disconnect close to the motor bracket. It also fits small-boat and removable-motor setups where you regularly pull the motor between trips, as long as the mating receptacle matches the same 2-prong 50 A pattern.\u003c\/p\u003e\u003ch6\u003eCompliance and warnings\u003c\/h6\u003e\u003cp\u003eCalifornia Proposition 65 warning: This product can expose you to chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm. For more information, visit P65Warnings.ca.gov.\u003c\/p\u003e\n\u003cspan itemprop=\"mpn\" hidden\u003e8M4000953\u003c\/span\u003e","brand":"MotorGuide","offers":[{"title":"Default Title","offer_id":53721527091381,"sku":"QBP426054","price":31.0,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1280716_qbp426054.jpg?v=1794116309"},{"product_id":"qbp629688","title":"MotorGuide Trolling Motor Tie-Down Strap, For Gator Mounts, 2 x 28 in","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe MotorGuide MGA507A1 is a hook-and-loop tie down strap that secures a stowed trolling motor to its mount to help stop bounce during trailering and on rough-water runs. It measures 2 in wide by 28 in long, giving you enough wrap to cinch the shaft down without having to fight with knots or ratchets.\u003c\/p\u003e\u003cp\u003eOn a boat, this strap is used as a secondary hold-down after you stow the motor. It lays over the shaft and fastens back onto itself, keeping the motor from lifting or chattering against the bracket when the hull is taking waves, wakes, or potholes on the road.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e2 in x 28 in strap size for a secure wrap over the trolling motor shaft\u003c\/li\u003e\n\u003cli\u003eHook-and-loop closure for quick tightening, removal, and re-tensioning at the ramp\u003c\/li\u003e\n\u003cli\u003eMade to work with MotorGuide Gator mount setups, including common X3 and X5 applications\u003c\/li\u003e\n\u003cli\u003eHelps reduce stow bounce that can scuff decks, stress brackets, and wear mount hardware\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eWith the trolling motor fully stowed, run the strap over the shaft and anchor it down to the mount base, then pull it snug and press the hook-and-loop surfaces together. Set it tight enough that the shaft cannot hop in chop, but not so tight that it twists the shaft sideways or interferes with the latch mechanism. After the first run, recheck tension and adjust as the strap beds in.\u003c\/p\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis strap is intended for MotorGuide trolling motors that use a Gator-style mount. If your mount has a clear strap path over the shaft and a solid point on the base to secure to, it will function as a straightforward hold-down. For the cleanest fit, confirm you have room to route the strap without pinching cables, steering linkages, or lift-assist components.\u003c\/p\u003e\u003ch6\u003eUse on board\u003c\/h6\u003e\u003cp\u003eIt is a practical add-on for anglers who trailer frequently, run big water, or make long moves between spots where the bow takes repeated impacts. It also helps when the boat is stored on a lift or at the dock and you want the stowed motor held down against wind-driven movement.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eRinse the strap after saltwater use, especially around the hook-and-loop area where grit can reduce grip. Inspect the strap and closure periodically for fraying or debris buildup, and replace it if the fastening surfaces no longer hold firmly.\u003c\/p\u003e\n\u003cspan itemprop=\"mpn\" hidden\u003eMGA507A1\u003c\/span\u003e","brand":"MotorGuide","offers":[{"title":"Default Title","offer_id":53721528336565,"sku":"QBP629688","price":20.96,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1280727_qbp629688.jpg?v=1794116441"},{"product_id":"qbp417475","title":"MotorGuide Trolling Motor Power Receptacle, 50A, 2-Prong, 12\/24\/36V","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe MotorGuide 8M4000954 is a 50A trolling motor power receptacle that gives you a solid two-prong connection for 12V, 24V, or 36V systems.\u003c\/p\u003e\u003cp\u003eIt’s the boat-side connection point that pairs with the matching MotorGuide 50A trolling motor plug to make a clean quick-disconnect at the bow. That’s handy when you trailer often, pull the motor for storage, or want a simple way to isolate trolling motor power without leaving loose leads exposed.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e50A continuous rating for trolling motor power connections\u003c\/li\u003e\n\u003cli\u003eTwo-prong receptacle for 12V, 24V, or 36V setups\u003c\/li\u003e\n\u003cli\u003eMatches the MotorGuide 50A Trolling Motor Plug (8M4000953)\u003c\/li\u003e\n\u003cli\u003eCreates a quick-disconnect point near the trolling motor mount for faster rigging and removal\u003c\/li\u003e\n\u003cli\u003eFixed receptacle location helps keep the bow wiring tidy and easier to secure\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis receptacle is meant for trolling motor installations using a two-prong, 50A-style plug connection. Confirm your trolling motor lead uses the matching two-prong plug style and that the rest of your wiring and overcurrent protection are appropriate for a 50A connection point.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eMount the receptacle where the trolling motor lead can reach without being stretched during stow and deploy, commonly near the bow panel or close to a quick-release bracket location. Route the boat-side feed so it’s supported along the run, protected from chafe, and kept out of standing water.\u003c\/p\u003e\u003cp\u003eAfter wiring, keep the connection clean and dry in use, and periodically check for heat discoloration, looseness, or corrosion. A small amount of dielectric grease on the contact surfaces can help slow oxidation in humid or salt-affected environments.\u003c\/p\u003e\u003ch6\u003eSafety notice\u003c\/h6\u003e\u003cp\u003eWARNING: Cancer and reproductive harm - www.P65Warnings.ca.gov.\u003c\/p\u003e\n\u003cspan itemprop=\"mpn\" hidden\u003e8M4000954\u003c\/span\u003e","brand":"MotorGuide","offers":[{"title":"Default Title","offer_id":53721528402101,"sku":"QBP417475","price":31.0,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1280685_qbp417475.jpg?v=1794116446"},{"product_id":"qbp629675","title":"MotorGuide Telescoping Tiller Extension Handle, 24 in, Aluminum Tubing, Soft-Grip","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe MotorGuide MGA503A1 is a 24 inch telescoping extension handle that gives you extra reach when steering a transom-mounted tiller. It is a simple way to move your steering position forward in the boat while keeping your hand on the tiller where you need it during long trolling passes.\u003c\/p\u003e\u003cp\u003eThis extension locks in place once set, so the length stays put while you are underway. It uses aluminum tubing with a soft-grip handle, and the connector adjusts for a solid connection on many hand-steered trolling motor tillers and popular tiller kicker engines.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e24 inch telescoping tiller extension for hand-steered transom setups\u003c\/li\u003e\n\u003cli\u003eLocking length adjustment to keep the handle from creeping while you steer\u003c\/li\u003e\n\u003cli\u003eAluminum tubing construction with a soft-grip handle for better control with wet hands\u003c\/li\u003e\n\u003cli\u003eAdjustable connector that clamps down for a firm, no-wobble feel when installed correctly\u003c\/li\u003e\n\u003cli\u003eMade for trolling motors and commonly used on tiller-style kicker applications where extra reach helps\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis handle is meant for transom-mount, hand-steered tiller motors and similar tiller-style controls. Before ordering, check that your tiller has enough straight grip area for the connector to clamp securely, and confirm you have clearance for the extension to sweep through your steering arc without hitting a seat, gunwale, or console.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eFit the connector onto the tiller handle, adjust it for a snug clamp, and confirm the extension does not interfere with normal steering movement. Set the telescoping length where it feels natural from your usual driving position, then verify it locks firmly before running in chop or making tight turns.\u003c\/p\u003e\u003ch6\u003eUse on board\u003c\/h6\u003e\u003cp\u003eOn smaller fishing boats, skiffs, and utility hulls, an extension handle helps when you are trolling from a mid-boat seat or standing a bit forward for visibility and balance. It is a good match for anglers who run a hand-steered transom motor for slow trolling and want a more comfortable reach without changing the rest of the setup.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eAfter use, especially in saltwater, rinse the handle and connector with fresh water and let it dry before storage. Keep the telescoping section clean so it slides smoothly, and re-check clamp tightness periodically since vibration can loosen hardware over time.\u003c\/p\u003e\u003ch6\u003eSafety notice\u003c\/h6\u003e\u003cp\u003eWARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.\u003c\/p\u003e\n\u003cspan itemprop=\"mpn\" hidden\u003eMGA503A1\u003c\/span\u003e","brand":"MotorGuide","offers":[{"title":"Default Title","offer_id":53721530761397,"sku":"QBP629675","price":29.91,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1280726_qbp629675.jpg?v=1794116736"},{"product_id":"qbp196979","title":"MotorGuide Tour Pro Bow Mount Trolling Motor, Pinpoint GPS, 82 lb Thrust, 24V, 45in Shaft, Cable Steer, Foot Control, Freshwater","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe MotorGuide 941900020 is a 24 V bow-mount trolling motor with 82 lb peak thrust, a 45 in shaft, cable-steer foot control, and Pinpoint GPS for holding position and managing heading while you fish.