{"title":"i2Systems","description":"","products":[{"product_id":"qbp512991","title":"i2Systems Apeiron Pro A503 Spring Mount LED Downlight, 3W, 9-30VDC, IP67, Square\/Square, Neutral White, Polished Chrome Finish","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe i2Systems A503-14BBD is a 3W spring-mount recessed LED downlight with a square\/square polished chrome bezel and a neutral white output (4000K). It runs on 9-30V DC for typical 12V and 24V boat systems, puts out about 150 lumens with a 120 degree beam, and carries an IP67 rating for wet locations and washdowns.\u003c\/p\u003e\u003cp\u003eThis size is commonly used as a general overhead light in cabins, heads, companionways, and pilothouses. The diffuser keeps the light even and reduces the “hot spot” look you get with some bare-LED fixtures, which helps in low ceilings and tight spaces.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e3W output with about 150 lumens typical and a 120 degree beam angle for general interior lighting\u003c\/li\u003e\n\u003cli\u003eNeutral white 4000K LED color for a clean, natural look on board\u003c\/li\u003e\n\u003cli\u003e9-30V DC input for both 12V and 24V systems\u003c\/li\u003e\n\u003cli\u003eIP67-rated for wet locations and washdowns; not intended for submersible mounting or areas with standing water\u003c\/li\u003e\n\u003cli\u003eSquare\/square bezel with polished chrome finish (PVD titanium) and stainless steel trim\u003c\/li\u003e\n\u003cli\u003e3.15 in (80 mm) face size with a 2.44 in (62 mm) cutout requirement and about 1.37 in (35 mm) mounting depth\u003c\/li\u003e\n\u003cli\u003e9 in lead length using 18 AWG conductors, plus a separate dimming control lead when used with compatible controls\u003c\/li\u003e\n\u003cli\u003eBuilt-in protection including surge suppression, reverse polarity protection, and an auto-reset fuse\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eThis light uses spring clips for mounting. Plan the cutout carefully and confirm you have enough clearance behind the panel for the housing depth, plus room for the wiring to bend without being pinched by the springs.\u003c\/p\u003e\u003cp\u003eIn damp areas, it is good practice to keep water from pooling around the back of the fixture and to seal any nearby wiring openings so moisture cannot collect in the cavity.\u003c\/p\u003e\u003ch6\u003eElectrical and dimming\u003c\/h6\u003e\u003cp\u003ePower is DC only. For basic on\/off operation, wire the main power leads to your vessel’s lighting circuit and protect the circuit with the appropriate overcurrent protection for your installation.\u003c\/p\u003e\u003cp\u003eIf you are integrating dimming, use the dimming control lead as intended by your controller and keep the control line at or below 30V DC. Many onboard lighting systems that dim via PWM can drive the control input, so you can keep the same fixture style while moving from a simple switch to a dimmer later.\u003c\/p\u003e\u003ch6\u003eMaterials and water exposure\u003c\/h6\u003e\u003cp\u003eThe trim is stainless steel with an anodized aluminum housing, and the lens is tempered glass with a diffuser. The polished chrome finish is a PVD titanium coating, which helps it hold up in humid cabins and saltwater environments where plated finishes can discolor over time.\u003c\/p\u003e\u003cp\u003eIP67 helps for spray and washdowns, but it should not be installed where it will sit underwater or in a location that can trap standing water.\u003c\/p\u003e\u003ch6\u003eUse cases on board\u003c\/h6\u003e\u003cp\u003eThis configuration is a good fit when you want a clean neutral white overhead light and a square trim to match other interior hardware. It is commonly used in cabins, galleys, passageways, and enclosed helm areas where you want wide, even light without a narrow spotlight effect.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eWipe the bezel and lens with a soft cloth and mild cleaner. Avoid abrasive pads that can scratch the finish and reduce light clarity over time.