\u003c\/p\u003e\u003cp\u003eIt is a freshwater setup that keeps the instant feel of cable steering while adding GPS modes like Anchor, Jog, Heading Lock, and Cruise Control. Steering range goes past 180 degrees, so backing down is handled by rotating the lower unit rather than switching the motor into reverse.\u003c\/p\u003e\u003cp\u003eThis is a good match for anglers who live on the front deck and want fast steering response, then want to lock the boat on a spot without dropping an anchor.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e82 lb peak thrust on a 24 V system with a 45 in (114.3 cm) shaft length\u003c\/li\u003e\n\u003cli\u003eCable-steer foot pedal control with a metal upper pad and grip tape\u003c\/li\u003e\n\u003cli\u003ePinpoint GPS modes: Anchor, Jog, Heading Lock, and Cruise Control\u003c\/li\u003e\n\u003cli\u003eDigital variable speed control with 20 speed levels\u003c\/li\u003e\n\u003cli\u003eWireless GPS control included, plus an LED dashboard for power, battery, and GPS status\u003c\/li\u003e\n\u003cli\u003e360 degree breakaway mount with integrated Bounce Buster support\u003c\/li\u003e\n\u003cli\u003eIntegrated cable routing to keep rigging tighter at the bow\u003c\/li\u003e\n\u003cli\u003eZero-G lift assist with Bulldog latches and a gas spring to ease stow and deploy\u003c\/li\u003e\n\u003cli\u003eTwo blade Katana propeller\u003c\/li\u003e\n\u003cli\u003eTwo-piece shaft with a stainless steel outer column and a composite inner shaft\u003c\/li\u003e\n\u003cli\u003eCompatible with lithium-ion trolling batteries when supplying stable 24 V power\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eWhat’s included\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eSteering assembly\u003c\/li\u003e\n\u003cli\u003eMount\u003c\/li\u003e\n\u003cli\u003eBounce buster assembly\u003c\/li\u003e\n\u003cli\u003eGas spring\u003c\/li\u003e\n\u003cli\u003ePinpoint GPS remote\u003c\/li\u003e\n\u003cli\u003eNMEA 2000 T-connector\u003c\/li\u003e\n\u003cli\u003eTie-down strap\u003c\/li\u003e\n\u003cli\u003eKatana propeller with prop pin, washer, and nut\u003c\/li\u003e\n\u003cli\u003eMounting hardware (mounting screws, washers, rubber spacers, nylon lock nuts)\u003c\/li\u003e\n\u003cli\u003eCable routing ties and clips with mounting screws\u003c\/li\u003e\n\u003cli\u003eTorx bits (T20 and T40), plus Allen screws and plastic retaining washers\u003c\/li\u003e\n\u003cli\u003eSelf-tapping screw\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis model is rated for freshwater use and mounts on the bow. The 45 in shaft length is the key fit point, so make sure it keeps the prop submerged in your usual chop while still clearing the bow when stowed.\u003c\/p\u003e\u003cp\u003eCable steering works best when the foot pedal is placed where you can stand and work it naturally, with enough open space for the pedal to travel and return to neutral without snagging gear.\u003c\/p\u003e\u003ch6\u003eElectrical and system integration\u003c\/h6\u003e\u003cp\u003ePlan on a dedicated 24 V trolling-motor battery bank using 12 V deep-cycle marine batteries wired for 24 V. A manual-reset circuit breaker should be installed on the positive lead within 6 ft (1.8 m) of the batteries.\u003c\/p\u003e\u003cp\u003eThe included battery leads are 10-gauge. If your batteries are farther away, use heavier cable rather than extending the stock leads beyond the recommended total run.\u003c\/p\u003e\u003cp\u003ePinpoint GPS can tie into an NMEA 2000 backbone for chartplotter control and motor status. For cleaner sonar performance, power sensitive electronics from your starting or accessory battery instead of the trolling-motor bank.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eDry-fit the mount location before drilling so the shaft can deploy without hitting the rub rail, bow light, or trailer hardware. After mounting, route power and control cabling so the deck stays clear and the motor can steer freely through its full range.\u003c\/p\u003e\u003cp\u003eGPS-guided modes rely on unobstructed steering. Before using Anchor or Heading Lock, confirm the pedal area is clear and the motor can rotate without binding.\u003c\/p\u003e\n\u003cspan itemprop=\"mpn\" hidden\u003e941900020\u003c\/span\u003e","brand":"MotorGuide","offers":[{"title":"Default Title","offer_id":53721536233653,"sku":"QBP196979","price":4907.07,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1280676_qbp196979.webp?v=1794117001"},{"product_id":"qbp425590","title":"MotorGuide Xi Series Trolling Motor Foot Pedal, Wireless 2.4GHz","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe MotorGuide 8M0092069 is a 2.4 GHz wireless foot pedal for Xi series electric steer trolling motors, including Xi3 and Xi5 models. The heel-toe steering layout lets you turn right with toe-down and left with heel-down, then stop the turn by letting the pedal return to the center detent. Steering range allows you to rotate the motor past 360 degrees in either direction, which is handy when you are lining up on structure or following a contour.\u003c\/p\u003e\u003cp\u003eSpeed is set with the dial on the pedal, with both momentary run and constant on\/off control at the selected speed. The pedal runs on two AA alkaline batteries and syncs to the motor receiver, so it can be placed where your feet naturally land on a casting deck or bow platform without a cable run across the boat.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e2.4 GHz wireless foot control for compatible MotorGuide Xi series motors (Xi3 and Xi5)\u003c\/li\u003e\n\u003cli\u003eHeel-toe steering with a center detent to stop turning without hunting for a switch\u003c\/li\u003e\n\u003cli\u003eSteering range that can rotate the motor past 360 degrees in either direction\u003c\/li\u003e\n\u003cli\u003eSpeed control dial plus both momentary run and constant propeller on\/off at the selected speed\u003c\/li\u003e\n\u003cli\u003eAnchor button control on motors with GPS installed, and it also functions as the pedal on\/off control\u003c\/li\u003e\n\u003cli\u003eReceiver can sync up to 40 wireless controllers for multi-control setups\u003c\/li\u003e\n\u003cli\u003eUses two AA alkaline batteries with a gasketed cover to help keep the battery compartment sealed\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis pedal is intended for MotorGuide Xi series motors that support wireless controllers. It is commonly used with Xi3 and Xi5 models and communicates through the motor’s receiver once it is synced, so there is no hardwired foot pedal connection to route through the deck. If your boat runs multiple wireless controls, the receiver can store many devices, which is useful when you want both a foot pedal and other controls on board.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eSyncing is done at power-up. After connecting the trolling motor to its power source, press and hold the propeller and anchor buttons on the pedal within ten seconds, then listen for the multi-tone beep that confirms the receiver learned the pedal. When activating more than one pedal, unplug the motor from power and plug it back in between each device activation.\u003c\/p\u003e\u003cp\u003eBattery access is under the cover secured by two screws. Replace with two AA alkaline batteries in the correct polarity and make sure the rubber seal is seated before reinstalling the cover.\u003c\/p\u003e\u003ch6\u003eUse cases on board\u003c\/h6\u003e\u003cp\u003eThis setup makes sense for anglers who want their trolling motor to respond while they are moving around the bow, working a rod locker, or landing a fish, since the pedal is not tied to a fixed cable location. It is also a good match for boats where keeping the deck clear matters, such as bass boats, multispecies rigs, and open-bow skiffs with a busy casting area.\u003c\/p\u003e\u003ch6\u003eSafety and compliance\u003c\/h6\u003e\u003cp\u003eRotating propellers can cause serious injury or death. Never start or operate the trolling motor out of water.\u003c\/p\u003e\u003cp\u003eWhen activating the trolling motor with the foot pedal, the motor can start at the last selected speed and course settings. Before pressing the pedal, hold on to a seat or handhold and advise passengers to do the same.\u003c\/p\u003e\u003cp\u003eWARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.\u003c\/p\u003e\n\u003cspan itemprop=\"mpn\" hidden\u003e8M0092069\u003c\/span\u003e","brand":"MotorGuide","offers":[{"title":"Default Title","offer_id":53721537773749,"sku":"QBP425590","price":369.69,"currency_code":"USD","in_stock":false}]},{"product_id":"qbp629579","title":"MotorGuide Mounting Isolator Kit, 4-Pack, Stainless Steel Bolts","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe MotorGuide MGA015PB6 is a mounting isolator kit that helps absorb shock and cut down vibration when you bolt marine accessories in place. It is commonly used for trolling motor mounts and other deck mounted hardware where vibration can work fasteners loose over time and where you want a cleaner install without needing full access under the deck or behind the console.\u003c\/p\u003e\u003cp\u003eThe kit uses rubber isolators with a molded-in nut and stainless steel bolts. As the bolts are tightened, the isolators expand into a mushroom shape under the mounting surface, helping the mount clamp down securely while the rubber takes the edge off impacts and vibration.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eRubber isolators help reduce vibration transfer into mounted electronics and accessories.\u003c\/li\u003e\n\u003cli\u003eMolded-in nut in each isolator simplifies tightening from the topside.\u003c\/li\u003e\n\u003cli\u003eIsolator expands into a mushroom shape as it is tightened to help hold the mount in place.\u003c\/li\u003e\n\u003cli\u003eUseful for installs with limited underside access under decks or behind consoles.\u003c\/li\u003e\n\u003cli\u003eStainless steel mounting bolts included for a clean bolt-through installation.