\u003c\/p\u003e\n\u003cspan itemprop=\"mpn\" hidden\u003eA503-14BBD\u003c\/span\u003e","brand":"i2Systems","offers":[{"title":"Default Title","offer_id":53721528565941,"sku":"QBP512991","price":134.44,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1281368_qbp512991.jpg?v=1794116471"},{"product_id":"qbp536261","title":"i2Systems Apeiron A1110Z LED Spring Mount Downlight, Square\/Square Bezel, Brushed Nickel Finish, 6500K Cool White, 9-30V DC, IP67, 4.5W","description":"\u003ch6\u003eOverview\u003c\/h6\u003e\u003cp\u003eThe i2Systems AP-4W-65K-PW44 is a recessed Apeiron A1110Z LED downlight with a square\/square brushed nickel trim and a 6500K cool white output. It runs on 9 to 30V DC and draws 4.5W, so it fits typical 12V and 24V onboard systems. The fixed 120° beam spreads light across a broad area, which works well for general overhead lighting rather than a tight spotlight effect.\u003c\/p\u003e\u003cp\u003eThis fixture uses spring clips for a clean, screw-free installation. Plan for a 2.75 in (70 mm) cutout and about 1.24 in (32 mm) of mounting depth, with the finished trim covering a 3.15 in (80 mm) square footprint. The housing is IP67 rated for damp and wet locations, but it is not meant for submersion or spots where water can stand.\u003c\/p\u003e\u003ch6\u003eKey features\u003c\/h6\u003e\u003cul\u003e\n\u003cli\u003e9 to 30V DC input for 12V and 24V electrical systems\u003c\/li\u003e\n\u003cli\u003e4.5W LED downlight with 6500K cool white appearance\u003c\/li\u003e\n\u003cli\u003eSquare\/square trim in brushed nickel finish for a modern, clean look\u003c\/li\u003e\n\u003cli\u003eSpring-clip recessed mounting with a 2.75 in (70 mm) cutout and 1.24 in (32 mm) depth requirement\u003c\/li\u003e\n\u003cli\u003eIP67 rated for damp and wet locations; not intended for submersible installs or areas with standing water\u003c\/li\u003e\n\u003cli\u003e120° fixed beam for general lighting across cabins, heads, and covered exterior spaces\u003c\/li\u003e\n\u003cli\u003eSimple power wiring plus an optional dimming control lead for 0 to 100% dimming (PWM 100 to 300 Hz, max 30V)\u003c\/li\u003e\n\u003cli\u003eBuilt-in safeguards including reverse polarity protection, transient protection, and an auto-reset fuse\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch6\u003eInstallation and setup\u003c\/h6\u003e\u003cp\u003eMark the cutout carefully and dry-fit the light before final wiring, especially in thin headliners or composite panels where spring clips need solid bite. Leave a little service loop so the fixture can be pulled down later without straining the cable, and keep the wiring compartment dry and accessible.\u003c\/p\u003e\u003cp\u003eFor exterior or washdown-prone areas, seal the cutout edge and any nearby junction points so moisture cannot migrate into void spaces. Avoid mounting locations that see constant runoff or direct high-pressure spray, and do not install where water can pool behind the panel.\u003c\/p\u003e\u003ch6\u003eElectrical and dimming integration\u003c\/h6\u003e\u003cp\u003ePower is straightforward on DC systems: connect positive feed to the red lead and ground to the black lead. If you are using dimming, the yellow lead is the control input. Keep all control signals within 30V DC maximum, and confirm your dimmer output type and frequency are compatible with PWM control.\u003c\/p\u003e\u003ch6\u003eUse on board\u003c\/h6\u003e\u003cp\u003eThis configuration is a good match when you want a cooler, whiter light for detail work and clean visibility in places like a galley, head, companionway, pilot house, or under a hardtop. The square brushed nickel trim also pairs nicely with modern hardware and stainless accents in newer builds and refits.\u003c\/p\u003e\u003ch6\u003eMaintenance and care\u003c\/h6\u003e\u003cp\u003eWipe the trim and lens with a damp cloth and mild soap, then rinse with fresh water in salt environments. Check the cutout seal and wiring area during routine onboard inspections, especially if the light lives in a damp headliner or a covered exterior space.\u003c\/p\u003e\n\u003cspan itemprop=\"mpn\" hidden\u003eAP-4W-65K-PW44\u003c\/span\u003e","brand":"i2Systems","offers":[{"title":"Default Title","offer_id":53721603145909,"sku":"QBP536261","price":130.6,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/files\/1281370_qbp536261.jpg?v=1794119029"}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0977\/8171\/1029\/collections\/97aa0c53-af65-5550-8ed3-18391b876cf4.webp?v=1794118093","url":"https:\/\/www.qualityboatparts.com\/collections\/brand-i2systems.oembed","provider":"Quality Boat Parts","version":"1.0","type":"link"}