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eWhat’s included\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e4 rubber isolators\u003c\/li\u003e\n\u003cli\u003e4 stainless steel bolts\u003c\/li\u003e\n\u003cli\u003eMounting instructions\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eLay out the mount, bracket, or accessory base and confirm your hole pattern and clearance before drilling. Insert the rubber isolators through the mounting holes, start the stainless bolts, then tighten until the rubber mushrooms under the surface and the assembly feels firm. The goal is a stable clamp with the rubber still doing its job, not crushing the isolator.\u003c\/p\u003e\u003cp\u003eAfter the first run, recheck fastener tightness. Vibration and deck materials can settle slightly, especially on the first outing after installation.\u003c\/p\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis kit is intended for bolt-through mounting applications where you want some isolation between the mount and the boat structure. It is a good match for trolling motor mounts and many other marine accessories that use standard bolts and washers for deck mounting. Confirm your deck thickness, hole size, and the space available below the mounting surface so the isolators can expand properly.\u003c\/p\u003e\u003ch6\u003eUse cases on board\u003c\/h6\u003e\u003cp\u003eIt is a practical choice for bass boats, bay boats, and center consoles where you are installing gear on the bow deck or near the console and access is tight. It can also be helpful on boats that see chop regularly and where sensitive electronics benefit from reduced shock transfer.\u003c\/p\u003e\u003ch6\u003eMaterials and corrosion resistance\u003c\/h6\u003e\u003cp\u003eThe isolators are rubber and the fasteners are stainless steel. The rubber helps isolate vibration at the mounting points while the stainless hardware suits typical wet, salt, and washdown conditions when installed with normal marine best practices.\u003c\/p\u003e\u003ch6\u003eSafety information\u003c\/h6\u003e\u003cp\u003eWARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.\u003c\/p\u003e\n\u003cspan itemprop=\"mpn\" hidden\u003eMGA015PB6\u003c\/span\u003e","brand":"MotorGuide","offers":[{"title":"Default Title","offer_id":53721538789557,"sku":"QBP629579","price":21.36,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1280717_qbp629579.jpg?v=1794117280"},{"product_id":"qbp417557","title":"MotorGuide Garmin 8-Pin HD+ Sonar Adapter Cable, Tour\/Tour Pro HD+","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe MotorGuide 8M4004178 is an HD+ sonar adapter cable that connects a Tour or Tour Pro HD+ trolling motor to a Garmin fishfinder that uses an 8-pin transducer port. It carries traditional 83\/200 kHz 2D sonar and 455\/800 kHz high-definition down-looking sonar signals so you can read bottom and structure directly under the trolling motor.\u003c\/p\u003e\u003cp\u003eThis is the clean way to use the trolling motor’s built-in sonar without adding an external transducer to the bracket. It is meant for HD+ enabled motors and it is not compatible with Xi Series motors.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eConnects MotorGuide Tour and Tour Pro HD+ sonar output to a Garmin 8-pin transducer port\u003c\/li\u003e\n\u003cli\u003ePasses 83\/200 kHz 2D sonar and 455\/800 kHz high-definition down-looking sonar signals from the trolling motor\u003c\/li\u003e\n\u003cli\u003eCompatible with Garmin GPSMAP and echoMAP series that use the Garmin 8-pin transducer connector\u003c\/li\u003e\n\u003cli\u003eGarmin SV models that use a 12-pin sounder connection require Garmin 8-pin transducer to 12-pin Sounder Adapter Cable with XID (010-12122-10), sold separately\u003c\/li\u003e\n\u003cli\u003eNot compatible with Xi Series motors\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eUse this cable only when you have a MotorGuide Tour or Tour Pro that is HD+ enabled and you want to plug that sonar into a Garmin unit with an 8-pin transducer input. If your Garmin unit does not have an 8-pin transducer port, confirm what adapter your display needs before ordering.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eConnect the motor end to the HD+ sonar lead from the trolling motor, then connect the Garmin end to the display’s 8-pin transducer port. Route the cable with a gentle drip loop and secure it so it cannot rub on the shaft, hinge points, or steering cables when stowing and deploying.\u003c\/p\u003e\u003cp\u003eFor the cleanest sonar picture, keep sonar cabling separated from high-current trolling motor power wiring where possible, and use strain relief at the head unit so vibration and trailering do not pull on the connector.\u003c\/p\u003e\u003ch6\u003eUse cases on board\u003c\/h6\u003e\u003cp\u003eThis is a good match for bow-mount setups where the angler wants sonar that tracks exactly where the trolling motor points, especially on bass boats and multi-species rigs that run Garmin electronics at the bow. It also helps on boats where you want fewer exposed transducer mounts and a simpler rigging layout.\u003c\/p\u003e\n\u003cspan itemprop=\"mpn\" hidden\u003e8M4004178\u003c\/span\u003e","brand":"MotorGuide","offers":[{"title":"Default Title","offer_id":53721540952245,"sku":"QBP417557","price":77.54,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1280691_qbp417557.jpg?v=1794117497"},{"product_id":"qbp196793","title":"MotorGuide Xi5 Wireless Bow Mount Trolling Motor, Pinpoint GPS","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe MotorGuide Xi5 is a bow-mount trolling motor family with electric steering, wireless control, and Pinpoint GPS options for holding position and working structure with less fuss at the bow. Across the range you can match thrust and power system to your boat: 55 lb models run on 12 V (up to 52 A max draw), 80 lb models run on 24 V (up to 56 A), and 105 lb models run on 36 V (up to 41 A), with shaft lengths from 48 in to 72 in.\u003c\/p\u003e\u003cp\u003eFreshwater Sonar\/GPS versions add a built-in 83\/200 kHz 2D sonar transducer in the lower unit, along with Pinpoint GPS functions such as GPS-assisted anchoring, jog, heading lock, cruise control, and route record. A handheld wireless remote is part of the control package across the range, and freshwater versions also include a wireless foot pedal with heel-toe steering.\u003c\/p\u003e\u003cp\u003eThe mount sits low on the bow and guides the motor into the stowed position, then secures it with a secondary lock. The base uses anodized aluminum with stainless hardware, the electronics are encapsulated, and a protection circuit helps reduce lower-unit damage if the prop stalls. The composite shaft flexes under impact and is backed by a lifetime warranty on the shaft.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eBow-mount electric steering with wireless control for steering and speed changes from different spots on the boat\u003c\/li\u003e\n\u003cli\u003eThrust and voltage options: 55 lb (12 V), 80 lb (24 V), 105 lb (36 V)\u003c\/li\u003e\n\u003cli\u003eShaft lengths offered across the line: 48 in, 54 in, 60 in, and 72 in\u003c\/li\u003e\n\u003cli\u003ePinpoint GPS functions on GPS-equipped models, including GPS anchoring, jog, heading lock, cruise control, and route record\u003c\/li\u003e\n\u003cli\u003eSonar\/GPS freshwater variants include a built-in 83\/200 kHz 2D sonar transducer in the lower unit\u003c\/li\u003e\n\u003cli\u003eLED status indicator dashboard for quick checks of key functions and battery level\u003c\/li\u003e\n\u003cli\u003eLow-profile mount with guided stow\/deploy and a secondary lock to help prevent accidental deployment\u003c\/li\u003e\n\u003cli\u003eEncapsulated electronics with a protection circuit that helps when the prop is stalled\u003c\/li\u003e\n\u003cli\u003eComposite shaft that flexes under impact\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eVariants\u003c\/h6\u003e\u003cp\u003eThis Xi5 range is offered in multiple configurations that change the shaft length (48, 54, 60, or 72 in) and thrust rating (55, 80, or 105 lb). Those choices also set the required battery system voltage (12 V, 24 V, or 36 V), which matters for battery count, wiring, and breaker selection.\u003c\/p\u003e\u003cp\u003eIn this set, freshwater variants are listed as Sonar\/GPS and include the built-in 83\/200 kHz transducer along with Pinpoint GPS control. The saltwater variants here are GPS-only, keeping the Pinpoint GPS control package without built-in sonar.\u003c\/p\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003ePick shaft length based on your bow height and the water you normally fish. The practical goal is keeping the lower unit submerged when the bow lifts in chop, without ending up with a shaft that is awkward to stow or interferes with your bow layout.\u003c\/p\u003e\u003cp\u003eThrust selection is tied to boat weight, wind, and current. Once you choose 55, 80, or 105 lb, plan your battery bank around the matching 12 V, 24 V, or 36 V requirement so you are not reworking the electrical system later.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eBow-mount installation typically needs a flat mounting surface with access below for backing hardware and cable routing. Leave clearance for the motor head to rotate and for the shaft path in the stowed position, especially if you have a bow rail, cleats, or an anchor locker hatch nearby.\u003c\/p\u003e\u003cp\u003eAfter mounting, cycle the stow and deploy motion on the trailer and confirm the secondary lock engages cleanly. A quick check now helps avoid surprises at the ramp.\u003c\/p\u003e\u003ch6\u003eElectrical and system integration\u003c\/h6\u003e\u003cp\u003eXi5 uses digital variable speed control for smooth low-speed adjustments while trolling. GPS-equipped variants add Pinpoint GPS operation through the handheld remote, which is useful when you are moving around the cockpit or fighting a fish away from the bow.\u003c\/p\u003e\u003cp\u003eIf you want motor control from a compatible display, the Xi-series gateway can tie the system into an existing NMEA 2000 network for touchscreen integration with compatible Lowrance and Simrad units, as well as Mercury VesselView displays.\u003c\/p\u003e\u003ch6\u003eUse on board\u003c\/h6\u003e\u003cp\u003eFor bass boats, multi-species rigs, and freshwater skiffs, the Sonar\/GPS variants make sense when you want GPS anchoring plus a built-in 2D sonar source on the trolling motor. For bay boats and inshore saltwater skiffs, the GPS-only variants fit crews that rely on position hold and jog while dealing with spray and frequent rinsing.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eRinse the mount, shaft, and lower unit after each trip, especially on saltwater installations, and keep the stow\/deploy pivots free of grit. Periodically check mounting hardware for tightness and inspect the prop area for fishing line buildup.\u003c\/p\u003e\u003ch6\u003eCompliance and notices\u003c\/h6\u003e\u003cp\u003eWARNING: This product can expose you to chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. For more information, visit P65Warnings.ca.gov.\u003c\/p\u003e\n\u003cspan itemprop=\"mpn\" hidden\u003e940800211\u003c\/span\u003e\n\u003cspan itemprop=\"mpn\" hidden\u003e941700100\u003c\/span\u003e\n\u003cspan itemprop=\"mpn\" hidden\u003e941700090\u003c\/span\u003e\n\u003cspan itemprop=\"mpn\" hidden\u003e941700110\u003c\/span\u003e\n\u003cspan itemprop=\"mpn\" hidden\u003e940800250\u003c\/span\u003e\n\u003cspan itemprop=\"mpn\" hidden\u003e940800220\u003c\/span\u003e\n\u003cspan itemprop=\"mpn\" hidden\u003e941700170\u003c\/span\u003e\n\u003cspan itemprop=\"mpn\" hidden\u003e940800230\u003c\/span\u003e\n\u003cspan itemprop=\"mpn\" hidden\u003e940800360\u003c\/span\u003e","brand":"MotorGuide","offers":[{"title":"Freshwater \/ 48\" 55lbs \/ Sonar\/GPS","offer_id":53721549537461,"sku":"QBP196793-V6","price":3283.96,"currency_code":"USD","in_stock":false},{"title":"Saltwater \/ 60\" 105lbs \/ GPS","offer_id":53721549570229,"sku":"QBP196793-V3","price":4435.22,"currency_code":"USD","in_stock":false},{"title":"Saltwater \/ 60\" 80lbs \/ GPS","offer_id":53721549602997,"sku":"QBP196793-V2","price":3963.4,"currency_code":"USD","in_stock":false},{"title":"Saltwater \/ 48\" 80lbs \/ GPS","offer_id":53721549635765,"sku":"QBP196793-V4","price":3944.52,"currency_code":"USD","in_stock":false},{"title":"Freshwater \/ 54\" 105lb \/ Sonar\/GPS","offer_id":53721549668533,"sku":"QBP196793-V9","price":4246.5,"currency_code":"USD","in_stock":false},{"title":"Freshwater \/ 54\" 55lbs \/ Sonar\/GPS","offer_id":53721549701301,"sku":"QBP196793-V7","price":3491.55,"currency_code":"USD","in_stock":false},{"title":"Saltwater \/ 72\" 105lbs \/ GPS","offer_id":53721549734069,"sku":"QBP196793-V5","price":4812.7,"currency_code":"USD","in_stock":false},{"title":"Freshwater \/ 54\" 80lbs \/ Sonar\/GPS","offer_id":53721549766837,"sku":"QBP196793-V8","price":3944.52,"currency_code":"USD","in_stock":false},{"title":"Freshwater \/ 72\" 105lbs \/ Sonar\/GPS","offer_id":53721549799605,"sku":"QBP196793-V1","price":4529.61,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1282548_qbp196793.jpg?v=1794117888"},{"product_id":"qbp417507","title":"MotorGuide Katana 2-Blade Weedless Trolling Motor Propeller, For MotorGuide 3.5 in Hub Trolling Motors, 10.25 in Diameter, Engineered Polymer, Includes Prop Pin Nut Washer","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe MotorGuide 8M4004173 is a Katana 2-blade weedless propeller made for MotorGuide trolling motors that use a 3.5 inch hub. It has a 10.25 inch diameter and is built from engineered polymer for everyday use around cover.\u003c\/p\u003e\u003cp\u003eThis prop is built to keep moving when you are working through weeds, shallow flats, or current where a standard prop can load up with grass. It is also used as the stock prop on Tour and Tour Pro motors, and it is a common swap when you want the Katana style on another 3.5 inch hub MotorGuide lower unit.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eFits MotorGuide trolling motors that take a 3.5 inch hub prop (commonly found on Tour, Tour Pro, and Xi series models).\u003c\/li\u003e\n\u003cli\u003e2-blade weedless shape helps shed vegetation and reduces hang-ups around grass and shallow cover.\u003c\/li\u003e\n\u003cli\u003e10.25 inch diameter for strong thrust at typical trolling motor speeds.\u003c\/li\u003e\n\u003cli\u003eEngineered polymer construction that handles everyday bumps and vibration without the corrosion concerns of metal props.\u003c\/li\u003e\n\u003cli\u003eUp to 30% more battery efficiency compared with previous MotorGuide props.\u003c\/li\u003e\n\u003cli\u003eMade in the USA.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eWhat’s included\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003ePropeller\u003c\/li\u003e\n\u003cli\u003eProp pin\u003c\/li\u003e\n\u003cli\u003eNut\u003c\/li\u003e\n\u003cli\u003eWasher\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eFit is determined by the hub size on your trolling motor, not boat length or horsepower. This Katana prop uses the 3.5 inch hub system, so it is a match when your current MotorGuide prop and hardware are the 3.5 inch style. If you are replacing an older prop, confirm the hub size and shaft hardware style before ordering.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eDisconnect power to the trolling motor before working at the prop. Remove the existing nut and hardware, clear any fishing line from the shaft, then install the pin, slide the prop on, and reassemble with the washer and nut from the kit. After installation, spin the prop by hand to confirm it turns freely and does not contact the lower unit.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eCheck the prop area occasionally for wrapped line, especially after fishing grass or brush. Rinse the prop and lower unit after use in dirty or brackish water, and recheck the prop nut tightness as part of routine trolling motor inspections.\u003c\/p\u003e\n\u003cspan itemprop=\"mpn\" hidden\u003e8M4004173\u003c\/span\u003e","brand":"MotorGuide","offers":[{"title":"Default Title","offer_id":53721551438005,"sku":"QBP417507","price":64.11,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1280686_qbp417507.jpg?v=1794117947"},{"product_id":"qbp425406","title":"MotorGuide Medium-Duty Trolling Motor Receptacle, 12\/24\/36V, 2\/3-Wire, 1-1\/8in Mounting Hole, 8\/10 AWG, Watertight Sealing Cap","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe MotorGuide 8M0092066 is a medium-duty trolling motor receptacle that mounts through a panel and gives you a quick disconnect point for trolling motor power.\u003c\/p\u003e\u003cp\u003eIt works with 12, 24, and 36 volt trolling motor systems and supports 2-wire or 3-wire configurations. The body installs through a standard 1-1\/8\" diameter mounting hole and accepts 8 AWG or 10 AWG wire.\u003c\/p\u003e\u003cp\u003eA sealing cap closes the opening when the plug is removed, and drain holes in the receptacle help keep water from sitting around the electrical contacts.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eCompatible with 12, 24, and 36 volt trolling motor power circuits\u003c\/li\u003e\n\u003cli\u003eWorks with 2-wire or 3-wire wiring layouts\u003c\/li\u003e\n\u003cli\u003eFits a standard 1-1\/8\" diameter mounting hole\u003c\/li\u003e\n\u003cli\u003eAccepts 8 AWG and 10 AWG wire\u003c\/li\u003e\n\u003cli\u003eCap seals the receptacle when not in use to help keep spray and rain out\u003c\/li\u003e\n\u003cli\u003eDrain holes help move water away from the electrical components\u003c\/li\u003e\n\u003cli\u003ePlated brass electrical components for consistent contact in a wet environment\u003c\/li\u003e\n\u003cli\u003eConstruction resists corrosion during marine use\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and wiring\u003c\/h6\u003e\u003cp\u003eMount the receptacle where you can reach it on the bow and where the back side stays accessible for wiring. After drilling the 1-1\/8\" hole, dry-fit the body so the cap can open fully and the cable can route without a tight bend.\u003c\/p\u003e\u003cp\u003eUse the wire gauge your trolling motor circuit calls for and keep connections tight so vibration does not work them loose over time. Circuit protection and conductor sizing should follow the trolling motor manufacturer guidance and your boat's electrical standards.\u003c\/p\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis is the receptacle side of a trolling motor quick-disconnect. Pair it with a matching trolling motor plug and confirm your system voltage and wire count before cutting the panel.\u003c\/p\u003e\u003ch6\u003eUse on board\u003c\/h6\u003e\u003cp\u003eA good match for boats that remove the trolling motor for trailering, storage, or service and want a consistent disconnect at the bow instead of hardwiring the leads.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eKeep the cap closed when the plug is removed, and rinse spray off the exterior after a day on the water. Periodically check terminal tightness and look for heat discoloration that can point to a loose connection.\u003c\/p\u003e\u003ch6\u003eRegulatory notice\u003c\/h6\u003e\u003cp\u003eWARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.\u003c\/p\u003e\n\u003cspan itemprop=\"mpn\" hidden\u003e8M0092066\u003c\/span\u003e","brand":"MotorGuide","offers":[{"title":"Default Title","offer_id":53721571852469,"sku":"QBP425406","price":45.34,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1280695_qbp425406.jpg?v=1794118544"},{"product_id":"qbp566813","title":"MotorGuide X3-55FW Bow-Mount Trolling Motor, Freshwater, 12V, 55lb Thrust, 50in Shaft, Hand Control, Digital","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe MotorGuide 940200190 is a 12V freshwater bow-mount trolling motor with 55 lb thrust and a 50 inch shaft. This is the X3-55FW HB configuration with hand control and digital variable-speed operation, so you can dial in small speed changes instead of stepping through fixed speed clicks.\u003c\/p\u003e\u003cp\u003eIt is built around a composite shaft and a bow-mount bracket that stows and deploys with a latch and lock pin. For anglers running a dedicated 12V deep-cycle setup, it is a straightforward way to add quiet boat positioning for working shorelines, docks, and weed edges without jumping up to a 24V system.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e55 lb peak thrust on a 12V system\u003c\/li\u003e\n\u003cli\u003e50 inch shaft length for bow-mounted installations\u003c\/li\u003e\n\u003cli\u003eHand control with an extending handle and adjustable steering tension collar\u003c\/li\u003e\n\u003cli\u003eDigital variable-speed control with forward and reverse selection\u003c\/li\u003e\n\u003cli\u003eBattery indicator light for quick state-of-charge checks while you fish\u003c\/li\u003e\n\u003cli\u003eComposite shaft backed by a limited lifetime warranty\u003c\/li\u003e\n\u003cli\u003eStainless steel propeller shaft with a 3-blade Machete III prop\u003c\/li\u003e\n\u003cli\u003eTypical rigging uses 6-gauge wire and a manual-reset breaker in the positive lead (50A, or 60A preferred)\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003ePlan the mount location so the motor can swing and stow without the column contacting the bow. A practical rule is to leave about 3 inches of clearance between the bow and the motor column when it is deployed.\u003c\/p\u003e\u003cp\u003eUse at least four mounting bolts and spread them as far apart as practical for a stable base. Drill clean 1\/4 inch holes, and on fiberglass decks, a light countersink helps reduce the chance of gelcoat cracking around the fasteners.\u003c\/p\u003e\u003ch6\u003eElectrical and system integration\u003c\/h6\u003e\u003cp\u003eThis model runs on a single 12V battery. For consistent thrust and longer runtimes, pair it with a dedicated deep-cycle marine battery and keep the trolling motor circuit separate from your engine starting battery whenever possible.\u003c\/p\u003e\u003cp\u003eInstall a manual-reset circuit breaker in line with the positive lead, close to the battery. Keep all cable ends clean and tight, and use appropriately sized cable for the length of the run so voltage drop does not show up as lost power on the water.\u003c\/p\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThe 50 inch shaft length is commonly used on boats with a higher bow or raised casting deck where a shorter shaft can ventilate in chop. When setting motor depth, keep the propeller fully submerged, typically 6 to 12 inches below the water surface, to avoid pulling air and losing bite.\u003c\/p\u003e\u003cp\u003eThis is a freshwater unit. If it sees brackish spray or gets trailered in road salt, rinse it down with clean water afterward and pay attention to fasteners and electrical connections.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eBefore each trip, check the mount hardware for tightness, look over the battery connections for corrosion, and confirm the prop nut is secure. After use, disconnect power at the battery and clear weeds or fishing line from the prop area so it does not work its way into the shaft.\u003c\/p\u003e\u003cp\u003eRinse the motor with fresh water to remove grit, and lubricate pivot points periodically as they start to squeak. Avoid aerosol lubricants on the bracket and steering areas, and keep grease off the column sleeves so steering effort stays consistent.\u003c\/p\u003e\n\u003cspan itemprop=\"mpn\" hidden\u003e940200190\u003c\/span\u003e","brand":"MotorGuide","offers":[{"title":"Default Title","offer_id":53721579749557,"sku":"QBP566813","price":1193.08,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1281405_qbp566813.jpg?v=1794118764"},{"product_id":"qbp425702","title":"MotorGuide Quick-Disconnect Battery Terminals, Top Post, 4-6 AWG, 500A Continuous, 800A Surge, 12V, Pair","description":"\u003cpre class=\"ql-syntax\" spellcheck=\"false\"\u003eOverview\n\u003c\/pre\u003e\u003cp\u003eThe MotorGuide 8M0092072 is a set of quick disconnect battery terminals that makes it easier to remove a battery connection for charging, storage, or service. It fits 4 to 6 gauge wire and is rated for 500 amps continuous, 800 amps surge at 12 volts.\u003c\/p\u003e\u003cp\u003eThe terminal body is made from a copper zinc alloy, and the red and black insulated covers help keep polarity clear while reducing accidental contact around the battery. Jump cables can be attached without removing the connectors, which helps when you need a boost at the dock or at the ramp.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eQuick disconnect clamp style to simplify battery removal for charging, storage, and maintenance\u003c\/li\u003e\n\u003cli\u003eFits 4 to 6 gauge wire\u003c\/li\u003e\n\u003cli\u003eRated 500 amps continuous and 800 amps surge at 12 volts\u003c\/li\u003e\n\u003cli\u003eCopper zinc alloy terminal body\u003c\/li\u003e\n\u003cli\u003eRed and black insulated covers to help keep polarity obvious and reduce accidental contact\u003c\/li\u003e\n\u003cli\u003eJump cables can be attached without removing the connectors\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis is a top-post battery terminal style, sized for the heavier battery leads commonly used on trolling motor and accessory battery circuits. Confirm you have 4 to 6 gauge cable and enough clearance above the battery posts to operate the disconnect in your battery box, aft locker, or under-seat compartment.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eDisconnect power before working on the battery, then route the cable so it will not chafe on edges or hinge points. Tighten the connection firmly and recheck it after the first few trips, especially on boats that see pounding, vibration, or frequent trailering.\u003c\/p\u003e\u003ch6\u003eUse on board\u003c\/h6\u003e\u003cp\u003eThis terminal set is a good match for anglers and cruisers who regularly pull batteries for bench charging or off-season storage, particularly when access is tight. It also helps during troubleshooting when you want a quick way to isolate a battery without disturbing the cable end each time.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eAs part of routine battery checks, keep the covers in place and inspect the contact areas for buildup. Cleaning the posts and contact faces and using a light corrosion inhibitor on exposed metal can help keep resistance low on high-current circuits.\u003c\/p\u003e\u003ch6\u003eSafety notice\u003c\/h6\u003e\u003cp\u003eWARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.\u003c\/p\u003e\n\u003cspan itemprop=\"mpn\" hidden\u003e8M0092072\u003c\/span\u003e","brand":"MotorGuide","offers":[{"title":"Default Title","offer_id":53721580404917,"sku":"QBP425702","price":33.58,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1280708_qbp425702_jpeg.jpg?v=1794118777"},{"product_id":"qbp425717","title":"MotorGuide Universal Quick Release Mounting Bracket, For Cable \u0026 Electric-Steer Motors, Slides Inboard 5-3\/4 in, Anodized Aluminum","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe MotorGuide 8M0095972 is a universal quick-release mounting bracket that lets you remove and reinstall a MotorGuide trolling motor without unbolting the mount from the deck.\u003c\/p\u003e\u003cp\u003eThe two-plate system locks with a cam handle and a sliding wedge fit, and the base can shift the motor up to 5-3\/4 in. inboard for extra clearance when launching or loading.\u003c\/p\u003e\u003cp\u003eWith anodized aluminum plates and stainless mounting hardware, it holds up better around salt spray and routine washdowns.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eQuick-release two-plate bracket with a cam-lock handle for fast removal and reattachment.\u003c\/li\u003e\n\u003cli\u003eWorks with MotorGuide cable-steer and electric-steer trolling motors.\u003c\/li\u003e\n\u003cli\u003eSlide base repositions the motor up to 5-3\/4 in. inboard for clearance at the ramp, dock, or trailer.\u003c\/li\u003e\n\u003cli\u003eAnodized aluminum construction with stainless hardware to resist corrosion.\u003c\/li\u003e\n\u003cli\u003eHandle can be secured with the included clip or a padlock (padlock sold separately).\u003c\/li\u003e\n\u003cli\u003eExtra top plates are available separately for swapping between multiple motors.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eUse the bottom plate as a template, then drill four 17\/64 in. holes and through-bolt the base to the deck with the supplied 1\/4-20 x 3 in. hardware. Rubber washers sit between the plate and the deck, with flat washers and nylock nuts underneath.\u003c\/p\u003e\u003cp\u003eAttach your trolling motor mount bracket to the top plate using the provided 1\/4-20 screws. Two screw lengths are included so you can match the thickness of your motor mount and still get full thread engagement without the fasteners poking through the plate.\u003c\/p\u003e\u003cp\u003eTo attach the motor, leave the handle open, set the top plate onto the base, slide it toward port until the wedges engage, then close the handle. For removal, open the handle, slide toward starboard, and lift the motor straight up.\u003c\/p\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis setup works best when you can reach the underside of the mounting area to install washers and nylock nuts. Before drilling, confirm the bracket has room to slide and that the motor clears the rub rail and bow hardware in the stowed position.\u003c\/p\u003e\u003cp\u003eIt suits anglers who take the trolling motor off the boat for storage or security, and anyone who wants the option to move between MotorGuide cable-steer and electric-steer setups.\u003c\/p\u003e\u003ch6\u003eWhat's included\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eBase plate\u003c\/li\u003e\n\u003cli\u003eMounting plate (top plate)\u003c\/li\u003e\n\u003cli\u003eHardware pack: 4 x 1\/4-20 x 3 in. mounting bolts, 4 x 1\/4 in. flat washers, 4 x 1\/4 in. rubber washers, 4 x 1\/4-20 nylock nuts\u003c\/li\u003e\n\u003cli\u003eFasteners for top plate: 6 x 1\/4-20 x 7\/16 in. socket head cap screws, 6 x 1\/4-20 x 3\/8 in. Phillips pan head screws\u003c\/li\u003e\n\u003cli\u003eRetaining clip for securing the handle\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eSafety and compliance\u003c\/h6\u003e\u003cp\u003eCalifornia Proposition 65 warning: This product can expose you to chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm. For more information, visit P65Warnings.ca.gov.\u003c\/p\u003e\n\u003cspan itemprop=\"mpn\" hidden\u003e8M0095972\u003c\/span\u003e","brand":"MotorGuide","offers":[{"title":"Default Title","offer_id":53721590923445,"sku":"QBP425717","price":280.48,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1280714_qbp425717.jpg?v=1794118900"},{"product_id":"qbp425377","title":"MotorGuide Xi Series Quick-Release Bracket, For Xi5 Trolling Motors, White Composite Nylon, Stainless Steel Hardware, Security Clasp for Padlock","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe MotorGuide 8M0092063 is a quick-release bracket that lets you remove an Xi series bow-mount trolling motor from the deck without unbolting the base every time.\u003c\/p\u003e\u003cp\u003eIt’s a two-plate setup: one plate stays attached to the trolling motor mount, and the other stays fastened to the boat. When you need the bow clear for storage, trailering, service, or security, you pull the release pin and lift the motor and top plate off as a single unit.\u003c\/p\u003e\u003cp\u003eThis is the white composite version, built to keep the footprint low on the bow. The mounting hardware is stainless steel, which matters when the bracket lives in spray, washdowns, and day-to-day vibration.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eTwo-plate quick-release system so the deck plate can stay installed while the motor removes cleanly.\u003c\/li\u003e\n\u003cli\u003eWhite composite plates with stainless steel mounting hardware.\u003c\/li\u003e\n\u003cli\u003ePin-lock attachment for fast on-and-off at the dock, at the ramp, or in the garage.\u003c\/li\u003e\n\u003cli\u003eLocking clip can be secured with a padlock to help deter theft and keep the release pin from being pulled (padlock not included).\u003c\/li\u003e\n\u003cli\u003eMounting layout uses M6 hardware and a 6 mm drilled hole pattern, which helps when planning backing plates and under-deck access.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis bracket is intended for MotorGuide Xi series bow-mount trolling motor installations. Fit is determined by the mount’s bolt pattern and the available flat surface area on the bow deck, so it’s worth confirming you have room for the bottom plate and access below the deck for washers and locknuts.\u003c\/p\u003e\u003cp\u003eIf your boat has a thin deck, a backing plate underneath helps spread the load and keeps the mount from working the fasteners loose over time. Also confirm the stowed and deployed positions of the motor still clear rails, hatches, and nav lights once the mount height changes slightly.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eInstallation is straightforward: separate the plates, fasten the top plate to the trolling motor mount, then use the bottom plate as the drill template on the deck. Plan the location so you can reach the release pin and locking clip without leaning over the bow.\u003c\/p\u003e\u003cp\u003eA 6 mm drill bit is used for the deck holes, and common hand tools cover the rest. Seal the holes with marine sealant to protect the core and hardware, and recheck fastener torque after the first few trips as the deck bedding settles.\u003c\/p\u003e\u003ch6\u003eWhat’s included\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eTop plate\u003c\/li\u003e\n\u003cli\u003eBottom plate\u003c\/li\u003e\n\u003cli\u003eRelease pin\u003c\/li\u003e\n\u003cli\u003eLocking clip\u003c\/li\u003e\n\u003cli\u003eStainless steel mounting hardware package\u003c\/li\u003e\n\u003cli\u003e5 mm Allen wrench\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eUse on board\u003c\/h6\u003e\u003cp\u003eThis bracket is a good match for anglers who trailer often, store the motor indoors between trips, or want a cleaner bow when the trolling motor is not needed. It also helps when you need quick access for wiring checks, transducer cable routing, or seasonal maintenance without tearing up the deck fasteners.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eRinse the bracket and hardware after saltwater use, especially around the pin and locking clip. A light wipe-down keeps grit from building up where the plates meet, and a quick inspection of the fasteners during routine checks helps prevent loosening from vibration.\u003c\/p\u003e\u003ch6\u003eSafety and compliance\u003c\/h6\u003e\u003cp\u003eWARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.\u003c\/p\u003e\n\u003cspan itemprop=\"mpn\" hidden\u003e8M0092063\u003c\/span\u003e","brand":"MotorGuide","offers":[{"title":"Default Title","offer_id":53721603244213,"sku":"QBP425377","price":134.42,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1280694_qbp425377.jpg?v=1794119037"},{"product_id":"qbp629656","title":"MotorGuide Machete III Trolling Motor Propeller, 3-Blade, 3.5 in Hub, Glass-Filled","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe MotorGuide MGA089G is a Machete III Tour three-blade trolling motor propeller made from glass-filled material with a 3.5-inch hub size.\u003c\/p\u003e\u003cp\u003eIt is a practical upgrade when you want a prop that stays consistent under load and keeps its shape through long days of spot-locking, repeated boat positioning, and hard steering corrections. The three-blade, tapered-hub profile is built around speed and efficiency, with a clean, quiet bite that helps the motor feel less strained when wind and current pick up.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eThree-blade, tapered-hub profile tuned for speed and efficiency on a trolling motor\u003c\/li\u003e\n\u003cli\u003eGlass-filled construction for higher wear resistance than standard composite props\u003c\/li\u003e\n\u003cli\u003eFits MotorGuide lower units that use the standardized 3.5-inch prop hub\u003c\/li\u003e\n\u003cli\u003eSimple swap for compatible MotorGuide props when you want a tougher material\u003c\/li\u003e\n\u003cli\u003eUses a prop pin and prop nut for secure installation\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eWhat’s included\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003ePropeller\u003c\/li\u003e\n\u003cli\u003eProp pin\u003c\/li\u003e\n\u003cli\u003eProp nut\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis prop is for MotorGuide trolling motors with a 3.5-inch prop hub lower unit. Confirm your current prop hub size before ordering, especially if your boat has had a motor swap or a previous prop change. It is intended for trolling motor use, not outboard or sterndrive applications.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eCut power at the battery or trolling motor plug before working at the lower unit. Remove the existing prop nut and prop, then check for fishing line around the shaft and seals while everything is accessible.\u003c\/p\u003e\u003cp\u003eInstall the prop pin, slide the prop fully into place, and secure it with the prop nut. Tighten the nut to the torque specified for your motor, then spin the prop by hand to confirm it turns freely without rubbing.\u003c\/p\u003e\u003ch6\u003eUse on board\u003c\/h6\u003e\u003cp\u003eThis prop is a good match for anglers who run a bow-mount hard in wind or current and want a prop material that lasts through frequent use. It also suits boats that spend time in skinny water, where props see occasional sand and grass contact and a tougher composite can help reduce downtime.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eAfter trips, clear weeds and wrapped line immediately so the shaft area stays clean. If you run in brackish or saltwater, rinse the lower unit after use and check the prop nut for tightness as part of your regular pre-launch routine.\u003c\/p\u003e\u003ch6\u003eCalifornia Proposition 65 notice\u003c\/h6\u003e\u003cp\u003eWARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects, or other reproductive harm. For more information, visit P65Warnings.ca.gov.\u003c\/p\u003e\n\u003cspan itemprop=\"mpn\" hidden\u003eMGA089G\u003c\/span\u003e","brand":"MotorGuide","offers":[{"title":"Default Title","offer_id":53721604751541,"sku":"QBP629656","price":69.81,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1280725_qbp629656.webp?v=1794119286"},{"product_id":"qbp671030","title":"MotorGuide X3-55FW Bow-Mount Trolling Motor, Hand Control, 55lb Thrust, 50in Shaft, 12V","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe MotorGuide 940200210 is a 12V freshwater bow-mount trolling motor with hand control, 55 lb peak thrust, and a 50 inch shaft. It uses a twist-tiller for speed and direction, with five forward speeds and two reverse speeds, and it pulls up to 49 amps at full output.\u003c\/p\u003e\u003cp\u003eThis setup is a common fit on bass boats and jon boats when you want bow-mounted control without a foot pedal. The 50 inch shaft length is the key fit check, measure from the bow mounting surface down to the waterline and make sure you have enough length to keep the prop submerged when the bow lifts in chop.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e12V freshwater bow mount with 55 lb peak thrust and a 50 inch shaft\u003c\/li\u003e\n\u003cli\u003eHand control with an ergonomic, extendable twist-tiller handle for steering and speed control\u003c\/li\u003e\n\u003cli\u003eFive forward speeds and two reverse speeds, with an off position on the tiller\u003c\/li\u003e\n\u003cli\u003eUp to 49A max amp draw for electrical planning and circuit protection sizing\u003c\/li\u003e\n\u003cli\u003eMachete three-blade prop for everyday weed and open-water trolling scenarios\u003c\/li\u003e\n\u003cli\u003eWide aluminum bracket mount with a latch release handle for stowing and deploying at the bow\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003ePlan the bow mounting position so the motor column clears the bow when stowed and deployed. A practical benchmark is keeping about 3 inches (7.6 cm) of clearance between the bow and the motor column so it can move freely during stow and deploy.\u003c\/p\u003e\u003cp\u003eMount the bracket on a solid, flat section of the deck using at least four mounting bolts, spread as far apart as practical for stability. After installation, set running depth so the prop stays fully submerged, with the blades about 6 to 12 inches (15 to 30 cm) below the surface to reduce ventilation in waves.\u003c\/p\u003e\u003ch6\u003eElectrical and system integration\u003c\/h6\u003e\u003cp\u003eThis is a 12V motor, so it connects to a single 12V battery. Because max draw can reach 49A, keep wiring runs tidy, use appropriate cable gauge for the length of your run, and include proper circuit protection between the battery and the motor.\u003c\/p\u003e\u003cp\u003eOn boats with an existing 24V trolling setup, this model still needs a 12V supply. If your bow already has a breaker panel or battery compartment, double-check that the available circuit matches the motor voltage before committing to the install.\u003c\/p\u003e\u003ch6\u003eUse on board\u003c\/h6\u003e\u003cp\u003eThe twist-tiller control is straightforward for dock approach work, holding on a breakline, or making small heading corrections while fishing. Rotate the handle clockwise for forward, counterclockwise for reverse, and return to off when you want the motor stopped.\u003c\/p\u003e\u003cp\u003eIt is a good match for anglers who prefer hand control at the bow and want a simple 12V system without added electronics or foot-pedal rigging.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eBefore each trip, check the mount hardware for tightness, confirm battery lead connections are secure, and inspect the prop nut. After use, disconnect from the battery, clear weeds or fishing line from the prop and shaft, and rinse with clean water to remove grime that can scratch surfaces.\u003c\/p\u003e\n\u003cspan itemprop=\"mpn\" hidden\u003e940200210\u003c\/span\u003e","brand":"MotorGuide","offers":[{"title":"Default Title","offer_id":53721607766197,"sku":"QBP671030","price":1068.42,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1281405_qbp566813.jpg?v=1794118764"},{"product_id":"qbp829477","title":"MotorGuide Tour Bow-Mount Trolling Motor, 36V, 109 lb Thrust, 45 in Shaft, Cable Steer, Foot Control, HD+ Universal Sonar, Freshwater","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe MotorGuide 942100050 is a freshwater bow-mount trolling motor with cable steering, a 36V power requirement, and an HD+ universal sonar nose cone for fishfinder integration. It is rated for up to 109 lb of thrust and uses a 45 inch shaft, which is a common fit on bass boat bows where you want the prop to stay planted in the water as conditions change.\u003c\/p\u003e\u003cp\u003eCable steer control gives you direct response at the pedal. This model uses a metal foot pedal with a premium no-slip grip, and the mount includes a Zero-G lift assist system to make stowing and deploying more manageable during long days on the bow.\u003c\/p\u003e\u003cp\u003eFor sonar, the hardware is already built into the nose cone and connects using the adapter cable that matches your sonar brand. The mount also incorporates a 360 degree breakaway function, which helps when the motor takes an impact around shallow cover and structure.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e36V freshwater bow-mount motor rated for up to 109 lb of thrust with a 45 inch shaft.\u003c\/li\u003e\n\u003cli\u003eCable steer foot control with a durable metal pedal and a premium no-slip grip.\u003c\/li\u003e\n\u003cli\u003eHD+ universal sonar built into the nose cone; connects using the adapter cable that matches your sonar brand.\u003c\/li\u003e\n\u003cli\u003eZero-G lift assist with Bulldog latches to simplify stow and deploy at the bow.\u003c\/li\u003e\n\u003cli\u003e360 degree breakaway mount for impact situations around cover and shorelines.\u003c\/li\u003e\n\u003cli\u003eIntegrated Bounce Buster and cable routing to control bow bounce and keep routing tidy while running and trailering.\u003c\/li\u003e\n\u003cli\u003eInner composite shaft backed by a lifetime warranty.\u003c\/li\u003e\n\u003cli\u003eTwo-blade Katana prop and lithium-ion battery compatibility.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis unit is set up for freshwater use and is listed for bass boat applications. Before ordering, confirm you have a 36V battery bank and a clean mounting area on the bow where the motor can stow without interfering with an anchor locker lid, rub rail, or bow light.\u003c\/p\u003e\u003cp\u003eShaft length is 45 inches, so it is worth measuring from the bow mounting surface to the waterline and thinking about how you fish. Keeping the prop submerged matters most when you are working wind, boat wakes, or shallow cover where the bow is constantly rising and falling.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003ePlan the pedal position so you can steer comfortably while still reaching the motor controls, and route the steering cables so they do not chafe on sharp edges or get pinched when the mount swings. On the electrical side, keep connections tight, protected from spray, and secured so heavy cables cannot vibrate against the deck.\u003c\/p\u003e\u003cp\u003eIf you are tying the built-in sonar into your electronics, verify the correct adapter cable for your fishfinder brand and route the sonar lead with enough slack for stow and deploy without pulling on the connector.\u003c\/p\u003e\u003ch6\u003eUse on board\u003c\/h6\u003e\u003cp\u003eThis setup is a good fit for anglers who want the feel of cable steering for boat control around docks, grass lines, and timber, while keeping the transducer install clean through the integrated HD+ universal sonar nose cone. It also suits boats that see frequent bow time where quick, repeatable stow and deploy makes a noticeable difference over a season.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eKeep the prop area clear of weeds and fishing line, and check the mount hardware for tightness after trailering. Even on freshwater boats, a quick rinse and wipe-down helps keep the pedal, mount pivots, and lift assist moving freely.\u003c\/p\u003e\n\u003cspan itemprop=\"mpn\" hidden\u003e942100050\u003c\/span\u003e","brand":"MotorGuide","offers":[{"title":"Default Title","offer_id":53721608061109,"sku":"QBP829477","price":1649.98,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1281397_qbp829477.jpg?v=1794119795"},{"product_id":"qbp629645","title":"MotorGuide Power Prop Trolling Motor Propeller, For 3in Hub Trolling Motors, 2-Blade, Black Prop","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe MotorGuide MGA0476B is a 2-blade trolling motor propeller with a 3 inch hub in black. It fits MotorGuide lower units that use the 3 inch diameter hub, including R3 30 lb, 30 inch transom-mount motors.\u003c\/p\u003e\u003cp\u003eUse it as a direct replacement when your current prop has chipped edges, causes vibration, or is not moving the boat the way it used to. A fresh prop is one of the quickest ways to bring back predictable steering and low-speed control.\u003c\/p\u003e\u003cp\u003eBefore ordering, confirm your motor uses the 3 inch hub size. MotorGuide props are not universal across all lower units, so hub diameter is the fast check that prevents a mismatch.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e3 inch hub size for MotorGuide trolling motors that use the 3 inch diameter lower-unit hub\u003c\/li\u003e\n\u003cli\u003e2-blade Power Prop style for solid push and efficient performance at trolling speeds\u003c\/li\u003e\n\u003cli\u003eBlack finish that matches common MotorGuide lower unit color schemes\u003c\/li\u003e\n\u003cli\u003eSupplied as a kit with the propeller, prop pin, and prop nut for a complete swap\u003c\/li\u003e\n\u003cli\u003eCommon fit for R3 30 lb, 30 inch transom-mount motors when the hub size matches\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eWhat’s included\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003ePropeller\u003c\/li\u003e\n\u003cli\u003eProp pin\u003c\/li\u003e\n\u003cli\u003eProp nut\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis prop is sized around a 3 inch hub. If you are replacing an existing MotorGuide prop, verify the hub diameter on your current lower unit or confirm your motor model uses the 3 inch hub family.\u003c\/p\u003e\u003cp\u003eIf your motor takes a different hub size, this prop will not seat correctly on the shaft. Hub diameter and the style of the drive pin slot are the key fit points to check before installing.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eDisconnect power at the battery before working around the prop. Remove the prop nut, slide off the old prop, and inspect the area for fishing line that may have wrapped the shaft. Install the prop pin, align the prop with the pin slot, then reinstall the nut and snug it down. Spin the prop by hand to confirm it turns freely and clears the skeg.\u003c\/p\u003e\u003ch6\u003eUse on board\u003c\/h6\u003e\u003cp\u003eThis prop is a good match for anglers and small-boat owners running a MotorGuide trolling motor with a 3 inch hub who want a straightforward replacement without changing the rest of the setup. It suits the kind of slow-speed work where you are correcting drift, holding a line along the bank, or maneuvering around docks and structure.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eAfter trips, check for weeds or line and clear it right away to protect seals and keep thrust consistent. If you bump bottom or hit debris, inspect the blades for cracks and keep a spare prop kit onboard so a damaged prop does not end the day early.\u003c\/p\u003e\n\u003cspan itemprop=\"mpn\" hidden\u003eMGA0476B\u003c\/span\u003e","brand":"MotorGuide","offers":[{"title":"Default Title","offer_id":53721608388789,"sku":"QBP629645","price":46.53,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1280722_qbp629645.jpg?v=1794119843"},{"product_id":"qbp425889","title":"MotorGuide Xi Series Quick-Release Bracket, For Xi3\/Xi5, Black Composite, Low-Profile, Thread-Locking Clamp, Padlock Security Clasp","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe MotorGuide 8M0120717 is a Xi Series quick-release bracket that lets you mount a bow trolling motor and remove it without unbolting the base.\u003c\/p\u003e\u003cp\u003eThe bracket uses a black composite body with a thread-locking clamp style that helps eliminate noise and movement once it is locked down. It is built for MotorGuide Xi3 and Xi5 bow-mount trolling motors, and the low profile with a small footprint helps keep bow space open.\u003c\/p\u003e\u003cp\u003eA security clasp accepts a padlock so the motor can be locked to the bracket when the boat is unattended.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eFits MotorGuide Xi3 and Xi5 bow-mount trolling motors\u003c\/li\u003e\n\u003cli\u003eQuick-release design for fast removal and reinstallation without pulling deck bolts\u003c\/li\u003e\n\u003cli\u003eThread-locking clamp style helps eliminate noise and movement in use\u003c\/li\u003e\n\u003cli\u003eLow profile with a small footprint to save space on the bow\u003c\/li\u003e\n\u003cli\u003eSecurity clasp accepts a padlock for theft deterrence\u003c\/li\u003e\n\u003cli\u003eCast aluminum and stainless steel hardware used in the bracket assembly\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eWhat’s included\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eQuick-release bracket\u003c\/li\u003e\n\u003cli\u003eMounting hardware\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis bracket is intended for the Xi Series platform and is used with MotorGuide Xi3 and Xi5 bow-mount motors. If you are swapping from a different mount or updating an older bracket, confirm the deck area has clearance for the motor to stow and deploy and that the mounting surface is flat and well supported.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003ePlan the location so the motor can stow cleanly without contacting rub rail, cleats, or bow lights. A solid backing plate under the deck helps spread load on thinner fiberglass and reduces flex over time. After mounting, set the clamp tension so the bracket locks down firmly without forcing the mechanism.\u003c\/p\u003e\u003cp\u003eOn saltwater boats or any deck that sees frequent spray, rinsing the bracket after use and keeping the locking surfaces clean helps the quick-release action stay smooth.\u003c\/p\u003e\u003ch6\u003eSafety and compliance\u003c\/h6\u003e\u003cp\u003eWARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.\u003c\/p\u003e\n\u003cspan itemprop=\"mpn\" hidden\u003e8M0120717\u003c\/span\u003e","brand":"MotorGuide","offers":[{"title":"Default Title","offer_id":53721612812469,"sku":"QBP425889","price":134.42,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1280715_qbp425889.jpg?v=1794120255"},{"product_id":"qbp417531","title":"MotorGuide Lowrance 9-Pin HD+ Sonar Adapter Cable, For Tour \u0026 Tour Pro HD+ Motors, For Lowrance HDS Live\/Carbon \u0026 Elite Ti\/Ti2 \u0026 Elite FS, Black 9-Pin Xsonic Port, 83\/200 \u0026 455\/800 kHz, Not for Xi Series Motors","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe MotorGuide 8M4004174 is a Lowrance 9-pin HD+ sonar adapter cable for Tour and Tour Pro HD+ enabled trolling motors, letting your Lowrance display read sonar from the transducer beneath the motor.\u003c\/p\u003e\u003cp\u003eIt supports 83\/200 kHz and 455\/800 kHz sonar frequencies for clear 2D and HD views under the bow, using the black 9-pin Xsonic transducer port found on compatible Lowrance units.\u003c\/p\u003e\u003cp\u003eThis adapter is only for Tour and Tour Pro motors with HD+ sonar support, and it is not compatible with Xi Series motors.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eConnects HD+ sonar from Tour and Tour Pro trolling motors to a Lowrance black 9-pin Xsonic transducer port\u003c\/li\u003e\n\u003cli\u003eSupports 83\/200 kHz and 455\/800 kHz sonar frequencies for 2D and HD views beneath the trolling motor\u003c\/li\u003e\n\u003cli\u003eCompatible with Lowrance HDS and Elite Ti2 displays that use the black 9-pin Xsonic transducer connector\u003c\/li\u003e\n\u003cli\u003eNot compatible with Xi Series motors\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis cable is a match when your boat is rigged with a Tour or Tour Pro motor that is HD+ sonar enabled, and your Lowrance display has the black 9-pin Xsonic transducer port. If your display uses a different transducer connector style, this adapter will not plug in.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eRoute the cable along the trolling motor harness so it can stow and deploy without pulling on the connectors. Keep the connection point where it stays out of standing water, and leave a small drip loop so water does not track into the plug during washdowns or rain.\u003c\/p\u003e\u003cp\u003eAfter installation, set the sonar source on the display to the trolling motor transducer so readings come from beneath the bow rather than another transducer on the boat.\u003c\/p\u003e\u003ch6\u003eOn-board use\u003c\/h6\u003e\u003cp\u003eThis adapter makes sense for anglers running a bow-mounted Lowrance unit who want sonar under the trolling motor for positioning on structure, staying on contour, and watching bottom changes while they work the front deck.\u003c\/p\u003e\u003ch6\u003eSafety note\u003c\/h6\u003e\u003cp\u003eCalifornia Proposition 65 warning: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.\u003c\/p\u003e\n\u003cspan itemprop=\"mpn\" hidden\u003e8M4004174\u003c\/span\u003e","brand":"MotorGuide","offers":[{"title":"Default Title","offer_id":53721614844085,"sku":"QBP417531","price":77.54,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1280689_qbp417531.jpg?v=1794120585"},{"product_id":"qbp417630","title":"MotorGuide Raymarine Axiom HD+ Sonar Adapter Cable, For Tour\/Tour Pro HD+, 2D 83\/200 kHz","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe MotorGuide 8M4004180 is a sonar adapter cable that lets a Raymarine Axiom display read the 2D 83\/200 kHz sonar signal from a MotorGuide Tour or Tour Pro HD+ trolling motor.\u003c\/p\u003e\u003cp\u003eIt is meant for setups where the sonar source is at the bow under the trolling motor, and you want that return on an Axiom (including Axiom Pro) without changing transducers or cutting wiring. This connection is for 2D sonar only, so you will be working with traditional depth and fish-arch views at 83\/200 kHz.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003eConnects MotorGuide Tour and Tour Pro HD+ enabled motors to Raymarine Axiom and Axiom Pro sonar inputs\u003c\/li\u003e\n\u003cli\u003e2D sonar only at 83\/200 kHz\u003c\/li\u003e\n\u003cli\u003eInterfaces through the standard MotorGuide blue\/gray 7-pin sonar connector on the motor side\u003c\/li\u003e\n\u003cli\u003eSimple plug connection with no splicing required\u003c\/li\u003e\n\u003cli\u003eNot compatible with MotorGuide Xi Series motors\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eCompatibility and fit\u003c\/h6\u003e\u003cp\u003eThis adapter is intended for Tour and Tour Pro models that are HD+ enabled. It is not a match for Xi Series motors, and it is not meant for non HD+ trolling motor sonar setups. On the display side, it is built for the Raymarine Axiom family, including Axiom Pro, for 2D sonar viewing.\u003c\/p\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eConnect the MotorGuide end to the trolling motor sonar lead, then connect the Raymarine end to the Axiom transducer port. After powering up, select a 2D sonar view and confirm the frequency options are set up for 83\/200 kHz so the unit is looking at the right channel.\u003c\/p\u003e\u003cp\u003eRoute the cable so it can move with the shaft when you deploy and stow the motor. Leave a little slack at the pivot points and secure the run so it will not get pinched by the mount, rub on the steering collar, or snag when the motor is trimmed and strapped down for a run across chop.\u003c\/p\u003e\u003ch6\u003eUse on board\u003c\/h6\u003e\u003cp\u003eThis is a good fit for anglers running a bow-mounted Tour or Tour Pro HD+ who want their Raymarine Axiom at the bow to show bottom tracking and fish targets directly under the trolling motor. It also works well for boats where you want a clean install with the sonar source up front, rather than adding a second transducer and cable run.\u003c\/p\u003e\n\u003cspan itemprop=\"mpn\" hidden\u003e8M4004180\u003c\/span\u003e","brand":"MotorGuide","offers":[{"title":"Default Title","offer_id":53721616842933,"sku":"QBP417630","price":93.04,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1280693_qbp417630.jpg?v=1794120809"}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/collections\/f2243c25-3fa3-5210-8844-eae1df8d365d.webp?v=1794118082","url":"https:\/\/www.qualityboatparts.com\/collections\/brand-motorguide.oembed","provider":"Quality Boat Parts","version":"1.0","type":"link"}